P1010rdb-pa and p1010rdb-pb have different mtd of nand.
So update dts to adapt to both p1010rdb-pa and p1010rdb-pb.

Move the nand-mtd from p1010rdb.dtsi to p1010rdb-pa*.dts.
Remove nand-mtd for p1010rdb-pb, whick will use mtdparts
from u-boot instead of nand-mtd in device tree.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

P1010rdb-pa and p1010rdb-pb have different phy interrupts.
So update dts to adapt to both p1010rdb-pa and p1010rdb-pb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The e500 SPE floating-point emulation code is called from
SPEFloatingPointException and SPEFloatingPointRoundException in
arch/powerpc/kernel/traps.c.  Those functions have support for
generating SIGFPE, but do_spe_mathemu and speround_handler don't
generate a return value to indicate that this should be done.  Such a
return value should depend on whether an exception is raised that has
been set via prctl to generate SIGFPE.  This patch adds the relevant
logic in these functions so that SIGFPE is generated as expected by
the glibc testsuite.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The e500 SPE floating-point emulation code has several problems in how
it handles conversions to integer and fixed-point fractional types.

There are the following 20 relevant instructions.  These can convert
to signed or unsigned 32-bit integers, either rounding towards zero
(as correct for C casts from floating-point to integer) or according
to the current rounding mode, or to signed or unsigned 32-bit
fixed-point values (values in the range [-1, 1) or [0, 1)).  For
conversion from double precision there are also instructions to
convert to 64-bit integers, rounding towards zero, although as far as
I know those instructions are completely theoretical (they are only
defined for implementations that support both SPE and classic 64-bit,
and I'm not aware of any such hardware even though the architecture
definition permits that combination).

#define EFSCTUI		0x2d4
#define EFSCTSI		0x2d5
#define EFSCTUF		0x2d6
#define EFSCTSF		0x2d7
#define EFSCTUIZ	0x2d8
#define EFSCTSIZ	0x2da

#define EVFSCTUI	0x294
#define EVFSCTSI	0x295
#define EVFSCTUF	0x296
#define EVFSCTSF	0x297
#define EVFSCTUIZ	0x298
#define EVFSCTSIZ	0x29a

#define EFDCTUIDZ	0x2ea
#define EFDCTSIDZ	0x2eb

#define EFDCTUI		0x2f4
#define EFDCTSI		0x2f5
#define EFDCTUF		0x2f6
#define EFDCTSF		0x2f7
#define EFDCTUIZ	0x2f8
#define EFDCTSIZ	0x2fa

The emulation code, for the instructions that come in variants
rounding either towards zero or according to the current rounding
direction, uses "if (func & 0x4)" as a condition for using _FP_ROUND
(otherwise _FP_ROUND_ZERO is used).  The condition is correct, but the
code it controls isn't.  Whether _FP_ROUND or _FP_ROUND_ZERO is used
makes no difference, as the effect of those soft-fp macros is to round
an intermediate floating-point result using the low three bits (the
last one sticky) of the working format.  As these operations are
dealing with a freshly unpacked floating-point input, those low bits
are zero and no rounding occurs.  The emulation code then uses the
FP_TO_INT_* macros for the actual integer conversion, with the effect
of always rounding towards zero; for rounding according to the current
rounding direction, it should be using FP_TO_INT_ROUND_*.

The instructions in question have semantics defined (in the Power ISA
documents) for out-of-range values and NaNs: out-of-range values
saturate and NaNs are converted to zero.  The emulation does nothing
to follow those semantics for NaNs (the soft-fp handling is to treat
them as infinities), and messes up the saturation semantics.  For
single-precision conversion to integers, (((func & 0x3) != 0) || SB_s)
is the condition used for doing a signed conversion.  The first part
is correct, but the second isn't: negative numbers should result in
saturation to 0 when converted to unsigned.  Double-precision
conversion to 64-bit integers correctly uses ((func & 0x1) == 0).
Double-precision conversion to 32-bit integers uses (((func & 0x3) !=
0) || DB_s), with correct first part and incorrect second part.  And
vector float conversion to integers uses (((func & 0x3) != 0) ||
SB0_s) (and similar for the other vector element), where the sign bit
check is again wrong.

The incorrect handling of negative numbers converted to unsigned was
introduced in commit afc0a07d.  The
rationale given there was a C testcase with cast from float to
unsigned int.  Conversion of out-of-range floating-point numbers to
integer types in C is undefined behavior in the base standard, defined
in Annex F to produce an unspecified value.  That is, the C testcase
used to justify that patch is incorrect - there is no ISO C
requirement for a particular value resulting from this conversion -
and in any case, the correct semantics for such emulation are the
semantics for the instruction (unsigned saturation, which is what it
does in hardware when the emulation is disabled).

