- 08 Jun, 2009 29 commits
-
-
Vasu Dev authored
Removes periodic fcoe_watchdog timer used across all fcoe interface maintained in fcoe_hostlist instead added new fcoe_queue_timer per fcoe interface. Added timer is armed only when some pending skb need to be flushed as oppose to periodic 1 second fcoe_watchdog, since now fcoe_queue_timer is used on demand thus set this to 2 jiffies. Now fcoe_queue_timer is much simple than fcoe_watchdog using lock to process all fcoe interface from fcoe_hostlist. I noticed +ve performance result with using 2 jiffies timer as this helps flushing fcoe_pending_queue quickly. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Vasu Dev authored
Currently fcoe_pending_queue.lock held twice for every new skb adding to this queue when already least one pkt is pending in this queue and that is not uncommon once skb pkts starts getting queued here upon fcoe_start_io => dev_queue_xmit failure. This patch moves most fcoe_pending_queue logic to fcoe_check_wait_queue function, this new logic grabs fcoe_pending_queue.lock only once to add a new skb instead twice as used to be. I think after this patch call flow around fcoe_check_wait_queue calling in fcoe_xmit is bit simplified with modified fcoe_check_wait_queue function taking care of adding and removing pending skb in one function. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Steve Ma authored
When a sequence is received in response to an exchange we issued previously, we should check to see if the exchange has completed. If yes, the sequence should be discarded. Since the exchange might be still in the completion process, it should be untouched. Signed-off-by: Steve Ma <steve.ma@intel.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
If we aborted a command, because it timed out we should not use DID_ABORT. It will fail the command right away back to the upper layer. We want to use something that indicated that the problem did not complete normally, but it was not a fatal problem. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Chris Leech authored
FIP frames should leave the fcoe layer with skb->protocol set to ETH_P_FIP, not ETH_P_802_3. Signed-off-by: Chris Leech <christopher.leech@intel.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Joe Eykholt authored
When a reset is sent using fcoeadm on a non-FIP mode NIC, there's no link flap, so the fcoe_ctlr stays in non-FIP mode. In that case, FIP wasn't setting the flogi_oxid or map_dest flag, causing the FLOGI to be sent with the both wrong source MAC and the wrong destination MAC address, causing it to fail. This leads to a non-functioning HBA until a link flap or instance delete/create. Signed-off-by: Joe Eykholt <jeykholt@cisco.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Herbert Xu authored
This driver needs dst_cache->dev so it should include net/dst.h to ensure that it builds. While net/tcp.h probably includes it already, we shouldn't rely on that since there is no guarantee that this won't change in future. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
Bump driver version Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
There are several scenarios where the ibmvfc driver needs to try to log back into a target on the fabric. Today when these events occur, we simply go through re-discovery for all attached targets, assuming that either the query of the name server or an ADISC will indicate we might need to log back into the target, which doesn't work for all scenarios. Fix this by taking note of the affected target(s) in these conditions and ensuring we try to PLOGI back into the target. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
For certain scenarios during device rediscovery, we detect we need to log back into a target. Currently we do just that - PLOGI/PRLI back into the target. Change the code to delete and add the target from the FC transport layer as well, to ensure we handle any cases where the target may have changed. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
The virtual I/O server controlling the NPIV adapter associated with a virtual fibre channel adapter can send a HALT event to the client. When this occurs, the client can no longer send commands until a RESUME is received. By adding support for flush on halt, we will get all of our outstanding commands flushed back before the Virtual I/O server enters the halt state, eliminating potential command timeouts for outstanding commands which might occur if we did not support this feature. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
This patch adds support for a new command supported by the Virtual I/O Server, NPIV Logout. The command will abort all outstanding commands and log out of the fabric. Currently, the only way to do this is by breaking the CRQ, which can take a fairly long time when lots of commands are outstanding. The NPIV Logout commands provides a mechanism to accomplish virtually the same function, but is much faster. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
