Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220521111145.81697-36-Julia.Lawall@inria.frSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

thermal/drivers/k3_j72xx_bandgap: Make k3_j72xx_bandgap_j721e_data and k3_j72xx_bandgap_j7200_data static

Fix sparse warnings:

drivers/thermal/k3_j72xx_bandgap.c:532:36: sparse: sparse: symbol 'k3_j72xx_bandgap_j721e_data' was not declared. Should it be static?
drivers/thermal/k3_j72xx_bandgap.c:536:36: sparse: sparse: symbol 'k3_j72xx_bandgap_j7200_data' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jin Xiaoyun <jinxiaoyun2@huawei.com>
Link: https://lore.kernel.org/r/20220613063111.654893-1-jinxiaoyun2@huawei.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

This while loop exits with "i" set to -1 and so then it sets:

	derived_table[-1] = derived_table[0] - 300;

There is no need for this assignment at all.  Just delete it.

Fixes: 72b3fc61c752 ("thermal: k3_j72xx_bandgap: Add the bandgap driver support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YoetjwcOEzYEFp9b@kiliSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

If an error occurs in the k3_j72xx_bandgap_probe() function the memory
allocated to the 'ref_table' will not be released.

Add a err_free_ref_table step to the error path to free 'ref_table'

Fixes: 72b3fc61c752 ("thermal: k3_j72xx_bandgap: Add the bandgap driver support")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20220525213617.30002-1-bb@ti.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The trends DROP_FULL and RAISE_FULL are not used and were never used
in the past AFAICT. Remove these conditions as they seems to not be
handled anywhere.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220629151012.3115773-2-daniel.lezcano@linaro.orgSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The code is actually clampling the next cooling device state using the
lowest and highest states of the thermal instance.

That code can be replaced by the clamp() macro which does exactly the
same. It results in a simpler routine to read.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220629151012.3115773-1-daniel.lezcano@linaro.orgSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The get_trend function relies on the interrupt to set the raising or
dropping trend. However the interpolated temperature is already giving
the temperature information to the thermal framework which is able to
deduce the trend.

Remove the trend code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220616202537.303655-3-daniel.lezcano@linaro.orgSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The get_trend function does already what the generic framework does.

Remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://lore.kernel.org/r/20220616202537.303655-2-daniel.lezcano@linaro.orgSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

There is a get_trend function which is a wrapper to call a private
get_trend function. However, this private get_trend function is not
assigned anywhere.

Remove this dead code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Amit Kucheria <amitk@kernel.org>
Link: https://lore.kernel.org/r/20220616202537.303655-1-daniel.lezcano@linaro.orgSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Add support for R-Car S4. The S4 IP differs a bit from its siblings in
such way that it has 3 out of 4 TSC nodes for Linux and the interrupts
are not routed to the INTC-AP but to the ECM.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220610201701.7946-2-wsa+renesas@sang-engineering.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

When handling the V3U/r8a779a0 exception, avoid using 'not:' because
then its subschemas are far away in the 'else:' branch. Keep them
together using positive logic.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220610201701.7946-1-wsa+renesas@sang-engineering.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Convert the Qualcomm QPNP PMIC Temperature Alarm to DT Schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220608112702.80873-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

When setting up a new board, a plain "Can't register thermal zone"
didn't help me much because the thermal zones in DT were all fine. I
just had a sensor entry too much in the parent TSC node. Reword the
failure/success messages to contain the sensor number to make it easier
to understand which sensor is affected. Example output now:

rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 3: Can't register thermal zone
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20220610200500.6727-1-wsa+renesas@sang-engineering.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Maintainers of the directory Documentation/devicetree/bindings/thermal
are also the maintainers of the corresponding directory
include/dt-bindings/thermal.

Add the file entry for include/dt-bindings/thermal to the appropriate
section in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220613124309.28790-1-lukas.bulwahn@gmail.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Remove unneeded global variable devfreq_cooling_ops which is used only
as a copy pattern. Instead, extend the struct devfreq_cooling_device with
the needed ops structure. This also simplifies the allocation/free code
during the setup/cleanup.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20220613124327.30766-5-lukasz.luba@arm.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The code has moved and left some comments stale. Update them where
there is a need.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20220613124327.30766-4-lukasz.luba@arm.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Simplify the thermal_power_cpu_get_power trace event by removing
complicated cpumask and variable length array. Now the tools parsing trace
output don't have to hassle to get this power data. The simplified format
version uses 'policy->cpu'. Remove also the 'load' information completely
since there is very little value of it in this trace event. To get the
CPUs' load (or utilization) there are other dedicated trace hooks in the
kernel. This patch also simplifies and speeds-up the main cooling code
when that trace event is enabled.

Rename the trace event to avoid confusion of tools which parse the trace
file.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20220613124327.30766-3-lukasz.luba@arm.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

It is very unlikely that one CPU cluster would have the EM and some other
won't have it (because EM registration failed or DT lacks needed entry).
Although, we should avoid modifying global variable with callbacks anyway.
Redesign this and add safety for such situation.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220613124327.30766-2-lukasz.luba@arm.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Add RaptorLake to the list of processor models supported by the Intel
TCC cooling driver.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
[ rjw: Subject edits, new changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add Meteor Lake PCI ID for processor thermal device.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull device properties framework updates from Rafael Wysocki:
 "These mostly extend the device property API and make it easier to use
  in some cases.

  Specifics:

   - Allow error pointer to be passed to fwnode APIs (Andy Shevchenko).

   - Introduce fwnode_for_each_parent_node() (Andy Shevchenko, Douglas
     Anderson).

   - Advertise fwnode and device property count API calls (Andy
     Shevchenko).

