- 12 Feb, 2015 40 commits
-
-
Ebru Akagunduz authored
This patch aims to improve THP collapse rates, by allowing THP collapse in the presence of read-only ptes, like those left in place by do_swap_page after a read fault. Currently THP can collapse 4kB pages into a THP when there are up to khugepaged_max_ptes_none pte_none ptes in a 2MB range. This patch applies the same limit for read-only ptes. The patch was tested with a test program that allocates 800MB of memory, writes to it, and then sleeps. I force the system to swap out all but 190MB of the program by touching other memory. Afterwards, the test program does a mix of reads and writes to its memory, and the memory gets swapped back in. Without the patch, only the memory that did not get swapped out remained in THPs, which corresponds to 24% of the memory of the program. The percentage did not increase over time. With this patch, after 5 minutes of waiting khugepaged had collapsed 50% of the program's memory back into THPs. Test results: With the patch: After swapped out: cat /proc/pid/smaps: Anonymous: 100464 kB AnonHugePages: 100352 kB Swap: 699540 kB Fraction: 99,88 cat /proc/meminfo: AnonPages: 1754448 kB AnonHugePages: 1716224 kB Fraction: 97,82 After swapped in: In a few seconds: cat /proc/pid/smaps: Anonymous: 800004 kB AnonHugePages: 145408 kB Swap: 0 kB Fraction: 18,17 cat /proc/meminfo: AnonPages: 2455016 kB AnonHugePages: 1761280 kB Fraction: 71,74 In 5 minutes: cat /proc/pid/smaps Anonymous: 800004 kB AnonHugePages: 407552 kB Swap: 0 kB Fraction: 50,94 cat /proc/meminfo: AnonPages: 2456872 kB AnonHugePages: 2023424 kB Fraction: 82,35 Without the patch: After swapped out: cat /proc/pid/smaps: Anonymous: 190660 kB AnonHugePages: 190464 kB Swap: 609344 kB Fraction: 99,89 cat /proc/meminfo: AnonPages: 1740456 kB AnonHugePages: 1667072 kB Fraction: 95,78 After swapped in: cat /proc/pid/smaps: Anonymous: 800004 kB AnonHugePages: 190464 kB Swap: 0 kB Fraction: 23,80 cat /proc/meminfo: AnonPages: 2350032 kB AnonHugePages: 1667072 kB Fraction: 70,93 I waited 10 minutes the fractions did not change without the patch. Signed-off-by:
Ebru Akagunduz <ebru.akagunduz@gmail.com> Reviewed-by:
Rik van Riel <riel@redhat.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Acked-by:
Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Acked-by:
Andrea Arcangeli <aarcange@redhat.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Michal Hocko authored
Vinayak Menon has reported that an excessive number of tasks was throttled in the direct reclaim inside too_many_isolated() because NR_ISOLATED_FILE was relatively high compared to NR_INACTIVE_FILE. However it turned out that the real number of NR_ISOLATED_FILE was 0 and the per-cpu vm_stat_diff wasn't transferred into the global counter. vmstat_work which is responsible for the sync is defined as deferrable delayed work which means that the defined timeout doesn't wake up an idle CPU. A CPU might stay in an idle state for a long time and general effort is to keep such a CPU in this state as long as possible which might lead to all sorts of troubles for vmstat consumers as can be seen with the excessive direct reclaim throttling. This patch basically reverts 39bf6270 ("VM statistics: Make timer deferrable") but it shouldn't cause any problems for idle CPUs because only CPUs with an active per-cpu drift are woken up since 7cc36bbd ("vmstat: on-demand vmstat workers v8") and CPUs which are idle for a longer time shouldn't have per-cpu drift. Fixes: 39bf6270 (VM statistics: Make timer deferrable) Signed-off-by:
Michal Hocko <mhocko@suse.cz> Reported-by:
Vinayak Menon <vinmenon@codeaurora.org> Acked-by:
Christoph Lameter <cl@linux.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov@parallels.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by:
-
Vlastimil Babka authored
When allocation falls back to stealing free pages of another migratetype, it can decide to steal extra pages, or even the whole pageblock in order to reduce fragmentation, which could happen if further allocation fallbacks pick a different pageblock. In try_to_steal_freepages(), one of the situations where extra pages are stolen happens when we are trying to allocate a MIGRATE_RECLAIMABLE page. However, MIGRATE_UNMOVABLE allocations are not treated the same way, although spreading such allocation over multiple fallback pageblocks is arguably even worse than it is for RECLAIMABLE allocations. To minimize fragmentation, we should minimize the number of such fallbacks, and thus steal as much as is possible from each fallback pageblock. Note that in theory this might put more pressure on movable pageblocks and cause movable allocations to steal back from unmovable pageblocks. However, movable allocations are not as aggressive with stealing, and do not cause permanent fragmentation, so the tradeoff is reasonable, and evaluation seems to support the change. This patch thus adds a check for MIGRATE_UNMOVABLE to the decision to steal extra free pages. When evaluating with stress-highalloc from mmtests, this has reduced the number of MIGRATE_UNMOVABLE fallbacks to roughly 1/6. The number of these fallbacks stealing from MIGRATE_MOVABLE block is reduced to 1/3. There was no observation of growing number of unmovable pageblocks over time, and also not of increased movable allocation fallbacks. Signed-off-by:
Mel Gorman <mgorman@suse.de> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Minchan Kim <minchan@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by:
-
Vlastimil Babka authored
When allocation falls back to another migratetype, it will steal a page with highest available order, and (depending on this order and desired migratetype), it might also steal the rest of free pages from the same pageblock. Given the preference of highest available order, it is likely that it will be higher than the desired order, and result in the stolen buddy page being split. The remaining pages after split are currently stolen only when the rest of the free pages are stolen. This can however lead to situations where for MOVABLE allocations we split e.g. order-4 fallback UNMOVABLE page, but steal only order-0 page. Then on the next MOVABLE allocation (which may be batched to fill the pcplists) we split another order-3 or higher page, etc. By stealing all pages that we have split, we can avoid further stealing. This patch therefore adjusts the page stealing so that buddy pages created by split are always stolen. This has effect only on MOVABLE allocations, as RECLAIMABLE and UNMOVABLE allocations already always do that in addition to stealing the rest of free pages from the pageblock. The change also allows to simplify try_to_steal_freepages() and factor out CMA handling. According to Mel, it has been intended since the beginning that buddy pages after split would be stolen always, but it doesn't seem like it was ever the case until commit 47118af0 ("mm: mmzone: MIGRATE_CMA migration type added"). The commit has unintentionally introduced this behavior, but was reverted by commit 0cbef29a ("mm: __rmqueue_fallback() should respect pageblock type"). Neither included evaluation. My evaluation with stress-highalloc from mmtests shows about 2.5x reduction of page stealing events for MOVABLE allocations, without affecting the page stealing events for other allocation migratetypes. Signed-off-by:
Minchan Kim <minchan@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by:
-
Vlastimil Babka authored
When studying page stealing, I noticed some weird looking decisions in try_to_steal_freepages(). The first I assume is a bug (Patch 1), the following two patches were driven by evaluation. Testing was done with stress-highalloc of mmtests, using the mm_page_alloc_extfrag tracepoint and postprocessing to get counts of how often page stealing occurs for individual migratetypes, and what migratetypes are used for fallbacks. Arguably, the worst case of page stealing is when UNMOVABLE allocation steals from MOVABLE pageblock. RECLAIMABLE allocation stealing from MOVABLE allocation is also not ideal, so the goal is to minimize these two cases. The evaluation of v2 wasn't always clear win and Joonsoo questioned the results. Here I used different baseline which includes RFC compaction improvements from [1]. I found that the compaction improvements reduce variability of stress-highalloc, so there's less noise in the data. First, let's look at stress-highalloc configured to do sync compaction, and how these patches reduce page stealing events during the test. First column is after fresh reboot, other two are reiterations of test without reboot. That was all accumulater over 5 re-iterations (so the benchmark was run 5x3 times with 5 fresh restarts). Baseline: 3.19-rc4 3.19-rc4 3.19-rc4 5-nothp-1 5-nothp-2 5-nothp-3 Page alloc extfrag event 10264225 8702233 10244125 Extfrag fragmenting 10263271 8701552 10243473 Extfrag fragmenting for unmovable 13595 17616 15960 Extfrag fragmenting unmovable placed with movable 7989 12193 8447 Extfrag fragmenting for reclaimable 658 1840 1817 Extfrag fragmenting reclaimable placed with movable 558 1677 1679 Extfrag fragmenting for movable 10249018 8682096 10225696 With Patch 1: 3.19-rc4 3.19-rc4 3.19-rc4 6-nothp-1 6-nothp-2 6-nothp-3 Page alloc extfrag event 11834954 9877523 9774860 Extfrag fragmenting 11833993 9876880 9774245 Extfrag fragmenting for unmovable 7342 16129 11712 Extfrag fragmenting unmovable placed with movable 4191 10547 6270 Extfrag fragmenting for reclaimable 373 1130 923 Extfrag fragmenting reclaimable placed with movable 302 906 738 Extfrag fragmenting for movable 11826278 9859621 9761610 With Patch 2: 3.19-rc4 3.19-rc4 3.19-rc4 7-nothp-1 7-nothp-2 7-nothp-3 Page alloc extfrag event 4725990 3668793 3807436 Extfrag fragmenting 4725104 3668252 3806898 Extfrag fragmenting for unmovable 6678 7974 7281 Extfrag fragmenting unmovable placed with movable 2051 3829 4017 Extfrag fragmenting for reclaimable 429 1208 1278 Extfrag fragmenting reclaimable placed with movable 369 976 1034 Extfrag