NanoPi M1 is the Allwinner H3 based board.
This patch enables UART for debug console, LEDs, GPIO key switch, 3 USB
host ports, a micro SD slot and related power and pin controls by using
NanoPi common dtsi file.

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

NanoPi common dtsi supports all components of NEO SBC, so just include it.

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch provides a common file for NanoPi M1 and Neo SBC.

Those have common features below.
  * UART0
  * 2 LEDs
  * USB host (EHCI3, OHCI3) and PHY
  * MicroSD
  * GPIO key switch

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The I2C1 and SPI2 buses are exposed on the CHIP headers, and are not
explicitly dedicated to anything.

Add them to the DTS with the muxing already set, but keep them disabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Some boards use the LCD in RGB565. Enable the pin muxing option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

All the sun5i have the SPI2 pins exposed on the PE bank. Add them to the
DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The SPI2 pins on the sun5i PB bank are only available on the A10s. Rename
the A10s only bank so that it doesn't confuse people on the other SoCs
whose indexing would start at b.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The CHIP uses a 1-Wire bus to discover the DIPs. Enable the bus in the DT.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The WiFi chip is powered through a GPIO and two regulators in parallel.
Since that case is not supported yet, just set them as always on before we
rework the regulator framework to deal with those.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The CHIP Pro is a small embeddable board. It features a GR8, an AXP209
PMIC, a 512MB SLC NAND and a WiFi/BT chip.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The UART3 pins were missing from the DTSI. Add them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The UART2 pins were missing from the DTSI. Add them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The PWM controller has two different channels, but only the first pin was
exposed in the DTSI. Add the other one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

There was a dumb copy and paste mistake here, fix it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The GR8 has access to the UART3 controller, which was missing in the
DTSI. Add it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The LCD0 controller on the A31 can do RGB output up to 8 bits per
channel. Add the pins for RGB888 output.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A31 has 2 parallel display pipelines, which can be intermixed.
However the driver currently only supports one of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sun7i-a20-olimex-som-evb.dts doesn't contain cpu-supply needed for
voltage-scaling with cpufreq-dt so define it.
The default voltages are defined in sun7i-a20.dtsi.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we have support for the VGA bridges using our DRM driver, enable
the display engine for the Olimex A13-Olinuxino.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The pinmux setting nodes for the A31 were added out of alphabetical
order. Sort them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

When the patch is applied, the allwinner,driver and allwinner,pull
properties are removed.

Although they're described to be optional in the devicetree binding,
without them, the pinmux cannot be initialized, and the uart cannot
be used.

Add them back to fix the problem, and makes the bluetooth on iNet D978
Rev2 board work.

Fixes: 82eec384 (ARM: dts: sun8i: add pinmux for UART1 at PG)
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pull befs fixes from Luis de Bethencourt:
 "I recently took maintainership of the befs file system [0]. This is
  the first time I send you a git pull request, so please let me know if
  all the below is OK.

  Salah Triki and myself have been cleaning the code and fixing a few
  small bugs.

  Sorry I couldn't send this sooner in the merge window, I was waiting
  to have my GPG key signed by kernel members at ELCE in Berlin a few
  days ago."

[0] https://lkml.org/lkml/2016/7/27/502

* tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs: (39 commits)
  befs: befs: fix style issues in datastream.c
  befs: improve documentation in datastream.c
  befs: fix typos in datastream.c
  befs: fix typos in btree.c
  befs: fix style issues in super.c
  befs: fix comment style
  befs: add check for ag_shift in superblock
  befs: dump inode_size superblock information
  befs: remove unnecessary initialization
  befs: fix typo in befs_sb_info
  befs: add flags field to validate superblock state
  befs: fix typo in befs_find_key
  befs: remove unused BEFS_BT_PARMATCH
  fs: befs: remove ret variable
  fs: befs: remove in vain variable assignment
  fs: befs: remove unnecessary *befs_sb variable
  fs: befs: remove useless initialization to zero
  fs: befs: remove in vain variable assignment
  fs: befs: Insert NULL inode to dentry
  fs: befs: Remove useless calls to brelse in befs_find_brun_dblindirect
  ...