   - Clean up fwnode_is_ancestor_of() (Andy Shevchenko).

   - Convert device_{dma_supported,get_dma_attr} to fwnode (Sakari
     Ailus).

   - Release subnode properties with data nodes (Sakari Ailus).

   - Add ->iomap() and ->irq_get() to fwnode operations (Sakari Ailus)"

* tag 'devprop-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  device property: Advertise fwnode and device property count API calls
  device property: Fix recent breakage of fwnode_get_next_parent_dev()
  device property: Drop 'test' prefix in parameters of fwnode_is_ancestor_of()
  device property: Introduce fwnode_for_each_parent_node()
  device property: Allow error pointer to be passed to fwnode APIs
  ACPI: property: Release subnode properties with data nodes
  device property: Add irq_get to fwnode operation
  device property: Add iomap to fwnode operations
  ACPI: property: Move acpi_fwnode_device_get_match_data() up
  device property: Convert device_{dma_supported,get_dma_attr} to fwnode

Pull thermal control updates from Rafael Wysocki:
 "These add a thermal library and thermal tools to wrap the netlink
  interface into event-based callbacks, improve overheat condition
  handling during suspend-to-idle on Intel SoCs, add some new hardware
  support, fix bugs and clean up code.

  Specifics:

   - Add thermal library and thermal tools to encapsulate the netlink
     into event based callbacks (Daniel Lezcano, Jiapeng Chong).

   - Improve overheat condition handling during suspend-to-idle in the
     Intel PCH thermal driver (Zhang Rui).

   - Use local ops instead of global ops in devfreq_cooling (Kant Fan).

   - Clean up _OSC handling in int340x (Davidlohr Bueso).

   - Switch hisi_termal from CONFIG_PM_SLEEP guards to pm_sleep_ptr()
     (Hesham Almatary).

   - Add new k3 j72xx bangdap driver and the corresponding bindings
     (Keerthy).

   - Fix missing of_node_put() in the SC iMX driver at probe time
     (Miaoqian Lin).

   - Fix memory leak in __thermal_cooling_device_register()
     when device_register() fails by calling
     thermal_cooling_device_destroy_sysfs() (Yang Yingliang).

   - Add sc8180x and sc8280xp compatible string in the DT bindings and
     lMH support for QCom tsens driver (Bjorn Andersson).

   - Fix OTP Calibration Register values conforming to the documentation
     on RZ/G2L and bindings documentation for RZ/G2UL (Biju Das).

   - Fix type in kerneldoc description for __thermal_bind_params
     (Corentin Labbe).

   - Fix potential NULL dereference in sr_thermal_probe() on Broadcom
     platform (Zheng Yongjun).

   - Add change mode ops to the thermal-of sensor (Manaf Meethalavalappu
     Pallikunhi).

   - Fix non-negative value support by preventing the value to be clamp
     to zero (Stefan Wahren).

   - Add compatible string and DT bindings for MSM8960 tsens driver
     (Dmitry Baryshkov).

   - Add hwmon support for K3 driver (Massimiliano Minella).

   - Refactor and add multiple generations support for QCom ADC driver
     (Jishnu Prakash).

   - Use platform_get_irq_optional() to get the interrupt on RCar driver
     and document Document RZ/V2L bindings (Lad Prabhakar).

   - Remove NULL check after container_of() call from the Intel HFI
     thermal driver (Haowen Bai)"

* tag 'thermal-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (38 commits)
  thermal: intel: pch: improve the cooling delay log
  thermal: intel: pch: enhance overheat handling
  thermal: intel: pch: move cooling delay to suspend_noirq phase
  PM: wakeup: expose pm_wakeup_pending to modules
  thermal: k3_j72xx_bandgap: Add the bandgap driver support
  dt-bindings: thermal: k3-j72xx: Add VTM bindings documentation
  thermal/drivers/imx_sc_thermal: Fix refcount leak in imx_sc_thermal_probe
  thermal/core: Fix memory leak in __thermal_cooling_device_register()
  dt-bindings: thermal: tsens: Add sc8280xp compatible
  dt-bindings: thermal: lmh: Add Qualcomm sc8180x compatible
  thermal/drivers/qcom/lmh: Add sc8180x compatible
  thermal/drivers/rz2gl: Fix OTP Calibration Register values
  dt-bindings: thermal: rzg2l-thermal: Document RZ/G2UL bindings
  thermal: thermal_of: fix typo on __thermal_bind_params
  tools/thermal: remove unneeded semicolon
  tools/lib/thermal: remove unneeded semicolon
  thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe
  tools/thermal: Add thermal daemon skeleton
  tools/thermal: Add a temperature capture tool
  tools/thermal: Add util library
  ...

Pull power management updates from Rafael Wysocki:
 "These add support for 'artificial' Energy Models in which power
  numbers for different entities may be in different scales, add support
  for some new hardware, fix bugs and clean up code in multiple places.

  Specifics:

   - Update the Energy Model support code to allow the Energy Model to
     be artificial, which means that the power values may not be on a
     uniform scale with other devices providing power information, and
     update the cpufreq_cooling and devfreq_cooling thermal drivers to
     support artificial Energy Models (Lukasz Luba).

   - Make DTPM check the Energy Model type (Lukasz Luba).

   - Fix policy counter decrementation in cpufreq if Energy Model is in
     use (Pierre Gondois).

   - Add CPU-based scaling support to passive devfreq governor (Saravana
     Kannan, Chanwoo Choi).

   - Update the rk3399_dmc devfreq driver (Brian Norris).

   - Export dev_pm_ops instead of suspend() and resume() in the IIO
     chemical scd30 driver (Jonathan Cameron).