fragmenting for movable 4717997 3659070 3798339 With Patch 3: 3.19-rc4 3.19-rc4 3.19-rc4 8-nothp-1 8-nothp-2 8-nothp-3 Page alloc extfrag event 5016183 4700142 3850633 Extfrag fragmenting 5015325 4699613 3850072 Extfrag fragmenting for unmovable 1312 3154 3088 Extfrag fragmenting unmovable placed with movable 1115 2777 2714 Extfrag fragmenting for reclaimable 437 1193 1097 Extfrag fragmenting reclaimable placed with movable 330 969 879 Extfrag fragmenting for movable 5013576 4695266 3845887 In v2 we've seen apparent regression with Patch 1 for unmovable events, this is now gone, suggesting it was indeed noise. Here, each patch improves the situation for unmovable events. Reclaimable is improved by patch 1 and then either the same modulo noise, or perhaps sligtly worse - a small price for unmovable improvements, IMHO. The number of movable allocations falling back to other migratetypes is most noisy, but it's reduced to half at Patch 2 nevertheless. These are least critical as compaction can move them around. If we look at success rates, the patches don't affect them, that didn't change. Baseline: 3.19-rc4 3.19-rc4 3.19-rc4 5-nothp-1 5-nothp-2 5-nothp-3 Success 1 Min 49.00 ( 0.00%) 42.00 ( 14.29%) 41.00 ( 16.33%) Success 1 Mean 51.00 ( 0.00%) 45.00 ( 11.76%) 42.60 ( 16.47%) Success 1 Max 55.00 ( 0.00%) 51.00 ( 7.27%) 46.00 ( 16.36%) Success 2 Min 53.00 ( 0.00%) 47.00 ( 11.32%) 44.00 ( 16.98%) Success 2 Mean 59.60 ( 0.00%) 50.80 ( 14.77%) 48.20 ( 19.13%) Success 2 Max 64.00 ( 0.00%) 56.00 ( 12.50%) 52.00 ( 18.75%) Success 3 Min 84.00 ( 0.00%) 82.00 ( 2.38%) 78.00 ( 7.14%) Success 3 Mean 85.60 ( 0.00%) 82.80 ( 3.27%) 79.40 ( 7.24%) Success 3 Max 86.00 ( 0.00%) 83.00 ( 3.49%) 80.00 ( 6.98%) Patch 1: 3.19-rc4 3.19-rc4 3.19-rc4 6-nothp-1 6-nothp-2 6-nothp-3 Success 1 Min 49.00 ( 0.00%) 44.00 ( 10.20%) 44.00 ( 10.20%) Success 1 Mean 51.80 ( 0.00%) 46.00 ( 11.20%) 45.80 ( 11.58%) Success 1 Max 54.00 ( 0.00%) 49.00 ( 9.26%) 49.00 ( 9.26%) Success 2 Min 58.00 ( 0.00%) 49.00 ( 15.52%) 48.00 ( 17.24%) Success 2 Mean 60.40 ( 0.00%) 51.80 ( 14.24%) 50.80 ( 15.89%) Success 2 Max 63.00 ( 0.00%) 54.00 ( 14.29%) 55.00 ( 12.70%) Success 3 Min 84.00 ( 0.00%) 81.00 ( 3.57%) 79.00 ( 5.95%) Success 3 Mean 85.00 ( 0.00%) 81.60 ( 4.00%) 79.80 ( 6.12%) Success 3 Max 86.00 ( 0.00%) 82.00 ( 4.65%) 82.00 ( 4.65%) Patch 2: 3.19-rc4 3.19-rc4 3.19-rc4 7-nothp-1 7-nothp-2 7-nothp-3 Success 1 Min 50.00 ( 0.00%) 44.00 ( 12.00%) 39.00 ( 22.00%) Success 1 Mean 52.80 ( 0.00%) 45.60 ( 13.64%) 42.40 ( 19.70%) Success 1 Max 55.00 ( 0.00%) 46.00 ( 16.36%) 47.00 ( 14.55%) Success 2 Min 52.00 ( 0.00%) 48.00 ( 7.69%) 45.00 ( 13.46%) Success 2 Mean 53.40 ( 0.00%) 49.80 ( 6.74%) 48.80 ( 8.61%) Success 2 Max 57.00 ( 0.00%) 52.00 ( 8.77%) 52.00 ( 8.77%) Success 3 Min 84.00 ( 0.00%) 81.00 ( 3.57%) 79.00 ( 5.95%) Success 3 Mean 85.00 ( 0.00%) 82.40 ( 3.06%) 79.60 ( 6.35%) Success 3 Max 86.00 ( 0.00%) 83.00 ( 3.49%) 80.00 ( 6.98%) Patch 3: 3.19-rc4 3.19-rc4 3.19-rc4 8-nothp-1 8-nothp-2 8-nothp-3 Success 1 Min 46.00 ( 0.00%) 44.00 ( 4.35%) 42.00 ( 8.70%) Success 1 Mean 50.20 ( 0.00%) 45.60 ( 9.16%) 44.00 ( 12.35%) Success 1 Max 52.00 ( 0.00%) 47.00 ( 9.62%) 47.00 ( 9.62%) Success 2 Min 53.00 ( 0.00%) 49.00 ( 7.55%) 48.00 ( 9.43%) Success 2 Mean 55.80 ( 0.00%) 50.60 ( 9.32%) 49.00 ( 12.19%) Success 2 Max 59.00 ( 0.00%) 52.00 ( 11.86%) 51.00 ( 13.56%) Success 3 Min 84.00 ( 0.00%) 80.00 ( 4.76%) 79.00 ( 5.95%) Success 3 Mean 85.40 ( 0.00%) 81.60 ( 4.45%) 80.40 ( 5.85%) Success 3 Max 87.00 ( 0.00%) 83.00 ( 4.60%) 82.00 ( 5.75%) While there's no improvement here, I consider reduced fragmentation events to be worth on its own. Patch 2 also seems to reduce scanning for free pages, and migrations in compaction, suggesting it has somewhat less work to do: Patch 1: Compaction stalls 4153 3959 3978 Compaction success 1523 1441 1446 Compaction failures 2630 2517 2531 Page migrate success 4600827 4943120 5104348 Page migrate failure 19763 16656 17806 Compaction pages isolated 9597640 10305617 10653541 Compaction migrate scanned 77828948 86533283 87137064 Compaction free scanned 517758295 521312840 521462251 Compaction cost 5503 5932 6110 Patch 2: Compaction stalls 3800 3450 3518 Compaction success 1421 1316 1317 Compaction failures 2379 2134 2201 Page migrate success 4160421 4502708 4752148 Page migrate failure 19705 14340 14911 Compaction pages isolated 8731983 9382374 9910043 Compaction migrate scanned 98362797 96349194 98609686 Compaction free scanned 496512560 469502017 480442545 Compaction cost 5173 5526 5811 As with v2, /proc/pagetypeinfo appears unaffected with respect to numbers of unmovable and reclaimable pageblocks. Configuring the benchmark to allocate like THP page fault (i.e. no sync compaction) gives much noisier results for iterations 2 and 3 after reboot. This is not so surprising given how [1] offers lower improvements in this scenario due to less restarts after deferred compaction which would change compaction pivot. Baseline: 3.19-rc4 3.19-rc4 3.19-rc4 5-thp-1 5-thp-2 