- 06 Feb, 2019 10 commits
-
-
Konstantin Khlebnikov authored
I'm seeing series of e1000e resets (sometimes endless) at system boot if something generates tx traffic at this time. In my case this is netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames" from e1000e itself. As result e1000_watchdog_task sees used tx buffer while carrier is off and start this reset cycle again. [ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000 [ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 27.174495] 8021q: 802.1Q VLAN Support v1.8 [ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1 [ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation [ 30.898564] netpoll: netconsole: local port 6666 [ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8 [ 30.898567] netpoll: netconsole: interface 'eth1' [ 30.898568] netpoll: netconsole: remote port 6666 [ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790 [ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0 [ 30.917747] console [netcon0] enabled [ 30.917749] netconsole: network logging started [ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames [ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None This patch flushes tx buffers only once when carrier is off rather than at each watchdog iteration. Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Remove the 'igc_get_link_up_info_base method' from igc_base.c file. Use the 'igc_get_speed_and_duplex_copper' method directly and reduce the code redundancy. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Remove unused igc_adv_data_desc definition from igc_base.h file. Descriptors definition will be added per demand. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jeff Kirsher authored
The change is based on the issue found by Kangjie Lu <kjlu@umn.edu> where we not checking the return value of a register read/write which could result in a NULL pointer dereference if the read/write fails. Since we are only trying to disable the far-end loopback, if the read and write of register fails, we do not want to bail out of the function. We just want to log that it failed to disable and continue on. CC: Sasha Neftin <sasha.neftin@intel.com> CC: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
The function comment for fm10k_iov_msg_msix_pf has an extra space in a sentence, which is unnecessary. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jiri Kosina authored
ixgbe_reset_hw_82599() resets the value of hw->mac.num_rar_entries to pre-defined value of 128. Let's get rid of that hardcoded literal, and use IXGBE_82599_RAR_ENTRIES instead, the same way the normal initialization path does. Signed-off-by: Jiri Kosina <jkosina@suse.cz> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Remove redundant igc_check_for_link_base code and replace it with an igc_check_for_copper_link method. Fix duplication of IGC_ADVTXD_PAYLEN_SHIFT mask declaration. Remove obsolete IGC_SCVPC register definition. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mike Rapoport authored
The documentation of Intel drivers is missing the heading adornment for document titles. This causes the generated html to have TOC entries from these documents to appear as top level TOC entries: * Linux* Base Driver for Intel(R) Ethernet Network Connection * Contents * Identifying Your Adapter * Command Line Parameters * AutoNeg * Duplex ... Add overline heading adornment to document titles. Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Address community comment. Remove the unreachable code leads to the static checker warning. PHY functionality will be added later per demand. Reported by Dan Carpenter. Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Kai-Heng Feng authored
e1000e sets different WoL settings in system suspend callback and runtime suspend callback. The suspend direct complete optimization leaves e1000e in runtime suspended state with wrong WoL setting during system suspend. To fix this, we need to disable suspend direct complete optimization to let e1000e always use suspend callback to set correct WoL during system suspend. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 05 Feb, 2019 8 commits
-
-
Russell King authored
Sven Auhagen reports that if he changes a SFP+ module for a SFP module on the Macchiatobin Single Shot, the link does not come back up. For Sven, it is as easy as: - Insert a SFP+ module connected, and use ping6 to verify link is up. - Remove SFP+ module - Insert SFP 1000base-X module use ping6 to verify link is up: Link up event did not trigger and the link is down but that doesn't show the problem for me. Locally, this has been reproduced by: - Boot with no modules. - Insert SFP+ module, confirm link is up. - Replace module with 25000base-X module. Confirm link is up. - Set remote end down, link is reported as dropped at both ends. - Set remote end up, link is reported up at remote end, but not local end due to lack of link interrupt. Fix this by setting up both GMAC and XLG interrupts for port 0, but only unmasking the appropriate interrupt according to the current mode set in the mac_config() method. However, only do the mask/unmask dance when we are really changing the link mode to avoid missing any link interrupts. Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
