The 82574 specification update errata 12 states that interrupts may be
missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by
setting all bits related to events that can trigger the Other interrupt in
IMS.

The Other interrupt is raised for such events regardless of whether or not
they are set in IMS. However, only when they are set is the INT_ASSERTED
bit also set in ICR.

By doing this, we ensure that INT_ASSERTED is always set when we read ICR
in e1000_msix_other() and steer clear of the errata. This also ensures that
ICR will automatically be cleared on read, therefore we no longer need to
clear bits explicitly.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).

This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.

Fixes: 4aea7a5c ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This partially reverts commit 4aea7a5c.

We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.

Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".

Link: https://www.spinics.net/lists/netdev/msg480675.htmlSigned-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.

Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).

Fixes: 4aea7a5c ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Stephen Hemminger says:

====================
hv_netvsc: minor fixes

These are improvements to netvsc driver. They aren't functionality
changes so not targeting net-next; and they are not show stopper
bugs that need to go to stable either.

v2
   - drop the irq flags patch, defer it to net-next
   - split the multicast filter flag patch out
   - change propogate rx mode patch to handle startup of vf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The netvsc device should propagate filters to the SR-IOV VF
device (if present). The flags also need to be propagated to the
VF device as well. This only really matters on local Hyper-V
since Azure does not support multiple addresses.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netvsc driver was always enabling all multicast and broadcast
even if netdevice flag had not enabled it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When VF is used for accelerated networking it will likely have
more queues (and different policy) than the synthetic NIC.
This patch defers the queue policy to the VF so that all the
queues can be used. This impacts workloads like local generate UDP.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the netvsc_channel_cb is already called in interrupt
context from vmbus, there is no need to do irqsave/restore.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a race between napi_reschedule and re-enabling interrupts
which could lead to missed host interrrupts.  This occurs when
interrupts are re-enabled (hv_end_read) and vmbus irq callback
(netvsc_channel_cb) has already scheduled NAPI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Block setup of multiple channels earlier in the teardown
process. This avoids possible races between halt and subchannel
initialization.
Suggested-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Need to delete NAPI association if vmbus_open fails.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't wake transmit queues if link is not up yet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the initialization order so that the device is ready to transmit
(ie connect vsp is completed) before setting the internal reference
to the device with RCU.

This avoids any races on initialization and prevents retry issues
on shutdown.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XDP_REDIRECT support for mergeable buffer was removed since commit
7324f539 ("virtio_net: disable XDP_REDIRECT in receive_mergeable()
case"). This is because we don't reserve enough tailroom for struct
skb_shared_info which breaks XDP assumption. So this patch fixes this
by reserving enough tailroom and using fixed size of rx buffer.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PPP units don't hold any reference on the channels connected to it.
It is the channel's responsibility to ensure that it disconnects from
its unit before being destroyed.
In practice, this is ensured by ppp_unregister_channel() disconnecting
the channel from the unit before dropping a reference on the channel.

However, it is possible for an unregistered channel to connect to a PPP
unit: register a channel with ppp_register_net_channel(), attach a
/dev/ppp file to it with ioctl(PPPIOCATTCHAN), unregister the channel
with ppp_unregister_channel() and finally connect the /dev/ppp file to
a PPP unit with ioctl(PPPIOCCONNECT).

Once in this situation, the channel is only held by the /dev/ppp file,
which can be released at anytime and free the channel without letting
the parent PPP unit know. Then the ppp structure ends up with dangling
pointers in its ->channels list.

Prevent this scenario by forbidding unregistered channels from
connecting to PPP units. This maintains the code logic by keeping
ppp_unregister_channel() responsible from disconnecting the channel if
necessary and avoids modification on the reference counting mechanism.

This issue seems to predate git history (successfully reproduced on
Linux 2.6.26 and earlier PPP commits are unrelated).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

iproute2 print_skbmod() prints the configured ethertype using format 0x%X:
therefore, test 9aa8 systematically fails, because it configures action #4
using ethertype 0x0031, and expects 0x0031 when it reads it back. Changing
the expected value to 0x31 lets the test result 'not ok' become 'ok'.

tested with:
 # ./tdc.py -e 9aa8
 Test 9aa8: Get a single skbmod action from a list
 All test results:

 1..1
 ok 1 9aa8 Get a single skbmod action from a list

Fixes: cf797ac4 ("tc-testing: Add test cases for police and skbmod")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now, we assumed that in case of error when adding FDB entries, the
write operation will fail, but this is not the case. Instead, we need to
check that the number of entries reported in the response is equal to
the number of entries specified in the request.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Axtens says:

====================
GSO_BY_FRAGS correctness improvements

As requested [1], I went through and had a look at users of gso_size to
see if there were things that need to be fixed to consider
GSO_BY_FRAGS, and I have tried to improve our helper functions to deal
with this case.

I found a few. This fixes bugs relating to the use of
skb_gso_*_seglen() where GSO_BY_FRAGS is not considered.