The conversion to fixed-point values has its own problems.  That code
doesn't try to do a full emulation; it relies on the trap handler only
being called for arguments that are infinities, NaNs, subnormal or out
of range.  That's fine, but the logic ((vb.wp[1] >> 23) == 0xff &&
((vb.wp[1] & 0x7fffff) > 0)) for NaN detection won't detect negative
NaNs as being NaNs (the same applies for the double-precision case),
and subnormals are mapped to 0 rather than respecting the rounding
mode; the code should also explicitly raise the "invalid" exception.
The code for vectors works by executing the scalar float instruction
with the trapping disabled, meaning at least subnormals won't be
handled correctly.

As well as all those problems in the main emulation code, the rounding
handler - used to emulate rounding upward and downward when not
supported in hardware and when no higher priority exception occurred -
has its own problems.

* It gets called in some cases even for the instructions rounding to
  zero, and then acts according to the current rounding mode when it
  should just leave alone the truncated result provided by hardware.

* It presumes that the result is a single-precision, double-precision
  or single-precision vector as appropriate for the instruction type,
  determines the sign of the result accordingly, and then adjusts the
  result based on that sign and the rounding mode.

  - In the single-precision cases at least the sign determination for
    an integer result is the same as for a floating-point result; in
    the double-precision case, converted to 32-bit integer or fixed
    point, the sign of a double-precision value is in the high part of
    the register but it's the low part of the register that has the
    result of the conversion.

  - If the result is unsigned fixed-point, its sign may be wrongly
    determined as negative (does not actually cause problems, because
    inexact unsigned fixed-point results with the high bit set can
    only appear when converting from double, in which case the sign
    determination is instead wrongly using the high part of the
    register).

  - If the sign of the result is correctly determined as negative, any
    adjustment required to change the truncated result to one correct
    for the rounding mode should be in the opposite direction for
    two's-complement integers as for sign-magnitude floating-point
    values.

  - And if the integer result is zero, the correct sign can only be
    determined by examining the original operand, and not at all (as
    far as I can tell) if the operand and result are the same
    register.

This patch fixes all these problems (as far as possible, given the
inability to determine the correct sign in the rounding handler when
the truncated result is 0, the conversion is to a signed type and the
truncated result has overwritten the original operand).  Conversion to
fixed-point now uses full emulation, and does not use "asm" in the
vector case; the semantics are exactly those of converting to integer
according to the current rounding direction, once the exponent has
been adjusted, so the code makes such an adjustment then uses the
FP_TO_INT_ROUND macros.

The testcase I used for verifying that the instructions (other than
the theoretical conversions to 64-bit integers) produce the correct
results is at <http://lkml.org/lkml/2013/10/8/708>.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

On overflow, the math-emu macro _FP_TO_INT_ROUND tries to saturate its
result (subject to the value of rsigned specifying the desired
overflow semantics).  However, if the rounding step has the effect of
increasing the exponent so as to cause overflow (if the rounded result
is 1 larger than the largest positive value with the given number of
bits, allowing for signedness), the overflow does not get detected,
meaning that for unsigned results 0 is produced instead of the maximum
unsigned integer with the give number of bits, without an exception
being raised for overflow, and that for signed results the minimum
(negative) value is produced instead of the maximum (positive) value,
again without an exception.  This patch makes the code check for
rounding increasing the exponent and adjusts the exponent value as
needed for the overflow check.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The math-emu macros _FP_TO_INT and _FP_TO_INT_ROUND are supposed to
saturate their results for out-of-range arguments, except in the case
rsigned == 2 (when instead the low bits of the result are taken).
However, in the case rsigned == 0 (converting to unsigned integers),
they mistakenly produce 0 for positive results and the maximum
unsigned integer for negative results, the opposite of correct
unsigned saturation.  This patch fixes the logic.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The e500 SPE floating-point emulation code for the rounding modes
rounding to positive or negative infinity (which may not be
implemented in hardware) tries to avoid emulating rounding if the
result was inexact.  However, it tests inexactness using the sticky
bit with the cumulative result of previous operations, rather than
with the non-sticky bits relating to the operation that generated the
interrupt.  Furthermore, when a vector operation generates the
interrupt, it's possible that only one of the low and high parts is
inexact, and so only that part should have rounding emulated.  This
results in incorrect rounding of exact results in these modes when the
sticky bit is set from a previous operation.