Use the phy_interface_mode_is_8023z() helper for detecting interface modes that use 802.3z serial encoding. This is equivalent to testing for both 1000base-X and 2500base-X. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Moritz Fischer says: ==================== nixge: Fixed-link support This series adds fixed-link support to nixge. The first patch corrects the binding to correctly reflect hardware that does not come with MDIO cores instantiated. The second patch adds fixed link support to the driver. The third patch updates the binding document with the now optional (formerly required) phy-handle property and references the fixed-link docs. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Moritz Fischer authored
Update device-tree binding with fixed-link support. With fixed-link support the formerly required property 'phy-handle' is now optional if 'fixed-link' child is present. Signed-off-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Moritz Fischer authored
Add support for fixed-link configurations to nixge driver. Signed-off-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Moritz Fischer authored
Make MDIO child optional and only instantiate the MDIO bus if the child is actually present. There are currently no (in-tree) users of this binding; all (out-of-tree) users use overlays that get shipped together with the FPGA images that contain the IP. This will significantly increase maintainabilty of future revisions of this IP. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Linus Walleij authored
All users of the fixed_phy_add() pass -1 as GPIO number to the fixed phy driver, and all users of fixed_phy_register() pass -1 as GPIO number as well, except for the device tree MDIO bus. Any new users should create a proper device and pass the GPIO as a descriptor associated with the device so delete the GPIO argument from the calls and drop the code looking requesting a GPIO in fixed_phy_add(). In fixed phy_register(), investigate the "fixed-link" node and pick the GPIO descriptor from "link-gpios" if this property exists. Move the corresponding code out of of_mdio.c as the fixed phy code anyways requires OF to be in use. Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tonghao Zhang authored
Add the tab before '}' and keep the code style consistent. Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 04 Feb, 2019 12 commits
-
-
David S. Miller authored
Sergei Shtylyov says: ==================== sh_eth: implement simple RX checksum offload Here's a set of 7 patches against DaveM's 'net-next.git' repo. I'm implemeting the simple RX checksum offload (like was done for the 'ravb' driver by Simon Horman); it has been only tested on the R8A7740 and R8A77980 SoCs, the other SoCs should just work (according to their manuals)... ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
The SH7763 SoC manual describes the Ether MAC's RX checksum offload the same way as it's implemented in the EtherAVB MACs... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
The SH7734 SoC manual describes the Ether MAC's RX checksum offload the same way as it's implemented in the EtherAVB MACs... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
The R-Car V3H (R8A77980) SoC manual describes the Ether MAC's RX checksum offload the same way as it's implemented in the EtherAVB MAC... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
The R-Mobile A1 (R8A7740) SoC manual describes the Ether MAC's RX checksum offload the same way as it's implemented in the EtherAVB MAC... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
The RZ/A1H (R7S721000) SoC manual describes the Ether MAC's RX checksum offload the same way as it's implemented in the EtherAVB MACs... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
Add support for the RX checksum offload. This is enabled by default and may be disabled and re-enabled using 'ethtool': # ethtool -K eth0 rx off # ethtool -K eth0 rx on Some Ether MACs provide a simple checksumming scheme which appears to be completely compatible with CHECKSUM_COMPLETE: sum of all packet data after the L2 header is appended to packet data; this may be trivially read by the driver and used to update the skb accordingly. The same checksumming scheme is implemented in the EtherAVB MACs and now supported by the 'ravb' driver. In terms of performance, throughput is close to gigabit line rate with the RX checksum offload both enabled and disabled. The 'perf' output, however, appears to indicate that significantly less time is spent in do_csum() -- this is as expected. Test results with RX checksum offload enabled: ~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4 TCP MAERTS TEST to 192.168.2.4 Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 131072 16384 16384 10.01 933.93 [ perf record: Woken up 8 times to write data ] [ perf record: Captured and wrote 1.955 MB perf.data (41940 samples) ] ~/netperf-2.2pl4# perf report Samples: 41K of event 'cycles:ppp', Event count (approx.): 9915302763 Overhead Command Shared Object Symbol 9.44% netperf [kernel.kallsyms] [k] __arch_copy_to_user 7.75% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq 6.31% swapper [kernel.kallsyms] [k] default_idle_call 5.89% swapper [kernel.kallsyms] [k] arch_cpu_idle 4.37% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit 4.02% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq 2.52% netperf [kernel.kallsyms] [k] preempt_count_sub 