Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Copy the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Use a zero'ed array on the stack, then call eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Use an array on the stack, then call eth_hw_addr_set().
eth_hw_addr_set() is after error checking, this should
be fine, error propagates all the way to failing probe.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Break the address apart into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

macaddr[] is a module param, and int, so copy the address into
an array of u8 on the stack, then call eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The last argument of device_create() call should be a template string.
The tap_name variable should be the argument to the string, but not the
argument of the call itself.  We should add the template string and turn
tap_name into its argument.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The last argument of device_create() call should be a template string.
The tap_name variable should be the argument to the string, but not the
argument of the call itself.  We should add the template string and turn
tap_name into its argument.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2021-10-15

1) From Rongwei Liu:

Use system_image_guid and native_port_num when bonding.
Don't relay on PCIe ids anymore.

With some specific NIC, the physical devices may have PCIe IDs like
0001:01:00.0/1 and 0002:02:00.0/1. All of these devices should have
the same system_image_guid and device index can be queried from
native_port_num.

For matching sibling devices/port of the same HCA, compare the HCA
GUID reported on each device rather than just assuming PCIe ids have
similar attributes.

2) From Amir Tzin: Use HCA defined Timouts

Replace hard coded timeouts with values stored by firmware in default
timeouts register (DTOR). Timeouts are read during driver load. If DTOR
is not supported by firmware then fallback to hard coded defaults
instead.

3) From Shay Drory: Disable roce at HCA level
Disable RoCE in Firmware when devlink roce parameter is set to off.

4) A small set of trivial cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-10-14

Maciej Machnikowski says:

Extend the driver implementation to support PTP pins on E810-T and
derivative devices.

E810-T adapters are equipped with:
- 2 external bidirectional SMA connectors
- 1 internal TX U.FL shared with SMA1
- 1 internal RX U.FL shared with SMA2

The SMA and U.FL configuration is controlled by the external
multiplexer.

E810-T Derivatives are equipped with:
- 2 1PPS outputs on SDP20 and SDP22
- 2 1PPS inputs on SDP21 and SDP23
---
v2:
- Remove defensive programming check and simplify return statement
  (Patch 3)
- Remove unnecessary parentheses (Patch 4)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: A few fixes

This set has three separate changes for the net-next tree:

Patch 1 guarantees safe handling and a warning if a NULL value is
encountered when gathering subflow data for the MPTCP_SUBFLOW_ADDRS
socket option.

Patch 2 increases the default number of subflows allowed per MPTCP
connection.

Patch 3 makes an existing function 'static'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is only used within pm_netlink.c now.

Fixes: 06706542 ("mptcp: add the outgoing MP_PRIO support")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current default does not allowing additional subflows, mostly
as a safety restriction to avoid uncontrolled resource consumption
on busy servers.

Still the system admin and/or the application have to opt-in to
MPTCP explicitly. After that, they need to change (increase) the
default maximum number of additional subflows.

Let set that to reasonable default, and make end-users life easier.

Additionally we need to update some self-tests accordingly.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Coverity complains of a possible NULL dereference in
mptcp_getsockopt_subflow_addrs():

 861       } else if (sk->sk_family == AF_INET6) {
    	3. returned_null: inet6_sk returns NULL. [show details]
    	4. var_assigned: Assigning: np = NULL return value from inet6_sk.
 862                const struct ipv6_pinfo *np = inet6_sk(sk);

Fix this by checking for NULL.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/231
Fixes: c11c5906 ("mptcp: add MPTCP_SUBFLOW_ADDRS getsockopt support")
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
[mjm: Added WARN_ON_ONCE() to the unexpected case]
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With specific NICs, the PFs may have different PCIe ids like
0001:01:00.0/1 and 0002:02:00:00/1.

For PFs with the same system_image_guid, driver should consider
them under the same physical NIC and they are legal to bond together.

If firmware doesn't support system_image_guid, set it to zero and
fallback to use PCIe ids.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Using "native_port_num" can support more NICs.

Fallback to PCIe IDs if "native_port_num" query fails.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Downstream patches.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When querying system_image_guid from firmware, we should check return
value first. The buffer content is valid only if query succeed.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.