Patch 1 renames skb_gso_validate_mtu to skb_gso_validate_network_len.
This is follow-up to my earlier patch 2b16f048 ("net: create
skb_gso_validate_mac_len()"), and just makes everything a bit clearer.

Patches 2 and 3 replace the final users of skb_gso_network_seglen() -
which doesn't consider GSO_BY_FRAGS - with
skb_gso_validate_network_len(), which does. This allows me to make the
skb_gso_*_seglen functions private in patch 4 - now future users won't
accidentally do the wrong comparison.

Two things remain. One is qdisc_pkt_len_init, which is discussed at
[2] - it's caught up in the GSO_DODGY mess. I don't have any expertise
in GSO_DODGY, and it looks like a good clean fix will involve
unpicking the whole validation mess, so I have left it for now.

Secondly, there are 3 eBPF opcodes that change the gso_size of an SKB
and don't consider GSO_BY_FRAGS. This is going through the bpf tree.

Regards,
Daniel

[1] https://patchwork.ozlabs.org/comment/1852414/
[2] https://www.spinics.net/lists/netdev/msg482397.html

PS: This is all in the core networking stack. For a driver to be
affected by this it would need to support NETIF_F_GSO_SCTP /
NETIF_F_GSO_SOFTWARE and then either use gso_size or not be a purely
virtual device. (Many drivers look at gso_size, but do not support
SCTP segmentation, so the core network will segment an SCTP gso before
it hits them.) Based on that, the only driver that may be affected is
sunvnet, but I have no way of testing it, so I haven't looked at it.

v2: split out bpf stuff
    fix review comments from Dave Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

They're very hard to use properly as they do not consider the
GSO_BY_FRAGS case. Code should use skb_gso_validate_network_len
and skb_gso_validate_mac_len as they do consider this case.

Make the seglen functions static, which stops people using them
outside of skbuff.c
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace skb_gso_network_seglen() with
skb_gso_validate_network_len(), as it considers the GSO_BY_FRAGS
case.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tbf_enqueue() checks the size of a packet before enqueuing it.
However, the GSO size check does not consider the GSO_BY_FRAGS
case, and so will drop GSO SCTP packets, causing a massive drop
in throughput.

Use skb_gso_validate_mac_len() instead, as it does consider that
case.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If you take a GSO skb, and split it into packets, will the network
length (L3 headers + L4 headers + payload) of those packets be small
enough to fit within a given MTU?

skb_gso_validate_mtu gives you the answer to that question. However,
we recently added to add a way to validate the MAC length of a split GSO
skb (L2+L3+L4+payload), and the names get confusing, so rename
skb_gso_validate_mtu to skb_gso_validate_network_len
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are some batman-adv bugfixes:

 - fix skb checksum issues, by Matthias Schiffer (2 patches)

 - fix exception handling when dumping data objects through netlink,
   by Sven Eckelmann (4 patches)

 - fix handling of interface indices, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Put back reference on CLUSTERIP configuration structure from the
   error path, patch from Florian Westphal.

2) Put reference on CLUSTERIP configuration instead of freeing it,
   another cpu may still be walking over it, also from Florian.

3) Refetch pointer to IPv6 header from nf_nat_ipv6_manip_pkt() given
   packet manipulation may reallocation the skbuff header, from Florian.

4) Missing match size sanity checks in ebt_among, from Florian.

5) Convert BUG_ON to WARN_ON in ebtables, from Florian.

6) Sanity check userspace offsets from ebtables kernel, from Florian.

7) Missing checksum replace call in flowtable IPv4 DNAT, from Felix
   Fietkau.

8) Bump the right stats on checksum error from bridge netfilter,
   from Taehee Yoo.

9) Unset interface flag in IPv6 fib lookups otherwise we get
   misleading routing lookup results, from Florian.

10) Missing sk_to_full_sk() in ip6_route_me_harder() from Eric Dumazet.

11) Don't allow devices to be part of multiple flowtables at the same
    time, this may break setups.

12) Missing netlink attribute validation in flowtable deletion.

13) Wrong array index in nf_unregister_net_hook() call from error path
    in flowtable addition path.

14) Fix FTP IPVS helper when NAT mangling is in place, patch from
    Julian Anastasov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Three more patches:
 * fix for a regression in 4-addr mode with fast-RX
 * fix for a Kconfig problem with the new regdb
 * fix for the long-standing TCP performance issue in
   wifi using the new sk_pacing_shift_update()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0933a578 ("rds: tcp: use sock_create_lite() to create the
accept socket") has a reference counting issue in TCP socket creation
when accepting a new connection.  The code uses sock_create_lite() to
create a kernel socket.  But it does not do __module_get() on the
socket owner.  When the connection is shutdown and sock_release() is
called to free the socket, the owner's reference count is decremented
and becomes incorrect.  Note that this bug only shows up when the socket
owner is configured as a kernel module.

v2: Update comments

Fixes: 0933a578 ("rds: tcp: use sock_create_lite() to create the accept socket")
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-02-28

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Add schedule points and reduce the number of loop iterations
   the test_bpf kernel module is performing in order to not hog
   the CPU for too long, from Eric.