Pull gcc plugins update from Kees Cook:
 "This adds a new gcc plugin named "latent_entropy". It is designed to
  extract as much possible uncertainty from a running system at boot
  time as possible, hoping to capitalize on any possible variation in
  CPU operation (due to runtime data differences, hardware differences,
  SMP ordering, thermal timing variation, cache behavior, etc).

  At the very least, this plugin is a much more comprehensive example
  for how to manipulate kernel code using the gcc plugin internals"

* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  latent_entropy: Mark functions with __latent_entropy
  gcc-plugins: Add latent_entropy plugin

Pull MIPS updates from Ralf Baechle:
 "This is the main MIPS pull request for 4.9:

  MIPS core arch code:
   - traps: 64bit kernels should read CP0_EBase 64bit
   - traps: Convert ebase to KSEG0
   - c-r4k: Drop bc_wback_inv() from icache flush
   - c-r4k: Split user/kernel flush_icache_range()
   - cacheflush: Use __flush_icache_user_range()
   - uprobes: Flush icache via kernel address
   - KVM: Use __local_flush_icache_user_range()
   - c-r4k: Fix flush_icache_range() for EVA
   - Fix -mabi=64 build of vdso.lds
   - VDSO: Drop duplicated -I*/-E* aflags
   - tracing: move insn_has_delay_slot to a shared header
   - tracing: disable uprobe/kprobe on compact branch instructions
   - ptrace: Fix regs_return_value for kernel context
   - Squash lines for simple wrapper functions
   - Move identification of VP(E) into proc.c from smp-mt.c
   - Add definitions of SYNC barrierstype values
   - traps: Ensure full EBase is written
   - tlb-r4k: If there are wired entries, don't use TLBINVF
   - Sanitise coherentio semantics
   - dma-default: Don't check hw_coherentio if device is non-coherent
   - Support per-device DMA coherence
   - Adjust MIPS64 CAC_BASE to reflect Config.K0
   - Support generating Flattened Image Trees (.itb)
   - generic: Introduce generic DT-based board support
   - generic: Convert SEAD-3 to a generic board
   - Enable hardened usercopy
   - Don't specify STACKPROTECTOR in defconfigs

  Octeon:
   - Delete dead code and files across the platform.
   - Change to use all memory into use by default.
   - Rename upper case variables in setup code to lowercase.
   - Delete legacy hack for broken bootloaders.
   - Leave maintaining the link state to the actual ethernet/PHY drivers.
   - Add DTS for D-Link DSR-500N.
   - Fix PCI interrupt routing on D-Link DSR-500N.

  Pistachio:
   - Remove ANDROID_TIMED_OUTPUT from defconfig

  TX39xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  TX49xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  txx9wdt:
   - Add missing clock (un)prepare calls for CCF

  BMIPS:
   - Add PW, GPIO SDHCI and NAND device node names
   - Support APPENDED_DTB
   - Add missing bcm97435svmb to DT_NONE
   - Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
   - Add DT examples for BCM63268, BCM3368 and BCM6362
   - Add support for BCM3368 and BCM6362

  PCI
   - Reduce stack frame usage
   - Use struct list_head lists
   - Support for CONFIG_PCI_DOMAINS_GENERIC
   - Make pcibios_set_cache_line_size an initcall
   - Inline pcibios_assign_all_busses
   - Split pci.c into pci.c & pci-legacy.c
   - Introduce CONFIG_PCI_DRIVERS_LEGACY
   - Support generic drivers

  CPC
   - Convert bare 'unsigned' to 'unsigned int'
   - Avoid lock when MIPS CM >= 3 is present

  GIC:
   - Delete unused file smp-gic.c

  mt7620:
   - Delete unnecessary assignment for the field "owner" from PCI

  BCM63xx:
   - Let clk_disable() return immediately if clk is NULL

  pm-cps:
   - Change FSB workaround to CPU blacklist
   - Update comments on barrier instructions
   - Use MIPS standard lightweight ordering barrier
   - Use MIPS standard completion barrier
   - Remove selection of sync types
   - Add MIPSr6 CPU support
   - Support CM3 changes to Coherence Enable Register

  SMP:
   - Wrap call to mips_cpc_lock_other in mips_cm_lock_other
   - Introduce mechanism for freeing and allocating IPIs

  cpuidle:
   - cpuidle-cps: Enable use with MIPSr6 CPUs.