   - Add namespace variants of EXPORT[_GPL]_SIMPLE_DEV_PM_OPS and
     PM-runtime counterparts (Jonathan Cameron).

   - Move symbol exports in the IIO chemical scd30 driver into the
     IIO_SCD30 namespace (Jonathan Cameron).

   - Avoid device PM-runtime usage count underflows (Rafael Wysocki).

   - Allow dynamic debug to control printing of PM messages (David
     Cohen).

   - Fix some kernel-doc comments in hibernation code (Yang Li, Haowen
     Bai).

   - Preserve ACPI-table override during hibernation (Amadeusz
     Sławiński).

   - Improve support for suspend-to-RAM for PSCI OSI mode (Ulf Hansson).

   - Make Intel RAPL power capping driver support the RaptorLake and
     AlderLake N processors (Zhang Rui, Sumeet Pawnikar).

   - Remove redundant store to value after multiply in the RAPL power
     capping driver (Colin Ian King).

   - Add AlderLake processor support to the intel_idle driver (Zhang
     Rui).

   - Fix regression leading to no genpd governor in the PSCI cpuidle
     driver and fix the riscv-sbi cpuidle driver to allow a genpd
     governor to be used (Ulf Hansson).

   - Fix cpufreq governor clean up code to avoid using kfree() directly
     to free kobject-based items (Kevin Hao).

   - Prepare cpufreq for powerpc's asm/prom.h cleanup (Christophe
     Leroy).

   - Make intel_pstate notify frequency invariance code when no_turbo is
     turned on and off (Chen Yu).

   - Add Sapphire Rapids OOB mode support to intel_pstate (Srinivas
     Pandruvada).

   - Make cpufreq avoid unnecessary frequency updates due to mismatch
     between hardware and the frequency table (Viresh Kumar).

   - Make remove_cpu_dev_symlink() clear the real_cpus mask to simplify
     code (Viresh Kumar).

   - Rearrange cpufreq_offline() and cpufreq_remove_dev() to make the
     calling convention for some driver callbacks consistent (Rafael
     Wysocki).

   - Avoid accessing half-initialized cpufreq policies from the show()
     and store() sysfs functions (Schspa Shi).

   - Rearrange cpufreq_offline() to make the calling convention for some
     driver callbacks consistent (Schspa Shi).

   - Update CPPC handling in cpufreq (Pierre Gondois).

   - Extend dev_pm_domain_detach() doc (Krzysztof Kozlowski).

   - Move genpd's time-accounting to ktime_get_mono_fast_ns() (Ulf
     Hansson).

   - Improve the way genpd deals with its governors (Ulf Hansson).

   - Update the turbostat utility to version 2022.04.16 (Len Brown, Dan
     Merillat, Sumeet Pawnikar, Zephaniah E. Loss-Cutler-Hull, Chen Yu)"

* tag 'pm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (94 commits)
  PM: domains: Trust domain-idle-states from DT to be correct by genpd
  PM: domains: Measure power-on/off latencies in genpd based on a governor
  PM: domains: Allocate governor data dynamically based on a genpd governor
  PM: domains: Clean up some code in pm_genpd_init() and genpd_remove()
  PM: domains: Fix initialization of genpd's next_wakeup
  PM: domains: Fixup QoS latency measurements for IRQ safe devices in genpd
  PM: domains: Measure suspend/resume latencies in genpd based on governor
  PM: domains: Move the next_wakeup variable into the struct gpd_timing_data
  PM: domains: Allocate gpd_timing_data dynamically based on governor
  PM: domains: Skip another warning in irq_safe_dev_in_sleep_domain()
  PM: domains: Rename irq_safe_dev_in_no_sleep_domain() in genpd
  PM: domains: Don't check PM_QOS_FLAG_NO_POWER_OFF in genpd
  PM: domains: Drop redundant code for genpd always-on governor
  PM: domains: Add GENPD_FLAG_RPM_ALWAYS_ON for the always-on governor
  powercap: intel_rapl: remove redundant store to value after multiply
  cpufreq: CPPC: Enable dvfs_possible_from_any_cpu
  cpufreq: CPPC: Enable fast_switch
  ACPI: CPPC: Assume no transition latency if no PCCT
  ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
  ACPI: CPPC: Check _OSC for flexible address space
  ...

Pull ACPI updates from Rafael Wysocki:
 "These update the ACPICA kernel code to upstream revision 20220331,
  improve handling of PCI devices that are in D3cold during system
  initialization, add support for a few features, fix bugs and clean up
  code.

  Specifics:

   - Update ACPICA code in the kernel to upstream revision 20220331
     including the following changes:
       - Add support for the Windows 11 _OSI string (Mario Limonciello)
       - Add the CFMWS subtable to the CEDT table (Lawrence Hileman).
       - iASL: NHLT: Treat Terminator as specific_config (Piotr
         Maziarz).
       - iASL: NHLT: Fix parsing undocumented bytes at the end of
         Endpoint Descriptor (Piotr Maziarz).
       - iASL: NHLT: Rename linux specific strucures to device_info
         (Piotr Maziarz).
       - Add new ACPI 6.4 semantics to Load() and LoadTable() (Bob
         Moore).
       - Clean up double word in comment (Tom Rix).
       - Update copyright notices to the year 2022 (Bob Moore).
       - Remove some tabs and // comments - automated cleanup (Bob
         Moore).
       - Replace zero-length array with flexible-array member (Gustavo
         A. R. Silva).
       - Interpreter: Add units to time variable names (Paul Menzel).
       - Add support for ARM Performance Monitoring Unit Table (Besar
         Wicaksono).
       - Inform users about ACPI spec violation related to sleep length
         (Paul Menzel).
       - iASL/MADT: Add OEM-defined subtable (Bob Moore).
       - Interpreter: Fix some typo mistakes (Selvarasu Ganesan).
       - Updates for revision E.d of IORT (Shameer Kolothum).
       - Use ACPI_FORMAT_UINT64 for 64-bit output (Bob Moore).