So, refactor the code a bit to use the purpose specific kcalloc()
function instead of the argument size * count in the kzalloc() function.

[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-argumentsSigned-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

As multiple places EOPNOTSUPP and EINVAL is returned from driver
it becomes difficult to understand the reason only with error code.
With the netlink extack message exact reason will be known and will
aid in debugging.
Signed-off-by: Abhiram R N <abhiramrn@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

If CT fails to initialize it's rhashtables, it doesn't destroy
the ct nat global table.

Destroy the ct nat global table on ct init failure.

Fixes: d7cade51 ("net/mlx5e: check return value of rhashtable_init")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, when a user disables roce via the devlink param, this change
isn't passed down to the device.
If device allows disabling RoCE at device level, make use of it. This
instructs the device to skip memory allocations related to RoCE
functionality which otherwise is done by the device.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Enable steering IPoIB packets via ethtool, the same way it is done today
for Ethernet packets.
Signed-off-by: Moosa Baransi <moosab@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, SMFS mode doesn't support rx-loopback flows which causes bridge
egress rules to be rejected because without hint rules for both rx and tx
destinations are created by default. Provide explicit flow source hints for
compatibility with SMFS.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Replace hard coded timeouts with values stored by firmware in default
timeouts register (DTOR). Timeouts are read during driver load. If DTOR
is not supported by firmware then fallback to hard coded defaults
instead.
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Replace hard coded timeouts with values stored in firmware's init
segment. Timeouts are read from init segment during driver load. If init
segment timeouts are not supported then fallback to hard coded defaults
instead. Also move pre initialization timeouts which cannot be read from
firmware to the new mechanism.
Signed-off-by: Amir Tzin <amirtz@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add needed structures and defines for DTOR (default timeouts register).
This will be used to get timeouts values from FW instead of hard coded
values in the driver code thus enabling support for slower devices which
need longer timeouts.
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Go through the code base and use ice_for_each_* macros.  While at it,
introduce ice_for_each_xdp_txq() macro that can be used for looping over
xdp_rings array.

Commit is not introducing any new functionality.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.

Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.

Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Optimize Tx descriptor cleaning for XDP. Current approach doesn't
really scale and chokes when multiple flows are handled.

Introduce two ring fields, @next_dd and @next_rs that will keep track of
descriptor that should be looked at when the need for cleaning arise and
the descriptor that should have the RS bit set, respectively.

Note that at this point the threshold is a constant (32), but it is
something that we could make configurable.

First thing is to get away from setting RS bit on each descriptor. Let's
do this only once NTU is higher than the currently @next_rs value. In
such case, grab the tx_desc[next_rs], set the RS bit in descriptor and
advance the @next_rs by a 32.

Second thing is to clean the Tx ring only when there are less than 32
free entries. For that case, look up the tx_desc[next_dd] for a DD bit.
This bit is written back by HW to let the driver know that xmit was
successful. It will happen only for those descriptors that had RS bit
set. Clean only 32 descriptors and advance the DD bit.

Actual cleaning routine is moved from ice_napi_poll() down to the
ice_xmit_xdp_ring(). It is safe to do so as XDP ring will not get any
SKBs in there that would rely on interrupts for the cleaning. Nice side
effect is that for rare case of Tx fallback path (that next patch is
going to introduce) we don't have to trigger the SW irq to clean the
ring.

With those two concepts, ring is kept at being almost full, but it is
guaranteed that driver will be able to produce Tx descriptors.

This approach seems to work out well even though the Tx descriptors are
produced in one-by-one manner. Test was conducted with the ice HW
bombarded with packets from HW generator, configured to generate 30
flows.