  SEAD3:
   - Rewrite to use DT and generic kernel feature.

  USB:
   - host: ehci-sead3: Remove SEAD-3 EHCI code

  FBDEV:
   - cobalt_lcdfb: Drop SEAD3 support

  dt-bindings:
   -  Document a binding for simple ASCII LCDs

  auxdisplay:
   - img-ascii-lcd: driver for simple ASCII LCD displays

  irqchip i8259:
   - i8259: Add domain before mapping parent irq
   - i8259: Allow platforms to override poll function
   - i8259: Remove unused i8259A_irq_pending

  Malta:
   - Rewrite to use DT

  of/platform:
   - Probe "isa" busses by default

  CM:
   - Print CM error reports upon bus errors

  Module:
   - Migrate exception table users off module.h and onto extable.h
   - Make various drivers explicitly non-modular:
   - Audit and remove any unnecessary uses of module.h

  mailmap:
   - Canonicalize to Qais' current email address.

  Documentation:
   - MIPS supports HAVE_REGS_AND_STACK_ACCESS_API

  Loongson1C:
   - Add CPU support for Loongson1C
   - Add board support
   - Add defconfig
   - Add RTC support for Loongson1C board

  All this except one Documentation fix has sat in linux-next and has
  survived Imagination's automated build test system"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
  Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
  MIPS: ptrace: Fix regs_return_value for kernel context
  MIPS: VDSO: Drop duplicated -I*/-E* aflags
  MIPS: Fix -mabi=64 build of vdso.lds
  MIPS: Enable hardened usercopy
  MIPS: generic: Convert SEAD-3 to a generic board
  MIPS: generic: Introduce generic DT-based board support
  MIPS: Support generating Flattened Image Trees (.itb)
  MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
  MIPS: Print CM error reports upon bus errors
  MIPS: Support per-device DMA coherence
  MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
  MIPS: Sanitise coherentio semantics
  MIPS: PCI: Support generic drivers
  MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
  MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
  MIPS: PCI: Inline pcibios_assign_all_busses
  MIPS: PCI: Make pcibios_set_cache_line_size an initcall
  MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
  MIPS: PCI: Use struct list_head lists
  ...

Pull sound fixes from Takashi Iwai:
 "Just a few trivial small fixes"

* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: line6: fix a crash in line6_hwdep_write()
  ALSA: seq: fix passing wrong pointer in function call of compatibility layer
  ALSA: hda - Fix a failure of micmute led when having multi adcs
  ALSA: line6: Fix POD X3 Live audio input

Pull more misc uaccess and vfs updates from Al Viro:
 "The rest of the stuff from -next (more uaccess work) + assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  score: traps: Add missing include file to fix build error
  fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
  fs/super.c: fix race between freeze_super() and thaw_super()
  overlayfs: Fix setting IOP_XATTR flag
  iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
  blackfin: no access_ok() for __copy_{to,from}_user()
  arm64: don't zero in __copy_from_user{,_inatomic}
  arm: don't zero in __copy_from_user_inatomic()/__copy_from_user()
  arc: don't leak bits of kernel stack into coredump
  alpha: get rid of tail-zeroing in __copy_user()

Pull cifs fixes from Steve French:
 "Including:

   - nine bug fixes for stable. Some of these we found at the recent two
     weeks of SMB3 test events/plugfests.

   - significant improvements in reconnection (e.g. if server or network
     crashes) especially when mounted with "persistenthandles" or to
     server which advertises Continuous Availability on the share.

   - a new mount option "idsfromsid" which improves POSIX compatibility
     in some cases (when winbind not configured e.g.) by better (and
     faster) fetching uid/gid from acl (when "cifsacl" mount option is
     enabled). NB: we are almost complete work on "cifsacl" (querying
     mode/uid/gid from ACL) for SMB3, but SMB3 support for cifsacl is
     not included in this set.