   - Improve debug messages in the ACPI device PM code (Rafael Wysocki).

   - Block ASUS B1400CEAE from suspend to idle by default (Mario
     Limonciello).

   - Improve handling of PCI devices that are in D3cold during system
     initialization (Rafael Wysocki).

   - Fix BERT error region memory mapping (Lorenzo Pieralisi).

   - Add support for NVIDIA 16550-compatible port subtype to the SPCR
     parsing code (Jeff Brasen).

   - Use static for BGRT_SHOW kobj_attribute defines (Tom Rix).

   - Fix missing prototype warning for acpi_agdi_init() (Ilkka
     Koskinen).

   - Fix missing ERST record ID in the APEI code (Liu Xinpeng).

   - Make APEI error injection to refuse to inject into the zero page
     (Tony Luck).

   - Correct description of INT3407 / INT3532 DPTF attributes in sysfs
     (Sumeet Pawnikar).

   - Add support for high frequency impedance notification to the DPTF
     driver (Sumeet Pawnikar).

   - Make mp_config_acpi_gsi() a void function (Li kunyu).

   - Unify Package () representation for properties in the ACPI device
     properties documentation (Andy Shevchenko).

   - Include UUID in _DSM evaluation warning (Michael Niewöhner)"

* tag 'acpi-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (41 commits)
  Revert "ACPICA: executer/exsystem: Warn about sleeps greater than 10 ms"
  ACPI: utils: include UUID in _DSM evaluation warning
  ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default
  x86: ACPI: Make mp_config_acpi_gsi() a void function
  ACPI: DPTF: Add support for high frequency impedance notification
  ACPI: AGDI: Fix missing prototype warning for acpi_agdi_init()
  ACPI: bus: Avoid non-ACPI device objects in walks over children
  ACPI: DPTF: Correct description of INT3407 / INT3532 attributes
  ACPI: BGRT: use static for BGRT_SHOW kobj_attribute defines
  ACPI, APEI, EINJ: Refuse to inject into the zero page
  ACPI: PM: Always print final debug message in acpi_device_set_power()
  ACPI: SPCR: Add support for NVIDIA 16550-compatible port subtype
  ACPI: docs: enumeration: Unify Package () for properties (part 2)
  ACPI: APEI: Fix missing ERST record id
  ACPICA: Update version to 20220331
  ACPICA: exsystem.c: Use ACPI_FORMAT_UINT64 for 64-bit output
  ACPICA: IORT: Updates for revision E.d
  ACPICA: executer/exsystem: Fix some typo mistakes
  ACPICA: iASL/MADT: Add OEM-defined subtable
  ACPICA: executer/exsystem: Warn about sleeps greater than 10 ms
  ...

Pull HID updates from Jiri Kosina:

 - support for pens with 3 buttons with Wacom driver (Joshua Dickens)

 - support for HID_DG_SCANTIME to report the timestamp for pen and touch
   events in Wacom driver (Joshua Dickens)

 - support for sensor discovery in amd-sfh driver (Basavaraj Natikar)

 - support for wider variety of Huion tablets ported from DIGImend
   project (José Expósito, Nikolai Kondrashov)

 - new device IDs and other assorted small code cleanups

* tag 'for-linus-2022052401' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (44 commits)
  HID: apple: Properly handle function keys on Keychron keyboards
  HID: uclogic: Switch to Digitizer usage for styluses
  HID: uclogic: Add pen support for XP-PEN Star 06
  HID: uclogic: Differentiate touch ring and touch strip
  HID: uclogic: Always shift touch reports to zero
  HID: uclogic: Do not focus on touch ring only
  HID: uclogic: Return raw parameters from v2 pen init
  HID: uclogic: Move param printing to a function
  HID: core: Display "SENSOR HUB" for sensor hub bus string in hid_info
  HID: amd_sfh: Move bus declaration outside of amd-sfh
  HID: amd_sfh: Add physical location to HID device
  HID: amd_sfh: Modify the hid name
  HID: amd_sfh: Modify the bus name
  HID: amd_sfh: Add sensor name by index for debug info
  HID: amd_sfh: Add support for sensor discovery
  HID: bigben: fix slab-out-of-bounds Write in bigben_probe
  Hid: wacom: Fix kernel test robot warning
  HID: uclogic: Disable pen usage for Huion keyboard interfaces
  HID: uclogic: Support disabling pen usage
  HID: uclogic: Pass keyboard reports as is
  ...

Pull spi updates from Mark Brown:
 "This is quite a quiet release but some new drivers mean that the
  diffstat is fairly large. The new drivers include the aspeed driver
  which is migrated from MTD as part of the ongoing move of controllers
  with specialised support for SPI flashes into the SPI subsystem.

   - Support for devices which flip CPHA during recieve only transfers
     (eg, if MOSI and MISO have inverted polarity).

   - Overhaul of the i.MX driver, including the addition of PIO support
     for better performance on small transfers.

   - Migration of the Aspeed driver from MTD.

   - Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
     IPM and SFI"

* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
  spi: spi-au1550: replace ternary operator with min()
  mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
  spi: aspeed: Calibrate read timings
  spi: aspeed: Add support for the AST2400 SPI controller
  spi: aspeed: Workaround AST2500 limitations
  spi: aspeed: Adjust direct mapping to device size
  spi: aspeed: Add support for direct mapping
  spi: spi-mem: Convert Aspeed SMC driver to spi-mem
  spi: Convert the Aspeed SMC controllers device tree binding
  spi: spi-cadence: Update ISR status variable type to irqreturn_t
  spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
  spi: cadence-quadspi: Handle spi_unregister_master() in remove()
  spi: stm32-qspi: Remove SR_BUSY bit check before sending command
  spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
  spi: stm32-qspi: Fix wait_cmd timeout in APM mode
  spi: cadence-quadspi: remove unnecessary (void *) casts
  spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
  spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
  spi: spi-imx: add PIO polling support
  spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
  ...

