- 30 Sep, 2015 40 commits
-
-
Richard Laing authored
commit 25b4a44c upstream. In the IPv6 multicast routing code the mrt_lock was not being released correctly in the MFC iterator, as a result adding or deleting a MIF would cause a hang because the mrt_lock could not be acquired. This fix is a copy of the code for the IPv4 case and ensures that the lock is released correctly. Signed-off-by:
Richard Laing <richard.laing@alliedtelesis.co.nz> Acked-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Eugene Shatokhin authored
commit f50791ac upstream. It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in usbnet_stop(), but its value should be read before it is cleared when dev->flags is set to 0. The problem was spotted and the fix was provided by Oliver Neukum <oneukum@suse.de>. Signed-off-by:
Eugene Shatokhin <eugene.shatokhin@rosalab.ru> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Kevin Cernekee authored
commit 98fb1ffd upstream. Block drivers are responsible for calling flush_dcache_page() on each BIO request. This operation keeps the I$ coherent with the D$ on architectures that don't have hardware coherency support. Without this flush, random crashes are seen when executing user programs from an ext4 filesystem backed by a ubiblock device. This patch is based on the change implemented in commit 2d4dc890 ("block: add helpers to run flush_dcache_page() against a bio and a request's pages"). Fixes: 9d54c8a3 ("UBI: R/O block driver on top of UBI volumes") Signed-off-by:
Kevin Cernekee <cernekee@chromium.org> Signed-off-by:
Ezequiel Garcia <ezequiel.garcia@imgtec.com> Signed-off-by:
Richard Weinberger <richard@nod.at> [ luis: backported to 3.16: used Kevin's backport to 3.14 ] Signed-off-by:
-
Sasha Levin authored
commit 74e98eb0 upstream. There was no verification that an underlying transport exists when creating a connection, this would cause dereferencing a NULL ptr. It might happen on sockets that weren't properly bound before attempting to send a message, which will cause a NULL ptr deref: [135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [135546.051270] Modules linked in: [135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527 [135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000 [135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194) [135546.055666] RSP: 0018:ffff8800bc70fab0 EFLAGS: 00010202 [135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000 [135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038 [135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000 [135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000 [135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000 [135546.061668] FS: 00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000 [135546.062836] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0 [135546.064723] Stack: [135546.065048] ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008 [135546.066247] 0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342 [135546.067438] 1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00 [135546.068629] Call Trace: [135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134) [135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298) [135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278) [135546.071981] rds_sendmsg (net/rds/send.c:1058) [135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38) [135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298) [135546.074577] ? rds_send_drop_to (net/rds/send.c:976) [135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795) [135546.076349] ? __might_fault (mm/memory.c:3795) [135546.077179] ? rds_send_drop_to (net/rds/send.c:976) [135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620) [135546.078856] SYSC_sendto (net/socket.c:1657) [135546.079596] ? SYSC_connect (net/socket.c:1628) [135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926) [135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674) [135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16) [135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16) [135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1 Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Paul Mackerras authored