5-thp-3 Page alloc extfrag event 8148965 6227815 6646741 Extfrag fragmenting 8147872 6227130 6646117 Extfrag fragmenting for unmovable 10324 12942 15975 Extfrag fragmenting unmovable placed with movable 5972 8495 10907 Extfrag fragmenting for reclaimable 601 1707 2210 Extfrag fragmenting reclaimable placed with movable 520 1570 2000 Extfrag fragmenting for movable 8136947 6212481 6627932 Patch 1: 3.19-rc4 3.19-rc4 3.19-rc4 6-thp-1 6-thp-2 6-thp-3 Page alloc extfrag event 8345457 7574471 7020419 Extfrag fragmenting 8343546 7573777 7019718 Extfrag fragmenting for unmovable 10256 18535 30716 Extfrag fragmenting unmovable placed with movable 6893 11726 22181 Extfrag fragmenting for reclaimable 465 1208 1023 Extfrag fragmenting reclaimable placed with movable 353 996 843 Extfrag fragmenting for movable 8332825 7554034 6987979 Patch 2: 3.19-rc4 3.19-rc4 3.19-rc4 7-thp-1 7-thp-2 7-thp-3 Page alloc extfrag event 3512847 3020756 2891625 Extfrag fragmenting 3511940 3020185 2891059 Extfrag fragmenting for unmovable 9017 6892 6191 Extfrag fragmenting unmovable placed with movable 1524 3053 2435 Extfrag fragmenting for reclaimable 445 1081 1160 Extfrag fragmenting reclaimable placed with movable 375 918 986 Extfrag fragmenting for movable 3502478 3012212 2883708 Patch 3: 3.19-rc4 3.19-rc4 3.19-rc4 8-thp-1 8-thp-2 8-thp-3 Page alloc extfrag event 3181699 3082881 2674164 Extfrag fragmenting 3180812 3082303 2673611 Extfrag fragmenting for unmovable 1201 4031 4040 Extfrag fragmenting unmovable placed with movable 974 3611 3645 Extfrag fragmenting for reclaimable 478 1165 1294 Extfrag fragmenting reclaimable placed with movable 387 985 1030 Extfrag fragmenting for movable 3179133 3077107 2668277 The improvements for first iteration are clear, the rest is much noisier and can appear like regression for Patch 1. Anyway, patch 2 rectifies it. Allocation success rates are again unaffected so there's no point in making this e-mail any longer. [1] http://marc.info/?l=linux-mm&m=142166196321125&w=2 This patch (of 3): When __rmqueue_fallback() is called to allocate a page of order X, it will find a page of order Y >= X of a fallback migratetype, which is different from the desired migratetype. With the help of try_to_steal_freepages(), it may change the migratetype (to the desired one) also of: 1) all currently free pages in the pageblock containing the fallback page 2) the fallback pageblock itself 3) buddy pages created by splitting the fallback page (when Y > X) These decisions take the order Y into account, as well as the desired migratetype, with the goal of preventing multiple fallback allocations that could e.g. distribute UNMOVABLE allocations among multiple pageblocks. Originally, decision for 1) has implied the decision for 3). Commit 47118af0 ("mm: mmzone: MIGRATE_CMA migration type added") changed that (probably unintentionally) so that the buddy pages in case 3) are always changed to the desired migratetype, except for CMA pageblocks. Commit fef903ef ("mm/page_allo.c: restructure free-page stealing code and fix a bug") did some refactoring and added a comment that the case of 3) is intended. Commit 0cbef29a ("mm: __rmqueue_fallback() should respect pageblock type") removed the comment and tried to restore the original behavior where 1) implies 3), but due to the previous refactoring, the result is instead that only 2) implies 3) - and the conditions for 2) are less frequently met than conditions for 1). This may increase fragmentation in situations where the code decides to steal all free pages from the pageblock (case 1)), but then gives back the buddy pages produced by splitting. This patch restores the original intended logic where 1) implies 3). During testing with stress-highalloc from mmtests, this has shown to decrease the number of events where UNMOVABLE and RECLAIMABLE allocations steal from MOVABLE pageblocks, which can lead to permanent fragmentation. In some cases it has increased the number of events when MOVABLE allocations steal from UNMOVABLE or RECLAIMABLE pageblocks, but these are fixable by sync compaction and thus less harmful. Note that evaluation has shown that the behavior introduced by 47118af0 for buddy pages in case 3) is actually even better than the original logic, so the following patch will introduce it properly once again. For stable backports of this patch it makes thus sense to only fix versions containing 0cbef29a. [iamjoonsoo.kim@lge.com: tracepoint fix] Signed-off-by: -
Naoya Horiguchi authored
This patch makes do_mincore() use walk_page_vma(), which reduces many lines of code by using common page table walk code. [daeseok.youn@gmail.com: remove unneeded variable 'err'] Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Daeseok Youn <daeseok.youn@gmail.com> Signed-off-by:
-
Kirill A. Shutemov authored
Currently pagewalker splits all THP pages on any clear_refs request. It's not necessary. We can handle this on PMD level. One side effect is that soft dirty will potentially see more dirty memory, since we will mark whole THP page dirty at once. Sanity checked with CRIU test suite. More testing is required. Signed-off-by:
Cyrill Gorcunov <gorcunov@openvz.org> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Naoya Horiguchi authored
walk_page_range() silently skips vma having VM_PFNMAP set, which leads to undesirable behaviour at client end (who called walk_page_range). For example for pagemap_read(), when no callbacks are called against VM_PFNMAP vma, pagemap_read() may prepare pagemap data for next virtual address range at wrong index. That could confuse and/or break userspace applications. This patch avoid this misbehavior caused by vma(VM_PFNMAP) like follows: - for pagemap_read() which has its own ->pte_hole(), call the ->pte_hole() over vma(VM_PFNMAP), - for clear_refs and queue_pages which have their own ->tests_walk, just return 1 and skip vma(VM_PFNMAP). This is no problem because these are not interested in hole regions, - for other callers, just skip the vma(VM_PFNMAP) as a default behavior. Signed-off-by:
Shiraz Hashim <shashim@codeaurora.org> Signed-off-by:
-
Naoya Horiguchi authored
queue_pages_range() does page table walking in its own way now, but there is some code duplicate. This patch applies page table walker to reduce lines of code. queue_pages_range() has to do some precheck to determine whether we really walk over the vma or just skip it. Now we have test_walk() callback in mm_walk for this purpose, so we can do this replacement cleanly. queue_pages_test_walk() depends on not only the current vma but also the previous one, so queue_pages->prev is introduced to remember it. Signed-off-by:
-
Naoya Horiguchi authored
We don't have to use mm_walk->private to pass vma to the callback function because of mm_walk->vma. And walk_page_vma() is useful if we walk over a single vma. Signed-off-by:
-
Naoya Horiguchi authored
pagewalk.c can handle vma in itself, so we don't have to pass vma via walk->private. And both of mem_cgroup_count_precharge() and mem_cgroup_move_charge() do for each vma loop themselves, but now it's done in pagewalk.c, so let's clean up them. Signed-off-by:
-
Naoya Horiguchi authored
pagewalk.c can handle vma in itself, so we don't have to pass vma via walk->private. And show_numa_map() walks pages on vma basis, so using walk_page_vma() is preferable. Signed-off-by:
-
Naoya Horiguchi authored
Just doing s/gather_hugetbl_stats/gather_hugetlb_stats/g, this makes code grep-friendly. Signed-off-by:
-
Naoya Horiguchi authored
Page table walker has the information of the current vma in mm_walk, so we don't have to call find_vma() in each pagemap_(pte|hugetlb)_range() call any longer. Currently pagemap_pte_range() does vma loop itself, so this patch reduces many lines of code. NULL-vma check is omitted because we assume that we never run these callbacks on any address outside vma. And even if it were broken, NULL pointer dereference would be detected, so we can get enough information for debugging. Signed-off-by:
-
Naoya Horiguchi authored
clear_refs_write() has some prechecks to determine if we really walk over a given vma. Now we have a test_walk() callback to filter vmas, so let's utilize it. Signed-off-by:
-
Naoya Horiguchi authored
pagewalk.c can handle vma in itself, so we don't have to pass vma via walk->private. And show_smap() walks pages on vma basis, so using walk_page_vma() is preferable. Signed-off-by:
-
Naoya Horiguchi authored
Introduce walk_page_vma(), which is useful for the callers which want to walk over a given vma. It's used by later patches. Signed-off-by:
-
Naoya Horiguchi authored
Current implementation of page table walker has a fundamental problem in vma handling, which started when we tried to handle vma(VM_HUGETLB). Because it's done in pgd loop, considering vma boundary makes code complicated and bug-prone. From the users viewpoint, some user checks some vma-related condition to determine whether the user really does page walk over the vma. In order to solve these, this patch moves vma check outside pgd loop and introduce a new callback ->test_walk(). Signed-off-by:
-
Naoya Horiguchi authored
Currently no user of page table walker sets ->pgd_entry() or ->pud_entry(), so checking their existence in each loop is just wasting CPU cycle. So let's remove it to reduce overhead. Signed-off-by:
-
Konstantin Khlebnikov authored
Lockless access to pte in pagemap_pte_range() might race with page migration and trigger BUG_ON(!PageLocked()) in migration_entry_to_page(): CPU A (pagemap) CPU B (migration) lock_page() try_to_unmap(page, TTU_MIGRATION...) make_migration_entry() set_pte_at() <read *pte> pte_to_pagemap_entry() remove_migration_ptes() unlock_page() if(is_migration_entry()) migration_entry_to_page() BUG_ON(!PageLocked(page)) Also lockless read might be non-atomic if pte is larger than wordsize. Other pte walkers (smaps, numa_maps, clear_refs) already lock ptes. Fixes: 052fb0d6 ("proc: report file/anon bit in /proc/pid/pagemap") Signed-off-by:Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reported-by:
Andrey Ryabinin <a.ryabinin@samsung.com> Reviewed-by:
-
Andrea Arcangeli authored
Use the more generic get_user_pages_unlocked which has the additional benefit of passing FAULT_FLAG_ALLOW_RETRY at the very first page fault (which allows the first page fault in an unmapped area to be always able to block indefinitely by being allowed to release the mmap_sem). Signed-off-by:
Andres Lagar-Cavilla <andreslc@google.com> Reviewed-by:
-
Andrea Arcangeli authored
This allows those get_user_pages calls to pass FAULT_FLAG_ALLOW_RETRY to the page fault in order to release the mmap_sem during the I/O. Signed-off-by:
-
Andrea Arcangeli authored
This allows the get_user_pages_fast slow path to release the mmap_sem before blocking. Signed-off-by:
-
Andrea Arcangeli authored
Some callers (like KVM) may want to set the gup_flags like FOLL_HWPOSION to get a proper -EHWPOSION retval instead of -EFAULT to take a more appropriate action if get_user_pages runs into a memory failure. Signed-off-by:
-
Andrea Arcangeli authored
FAULT_FOLL_ALLOW_RETRY allows the page fault to drop the mmap_sem for reading to reduce the mmap_sem contention (for writing), like while waiting for I/O completion. The problem is that right now practically no get_user_pages call uses FAULT_FOLL_ALLOW_RETRY, so we're not leveraging that nifty feature. Andres fixed it for the KVM page fault. However get_user_pages_fast remains uncovered, and 99% of other get_user_pages aren't using it either (the only exception being FOLL_NOWAIT in KVM which is really nonblocking and in fact it doesn't even release the mmap_sem). So this patchsets extends the optimization Andres did in the KVM page fault to the whole kernel. It makes most important places (including gup_fast) to use FAULT_FOLL_ALLOW_RETRY to reduce the mmap_sem hold times during I/O. The only few places that remains uncovered are drivers like v4l and other exceptions that tends to work on their own memory and they're not working on random user memory (for example like O_DIRECT that uses gup_fast and is fully covered by this patch). A follow up patch should probably also add a printk_once warning to get_user_pages that should go obsolete and be phased out eventually. The "vmas" parameter of get_user_pages makes it fundamentally incompatible with FAULT_FOLL_ALLOW_RETRY (vmas array becomes meaningless the moment the mmap_sem is released). While this is just an optimization, this becomes an absolute requirement for the userfaultfd feature http://lwn.net/Articles/615086/ . The userfaultfd allows to block the page fault, and in order to do so I need to drop the mmap_sem first. So this patch also ensures that all memory where userfaultfd could be registered by KVM, the very first fault (no matter if it is a regular page fault, or a get_user_pages) always has FAULT_FOLL_ALLOW_RETRY set. Then the userfaultfd blocks and it is waken only when the pagetable is already mapped. The second fault attempt after the wakeup doesn't need FAULT_FOLL_ALLOW_RETRY, so it's ok to retry without it. This patch (of 5): We can leverage the VM_FAULT_RETRY functionality in the page fault paths better by using either get_user_pages_locked or get_user_pages_unlocked. The former allows conversion of get_user_pages invocations that will have to pass a "&locked" parameter to know if the mmap_sem was dropped during the call. Example from: down_read(&mm->mmap_sem); do_something() get_user_pages(tsk, mm, ..., pages, NULL); up_read(&mm->mmap_sem); to: int locked = 1; down_read(&mm->mmap_sem); do_something() get_user_pages_locked(tsk, mm, ..., pages, &locked); if (locked) up_read(&mm->mmap_sem); The latter is suitable only as a drop in replacement of the form: down_read(&mm->mmap_sem); get_user_pages(tsk, mm, ..., pages, NULL); up_read(&mm->mmap_sem); into: get_user_pages_unlocked(tsk, mm, ..., pages); Where tsk, mm, the intermediate "..." paramters and "pages" can be any value as before. Just the last parameter of get_user_pages (vmas) must be NULL for get_user_pages_locked|unlocked to be usable (the latter original form wouldn't have been safe anyway if vmas wasn't null, for the former we just make it explicit by dropping the parameter). If vmas is not NULL these two methods cannot be used. Signed-off-by:
Peter Feiner <pfeiner@google.com> Reviewed-by:
-
Vlastimil Babka authored
The previous commit ("mm/thp: Allocate transparent hugepages on local node") introduced alloc_hugepage_vma() to mm/mempolicy.c to perform a special policy for THP allocations. The function has the same interface as alloc_pages_vma(), shares a lot of boilerplate code and a long comment. This patch merges the hugepage special case into alloc_pages_vma. The extra if condition should be cheap enough price to pay. We also prevent a (however unlikely) race with parallel mems_allowed update, which could make hugepage allocation restart only within the fallback call to alloc_hugepage_vma() and not reconsider the special rule in alloc_hugepage_vma(). Also by making sure mpol_cond_put(pol) is always called before actual allocation attempt, we can use a single exit path within the function. Also update the comment for missing node parameter and obsolete reference to mm_sem. Signed-off-by: -