Pull regulator updates from Mark Brown:
 "This is mostly a drivers update including a couple of new drivers but
  we do have some fixes and improvements to the core as well.

   - Make sure we don't log spuriously about uncontrollable regulators.

   - Don't use delays when we should use sleeps for regulators with
     larger ramp times.

   - Support for MediaTek MT6358 and MT6366, Richtek RT5759 and Silicon
     Mitus SM5703"

* tag 'regulator-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
  regulator: scmi: Fix refcount leak in scmi_regulator_probe
  regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
  regulator: qcom_smd: Fix up PM8950 regulator configuration
  regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
  regulator: core: Add error flags to sysfs attributes
  regulator: dt-bindings: qcom,rpmh: document vdd-l7-bob-supply on PMR735A
  regulator: dt-bindings: qcom,rpmh: document supplies per variant
  regulator: dt-bindings: qcom,rpmh: update maintainers
  regulator: mt6315: Enforce regulator-compatible, not name
  regulator: pca9450: Enable DVS control via PMIC_STBY_REQ
  regulator: pca9450: Make warm reset on WDOG_B assertion
  regulator: Add property for WDOG_B warm reset
  regulator: pca9450: Make I2C Level Translator configurable
  regulator: Add property for I2C level shifter
  regulator: sm5703: Correct reference to the common regulator schema
  regulator: sm5703-regulator: Add regulators support for SM5703 MFD
  dt-bindings: regulator: Add bindings for Silicon Mitus SM5703 regulators
  regulator: richtek,rt4801: parse GPIOs per regulator
  regulator: dt-bindings: richtek,rt4801: use existing ena_gpiod feature
  regulator: core: Sleep (not delay) in set_voltage()
  ...

Pull regmap updates from Mark Brown:
 "The main change here is Marek's addition of bulk read/write callbacks
  for individual regmaps, we've supported single register operations for
  a while but there's enough hardware out there which can use bulk
  equivalents to make it worthwhile"

* tag 'regmap-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Add missing map->bus check
  regmap: Add bulk read/write callbacks into regmap_config
  regmap: cache: set max_register with reg_stride
  regmap: Constify static regmap_bus structs

Pull MMC updates from Ulf Hansson:
 "MMC core:

   - Support zero-out using TRIM for eMMC

   - Allow to override the busy-timeout for the ioctl-cmds

  MMC host:

   - Continued the conversion of DT bindings into the JSON schema

   - jz4740: Apply DMA engine limits to maximum segment size

   - mmci_stm32: Use a buffer for unaligned DMA requests

   - mmc_spi: Enabled high-speed modes via parsing of DT

   - omap: Make clock management to be compliant with CCF

   - renesas_sdhi:
      - Support eMMC HS400 mode for R-Car V3H ES2.0
      - Don't allow support for eMMC HS400 for R-Car V3M/D3

   - sdhci_am654: Fix problem when SD card slot lacks the card detect
     line

   - sdhci-esdhc-imx: Add support for the imx8dxl variant

   - sdhci-brcmstb: Enable support for clock gating to save power

   - sdhci-msm:
      - Add support for the sdx65 variant
      - Add support for the sm8150 variant

   - sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant

   - sdhci-pci-gli: Add workaround to allow GL9755 to enter ASPM L1.2"

* tag 'mmc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
  mmc: sdhci-of-arasan: Add NULL check for data field
  mmc: core: Support zeroout using TRIM for eMMC
  mmc: sdhci-brcmstb: Fix compiler warning
  mmc: sdhci-msm: Add compatible string check for sdx65
  dt-bindings: mmc: sdhci-msm: Document the SDX65 compatible
  mmc: sdhci-msm: Add compatible string check for sm8150
  dt-bindings: mmc: sdhci-msm: Add compatible string for sm8150
  mmc: sdhci-msm: Add SoC specific compatibles
  dt-bindings: mmc: sdhci-msm: Convert bindings to yaml
  dt-bindings: mmc: brcm,sdhci-brcmstb: cleanup example
  dt-bindings: mmc: brcm,sdhci-brcmstb: correct number of reg entries
  mmc: sdhci-brcmstb: Enable Clock Gating to save power
  mmc: sdhci-brcmstb: Re-organize flags
  mmc: mmci: Remove custom ios handler
  mmc: atmel-mci: Simplify if(chan) and if(!chan)
  mmc: core: use kobj_to_dev()
  dt-bindings: mmc: sdhci-of-dwcmhsc: Add rk3588
  mmc: core: Add CIDs for cards to the entropy pool
  mmc: core: Allows to override the timeout value for ioctl() path
  mmc: sdhci-omap: Use of_device_get_match_data() helper
  ...

Pull IPMI update from Corey Minyard:
 "Add limits on the number of users and messages, plus sysfs interfaces
  to control those limits.