commit e297c939 upstream. This fixes a race which can result in the same virtual IRQ number being assigned to two different MSI interrupts. The most visible consequence of that is usually a warning and stack trace from the sysfs code about an attempt to create a duplicate entry in sysfs. The race happens when one CPU (say CPU 0) is disposing of an MSI while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls (for example) pnv_teardown_msi_irqs(), which calls msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its hardware IRQ number) is no longer in use. Then, before CPU 0 gets to calling irq_dispose_mapping() to free up the virtal IRQ number, CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an MSI, and gets the same hardware IRQ number that CPU 0 just freed. CPU 1 then calls irq_create_mapping() to get a virtual IRQ number, which sees that there is currently a mapping for that hardware IRQ number and returns the corresponding virtual IRQ number (which is the same virtual IRQ number that CPU 0 was using). CPU 0 then calls irq_dispose_mapping() and frees that virtual IRQ number. Now, if another CPU comes along and calls irq_create_mapping(), it is likely to get the virtual IRQ number that was just freed, resulting in the same virtual IRQ number apparently being used for two different hardware interrupts. To fix this race, we just move the call to msi_bitmap_free_hwirqs() to after the call to irq_dispose_mapping(). Since virq_to_hw() doesn't work for the virtual IRQ number after irq_dispose_mapping() has been called, we need to call it before irq_dispose_mapping() and remember the result for the msi_bitmap_free_hwirqs() call. The pattern of calling msi_bitmap_free_hwirqs() before irq_dispose_mapping() appears in 5 places under arch/powerpc, and appears to have originated in commit 05af7bd2 ("[POWERPC] MPIC U3/U4 MSI backend") from 2007. Fixes: 05af7bd2 ("[POWERPC] MPIC U3/U4 MSI backend") Reported-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Eric Whitney authored
commit 94426f4b upstream. In ext4_zero_range(), removing a file's entire block range from the extent status tree removes all records of that file's delalloc extents. The delalloc accounting code uses this information, and its loss can then lead to accounting errors and kernel warnings at writeback time and subsequent file system damage. This is most noticeable on bigalloc file systems where code in ext4_ext_map_blocks() handles cases where delalloc extents share clusters with a newly allocated extent. Because we're not deleting a block range and are correctly updating the status of its associated extent, there is no need to remove anything from the extent status tree. When this patch is combined with an unrelated bug fix for ext4_zero_range(), kernel warnings and e2fsck errors reported during xfstests runs on bigalloc filesystems are greatly reduced without introducing regressions on other xfstests-bld test scenarios. Signed-off-by:
Eric Whitney <enwlinux@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Yann Droneaud authored
commit ebf2d268 upstream. Commit 0a196848 ("perf: Fix arch_perf_out_copy_user default"), changes copy_from_user_nmi() to return the number of remaining bytes so that it behave like copy_from_user(). Unfortunately, when the range is outside of the process memory, the return value is still the number of byte copied, eg. 0, instead of the remaining bytes. As all users of copy_from_user_nmi() were modified as part of commit 0a196848, the function should be fixed to return the total number of bytes if range is not correct. Signed-off-by:
Yann Droneaud <ydroneaud@opteya.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1435001923-30986-1-git-send-email-ydroneaud@opteya.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Yann Droneaud <ydroneaud@opteya.com> Signed-off-by:
-
NeilBrown authored
commit 299b0685 upstream. 'reshape_position' tracks where in the reshape we have reached. 'reshape_safe' tracks where in the reshape we have safely recorded in the metadata. These are compared to determine when to update the metadata. So it is important that reshape_safe is initialised properly. Currently it isn't. When starting a reshape from the beginning it usually has the correct value by luck. But when reducing the number of devices in a RAID10, it has the wrong value and this leads to the metadata not being updated correctly. This can lead to corruption if the reshape is not allowed to complete. This patch is suitable for any -stable kernel which supports RAID10 reshape, which is 3.5 and later. Fixes: 3ea7daa5 ("md/raid10: add reshape support") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
NeilBrown authored
commit ee5d004f upstream. The 'event_work' worker used by dm-raid may still be running when the array is stopped. This can result in an oops. So flush the workqueue on which it is run after detaching and before destroying the device. Reported-by:
Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by:
-
Christoph Hellwig authored
commit 294ab783 upstream. It looks like the Kconfig check that was meant to fix this (commit fe9233fb [SCSI] scsi_dh: fix kconfig related build errors) was actually reversed, but no-one noticed until the new set of patches which separated DM and SCSI_DH). Fixes: fe9233fbSigned-off-by:
Christoph Hellwig <hch@lst.de> Tested-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Daniel Borkmann authored
commit 6bb0fef4 upstream. When netlink mmap on receive side is the consumer of nf queue data, it can happen that in some edge cases, we write skb shared info into the user space mmap buffer: Assume a possible rx ring frame size of only 4096, and the network skb, which is being zero-copied into the netlink skb, contains page frags with an overall skb->len larger than the linear part of the netlink skb. skb_zerocopy(), which is generic and thus not aware of the fact that shared info cannot be accessed for such skbs then tries to write and fill frags, thus leaking kernel data/pointers and in some corner cases possibly writing out of bounds of the mmap area (when filling the last slot in the ring buffer this way). I.e. the ring buffer slot is then of status NL_MMAP_STATUS_VALID, has an advertised length larger than 4096, where the linear part is visible at the slot beginning, and the leaked sizeof(struct skb_shared_info) has been written to the beginning of the next slot (also corrupting the struct nl_mmap_hdr slot header incl. status etc), since skb->end points to skb->data + ring->frame_size - NL_MMAP_HDRLEN. The fix adds and lets __netlink_alloc_skb() take the actual needed linear room for the network skb + meta data into account. It's completely irrelevant for non-mmaped netlink sockets, but in case mmap sockets are used, it can be decided whether the available skb_tailroom() is really large enough for the buffer, or whether it needs to internally fallback to a normal alloc_skb(). >From nf queue side, the information whether the destination port is an mmap RX ring is not really available without extra port-to-socket lookup, thus it can only be determined in lower layers i.e. when __netlink_alloc_skb() is called that checks internally for this. I chose to add the extra ldiff parameter as mmap will then still work: We have data_len and hlen in nfqnl_build_packet_message(), data_len is the full length (capped at queue->copy_range) for skb_zerocopy() and hlen some possible part of data_len that needs to be copied; the rem_len variable indicates the needed remaining linear mmap space. The only other workaround in nf queue internally would be after allocation time by f.e. cap'ing the data_len to the skb_tailroom() iff we deal with an mmap skb, but that would 1) expose the fact that we use a mmap skb to upper layers, and 2) trim the skb where we otherwise could just have moved the full skb into the normal receive queue. After the patch, in my test case the ring slot doesn't fit and therefore shows NL_MMAP_STATUS_COPY, where a full skb carries all the data and thus needs to be picked up via recv(). Fixes: 3ab1f683 ("nfnetlink: add support for memory mapped netlink") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Sergei Shtylyov authored
commit bd1a05ee upstream. I've noticed that fixed_phy_register() ignores its 'irq' parameter instead of passing it to fixed_phy_add(). Luckily, fixed_phy_register() seems to always be called with PHY_POLL for 'irq'... :-) Fixes: a7595121 ("net: phy: extend fixed driver with fixed_phy_register()") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Eric Dumazet authored
commit c8219906 upstream. In commit f341861f ("task_work: add a scheduling point in task_work_run()") I fixed a latency problem adding a cond_resched() call. Later, commit ac3d0da8 added yet another loop to reverse a list, bringing back the latency spike : I've seen in some cases this loop taking 275 ms, if for example a process with 2,000,000 files is killed. We could add yet another cond_resched() in the reverse loop, or we can simply remove the reversal, as I do not think anything would depend on order of task_work_add() submitted works. Fixes: ac3d0da8 ("task_work: Make task_work_add() lockless") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Maciej Żenczykowski <maze@google.com> Acked-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Daniel Borkmann authored
commit e41b0bed upstream. We previously register IPPROTO_ROUTING offload under inet6_add_offload(), but in error path, we try to unregister it with inet_del_offload(). This doesn't seem correct, it should actually be inet6_del_offload(), also ipv6_exthdrs_offload_exit() from that commit seems rather incorrect (it also uses rthdr_offload twice), but it got removed entirely later on. Fixes: 3336288a ("ipv6: Switch to using new offload infrastructure.") Signed-off-by:
-
Jialing Fu authored