Aneesh Kumar K.V authored
This make sure that we try to allocate hugepages from local node if allowed by mempolicy. If we can't, we fallback to small page allocation based on mempolicy. This is based on the observation that allocating pages on local node is more beneficial than allocating hugepages on remote node. With this patch applied we may find transparent huge page allocation failures if the current node doesn't have enough freee hugepages. Before this patch such failures result in us retrying the allocation on other nodes in the numa node mask. [akpm@linux-foundation.org: fix comment, add CONFIG_TRANSPARENT_HUGEPAGE dependency] Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by:
-
Joonsoo Kim authored
Compaction deferring logic is heavy hammer that block the way to the compaction. It doesn't consider overall system state, so it could prevent user from doing compaction falsely. In other words, even if system has enough range of memory to compact, compaction would be skipped due to compaction deferring logic. This patch add new tracepoint to understand work of deferring logic. This will also help to check compaction success and fail. Signed-off-by:
Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Signed-off-by:
-
Joonsoo Kim authored
It is not well analyzed that when/why compaction start/finish or not. With these new tracepoints, we can know much more about start/finish reason of compaction. I can find following bug with these tracepoint. http://www.spinics.net/lists/linux-mm/msg81582.htmlSigned-off-by:
-
Joonsoo Kim authored
It'd be useful to know current range where compaction work for detailed analysis. With it, we can know pageblock where we actually scan and isolate, and, how much pages we try in that pageblock and can guess why it doesn't become freepage with pageblock order roughly. Signed-off-by:
-
Joonsoo Kim authored
We now have tracepoint for begin event of compaction and it prints start position of both scanners, but, tracepoint for end event of compaction doesn't print finish position of both scanners. It'd be also useful to know finish position of both scanners so this patch add it. It will help to find odd behavior or problem on compaction internal logic. And mode is added to both begin/end tracepoint output, since according to mode, compaction behavior is quite different. And lastly, status format is changed to string rather than status number for readability. [akpm@linux-foundation.org: fix sparse warning] Signed-off-by:
-
Joonsoo Kim authored
To check the range that compaction is working, tracepoint print start/end pfn of zone and start pfn of both scanner with decimal format. Since we manage all pages in order of 2 and it is well represented by hexadecimal, this patch change the tracepoint format from decimal to hexadecimal. This would improve readability. For example, it makes us easily notice whether current scanner try to compact previously attempted pageblock or not. Signed-off-by:
-
Konstantin Khebnikov authored
Helper account_page_redirty() fixes dirty pages counter for redirtied pages. This patch puts it after dirtying and prevents temporary underflows of dirtied pages counters on zone/bdi and current->nr_dirtied. Signed-off-by:
-
Kirill A. Shutemov authored
The problem is that we check nr_ptes/nr_pmds in exit_mmap() which happens *before* pgd_free(). And if an arch does pte/pmd allocation in pgd_alloc() and frees them in pgd_free() we see offset in counters by the time of the checks. We tried to workaround this by offsetting expected counter value according to FIRST_USER_ADDRESS for both nr_pte and nr_pmd in exit_mmap(). But it doesn't work in some cases: 1. ARM with LPAE enabled also has non-zero USER_PGTABLES_CEILING, but upper addresses occupied with huge pmd entries, so the trick with offsetting expected counter value will get really ugly: we will have to apply it nr_pmds, but not nr_ptes. 2. Metag has non-zero FIRST_USER_ADDRESS, but doesn't do allocation pte/pmd page tables allocation in pgd_alloc(), just setup a pgd entry which is allocated at boot and shared accross all processes. The proposal is to move the check to check_mm() which happens *after* pgd_free() and do proper accounting during pgd_alloc() and pgd_free() which would bring counters to zero if nothing leaked. Signed-off-by:
Tyler Baker <tyler.baker@linaro.org> Tested-by:
Nishanth Menon <nm@ti.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: James Hogan <james.hogan@imgtec.com> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Signed-off-by:
-
Kirill A. Shutemov authored