Fixes the following deadlock scenario shown below. We currently allow queuecommand to send commands when the ibmvfc workqueue is scanning for new rports, so we should also allow EH to function at this time as well. scsi_eh_3 D 0000000000000000 12304 1279 2 Call Trace: [c0000002f7257730] [c0000002f72577e0] 0xc0000002f72577e0 (unreliable) [c0000002f7257900] [c0000000000118f4] .__switch_to+0x158/0x1a0 [c0000002f72579a0] [c0000000004f8b40] .schedule+0x8d4/0x9dc [c0000002f7257b60] [c0000000004f8f08] .schedule_timeout+0xa8/0xe8 [c0000002f7257c50] [d0000000001d23e0] .ibmvfc_wait_while_resetting+0xe4/0x140 [ibmvfc] [c0000002f7257d20] [d0000000001d3984] .ibmvfc_eh_abort_handler+0x60/0xe4 [ibmvfc] [c0000002f7257dc0] [d000000000366714] .scsi_error_handler+0x38c/0x674 [scsi_mod] [c0000002f7257f00] [c0000000000a7470] .kthread+0x78/0xc4 [c0000002f7257f90] [c000000000029b8c] .kernel_thread+0x4c/0x68 ibmvfc_3 D 0000000000000000 12432 1280 2 Call Trace: [c0000002f7253540] [c0000002f72535f0] 0xc0000002f72535f0 (unreliable) [c0000002f7253710] [c0000000000118f4] .__switch_to+0x158/0x1a0 [c0000002f72537b0] [c0000000004f8b40] .schedule+0x8d4/0x9dc [c0000002f7253970] [c0000000004f8e98] .schedule_timeout+0x38/0xe8 [c0000002f7253a60] [c0000000004f80cc] .wait_for_common+0x138/0x220 [c0000002f7253b40] [c0000000000a2784] .flush_cpu_workqueue+0xac/0xcc [c0000002f7253c10] [c0000000000a2960] .flush_workqueue+0x58/0xa0 [c0000002f7253ca0] [d0000000000827fc] .fc_flush_work+0x4c/0x64 [scsi_transport_fc] [c0000002f7253d20] [d000000000082db4] .fc_remote_port_add+0x48/0x6c4 [scsi_transport_fc] [c0000002f7253dd0] [d0000000001d7d04] .ibmvfc_work+0x820/0xa7c [ibmvfc] [c0000002f7253f00] [c0000000000a7470] .kthread+0x78/0xc4 [c0000002f7253f90] [c000000000029b8c] .kernel_thread+0x4c/0x68 fc_wq_3 D 0000000000000000 10720 1283 2 Call Trace: [c0000002f559ac30] [c0000002f559ace0] 0xc0000002f559ace0 (unreliable) [c0000002f559ae00] [c0000000000118f4] .__switch_to+0x158/0x1a0 [c0000002f559aea0] [c0000000004f8b40] .schedule+0x8d4/0x9dc [c0000002f559b060] [c0000000004f8e98] .schedule_timeout+0x38/0xe8 [c0000002f559b150] [c0000000004f80cc] .wait_for_common+0x138/0x220 [c0000002f559b230] [c0000000002721c4] .blk_execute_rq+0xb4/0x100 [c0000002f559b360] [d00000000036a1f8] .scsi_execute+0x118/0x194 [scsi_mod] [c0000002f559b420] [d00000000036a32c] .scsi_execute_req+0xb8/0x124 [scsi_mod] [c0000002f559b500] [d0000000000c1330] .sd_sync_cache+0x8c/0x108 [sd_mod] [c0000002f559b5e0] [d0000000000c15b4] .sd_shutdown+0x9c/0x158 [sd_mod] [c0000002f559b660] [d0000000000c16d0] .sd_remove+0x60/0xb4 [sd_mod] [c0000002f559b700] [c000000000392ecc] .__device_release_driver+0xd0/0x118 [c0000002f559b7a0] [c000000000393080] .device_release_driver+0x30/0x54 [c0000002f559b830] [c000000000392108] .bus_remove_device+0x128/0x16c [c0000002f559b8d0] [c00000000038f94c] .device_del+0x158/0x234 [c0000002f559b960] [d00000000036f078] .__scsi_remove_device+0x5c/0xd4 [scsi_mod] [c0000002f559b9f0] [d00000000036f124] .scsi_remove_device+0x34/0x58 [scsi_mod] [c0000002f559ba80] [d00000000036f204] .__scsi_remove_target+0xb4/0x120 [scsi_mod] [c0000002f559bb10] [d00000000036f338] .__remove_child+0x2c/0x44 [scsi_mod] [c0000002f559bb90] [c00000000038f11c] .device_for_each_child+0x54/0xb4 [c0000002f559bc50] [d00000000036f2e0] .scsi_remove_target+0x70/0x9c [scsi_mod] [c0000002f559bce0] [d000000000083454] .fc_starget_delete+0x24/0x3c [scsi_transport_fc] [c0000002f559bd70] [c0000000000a2368] .run_workqueue+0x118/0x208 [c0000002f559be30] [c0000000000a2580] .worker_thread+0x128/0x154 [c0000002f559bf00] [c0000000000a7470] .kthread+0x78/0xc4 [c0000002f559bf90] [c000000000029b8c] .kernel_thread+0x4c/0x68 Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
The ibmvfc driver currently logs errors during discovery for several transient fabric errors, which generally get retried. If retries do not work, we see multiple errors in the log. If retries do work, we see errors in the log which may be confusing since the retry worked. This patch enhances the discovery time error logging to only log errors for command failures during discovery if all allowed retries have been used up. The existing behavior of logging all failures can be restored by setting the hosts log_level to a value of 3 or greater. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
Use DEVICE_ATTR macro for defining device sysfs attributes. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
Since target allocations can occur while resetting the virtual adapter, we shouldn't be using GFP_KERNEL for them as it could hang. Switch to use GFP_NOIO. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Brian King authored
Fix an obvious bug in processing error responses for SCSI commands which can result in successful responses being incorrectly returned with DID_ERROR. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Bottomley authored
The async split up of probing in sd.c created a potential failure case where something goes wrong with device_add(), but which we don't recover properly. Since, in general, asynchronous error handling is hard, move the device_add() into the asynchronous path (it should be fast) and make sure all the deferred processing cannot fail. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Bottomley authored
The Documentation is incorrect (we removed some functions referred to), and none of the bug warnings now apply. Additionally remove the spurious check on the return from blk_get_request() which can't fail if __GFP_WAIT is passed in. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
Add support for persistent vport definitions at creation at boot time Also includes a few misc fixes for: - conversion to vpi name from vport slang name - couple of small mailbox references - some additional discovery mods Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