Xdp2 sample yields the following results:
<snip>
proto 17:   79973066 pkt/s
proto 17:   80018911 pkt/s
proto 17:   80004654 pkt/s
proto 17:   79992395 pkt/s
proto 17:   79975162 pkt/s
proto 17:   79955054 pkt/s
proto 17:   79869168 pkt/s
proto 17:   79823947 pkt/s
proto 17:   79636971 pkt/s
</snip>

As that sample reports the Rx'ed frames, let's look at sar output.
It says that what we Rx'ed we do actually Tx, no noticeable drops.
Average:        IFACE   rxpck/s   txpck/s    rxkB/s    txkB/s   rxcmp/s txcmp/s  rxmcst/s   %ifutil
Average:       ens4f1 79842324.00 79842310.40 4678261.17 4678260.38 0.00      0.00      0.00     38.32

with tx_busy staying calm.

When compared to a state before:
Average:        IFACE   rxpck/s   txpck/s    rxkB/s    txkB/s   rxcmp/s txcmp/s  rxmcst/s   %ifutil
Average:       ens4f1 90919711.60 42233822.60 5327326.85 2474638.04 0.00      0.00      0.00     43.64

it can be observed that the amount of txpck/s is almost doubled, meaning
that the performance is improved by around 90%. All of this due to the
drops in the driver, previously the tx_busy stat was bumped at a 7mpps
rate.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

With rings being split, it is now convenient to introduce a pointer to
XDP ring within the Rx ring. For XDP_TX workloads this means that
xdp_rings array access will be skipped, which was executed per each
processed frame.

Also, read the XDP prog once per NAPI and if prog is present, set up the
local xdp_ring pointer. Reading prog a single time was discussed in [1]
with some concern raised by Toke around dispatcher handling and having
the need for going through the RCU grace period in the ndo_bpf driver
callback, but ice currently is torning down NAPI instances regardless of
the prog presence on VSI.

Although the pointer to XDP ring introduced to Rx ring makes things a
lot slimmer/simpler, I still feel that single prog read per NAPI
lifetime is beneficial.

Further patch that will introduce the fallback path will also get a
profit from that as xdp_ring pointer will be set during the XDP rings
setup.

[1]: https://lore.kernel.org/bpf/87k0oseo6e.fsf@toke.dk/Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

xdp_frame is not needed for XDP_TX data path in ice driver case.
For this data path cleaning of sent descriptor will not happen anywhere
outside of the driver, which means that carrying the information about
the underlying memory model via xdp_frame will not be used. Therefore,
this conversion can be simply dropped, which would relieve CPU a bit.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There has been a long lasting issue of improper xdp_rings indexing for
XDP_TX and XDP_REDIRECT actions. Given that currently rx_ring->q_index
is mixed with smp_processor_id(), there could be a situation where Tx
descriptors are produced onto XDP Tx ring, but tail is never bumped -
for example pin a particular queue id to non-matching IRQ line.

Address this problem by ignoring the user ring count setting and always
initialize the xdp_rings array to be of num_possible_cpus() size. Then,
always use the smp_processor_id() as an index to xdp_rings array. This
provides serialization as at given time only a single softirq can run on
a particular CPU.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.

Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.

Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.

Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.

Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.

Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently ice_container_type is scoped only for ice_ethtool.c. Next
commit that will split the ice_ring struct onto Rx/Tx specific ring
structs is going to also modify the type of linked list of rings that is
within ice_ring_container. Therefore, the functions that are taking the
ice_ring_container as an input argument will need to be aware of a ring
type that will be looked up.

Embed ice_container_type within ice_ring_container and initialize it
properly when allocating the q_vectors.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

This field is dead and driver is not making any use of it. Simply remove
it.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Ioana Ciornei says:

====================
dpaa2-eth: add support for IRQ coalescing

This patch set adds support for interrupts coalescing in dpaa2-eth.
The first patches add support for the hardware level configuration of
the IRQ coalescing in the dpio driver, while the ones that touch the
dpaa2-eth driver are responsible for the ethtool user interraction.

With the adaptive IRQ coalescing in place and enabled we have observed
the following changes in interrupt rates on one A72 core @2.2GHz
(LX2160A) while running a Rx TCP flow.  The TCP stream is sent on a
10Gbit link and the only cpu that does Rx is fully utilized.
                                IRQ rate (irqs / sec)
before:   4.59 Gbits/sec                24k
after:    5.67 Gbits/sec                1.3k
====================
Signed-off-by: David S. Miller <davem@davemloft.net>