  Other than that, little cleanups, use dev_xxx() insted of pr_xxx(),
  create initializers for structures, fix a refcount leak, etc"

* tag 'for-linus-4.19-1' of https://github.com/cminyard/linux-ipmi:
  ipmi:ipmb: Fix refcount leak in ipmi_ipmb_probe
  ipmi: remove unnecessary type castings
  ipmi: Make two logs unique
  ipmi:si: Convert pr_debug() to dev_dbg()
  ipmi: Convert pr_debug() to dev_dbg()
  ipmi: Fix pr_fmt to avoid compilation issues
  ipmi: Add an intializer for ipmi_recv_msg struct
  ipmi: Add an intializer for ipmi_smi_msg struct
  ipmi:ssif: Check for NULL msg when handling events and messages
  ipmi: use simple i2c probe function
  ipmi: Add a sysfs count of total outstanding messages for an interface
  ipmi: Add a sysfs interface to view the number of users
  ipmi: Limit the number of message a user may have outstanding
  ipmi: Add a limit on the number of users that may use IPMI

Pull mtd updates from Miquel Raynal:
 "MTD core changes:
   - Call of_platform_populate() for MTD partitions
   - Check devicetree alias for index
   - mtdoops:
      - Add a timestamp to the mtdoops header.
      - Create a header structure for the saved mtdoops.
      - Fix the size of the header read buffer.
   - mtdblock: Warn if opened on NAND
   - Bindings:
      - reserved-memory: Support MTD/block device
      - jedec,spi-nor: remove unneeded properties
      - Extend fixed-partitions binding
      - Add Sercomm (Suzhou) Corporation vendor prefix

  MTD driver changes:
   - st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
   - phram:
      - Allow cached mappings
      - Allow probing via reserved-memory
   - maps: ixp4xx: Drop driver
   - bcm47xxpart: Print correct offset on read error

  CFI driver changes:
   - Rename chip_ready variables
   - Add S29GL064N ID definition
   - Use chip_ready() for write on S29GL064N
   - Move and rename chip_check/chip_ready/chip_good_for_write

  NAND core changes:
   - Print offset instead of page number for bad blocks

  Raw NAND controller drivers:
   - Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
   - CS553X: simplify the return expression of cs553x_write_ctrl_byte()
   - Davinci: Remove redundant unsigned comparison to zero
   - Denali: Use managed device resources
   - GPMI:
      - Add large oob bch setting support
      - Rename the variable ecc_chunk_size
      - Uninline the gpmi_check_ecc function
      - Add strict ecc strength check
      - Refactor BCH geometry settings function
   - Intel: Fix possible null-ptr-deref in ebu_nand_probe()
   - MPC5121: Check before clk_disable_unprepare() not needed
   - Mtk:
      - MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
      - Also parse the default nand-ecc-engine property if available
      - Make mtk_ecc.c a separated module
   - OMAP ELM:
      - Convert the bindings to yaml
      - Describe the bindings for AM64 ELM
      - Add support for its compatible
   - Renesas: Use runtime PM instead of the raw clock API and update the
     bindings accordingly
   - Rockchip: Check before clk_disable_unprepare() not needed
   - TMIO: Check return value after calling platform_get_resource()

  Raw NAND chip driver:
   - Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00

  SPI-NAND chip drivers:
   - Gigadevice:
      - Add support for:
         - GD5FxGM7xExxG
         - GD5F{2,4}GQ5xExxG
         - GD5F1GQ5RExxG
         - GD5FxGQ4xExxG
      - Fix Quad IO for GD5F1GQ5UExxG
   - XTX: Add support for XT26G0xA

  SPI NOR core changes:
   - Read back written SR value to make sure the write was done
     correctly.
   - Introduce a common function for Read ID that manufacturer drivers
     can use to verify the Octal DTR switch worked correctly.
   - Add helpers for read/write any register commands so manufacturer
     drivers don't open code it every time.
   - Clarify rdsr dummy cycles documentation.
   - Add debugfs entry to expose internal flash parameters and state.

  SPI NOR manufacturer drivers changes:
   - Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
   - Move spi_nor_write_ear() to Winbond module since only Winbond
     flashes use it.
   - Rework Micron and Cypress Octal DTR enable methods to improve
     readability.
   - Use the common Read ID function to verify switch to Octal DTR mode
     for Micron and Cypress flashes.
   - Skip polling status on volatile register writes for Micron and
     Cypress flashes since the operation is instant"

* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
  mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
  dt-bindings: mtd: partitions: Extend fixed-partitions binding
  dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
  mtd: phram: Allow cached mappings
  mtd: call of_platform_populate() for MTD partitions
  mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
  dt-bindings: mtd: renesas: Fix the NAND controller description
  mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
  mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
  mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
  mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
  mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
  mtd: spi-nor: debugfs: fix format specifier
  mtd: spi-nor: support eon en25qh256a variant
  mtd: spi-nor: winbond: add support for W25Q512NW-IM
  mtd: spi-nor: expose internal parameters via debugfs
  mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
  mtd: spi-nor: move spi_nor_write_ear() to winbond module
  mtd: spi-nor: amend the rdsr dummy cycles documentation
  mtd: cfi_cmdset_0002: Rename chip_ready variables
  ...

Merge tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "New drivers:

   - Driver for the Microchip LAN966x SoC

   - PMBus driver for Infineon Digital Multi-phase xdp152 family
     controllers

  Chip support added to existing drivers:

   - asus-ec-sensors:
      - Support for ROG STRIX X570-E GAMING WIFI II, PRIME X470-PRO, and
        ProArt X570 Creator WIFI
      - External temperature sensor support for ASUS WS X570-ACE

   - nct6775:
      - Support for I2C driver
      - Support for ASUS PRO H410T / PRIME H410M-R /
        ROG X570-E GAMING WIFI II

   - lm75:
      - Support for - Atmel AT30TS74

   - pmbus/max16601:
      - Support for MAX16602

   - aquacomputer_d5next:
      - Support for Aquacomputer Farbwerk
      - Support for Aquacomputer Octo

   - jc42:
      - Support for S-34TS04A

  Kernel API changes / clarifications:

   - The chip parameter of with_info API is now mandatory

   - New hwmon_device_register_for_thermal API call for use by the
     thermal subsystem

  Improvements:

   - PMBus and JC42 drivers now register with thermal subsystem

   - PMBus drivers now support get_voltage/set_voltage power operations

   - The adt7475 driver now supports pin configuration

   - The lm90 driver now supports setting extended range temperatures
     configuration with a devicetree property

   - The dell-smm driver now registers as cooling device

   - The OCC driver delays hwmon registration until requested by
     userspace

  ... and various other minor fixes and improvements"

* tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (71 commits)
  hwmon: (aquacomputer_d5next) Fix an error handling path in aqc_probe()
  hwmon: (sl28cpld) Fix typo in comment
  hwmon: (pmbus) Check PEC support before reading other registers
  hwmon: (dimmtemp) Fix bitmap handling
  hwmon: (lm90) enable extended range according to DTS node
  dt-bindings: hwmon: lm90: add ti,extended-range-enable property
  dt-bindings: hwmon: lm90: add missing ti,tmp461
  hwmon: (ibmaem) Directly use ida_alloc()/free()
  hwmon: Directly use ida_alloc()/free()
  hwmon: (asus-ec-sensors) fix Formula VIII definition
  dt-bindings: trivial-devices: Add xdp152
  hwmon: (sl28cpld-hwmon) Use HWMON_CHANNEL_INFO macro
  hwmon: (pwm-fan) Use HWMON_CHANNEL_INFO macro
  hwmon: (peci/dimmtemp) Use HWMON_CHANNEL_INFO macro
  hwmon: (peci/cputemp) Use HWMON_CHANNEL_INFO macro
  hwmon: (mr75203) Use HWMON_CHANNEL_INFO macro
  hwmon: (ltc2992) Use HWMON_CHANNEL_INFO macro
  hwmon: (as370-hwmon) Use HWMON_CHANNEL_INFO macro
  hwmon: Make chip parameter for with_info API mandatory
  thermal/drivers/thermal_hwmon: Use hwmon_device_register_for_thermal()
  ...

Pull IMA updates from Mimi Zohar:
 "New is IMA support for including fs-verity file digests and signatures
  in the IMA measurement list as well as verifying the fs-verity file
  digest based signatures, both based on policy.

  In addition, are two bug fixes:

   - avoid reading UEFI variables, which cause a page fault, on Apple
     Macs with T2 chips.

   - remove the original "ima" template Kconfig option to address a boot
     command line ordering issue.

  The rest is a mixture of code/documentation cleanup"

* tag 'integrity-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
  integrity: Fix sparse warnings in keyring_handler
  evm: Clean up some variables
  evm: Return INTEGRITY_PASS for enum integrity_status value '0'
  efi: Do not import certificates from UEFI Secure Boot for T2 Macs
  fsverity: update the documentation
  ima: support fs-verity file digest based version 3 signatures
  ima: permit fsverity's file digests in the IMA measurement list
  ima: define a new template field named 'd-ngv2' and templates
  fs-verity: define a function to return the integrity protected file digest
  ima: use IMA default hash algorithm for integrity violations
  ima: fix 'd-ng' comments and documentation
  ima: remove the IMA_TEMPLATE Kconfig option
  ima: remove redundant initialization of pointer 'file'.

Merge tag 'tpmdd-next-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd

Pull tpm updates from Jarkko Sakkinen:

 - Tightened validation of key hashes for SYSTEM_BLACKLIST_HASH_LIST. An
   invalid hash format causes a compilation error. Previously, they got
   included to the kernel binary but were silently ignored at run-time.

 - Allow root user to append new hashes to the blacklist keyring.

 - Trusted keys backed with Cryptographic Acceleration and Assurance
   Module (CAAM), which part of some of the new NXP's SoC's. Now there
   is total three hardware backends for trusted keys: TPM, ARM TEE and
   CAAM.

 - A scattered set of fixes and small improvements for the TPM driver.

* tag 'tpmdd-next-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
  MAINTAINERS: add KEYS-TRUSTED-CAAM
  doc: trusted-encrypted: describe new CAAM trust source
  KEYS: trusted: Introduce support for NXP CAAM-based trusted keys
  crypto: caam - add in-kernel interface for blob generator
  crypto: caam - determine whether CAAM supports blob encap/decap
  KEYS: trusted: allow use of kernel RNG for key material
  KEYS: trusted: allow use of TEE as backend without TCG_TPM support
  tpm: Add field upgrade mode support for Infineon TPM2 modules
  tpm: Fix buffer access in tpm2_get_tpm_pt()
  char: tpm: cr50_i2c: Suppress duplicated error message in .remove()
  tpm: cr50: Add new device/vendor ID 0x504a6666
  tpm: Remove read16/read32/write32 calls from tpm_tis_phy_ops
  tpm: ibmvtpm: Correct the return value in tpm_ibmvtpm_probe()
  tpm/tpm_ftpm_tee: Return true/false (not 1/0) from bool functions
  certs: Explain the rationale to call panic()
  certs: Allow root user to append signed hashes to the blacklist keyring
  certs: Check that builtin blacklist hashes are valid
  certs: Make blacklist_vet_description() more strict
  certs: Factor out the blacklist hash creation
  tools/certs: Add print-cert-tbs-hash.sh

Pull smack update from Casey Schaufler:
 "A single change to remove a pointless assignment"

* tag 'Smack-for-5.19' of https://github.com/cschaufler/smack-next:
  smack: Remove redundant assignments

Pull Landlock updates from Mickaël Salaün:

 - improve the path_rename LSM hook implementations for RENAME_EXCHANGE;

 - fix a too-restrictive filesystem control for a rare corner case;

 - set the nested sandbox limitation to 16 layers;

 - add a new LANDLOCK_ACCESS_FS_REFER access right to properly handle
   file reparenting (i.e. full rename and link support);

 - add new tests and documentation;

 - format code with clang-format to make it easier to maintain and
   contribute.