1.81% netperf [kernel.kallsyms] [k] tcp_recvmsg 1.80% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irqres 1.78% netperf [kernel.kallsyms] [k] preempt_count_add 1.36% netperf [kernel.kallsyms] [k] __tcp_transmit_skb 1.20% netperf [kernel.kallsyms] [k] __local_bh_enable_ip 1.10% netperf [kernel.kallsyms] [k] sh_eth_start_xmit Test results with RX checksum offload disabled: ~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4 TCP MAERTS TEST to 192.168.2.4 Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 131072 16384 16384 10.01 932.04 [ perf record: Woken up 14 times to write data ] [ perf record: Captured and wrote 3.642 MB perf.data (78817 samples) ] ~/netperf-2.2pl4# perf report Samples: 78K of event 'cycles:ppp', Event count (approx.): 18091442796 Overhead Command Shared Object Symbol 7.00% swapper [kernel.kallsyms] [k] do_csum 3.94% swapper [kernel.kallsyms] [k] sh_eth_poll 3.83% ksoftirqd/0 [kernel.kallsyms] [k] do_csum 3.23% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq 2.87% netperf [kernel.kallsyms] [k] __arch_copy_to_user 2.86% swapper [kernel.kallsyms] [k] arch_cpu_idle 2.13% swapper [kernel.kallsyms] [k] default_idle_call 2.12% ksoftirqd/0 [kernel.kallsyms] [k] sh_eth_poll 2.02% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore 1.84% swapper [kernel.kallsyms] [k] __softirqentry_text_start 1.64% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit 1.53% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq 1.32% netperf [kernel.kallsyms] [k] preempt_count_sub 1.27% swapper [kernel.kallsyms] [k] __pi___inval_dcache_area 1.22% swapper [kernel.kallsyms] [k] check_preemption_disabled 1.01% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore The above results collected on the R-Car V3H Starter Kit board. Based on the commit 4d86d381 ("ravb: RX checksum offload")... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
Commit 62e04b7e ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed the field to 'hw_checksum' for the Ether DMAC "intelligent checksum", however some Ether MACs implement a simpler checksumming scheme, so that name now seems misleading. Rename that field to 'csmr' as the "intelligent checksum" is always controlled by the CSMR register. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Rothwell authored
Fixes: 887feae3 ("socket: Add SO_TIMESTAMP[NS]_NEW") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joe Perches authored
Add __cold to the netdev_<level> logging functions similar to the use of __cold in the generic printk function. Using __cold moves all the netdev_<level> logging functions out-of-line possibly improving code locality and runtime performance. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
net/core/sock.c: In function 'sock_setsockopt': net/core/sock.c:914:3: warning: this statement may fall through [-Wimplicit-fallthrough=] sock_set_flag(sk, SOCK_TSTAMP_NEW); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ net/core/sock.c:915:2: note: here case SO_TIMESTAMPING_OLD: ^~~~ Fixes: 9718475e ("socket: Add SO_TIMESTAMPING_NEW") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Masahiro Yamada authored
Currently, the header search paths -Itools/include and -Itools/include/uapi are not used. Let's drop the unused code. We can remove -I. too by fixing up one C file. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 03 Feb, 2019 10 commits
-
-
David S. Miller authored
Heiner Kallweit says: ==================== net: phy: aquantia: number of improvements This patch series is based on work from Andrew. I adjusted and added certain parts. The series improves few aspects of driver, no functional change intended. v2: - add my SoB to patch 1 - leave kernel.h in in patch 2 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Replace magic numbers with proper constants. The original patch is from Andrew, I extended / adjusted certain parts: - Use decimal bit numbers. The datasheet uses hex bit numbers 0 .. F. - Order defines from highest to lowest bit numbers - correct some typos - add constant MDIO_AN_TX_VEND_INT_MASK2_LINK - Remove few functional improvements from the patch, they will come as a separate patch. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Make use of macro PHY_ID_MATCH_MODEL to simplify the code. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Remove unneeded header includes. v2: - leave kernel.h in Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
aquantia_ as a name space prefix is rather long, resulting in lots of lines needing wrapping, reducing readability. Use the prefix aqr_ instead, which fits with the vendor naming there devices aqr107, for example. v2: - add SoB from Heiner Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