commit 71f8a4b8 upstream. The following panic is captured in ker3.14, but the issue still exists in latest kernel. --------------------------------------------------------------------- [ 20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference at virtual address 00000578 ...... [ 20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60 [ 20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60 [ 20.740134] c0 3136 (Compiler) Call trace: [ 20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60 [ 20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54 [ 20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34 [ 20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220 [ 20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264 [ 20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158 [ 20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4 [ 20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0 [ 20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac [ 20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c ---------------------------------------------------------------------- Because in SMP, "mrq" has race condition between below two paths: path1: CPU0: <tasklet context> static void mmc_wait_data_done(struct mmc_request *mrq) { mrq->host->context_info.is_done_rcv = true; // // If CPU0 has just finished "is_done_rcv = true" in path1, and at // this moment, IRQ or ICache line missing happens in CPU0. // What happens in CPU1 (path2)? // // If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode: // path2 would have chance to break from wait_event_interruptible // in mmc_wait_for_data_req_done and continue to run for next // mmc_request (mmc_blk_rw_rq_prep). // // Within mmc_blk_rq_prep, mrq is cleared to 0. // If below line still gets host from "mrq" as the result of // compiler, the panic happens as we traced. wake_up_interruptible(&mrq->host->context_info.wait); } path2: CPU1: <The mmcqd thread runs mmc_queue_thread> static int mmc_wait_for_data_req_done(... { ... while (1) { wait_event_interruptible(context_info->wait, (context_info->is_done_rcv || context_info->is_new_req)); static void mmc_blk_rw_rq_prep(... { ... memset(brq, 0, sizeof(struct mmc_blk_request)); This issue happens very coincidentally; however adding mdelay(1) in mmc_wait_data_done as below could duplicate it easily. static void mmc_wait_data_done(struct mmc_request *mrq) { mrq->host->context_info.is_done_rcv = true; + mdelay(1); wake_up_interruptible(&mrq->host->context_info.wait); } At runtime, IRQ or ICache line missing may just happen at the same place of the mdelay(1). This patch gets the mmc_context_info at the beginning of function, it can avoid this race condition. Signed-off-by:
Jialing Fu <jlfu@marvell.com> Tested-by:
Shawn Lin <shawn.lin@rock-chips.com> Fixes: 2220eedf ("mmc: fix async request mechanism ....") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Yishai Hadas authored
commit 35d4a0b6 upstream. Fixes: 2a72f212 ("IB/uverbs: Remove dev_table") Before this commit there was a device look-up table that was protected by a spin_lock used by ib_uverbs_open and by ib_uverbs_remove_one. When it was dropped and container_of was used instead, it enabled the race with remove_one as dev might be freed just after: dev = container_of(inode->i_cdev, struct ib_uverbs_device, cdev) but before the kref_get. In addition, this buggy patch added some dead code as container_of(x,y,z) can never be NULL and so dev can never be NULL. As a result the comment above ib_uverbs_open saying "the open method will either immediately run -ENXIO" is wrong as it can never happen. The solution follows Jason Gunthorpe suggestion from below URL: https://www.mail-archive.com/linux-rdma@vger.kernel.org/msg25692.html cdev will hold a kref on the parent (the containing structure, ib_uverbs_device) and only when that kref is released it is guaranteed that open will never be called again. In addition, fixes the active count scheme to use an atomic not a kref to prevent WARN_ON as pointed by above comment from Jason. Signed-off-by:
Yishai Hadas <yishaih@mellanox.com> Signed-off-by:
Shachar Raindel <raindel@mellanox.com> Reviewed-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Noa Osherovich authored
commit 5e99b139 upstream. The mlx4 IB driver implementation for ib_query_ah used a wrong offset (28 instead of 29) when link type is Ethernet. Fixed to use the correct one. Fixes: fa417f7b ('IB/mlx4: Add support for IBoE') Signed-off-by:
Shani Michaeli <shanim@mellanox.com> Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
commit 2b135db3 upstream. The pkey mapping for RoCE must remain the default mapping: VFs: virtual index 0 = mapped to real index 0 (0xFFFF) All others indices: mapped to a real pkey index containing an invalid pkey. PF: virtual index i = real index i. Don't allow users to change these mappings using files found in sysfs. Fixes: c1e7e466 ('IB/mlx4: Add iov directory in sysfs under the ib device') Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