   - improved handling for SMB3 "credits" (even if server is buggy)

  Still working on two sets of changes:

   - cifsacl enablement for SMB3

   - cleanup of RFC1001 length calculation (so we can handle encryption
     and multichannel and RDMA)

  And a couple of new bugs were reported recently (unrelated to above)
  so will probably have another merge request next week"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
  CIFS: Retrieve uid and gid from special sid if enabled
  CIFS: Add new mount option to set owner uid and gid from special sids in acl
  CIFS: Reset read oplock to NONE if we have mandatory locks after reopen
  CIFS: Fix persistent handles re-opening on reconnect
  SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup
  SMB2: Separate Kerberos authentication from SMB2_sess_setup
  Expose cifs module parameters in sysfs
  Cleanup missing frees on some ioctls
  Enable previous version support
  Do not send SMB3 SET_INFO request if nothing is changing
  SMB3: Add mount parameter to allow user to override max credits
  fs/cifs: reopen persistent handles on reconnect
  Clarify locking of cifs file and tcon structures and make more granular
  Fix regression which breaks DFS mounting
  fs/cifs: keep guid when assigning fid to fileinfo
  SMB3: GUIDs should be constructed as random but valid uuids
  Set previous session id correctly on SMB3 reconnect
  cifs: Limit the overall credit acquired
  Display number of credits available
  Add way to query creation time of file via cifs xattr
  ...

Pull btrfs fixes from Chris Mason:
 "Some fixes from Omar and Dave Sterba for our new free space tree.

  This isn't heavily used yet, but as we move toward making it the new
  default we wanted to nail down an endian bug"

* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: tests: uninline member definitions in free_space_extent
  btrfs: tests: constify free space extent specs
  Btrfs: expand free space tree sanity tests to catch endianness bug
  Btrfs: fix extent buffer bitmap tests on big-endian systems
  Btrfs: catch invalid free space trees
  Btrfs: fix mount -o clear_cache,space_cache=v2
  Btrfs: fix free space tree bitmaps on big-endian systems

score images fail to build as follows.

arch/score/kernel/traps.c: In function 'show_stack':
arch/score/kernel/traps.c:55:3: error:
	implicit declaration of function '__get_user'

__get_user() is declared in asm/uaccess.h, which was previously included
through asm/module.h.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 88dd4a74 ("score: separate extable.h, switch module.h to it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

sb_wait_write()->percpu_rwsem_release() fools lockdep to avoid the
false-positives. Now that xfs was fixed by Dave's commit dbad7c99
("xfs: stop holding ILOCK over filldir callbacks") we can remove it and
change freeze_super() and thaw_super() to run with s_writers.rw_sem locks
held; we add two trivial helpers for that, lockdep_sb_freeze_release()
and lockdep_sb_freeze_acquire().

xfstests-dev/check `grep -il freeze tests/*/???` does not trigger any
warning from lockdep.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull overlayfs updates from Miklos Szeredi:
 "This update contains fixes to the "use mounter's permission to access
  underlying layers" area, and miscellaneous other fixes and cleanups.

  No new features this time"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: use vfs_get_link()
  vfs: add vfs_get_link() helper
  ovl: use generic_readlink
  ovl: explain error values when removing acl from workdir
  ovl: Fix info leak in ovl_lookup_temp()
  ovl: during copy up, switch to mounter's creds early
  ovl: lookup: do getxattr with mounter's permission
  ovl: copy_up_xattr(): use strnlen

Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than
frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which
drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering.

In this case thaw_super() will wrongly call s_op->unfreeze_fs() before
it was actually frozen, and call sb_freeze_unlock() which leads to the
unbalanced percpu_up_write(). Unfortunately lockdep can't detect this,
so this triggers misc BUG_ON()'s in kernel/rcu/sync.c.
Reported-and-tested-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

ovl_fill_super calls ovl_new_inode to create a root inode for the new
superblock before initializing sb->s_xattr.  This wrongly causes
IOP_XATTR to be cleared in i_opflags of the new inode, causing SELinux
to log the following message:

  SELinux: (dev overlay, type overlay) has no xattr support

Fix this by initializing sb->s_xattr and similar fields before calling
ovl_new_inode.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Both import_iovec() and rw_copy_check_uvector() take an array
(typically small and on-stack) which is used to hold an iovec array copy
from userspace. This is to avoid an expensive memory allocation in the
fast path (i.e. few iovec elements).

The caller may have to check whether these functions actually used
the provided buffer or allocated a new one -- but this differs between
the too. Let's just add a kernel doc to clarify what the semantics are
for each function.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>