Add bridge netfilter deferred output hooks to feature-removal-schedule
and disable them by default. Until their removal they will be
activated by the physdev match when needed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Locally generated broadcast and multicast packets have pkttype set to
PACKET_LOOPBACK instead of PACKET_BROADCAST or PACKET_MULTICAST. This
causes the pkttype match to fail to match packets of either type.

The below patch remedies this by using the daddr as a hint as to
broadcast|multicast. While not pretty, this seems like the only way
to solve the problem short of just noting this as a limitation of the
match.

This resolves netfilter bugzilla #484
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of an unknown verdict or NF_STOP the packet leaks. Unknown verdicts
can happen when userspace is buggy. Reinject the packet in case of NF_STOP,
drop on unknown verdicts.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

An RCF message containing a timeout results in a NULL-ptr dereference if
no RRQ has been seen before.

Noticed by the "SATURN tool", reported by Thomas Dillig <tdillig@stanford.edu>
and Isil Dillig <isil@stanford.edu>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_alloc_skb is designated for RX descriptors, not TX.  (Some drivers
use it for the latter anyway, but that's a different story)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

skbuff.h has an #ifndef CONFIG_HAVE_ARCH_DEV_ALLOC_SKB to allow
architectures to reimplement __dev_alloc_skb.  It's not set on any
architecture and now that we have an architecture-overrideable
NET_SKB_PAD there is not point at all to have one either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the queue of the underlying device is stopped at initialization time
or the device is marked "not present", the state will be propagated to the
vlan device and never change. Based on an analysis by Patrick McHardy.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
ACKed-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

It doesn't compile, and it's dubious in several regards:

1) is enabled by non-Kconfig controlled CONFIG_* value
   (noted by Randy Dunlap)
2) XFRM6_TUNNEL_SPI_MAGIC is defined after it's first use
3) the debugging messages print object pointer addresses
   which have no meaning without context

So let's just get rid of it.
Signed-off-by: David S. Miller <davem@davemloft.net>

The Broadcom dongles with HID proxy support actually support SCO over
HCI if the SCO buffer size values are corrected. So instead of disabling
the SCO support, mark this dongle with the quirk for the Bluetooth core
to correct the wrong buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch disables the ISOC transfers for another broken RTX Telecom
based USB dongle. Starting the USB ISOC transfers only ends in a burst
of error messages for invalid SCO packets on connection handle 0.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Belkin F8T012 and F8T013 devices are both based on a Bluetooth chip
from Broadcom and their SCO buffer size values are wrong. The Bluetooth
core should correct these values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The SCO buffer size values on IBM/Lenovo ThinkPad laptops with a
Bluetooth chip from Broadcom are wrong. The USB Bluetooth driver
has to set a quirk to correct the SCO buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some Bluetooth RFCOMM implementations try to negotiate a bigger channel
MTU than we can support for a particular session. The maximum MTU for
a RFCOMM session is limited through the L2CAP layer. So if the other
side proposes a channel MTU that is bigger than the underlying L2CAP
MTU, we should reduce it to the L2CAP MTU of the session minus five
bytes for the RFCOMM headers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In PSCHED_TADD and PSCHED_TADD2, if delta is less than tv.tv_usec (so,
less than USEC_PER_SEC too) then tv_res will be smaller than tv. The
affectation "(tv_res).tv_usec = __delta;" is wrong.  The fix is to
revert to the original code before
4ee303df and change the 'if' in
'while'.

[Shuya MAEDA: "while (__delta >= USEC_PER_SEC){ ... }" instead of
"while (__delta > USEC_PER_SEC){ ... }"]
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using the default sequence window size (100) I got the following in
my logs:

Jun 22 14:24:09 localhost kernel: [ 1492.114775] DCCP: Step 6 failed for
DATA packet, (LSWL(6279674225) <= P.seqno(6279674749) <=
S.SWH(6279674324)) and (P.ackno doesn't exist or LAWL(18798206530) <=
P.ackno(1125899906842620) <= S.AWH(18798206548), sending SYNC...
Jun 22 14:24:09 localhost kernel: [ 1492.115147] DCCP: Step 6 failed for
DATA packet, (LSWL(6279674225) <= P.seqno(6279674750) <=
S.SWH(6279674324)) and (P.ackno doesn't exist or LAWL(18798206530) <=
P.ackno(1125899906842620) <= S.AWH(18798206549), sending SYNC...

I went to alter the default sysctl and it didn't take for new sockets.
Below patch fixes this.

I think the default is too low but it is what the DCCP spec specifies.

As a side effect of this my rx speed using iperf goes from about 2.8 Mbits/sec
to 3.5. This is still far too slow but it is a step in the right direction.

Compile tested only for IPv6 but not particularly complex change.

Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read the max_cmds value from the response to the QUERY_FW command
before printing out the value, so that the real value goes into the
debug output.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The neighbour ha field may get updated without destroying the
neighbour.  In this case, the ha field gets out of sync with the
address handle stored in ipoib_neigh->ah, with the result that
the ah field would point to an incorrect path, resulting in all
packets being lost.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Need to set mcast->ah before debug code dereferences it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Validate MADs sent by userspace clients for spec compliance with
C13-18.1.1 (prevent duplicate requests and responses sent on the
same port).  Without this, RMPP transactions get aborted because
of duplicate packets.