-
Jack Morgenstein authored
commit 90c1d8b6 upstream. send_mad_to_wire takes the same spinlock that is taken in the interrupt context. Therefore, it needs irqsave/restore. Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV') Signed-off-by:
-
Axel Lin authored
commit 2c3f4b97 upstream. All the callers assume devm_spear_pcm_platform_register is a devm_ API, so use devm_snd_dmaengine_pcm_register in devm_spear_pcm_platform_register. Fixes: e1771bcf ("ASoC: SPEAr: remove custom DMA alloc compat function") Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Kan Liang authored
commit 601083cf upstream. print_aggr() fails to print per-core/per-socket statistics after commit 582ec082 ("perf stat: Fix per-socket output bug for uncore events") if events have differnt cpus. Because in print_aggr(), aggr_get_id needs index (not cpu id) to find core/pkg id. Also, evsel cpu maps should be used to get aggregated id. Here is an example: Counting events cycles,uncore_imc_0/cas_count_read/. (Uncore event has cpumask 0,18) $ perf stat -e cycles,uncore_imc_0/cas_count_read/ -C0,18 --per-core sleep 2 Without this patch, it failes to get CPU 18 result. Performance counter stats for 'CPU(s) 0,18': S0-C0 1 7526851 cycles S0-C0 1 1.05 MiB uncore_imc_0/cas_count_read/ S1-C0 0 <not counted> cycles S1-C0 0 <not counted> MiB uncore_imc_0/cas_count_read/ With this patch, it can get both CPU0 and CPU18 result. Performance counter stats for 'CPU(s) 0,18': S0-C0 1 6327768 cycles S0-C0 1 0.47 MiB uncore_imc_0/cas_count_read/ S1-C0 1 330228 cycles S1-C0 1 0.29 MiB uncore_imc_0/cas_count_read/ Signed-off-by:
Kan Liang <kan.liang@intel.com> Acked-by:
Jiri Olsa <jolsa@kernel.org> Acked-by:
Stephane Eranian <eranian@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Fixes: 582ec082 ("perf stat: Fix per-socket output bug for uncore events") Link: http://lkml.kernel.org/r/1435820925-51091-1-git-send-email-kan.liang@intel.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Jisheng Zhang authored
commit 0dafa60e upstream. commit bb8175a8 ("mmc: sdhci: clarify DDR timing mode between SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be distinguished from SD-UHS, but it missed setting driver type for MMC_DDR52 timing mode. So sometimes we get the following error on Marvell BG2Q DMP board: [ 1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00 [ 1.569314] mmcblk0: retrying using single block read [ 1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0 [ 1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2 [ 1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0 [ 1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3 This patches fixes this by adding the missing driver type setting. Fixes: bb8175a8 ("mmc: sdhci: clarify DDR timing mode ...") Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
-
Michal Kazior authored
commit 5e55e3cb upstream. The function returns 1 when DMA mapping fails. The driver would return bogus values and could possibly confuse itself if DMA failed. Fixes: 767d34fc ("ath10k: remove DMA mapping wrappers") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Antoine Ténart authored
commit bc3e00f0 upstream. When keeping the configuration set by the bootloader (by using the marvell,nand-keep-config property), the pxa3xx_nand_detect_config() function is called and set the chunk size to 512 as a default value if NDCR_PAGE_SZ is not set. In the other case, when not keeping the bootloader configuration, no chunk size is set. Fix this by adding a default chunk size of 512. Fixes: 70ed8523 ("mtd: nand: pxa3xx: Introduce multiple page I/O support") Signed-off-by:
Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by:
Robert Jarzmik <robert.jarzmik@free> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Michael Ellerman authored
commit 74b5037b upstream. The powerpc kernel can be built to have either a 4K PAGE_SIZE or a 64K PAGE_SIZE. However when built with a 4K PAGE_SIZE there is an additional config option which can be enabled, PPC_HAS_HASH_64K, which means the kernel also knows how to hash a 64K page even though the base PAGE_SIZE is 4K. This is used in one obscure configuration, to support 64K pages for SPU local store on the Cell processor when the rest of the kernel is using 4K pages. In this configuration, pte_pagesize_index() is defined to just pass through its arguments to get_slice_psize(). However pte_pagesize_index() is called for both user and kernel addresses, whereas get_slice_psize() only knows how to handle user addresses. This has been broken forever, however until recently it happened to work. That was because in get_slice_psize() the large kernel address would cause the right shift of the slice mask to return zero. However in commit 7aa0727f ("powerpc/mm: Increase the slice range to 64TB"), the get_slice_psize() code was changed so that instead of a right shift we do an array lookup based on the address. When passed a kernel address this means we index way off the end of the slice array and return random junk. That is only fatal if we happen to hit something non-zero, but when we do return a non-zero value we confuse the MMU code and eventually cause a check stop. This fix is ugly, but simple. When we're called for a kernel address we return 4K, which is always correct in this configuration, otherwise we use the slice mask. Fixes: 7aa0727f ("powerpc/mm: Increase the slice range to 64TB") Reported-by:
Cyril Bur <cyrilbur@gmail.com> Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
-
Jesse Brandeburg authored
commit fbaff3ef upstream. Sparse builds have been warning for a really long time now that etherdevice.h has a conversion that is unsafe. include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer This code change fixes the issue and generates the exact same assembly before/after (checked on x86_64) Fixes: 2c722fe1 (etherdevice: Optimize a few is_<foo>_ether_addr functions) Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Joe Perches <joe@perches.com> Signed-off-by:
-
Linus Lüssing authored
commit 53cf037b upstream. The two commits noted below added calls to ip_hdr() and ipv6_hdr(). They need a correctly set skb network header. Unfortunately we cannot rely on the device drivers to set it for us. Therefore setting it in the beginning of the according ndo_start_xmit handler. Fixes: 1d8ab8d3 ("batman-adv: Modified forwarding behaviour for multicast packets") Fixes: ab49886e ("batman-adv: Add IPv4 link-local/IPv6-ll-all-nodes multicast support") Signed-off-by:
Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
Antonio Quartulli <antonio@meshcoding.com> Signed-off-by:
-
Linus Lüssing authored
commit 8a4023c5 upstream. So far the mcast tvlv handler did not anticipate the processing of multiple incoming OGMs from the same originator at the same time. This can lead to various issues: * Broken refcounting: For instance two mcast handlers might both assume that an originator just got multicast capabilities and will together wrongly decrease mcast.num_disabled by two, potentially leading to an integer underflow. * Potential kernel panic on hlist_del_rcu(): Two mcast handlers might one after another try to do an hlist_del_rcu(&orig->mcast_want_all_*_node). The second one will cause memory corruption / crashes. (Reported by: Sven Eckelmann <sven@narfation.org>) Right in the beginning the code path makes assumptions about the current multicast related state of an originator and bases all updates on that. The easiest and least error prune way to fix the issues in this case is to serialize multiple mcast handler invocations with a spinlock. Fixes: 60432d75 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by:
-
Linus Lüssing authored
commit 9c936e3f upstream. Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One OGM handler might undo the set/clear of a specific bit from another handler run in between. Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions. Fixes: 60432d75 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by:
-
Linus Lüssing authored
commit e8829f00 upstream. A miscounting of nodes having multicast optimizations enabled can lead to multicast packet loss in the following scenario: If the first OGM a node receives from another one has no multicast optimizations support (no multicast tvlv) then we are missing to increase the counter. This potentially leads to the wrong assumption that we could safely use multicast optimizations. Fixings this by increasing the counter if the initial OGM has the multicast TVLV unset, too. Introduced by 60432d75 ("batman-adv: Announce new capability via multicast TVLV") Reported-by:
Tobias Hachmer <tobias@hachmer.de> Signed-off-by:
-
Linus Lüssing authored
commit a5164886 upstream. When purging an orig_node we should only decrease counter tracking the number of nodes without multicast optimizations support if it was increased through this orig_node before. A not yet quite initialized orig_node (meaning it did not have its turn in the mcast-tvlv handler so far) which gets purged would not adhere to this and will lead to a counter imbalance. Fixing this by adding a check whether the orig_node is mcast-initalized before decreasing the counter in the mcast-orig_node-purging routine. Introduced by 60432d75 ("batman-adv: Announce new capability via multicast TVLV") Reported-by:
-
Linus Lüssing authored
commit ac4eebd4 upstream. Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One OGM handler might undo the set/clear of a specific bit from another handler run in between. Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions. Fixes: e17931d1 ("batman-adv: introduce capability initialization bitfield") Signed-off-by:
-
Linus Lüssing authored
commit 4635469f upstream. Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One OGM handler might undo the set/clear of a specific bit from another handler run in between. Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions. Fixes: 3f4841ff ("batman-adv: tvlv - add network coding container") Signed-off-by:
-
Linus Lüssing authored
commit 65d7d460 upstream. Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One OGM handler might undo the set/clear of a specific bit from another handler run in between. Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions. Fixes: 17cf0ea4 ("batman-adv: tvlv - add distributed arp table container") Signed-off-by:
-
Arnaldo Carvalho de Melo authored
commit e8e6d37e upstream. When we introduce a new sort key, we need to update the hists__calc_col_len() function accordingly, otherwise the width will be limited to strlen(header). We can't update it when obtaining a line value for a column (for instance, in sort__srcline_cmp()), because we reset it all when doing a resort (see hists__output_recalc_col_len()), so we need to, from what is in the hist_entry fields, set each of the column widths. Cc: Namhyung Kim <namhyung@kernel.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: Jiri Olsa <jolsa@kernel.org> Fixes: 409a8be6 ("perf tools: Add sort by src line/number") Link: http://lkml.kernel.org/n/tip-jgbe0yx8v1gs89cslr93pvz2@git.kernel.orgSigned-off-by:
-
Paul Bolle authored
commit fe2b5921 upstream. wf_unregister_client() increments the client count when a client unregisters. That is obviously incorrect. Decrement that client count instead. Fixes: 75722d39 ("[PATCH] ppc64: Thermal control for SMU based machines") Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
Dan Carpenter authored
commit 5feb5d20 upstream. There is an "&&" vs "||" typo here so this loops 3000 times or if we get unlucky it could loop forever. Fixes: ceaa0a6e ('usb: gadget: m66592-udc: add support for TEST_MODE') Signed-off-by:
Felipe Balbi <balbi@ti.com> [ luis: backported to 3.16: - file rename: drivers/usb/gadget/udc/m66592-udc.c -> drivers/usb/gadget/m66592-udc.c ] Signed-off-by:
-
Dan Carpenter authored
commit 3294bee8 upstream. The ">" should be ">=" or we end up reading beyond the end of the array. Fixes: 6e973d2c ('clk: vexpress: Add separate SP810 driver') Signed-off-by:
Pawel Moll <pawel.moll@arm.com> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Thomas Huth authored
commit 1c2cb594 upstream. The EPOW interrupt handler uses rtas_get_sensor(), which in turn uses rtas_busy_delay() to wait for RTAS becoming ready in case it is necessary. But rtas_busy_delay() is annotated with might_sleep() and thus may not be used by interrupts handlers like the EPOW handler! This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is enabled: BUG: sleeping function called from invalid context at arch/powerpc/kernel/rtas.c:496 in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1 CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.2.0-rc2-thuth #6 Call Trace: [c00000007ffe7b90] [c000000000807670] dump_stack+0xa0/0xdc (unreliable) [c00000007ffe7bc0] [c0000000000e1f14] ___might_sleep+0x134/0x180 [c00000007ffe7c20] [c00000000002aec0] rtas_busy_delay+0x30/0xd0 [c00000007ffe7c50] [c00000000002bde4] rtas_get_sensor+0x74/0xe0 [c00000007ffe7ce0] [c000000000083264] ras_epow_interrupt+0x44/0x450 [c00000007ffe7d90] [c000000000120260] handle_irq_event_percpu+0xa0/0x300 [c00000007ffe7e70] [c000000000120524] handle_irq_event+0x64/0xc0 [c00000007ffe7eb0] [c000000000124dbc] handle_fasteoi_irq+0xec/0x260 [c00000007ffe7ef0] [c00000000011f4f0] generic_handle_irq+0x50/0x80 [c00000007ffe7f20] [c000000000010f3c] __do_irq+0x8c/0x200 [c00000007ffe7f90] [c0000000000236cc] call_do_irq+0x14/0x24 [c00000007e6f39e0] [c000000000011144] do_IRQ+0x94/0x110 [c00000007e6f3a30] [c000000000002594] hardware_interrupt_common+0x114/0x180 Fix this issue by introducing a new rtas_get_sensor_fast() function that does not use rtas_busy_delay() - and thus can only be used for sensors that do not cause a BUSY condition - known as "fast" sensors. The EPOW sensor is defined to be "fast" in sPAPR - mpe. Fixes: 587f83e8 ("powerpc/pseries: Use rtas_get_sensor in RAS code") Signed-off-by:
Thomas Huth <thuth@redhat.com> Reviewed-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
-
Florian Fainelli authored
commit 978ffac4 upstream. bcmgenet_open()'s error path call free_irq() with a dev_id argument different from the one we used to call request_irq() with, this will make us trip over the warning in kernel/irq/manage.c:__free_irq() Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