(I'm not sure why the rounding interrupts are generated at all when
the result is exact, but empirically the hardware does generate them.)

This patch checks for inexactness using the correct bits of SPEFSCR,
and ensures that rounding only occurs when the relevant part of the
result was actually inexact.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

The e500 SPE floating-point emulation code clears existing exceptions
(__FPU_FPSCR &= ~FP_EX_MASK;) before ORing in the exceptions from the
emulated operation.  However, these exception bits are the "sticky",
cumulative exception bits, and should only be cleared by the user
program setting SPEFSCR, not implicitly by any floating-point
instruction (whether executed purely by the hardware or emulated).
The spurious clearing of these bits shows up as missing exceptions in
glibc testing.

Fixing this, however, is not as simple as just not clearing the bits,
because while the bits may be from previous floating-point operations
(in which case they should not be cleared), the processor can also set
the sticky bits itself before the interrupt for an exception occurs,
and this can happen in cases when IEEE 754 semantics are that the
sticky bit should not be set.  Specifically, the "invalid" sticky bit
is set in various cases with non-finite operands, where IEEE 754
semantics do not involve raising such an exception, and the
"underflow" sticky bit is set in cases of exact underflow, whereas
IEEE 754 semantics are that this flag is set only for inexact
underflow.  Thus, for correct emulation the kernel needs to know the
setting of these two sticky bits before the instruction being
emulated.

When a floating-point operation raises an exception, the kernel can
note the state of the sticky bits immediately afterwards.  Some
<fenv.h> functions that affect the state of these bits, such as
fesetenv and feholdexcept, need to use prctl with PR_GET_FPEXC and
PR_SET_FPEXC anyway, and so it is natural to record the state of those
bits during that call into the kernel and so avoid any need for a
separate call into the kernel to inform it of a change to those bits.
Thus, the interface I chose to use (in this patch and the glibc port)
is that one of those prctl calls must be made after any userspace
change to those sticky bits, other than through a floating-point
operation that traps into the kernel anyway.  feclearexcept and
fesetexceptflag duly make those calls, which would not be required
were it not for this issue.

The previous EGLIBC port, and the uClibc code copied from it, is
fundamentally broken as regards any use of prctl for floating-point
exceptions because it didn't use the PR_FP_EXC_SW_ENABLE bit in its
prctl calls (and did various worse things, such as passing a pointer
when prctl expected an integer).  If you avoid anything where prctl is
used, the clearing of sticky bits still means it will never give
anything approximating correct exception semantics with existing
kernels.  I don't believe the patch makes things any worse for
existing code that doesn't try to inform the kernel of changes to
sticky bits - such code may get incorrect exceptions in some cases,
but it would have done so anyway in other cases.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

LRAT (Logical to Real Address Translation) present in MMU v2 provides hardware
translation from a logical page number (LPN) to a real page number (RPN) when
tlbwe is executed by a guest or when a page table translation occurs from a
guest virtual address.

Add LRAT error exception handler to Booke3E 64-bit kernel and the basic KVM
handler to avoid build breakage. This is a prerequisite for KVM LRAT support
that will follow.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Merge a pile of fixes that went into the "merge" branch (3.13-rc's) such
as Anton Little Endian fixes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The SLB save area is shared with the hypervisor and is defined
as big endian, so we need to byte swap on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Anatolij writes:

Please pull two DTS fixes for MPC5125 tower board. Without
them the v3.13-rcX kernels do not boot.

This patch updates the generic iommu backend code to use the
it_page_shift field to determine the iommu page size instead of
using hardcoded values.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds a it_page_shift field to struct iommu_table and
initiliases it to 4K for all platforms.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The powerpc iommu uses a hardcoded page size of 4K. This patch changes
the name of the IOMMU_PAGE_* macros to reflect the hardcoded values. A
future patch will use the existing names to support dynamic page
sizes.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This removes the REDBOOT Kconfig parameter,
which was no longer used anywhere in the source code
and Makefiles.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

With recent machine check patch series changes, The exception vectors
starting from 0x4300 are now overflowing with allyesconfig. Fix that by
moving machine_check_common and machine_check_handle_early code out of
that region to make enough room for exception vector area.