This patch is similar to that provided by Jack Morgenstein.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

ipath_skip_sge() doesn't exactly duplicate the side effects of
ipath_copy_sge() if num_sge > 1 since it doesn't decrement ss->num_sge.
This could result in the sg_list being accessed out of bounds.
Since ipath_skip_sge() is almost always called with num_sge == 1,
the original "optimization" is almost never used.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

I am still working on a proposal to remove the phys_to_virt() calls
in the ib_ipath driver.  In the mean time, this patch allows SRP
to work by fixing the R_Key check and conversion from IB address
to kernel virtual address.  It also returns the correct page size
for FMRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This patch fixes a problem where certain error packets are passed
to the InfiniBand layer for processing even though the packet
actually was received with an error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Mem-free HCAs always keep one spare SRQ WQE, so the SRQ limit cannot
be set beyond srq->max - 1.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Lockdep warns because uverbs is trying to take uobj->mutex when it
already holds that lock.  This is because there are really multiple
types of uobjs even though all of their locks are initialized in
common code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

ib_uverbs_create_ah() and ib_uverbs_create_srq() did not release the
PD's read lock in their error paths, which lead to deadlock when
destroying the PD.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fix ABBA deadlock between lock_cpu_hotplug() and the cpuset
callback_mutex lock.

It only happens on cpu_exclusive cpusets, due to the dynamic
sched domain code trying to take the cpu hotplug lock inside
the cpuset callback_mutex lock.

This bug has apparently been here for several months, but didn't
get hit until the right customer load on a large system.

This fix appears right from inspection, but it will take a few
more days running it on that customers workload to be confident
we nailed it.  We don't have any other reproducible test case.

The cpu_hotplug_lock() tends to cover large runs of code.
The other places that hold both that lock and the cpuset callback
mutex lock always nest the cpuset lock inside the hotplug lock.
This place tries to do the reverse, risking an ABBA deadlock.

This is in the cpuset_rmdir() code, where we:
  * take the callback_mutex lock
  * mark the cpuset CS_REMOVED
  * call update_cpu_domains for cpu_exclusive cpusets
  * in that call, take the cpu_hotplug lock if the
    cpuset is marked for removal.

Thanks to Jack Steiner for identifying this deadlock.

The fix is to tear down the dynamic sched domain before we grab
the cpuset callback_mutex lock.  This way, the two locks are
serialized, with the hotplug lock taken and released before
trying for the cpuset lock.

I suspect that this bug was introduced when I changed the
cpuset locking from one lock to two.  The dynamic sched domain
dependency on cpu_exclusive cpusets and its hotplug hooks were
added to this code earlier, when cpusets had only a single lock.
It may well have been fine then.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The CPU hotplug locking was quite messy, with a recursive lock to
handle the fact that both the actual up/down sequence wanted to
protect itself from being re-entered, but the callbacks that it
called also tended to want to protect themselves from CPU events.

This splits the lock into two (one to serialize the whole hotplug
sequence, the other to protect against the CPU present bitmaps
changing). The latter still allows recursive usage because some
subsystems (ondemand policy for cpufreq at least) had already gotten
too used to the lax locking, but the locking mistakes are hopefully
now less fundamental, and we now warn about recursive lock usage
when we see it, in the hope that it can be fixed.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Shutting down the ondemand policy was fraught with potential
problems, causing issues for SMP suspend (which wants to hot-
unplug) all but the last CPU.

This should fix at least the worst problems (divide-by-zero
and infinite wait for the workqueue to shut down).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
  [TIPC]: Removing useless casts
  [IPV4]: Fix nexthop realm dumping for multipath routes
  [DUMMY]: Avoid an oops when dummy_init_one() failed
  [IFB] After ifb_init_one() failed, i is increased. Decrease
  [NET]: Fix reversed error test in netif_tx_trylock
  [MAINTAINERS]: Mark LAPB as Oprhan.
  [NET]: Conversions from kmalloc+memset to k(z|c)alloc.
  [NET]: sun happymeal, little pci cleanup
  [IrDA]: Use alloc_skb() in IrDA TX path
  [I/OAT]: Remove pci_module_init() from Intel I/OAT DMA engine
  [I/OAT]: net/core/user_dma.c should #include <net/netdma.h>
  [SCTP]: ADDIP: Don't use an address as source until it is ASCONF-ACKed
  [SCTP]: Set chunk->data_accepted only if we are going to accept it.
  [SCTP]: Verify all the paths to a peer via heartbeat before using them.
  [SCTP]: Unhash the endpoint in sctp_endpoint_free().
  [SCTP]: Check for NULL arg to sctp_bucket_destroy().
  [PKT_SCHED] netem: Fix slab corruption with netem (2nd try)
  [WAN]: Converted synclink drivers to use netif_carrier_*()
  [WAN]: Cosmetic changes to N2 and C101 drivers
  [WAN]: Added missing netif_dormant_off() to generic HDLC
  ...

Removing useless casts
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Routing realms exist per nexthop, but are only returned to userspace
for the first nexthop. This is due to the fact that iproute2 only
allows to set the realm for the first nexthop and the kernel refuses
multipath routes where only a single realm is present.

Dump all realms for multipath routes to enable iproute to correctly
display them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It before entering in the loop for freeing the other ifb devices.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

A non-zero return value indicates success from spin_trylock,
not error.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maintainer email not longer exists.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use pci_register_driver instead of pci_module_init. Use PCI_DEVICE macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As pointed out by Christoph Hellwig, dev_alloc_skb() is not intended to be
used for allocating TX sk_buff. The IrDA stack was exclusively calling
dev_alloc_skb() on the TX path, and this patch fixes that.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>