Dave noticed that unprivileged process can allocate significant amount of memory -- >500 MiB on x86_64 -- and stay unnoticed by oom-killer and memory cgroup. The trick is to allocate a lot of PMD page tables. Linux kernel doesn't account PMD tables to the process, only PTE. The use-cases below use few tricks to allocate a lot of PMD page tables while keeping VmRSS and VmPTE low. oom_score for the process will be 0. #include <errno.h> #include <stdio.h> #include <stdlib.h> #include <unistd.h> #include <sys/mman.h> #include <sys/prctl.h> #define PUD_SIZE (1UL << 30) #define PMD_SIZE (1UL << 21) #define NR_PUD 130000 int main(void) { char *addr = NULL; unsigned long i; prctl(PR_SET_THP_DISABLE); for (i = 0; i < NR_PUD ; i++) { addr = mmap(addr + PUD_SIZE, PUD_SIZE, PROT_WRITE|PROT_READ, MAP_ANONYMOUS|MAP_PRIVATE, -1, 0); if (addr == MAP_FAILED) { perror("mmap"); break; } *addr = 'x'; munmap(addr, PMD_SIZE); mmap(addr, PMD_SIZE, PROT_WRITE|PROT_READ, MAP_ANONYMOUS|MAP_PRIVATE|MAP_FIXED, -1, 0); if (addr == MAP_FAILED) perror("re-mmap"), exit(1); } printf("PID %d consumed %lu KiB in PMD page tables\n", getpid(), i * 4096 >> 10); return pause(); } The patch addresses the issue by account PMD tables to the process the same way we account PTE. The main place where PMD tables is accounted is __pmd_alloc() and free_pmd_range(). But there're few corner cases: - HugeTLB can share PMD page tables. The patch handles by accounting the table to all processes who share it. - x86 PAE pre-allocates few PMD tables on fork. - Architectures with FIRST_USER_ADDRESS > 0. We need to adjust sanity check on exit(2). Accounting only happens on configuration where PMD page table's level is present (PMD is not folded). As with nr_ptes we use per-mm counter. The counter value is used to calculate baseline for badness score by oom-killer. Signed-off-by:Dave Hansen <dave.hansen@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Reviewed-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
-
Kirill A. Shutemov authored
ARM uses custom implementation of PMD folding in 2-level page table case. Generic code expects to see __PAGETABLE_PMD_FOLDED to be defined if PMD is folded, but ARM doesn't do this. Let's fix it. Defining __PAGETABLE_PMD_FOLDED will drop out unused __pmd_alloc(). It also fixes problems with recently-introduced pmd accounting on ARM without LPAE. Signed-off-by:
Simon Horman <horms@verge.net.au> Tested-by:
Simon Horman <horms+renesas@verge.net.au> Tested-by:
Fabio Estevam <festevam@gmail.com> Tested-by:
Felipe Balbi <balbi@ti.com> Tested-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Pavel Emelyanov <xemul@openvz.org> Cc: David Rientjes <rientjes@google.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by:
-
Kirill A. Shutemov authored
If an architecure uses <asm-generic/4level-fixup.h>, build fails if we try to use PUD_SHIFT in generic code: In file included from arch/microblaze/include/asm/bug.h:1:0, from include/linux/bug.h:4, from include/linux/thread_info.h:11, from include/asm-generic/preempt.h:4, from arch/microblaze/include/generated/asm/preempt.h:1, from include/linux/preempt.h:18, from include/linux/spinlock.h:50, from include/linux/mmzone.h:7, from include/linux/gfp.h:5, from include/linux/slab.h:14, from mm/mmap.c:12: mm/mmap.c: In function 'exit_mmap': >> mm/mmap.c:2858:46: error: 'PUD_SHIFT' undeclared (first use in this function) round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT); ^ include/asm-generic/bug.h:86:25: note: in definition of macro 'WARN_ON' int __ret_warn_on = !!(condition); \ ^ mm/mmap.c:2858:46: note: each undeclared identifier is reported only once for each function it appears in round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT); ^ include/asm-generic/bug.h:86:25: note: in definition of macro 'WARN_ON' int __ret_warn_on = !!(condition); \ ^ As with <asm-generic/pgtable-nopud.h>, let's define PUD_SHIFT to PGDIR_SHIFT. Signed-off-by:Wu Fengguang <fengguang.wu@intel.com> Signed-off-by:
-
Kirill A. Shutemov authored
LKP has triggered a compiler warning after my recent patch "mm: account pmd page tables to the process": mm/mmap.c: In function 'exit_mmap': >> mm/mmap.c:2857:2: warning: right shift count >= width of type [enabled by default] The code: > 2857 WARN_ON(mm_nr_pmds(mm) > 2858 round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT); In this, on tile, we have FIRST_USER_ADDRESS defined as 0. round_up() has the same type -- int. PUD_SHIFT. I think the best way to fix it is to define FIRST_USER_ADDRESS as unsigned long. On every arch for consistency. Signed-off-by: -
Kirill A. Shutemov authored
Microblaze uses custom implementation of PMD folding, but doesn't define __PAGETABLE_PMD_FOLDED, which generic code expects to see. Let's fix it. Defining __PAGETABLE_PMD_FOLDED will drop out unused __pmd_alloc(). It also fixes problems with recently-introduced pmd accounting. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Tested-by:
-
Johannes Weiner authored
The swap controller code is scattered all over the file. Gather all the code that isn't directly needed by the memory controller at the end of the file in its own CONFIG_MEMCG_SWAP section. Signed-off-by:
Vladimir Davydov <vdavydov@parallels.com> Signed-off-by:
-