* tag 'landlock-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux: (30 commits)
  landlock: Explain how to support Landlock
  landlock: Add design choices documentation for filesystem access rights
  landlock: Document good practices about filesystem policies
  landlock: Document LANDLOCK_ACCESS_FS_REFER and ABI versioning
  samples/landlock: Add support for file reparenting
  selftests/landlock: Add 11 new test suites dedicated to file reparenting
  landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER
  LSM: Remove double path_rename hook calls for RENAME_EXCHANGE
  landlock: Move filesystem helpers and add a new one
  landlock: Fix same-layer rule unions
  landlock: Create find_rule() from unmask_layers()
  landlock: Reduce the maximum number of layers to 16
  landlock: Define access_mask_t to enforce a consistent access mask size
  selftests/landlock: Test landlock_create_ruleset(2) argument check ordering
  landlock: Change landlock_restrict_self(2) check ordering
  landlock: Change landlock_add_rule(2) argument check ordering
  selftests/landlock: Add tests for O_PATH
  selftests/landlock: Fully test file rename with "remove" access
  selftests/landlock: Extend access right tests to directories
  selftests/landlock: Add tests for unknown access rights
  ...

Pull selinux updates from Paul Moore:
 "We've got twelve patches queued for v5.19, with most being fairly
  minor. The highlights are below:

   - The checkreqprot and runtime disable knobs have been deprecated for
     some time with no active users that we can find. In an effort to
     move things along we are adding a pause when the knobs are used to
     help make the deprecation more noticeable in case anyone is still
     using these hacks in the shadows.

   - We've added the anonymous inode class name to the AVC audit records
     when anonymous inodes are involved. This should make writing policy
     easier when anonymous inodes are involved.

   - More constification work. This is fairly straightforward and the
     source of most of the diffstat.

   - The usual minor cleanups: remove unnecessary assignments, assorted
     style/checkpatch fixes, kdoc fixes, macro while-loop
     encapsulations, #include tweaks, etc"

* tag 'selinux-pr-20220523' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  security: declare member holding string literal const
  selinux: log anon inode class name
  selinux: declare data arrays const
  selinux: fix indentation level of mls_ops block
  selinux: include necessary headers in headers
  selinux: avoid extra semicolon
  selinux: update parameter documentation
  selinux: resolve checkpatch errors
  selinux: don't sleep when CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE is true
  selinux: checkreqprot is deprecated, add some ssleep() discomfort
  selinux: runtime disable is deprecated, add some ssleep() discomfort
  selinux: Remove redundant assignments

Pull execve updates from Kees Cook:

 - Fix binfmt_flat GOT handling for riscv (Niklas Cassel)

 - Remove unused/broken binfmt_flat shared library and coredump code
   (Eric W. Biederman)

* tag 'execve-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  binfmt_flat: Remove shared library support
  binfmt_flat: Drop vestiges of coredump support
  binfmt_flat: do not stop relocating GOT entries prematurely on riscv

Pull seccomp updates from Kees Cook:

 - Rework USER_NOTIF notification ordering and kill logic (Sargun
   Dhillon)

 - Improved PTRACE_O_SUSPEND_SECCOMP selftest (Jann Horn)

 - Gracefully handle failed unshare() in selftests (Yang Guang)

 - Spelling fix (Colin Ian King)

* tag 'seccomp-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  selftests/seccomp: Fix spelling mistake "Coud" -> "Could"
  selftests/seccomp: Add test for wait killable notifier
  selftests/seccomp: Refactor get_proc_stat to split out file reading code
  seccomp: Add wait_killable semantic to seccomp user notifier
  selftests/seccomp: Ensure that notifications come in FIFO order
  seccomp: Use FIFO semantics to order notifications
  selftests/seccomp: Add SKIP for failed unshare()
  selftests/seccomp: Test PTRACE_O_SUSPEND_SECCOMP without CAP_SYS_ADMIN

Pull kernel hardening updates from Kees Cook:

 - usercopy hardening expanded to check other allocation types (Matthew
   Wilcox, Yuanzheng Song)

 - arm64 stackleak behavioral improvements (Mark Rutland)

 - arm64 CFI code gen improvement (Sami Tolvanen)

 - LoadPin LSM block dev API adjustment (Christoph Hellwig)

 - Clang randstruct support (Bill Wendling, Kees Cook)

* tag 'kernel-hardening-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (34 commits)
  loadpin: stop using bdevname
  mm: usercopy: move the virt_addr_valid() below the is_vmalloc_addr()
  gcc-plugins: randstruct: Remove cast exception handling
  af_unix: Silence randstruct GCC plugin warning
  niu: Silence randstruct warnings
  big_keys: Use struct for internal payload
  gcc-plugins: Change all version strings match kernel
  randomize_kstack: Improve docs on requirements/rationale
  lkdtm/stackleak: fix CONFIG_GCC_PLUGIN_STACKLEAK=n
  arm64: entry: use stackleak_erase_on_task_stack()
  stackleak: add on/off stack variants
  lkdtm/stackleak: check stack boundaries
  lkdtm/stackleak: prevent unexpected stack usage
  lkdtm/stackleak: rework boundary management
  lkdtm/stackleak: avoid spurious failure
  stackleak: rework poison scanning
  stackleak: rework stack high bound handling
  stackleak: clarify variable names
  stackleak: rework stack low bound handling
  stackleak: remove redundant check
  ...