After 4effd28c ("bridge: join all-snoopers multicast address"), I started seeing the following sleep in atomic warnings: [ 26.763893] BUG: sleeping function called from invalid context at mm/slab.h:421 [ 26.771425] in_atomic(): 1, irqs_disabled(): 0, pid: 1658, name: sh [ 26.777855] INFO: lockdep is turned off. [ 26.781916] CPU: 0 PID: 1658 Comm: sh Not tainted 5.0.0-rc4 #20 [ 26.787943] Hardware name: BCM97278SV (DT) [ 26.792118] Call trace: [ 26.794645] dump_backtrace+0x0/0x170 [ 26.798391] show_stack+0x24/0x30 [ 26.801787] dump_stack+0xa4/0xe4 [ 26.805182] ___might_sleep+0x208/0x218 [ 26.809102] __might_sleep+0x78/0x88 [ 26.812762] kmem_cache_alloc_trace+0x64/0x28c [ 26.817301] igmp_group_dropped+0x150/0x230 [ 26.821573] ip_mc_dec_group+0x1b0/0x1f8 [ 26.825585] br_ip4_multicast_leave_snoopers.isra.11+0x174/0x190 [ 26.831704] br_multicast_toggle+0x78/0xcc [ 26.835887] store_bridge_parm+0xc4/0xfc [ 26.839894] multicast_snooping_store+0x3c/0x4c [ 26.844517] dev_attr_store+0x44/0x5c [ 26.848262] sysfs_kf_write+0x50/0x68 [ 26.852006] kernfs_fop_write+0x14c/0x1b4 [ 26.856102] __vfs_write+0x60/0x190 [ 26.859668] vfs_write+0xc8/0x168 [ 26.863059] ksys_write+0x70/0xc8 [ 26.866449] __arm64_sys_write+0x24/0x30 [ 26.870458] el0_svc_common+0xa0/0x11c [ 26.874291] el0_svc_handler+0x38/0x70 [ 26.878120] el0_svc+0x8/0xc while toggling the bridge's multicast_snooping attribute dynamically. Pass a gfp_t down to igmpv3_add_delrec(), introduce __igmp_group_dropped() and introduce __ip_mc_dec_group() to take a gfp_t argument. Similarly introduce ____ip_mc_inc_group() and __ip_mc_inc_group() to allow caller to specify gfp_t. IPv6 part of the patch appears fine. Fixes: 4effd28c ("bridge: join all-snoopers multicast address") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Shared buffer allocation is usually done in cell increments. Drivers will either round up the allocation or refuse the configuration if it's not an exact multiple of cell size. Drivers know exactly the cell size of shared buffer, so help out users by providing this information in dumps. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Deepa Dinamani says: ==================== net: y2038-safe socket timestamps The series introduces new socket timestamps that are y2038 safe. The time data types used for the existing socket timestamp options: SO_TIMESTAMP, SO_TIMESTAMPNS and SO_TIMESTAMPING are not y2038 safe. The series introduces SO_TIMESTAMP_NEW, SO_TIMESTAMPNS_NEW and SO_TIMESTAMPING_NEW to replace these. These new timestamps can be used on all architectures. The alternative considered was to extend the sys_setsockopt() by using the flags. We did not receive any strong opinions about either of the approaches. Hence, this was chosen, as glibc folks preferred this. The series does not deal with updating the internal kernel socket calls like rxrpc to make them y2038 safe. This will be dealt with separately. Note that the timestamps behavior already does not match the man page specific behavior: SIOCGSTAMP This ioctl should only be used if the socket option SO_TIMESTAMP is not set on the socket. Otherwise, it returns the timestamp of the last packet that was received while SO_TIMESTAMP was not set, or it fails if no such packet has been received, (i.e., ioctl(2) returns -1 with errno set to ENOENT). The recommendation is to update the man page to remove the above statement. The overview of the socket timestamp series is as below: 1. Delete asm specific socket.h when possible. 2. Support SO/SCM_TIMESTAMP* options only in userspace. 3. Rename current SO/SCM_TIMESTAMP* to SO/SCM_TIMESTAMP*_OLD. 3. Alter socket options so that SOCK_RCVTSTAMPNS does not rely on SOCK_RCVTSTAMP. 4. Introduce y2038 safe types for socket timestamp. 5. Introduce new y2038 safe socket options SO/SCM_TIMESTAMP*_NEW. 6. Intorduce new y2038 safe socket timeout options. Changes since v4: * Fixed the typo in calling sock_get_timeout() Changes since v3: * Rebased onto net-next and fixups as per review comments * Merged the socket timeout series * Integrated Arnd's patch to simplify compat handling of timeout syscalls Changes since v2: * Removed extra functions to reduce diff churn as per code review Changes since v1: * Dropped the change to disentangle sock flags * Renamed sock_timeval to __kernel_sock_timeval * Updated a few comments * Added documentation changes ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Deepa Dinamani authored
Add new socket timeout options that are y2038 safe. Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: ccaulfie@redhat.com Cc: davem@davemloft.net Cc: deller@gmx.de Cc: paulus@samba.org Cc: ralf@linux-mips.org Cc: rth@twiddle.net Cc: cluster-devel@redhat.com Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-alpha@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: linux-parisc@vger.kernel.org Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
-
Deepa Dinamani authored
SO_RCVTIMEO and SO_SNDTIMEO socket options use struct timeval as the time format. struct timeval is not y2038 safe. The subsequent patches in the series add support for new socket timeout options with _NEW suffix that will use y2038 safe data structures. Although the existing struct timeval layout is sufficiently wide to represent timeouts, because of the way libc will interpret time_t based on user defined flag, these new flags provide a way of having a structure that is the same for all architectures consistently. Rename the existing options with _OLD suffix forms so that the right option is enabled for userspace applications according to the architecture and time_t definition of libc. Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Cc: ccaulfie@redhat.com Cc: deller@gmx.de Cc: paulus@samba.org Cc: ralf@linux-mips.org Cc: rth@twiddle.net Cc: cluster-devel@redhat.com Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-alpha@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: linux-parisc@vger.kernel.org Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
-