Miscellaneous Changes: - Convert from SLI2_ACTIVE flag to more correct SLI_ACTIVE (generic) flag - Reposition log verbose messaging definitions - Update naming for vpi object name from vport slang name - Handle deferred error attention condition - Add 10G link support - Small bug fixup Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
Update of copyrights on modified files Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
SLI4 supports both FC and FCOE, with some extended topology objects. This patch adss support for the objects, and updates the disovery engines for their use. Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
The mailbox commands themselves are the same, or very similar to their SLI3 counterparts. This patch genericizes mailbox command handling and adds support for the new SLI4 mailbox queue. Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
Adds support for the new queues in the SLI-4 interface. There are : - Work Queues - host-to-adapter for fast-path traffic - Mailbox Queues - host-to-adapter for control (slow-path) - Buffer Queues - host-to-adapter for posting buffers for async receive - Completion Queues - adapter-to-host for posting async events, completions for fast or slow patch work, receipt of async receive traffic - Event Queues - tied to MSI-X vectors, binds completion queues with interrupts These patches add the all the support code to tie into command submission and response paths, updates the interrupt handling, etc. Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
Adds new hardware and interface definitions. Adds new interface routines - utilizing the reorganized layout of the driver. Adds SLI-4 specific functions for attachment, initialization, teardown, etc. Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Smart authored
Preps the organization of the driver so that the bottom half, which interacts with the hardware, can share common code sequences for attachment, detachment, initialization, teardown, etc with new hardware. For very common code sections, which become specific to the interface type, the driver uses an indirect function call. The function is set at initialization. For less common sections, such as initialization, the driver looks at the interface type and calls the routines relative to the interface. Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
- 23 May, 2009 11 commits
-
-
Abhijeet Joglekar authored
This allows fnic to configure number of retries for lport and rport separately. Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com> Acked-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Eric Moore authored
Bump driver version. Signed-off-by: Eric Moore <eric.moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Eric Moore authored
This fix's is for all local function so their name has the "_" preceeding the module name, then function name. Most the code is already is using this naming convention. Signed-off-by: Eric Moore <eric.moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Eric Moore authored
This patch will find an active mid for a query_task request via the ioctl path. This code is already there for task_abort, so this patch combining code using the same fuction _ctl_set_task_mid(), previously _ctl_do_task_abort(). Signed-off-by: Eric Moore <eric.moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Eric Moore authored
Adding new eh_target_reset_handler for target reset. Change the eh_device_reset_handler so its sending MPI2_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET, instead of MPI2_SCSITASKMGMT_TASKTYPE_TARGET_RESET. Add new function _scsih_scsi_lookup_find_by_lun as a sanity check to insure I_T_L commands are completed upon completing lun reset. Signed-off-by: Eric Moore <eric.moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Eric Moore authored
This add support for type 1 and 3 DIF support per the Oracle API. Signed-off-by: Eric Moore <eric.moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Christof Schmitt authored
Keep the information about the device and model id in zfcp_ccw. This requires an additional helper function to check for the privileged cfdc subchannel, but it allows the removal of the redundant defines from the zfcp_def header file. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Swen Schillig authored
If the destination ID (D_ID) of a remote storage port changed, e.g. re-plugged cable on the switch in a different switch port, the port was never (re-)attached within Linux. This patch fixes the broken mapping between the WWPN and the D_ID. Signed-off-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Martin Petermann authored
In rare cases, open port request might timeout, erp calls zfcp_port_put, port gets dequeued. Now, the late returning (or dismissed) fsf-port-open calls the fsf_port_open_handler that tries to reference the port data structure leading to a kernel oops. Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Christof Schmitt authored
Add comments where there is a deliberate fall through in switch/case statements. This makes some code checkers happy and makes it clear that there is no missing break statement. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Christof Schmitt authored
enum dma_data_direction only has the 4 values DMA_BIDIRECTIONAL, DMA_TO_DEVICE, DMA_FROM_DEVICE and DMA_NONE. No need to have the default case. While changing this, setup sbtype in one place to make sparse happy. The default value of retval is already -EIO, so remove the additional assignment for these two cases. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-