Fixes this build error reportes by Stephen:

arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:958: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:959: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:983: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:984: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1003: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1013: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1014: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1015: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1016: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1017: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1018: Error: attempt to move .org backwards

[Moved the code further down as it introduced link errors due to too long
 relative branches to the masked interrupts handlers from the exception
 prologs. Also removed the useless feature section --BenH
]
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 5c0484e2 ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.

This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.

Fix is to add explicit alignment instead of relying on good luck. :)

[ It appears that there is a different issue with PA Semi systems
  however this fix is definitely correct so applying anyway -- BenH
]

Fixes: 5c0484e2 ('powerpc: Endian safe trampoline')
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.

This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data.  Take care to inform OPAL of
the correct size for the buffer.

[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations.  However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.

This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.

[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel.  If it's not valid, we die but
with a nice oops message.

Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative.  Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.

This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE.  With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.

Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

At the moment the USB controller's pin muxing is not setup
correctly and causes a kernel panic upon system startup, so
disable the USB1 device tree node in the MPC5125 tower board
dts file.

The USB controller is connected to an USB3320 ULPI transceiver
and the device tree should receive an update to reflect correct
dependencies and required initialization data before the USB1
node can get re-enabled.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

the 'soc' node in the MPC5125 "tower" board .dts has an '#interrupt-cells'
property although this node is not an interrupt controller

remove this erroneously placed property because starting with v3.13-rc1
lookup and resolution of 'interrupts' specs for peripherals gets misled
(tries to use the 'soc' as the interrupt parent which fails), emits
'no irq domain found' WARN() messages and breaks the boot process

[ best viewed with 'git diff -U5' to have DT node names in the context ]

Cc: Anatolij Gustschin <agust@denx.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

We are passing pointers to the firmware for reads, we need to properly
convert the result as OPAL is always BE.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

opal_xscom_read uses a pointer to return the data so we need
to byteswap it on LE builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

A couple more device tree properties that need byte swapping.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The MSI code is miscalculating quotas in little endian mode.
Add required byteswaps to fix this.

Before we claimed a quota of 65536, after the patch we
see the correct value of 256.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We need to byteswap ibm,pcie-link-speed-stats.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The NVRAM code has a number of endian issues. I noticed a very
confused error log count:

RTAS: 100663330 -------- RTAS event begin --------

100663330 == 0x06000022. 0x6 LE error logs and 0x22 BE error logs.

The pstore code has similar issues - if we write an oops in one
endian and attempt to read it in another we get junk.

Make both of these formats big endian, and byteswap as required.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Some obvious issues:

cat /proc/ppc64/lparcfg
...
partition_id=16777216
...
partition_potential_processors=268435456
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

cpu_to_core_id() is missing a byteswap:

cat /sys/devices/system/cpu/cpu63/topology/core_id
201326592
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

During on LE boot we see:

    Partition configured for 1073741824 cpus, operating system maximum is 2048.

Clearly missing a byteswap here.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

There is a bug in using ptrace to access FPRs via PTRACE_PEEKUSR /
PTRACE_POKEUSR. In effect, trying to access any of the FPRs always
really accesses FPR0, which does seriously break debugging :-)

The problem seems to have been introduced by commit 3ad26e5c
(Merge branch 'for-kvm' into next).

[ It is indeed a merge conflict between Paul's FPU/VSX state rework
and my LE patches - Anton ]
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The current logic sets the kdump base to min of 2G or ppc64_rma_size/2.
On PowerNV kernel the first memory block 'memory@0' can be very large,
equal to the DIMM size with ppc64_rma_size value capped to 1G. Hence on
PowerNV, kdump base is set to 512M resulting kdump to fail while allocating
paca array. This is because, paca need its memory from RMA region capped
at 256M (see allocate_pacas()).

This patch lowers the kdump base cap to 128M so that kdump kernel can
successfully get memory below 256M for paca allocation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

I have recently found out that no iommu_groups could be found under
/sys/ on a P8. That prevents PCI passthrough from working.

During my investigation, I found out there seems to be a missing
iommu_register_group for PHB3. The following patch seems to fix the
problem. After applying it, I see iommu_groups under
/sys/kernel/iommu_groups/, and can also bind vfio-pci to an adapter,
which gives me a device at /dev/vfio/.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The bestcomm driver has been moved to drivers/dma, so to select
this driver by default additionally CONFIG_DMADEVICES has to be
enabled. Currently it is not enabled in the config despite existing
CONFIG_PPC_BESTCOMM=y in the config files. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

At least some distros expect it these days; turn it on. Also, random
churn from doing a savedefconfig for the first time in a year or so.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>