2) Fix an out of bounds access in tail calls in the ppc64 BPF
   JIT compiler, from Daniel.

3) Fix a crash on arm64 on unaligned BPF xadd operations that
   could be triggered via interpreter and JIT, from Daniel.

Please not that once you merge net into net-next at some point, there
is a minor merge conflict in test_verifier.c since test cases had
been added at the end in both trees. Resolution is trivial: keep all
the test cases from both trees.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If ethtool_ops->get_fecparam returns an error, pass that error on to the
 user, rather than ignoring it.

Fixes: 1a5f3da2 ("net: ethtool: add support for forward error correction modes")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ip_error() is called the device is the l3mdev master instead of the
original device. So the forwarding check should be on the original one.

Changes from v2:
- Handle the original device disappearing (per David Ahern)
- Minimize the change in code order

Changes from v1:
- Only need to reset the device on which __in_dev_get_rcu() is done (per
  David Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting an interface into a VRF fails with 'RTNETLINK answers: File
exists' if one of its VLAN interfaces is already in the same VRF.
As the VRF is an upper device of the VLAN interface, it is also showing
up as an upper device of the interface itself. The solution is to
restrict this check to devices other than master. As only one master
device can be linked to a device, the check in this case is that the
upper device (VRF) being linked to is not the same as the master device
instead of it not being any one of the upper devices.

The following example shows an interface ens12 (with a VLAN interface
ens12.10) being set into VRF green, which behaves as expected:

  # ip link add link ens12 ens12.10 type vlan id 10
  # ip link set dev ens12 master vrfgreen
  # ip link show dev ens12
    3: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
       master vrfgreen state UP mode DEFAULT group default qlen 1000
       link/ether 52:54:00:4c:a0:45 brd ff:ff:ff:ff:ff:ff

But if the VLAN interface has previously been set into the same VRF,
then setting the interface into the VRF fails:

  # ip link set dev ens12 nomaster
  # ip link set dev ens12.10 master vrfgreen
  # ip link show dev ens12.10
    39: ens12.10@ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
    qdisc noqueue master vrfgreen state UP mode DEFAULT group default
    qlen 1000 link/ether 52:54:00:4c:a0:45 brd ff:ff:ff:ff:ff:ff
  # ip link set dev ens12 master vrfgreen
    RTNETLINK answers: File exists

The workaround is to move the VLAN interface back into the default VRF
beforehand, but it has to be shut first so as to avoid the risk of
traffic leaking from the VRF. This fix avoids needing this workaround.
Signed-off-by: Mike Manning <mmanning@att.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The newly introudced ip_min_valid_pmtu variable is only used when
CONFIG_SYSCTL is set:

net/ipv4/route.c:135:12: error: 'ip_min_valid_pmtu' defined but not used [-Werror=unused-variable]

This moves it to the other variables like it, to avoid the harmless
warning.

Fixes: c7272c2f ("net: ipv4: don't allow setting net.ipv4.route.min_pmtu below 68")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IPS_NAT_MASK check in 4.12 replaced previous check for nfct_nat()
which was needed to fix a crash in 2.6.36-rc, see
commit 7bcbf81a ("ipvs: avoid oops for passive FTP").
But as IPVS does not set the IPS_SRC_NAT and IPS_DST_NAT bits,
checking for IPS_NAT_MASK prevents PASV response to be properly
mangled and blocks the transfer. Remove the check as it is not
needed after 3.12 commit 41d73ec0 ("netfilter: nf_conntrack:
make sequence number adjustments usuable without NAT") which
changes nfct_nat() with nfct_seqadj() and especially after 3.13
commit b25adce1 ("ipvs: correct usage/allocation of seqadj
ext in ipvs").

Thanks to Li Shuang and Florian Westphal for reporting the problem!
Reported-by: Li Shuang <shuali@redhat.com>
Fixes: be7be6e1 ("netfilter: ipvs: fix incorrect conflict resolution")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Jiri Pirko says:

====================
mlxsw: couple of fixes

Couple of unrelated fixes for mlxsw.

---
v1->v2:
-patch 2:
 - rebase on top of current -net tree
 - removed forgotten empty line
-patch 3:
 - new patch
-patch 4:
 - new patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the basic construct in the device is a port-VLAN pair, which can
be bound to a FID or a RIF in order to direct packets to the bridge or
the router, respectively.

Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs.
sw1p1.10), VID 1 is used to represent these and thus this VID can be
used by both upper devices of mlxsw ports and by the driver itself.

However, this VID is not reference counted and therefore might be freed
prematurely, which can result in various WARNINGs. For example:

$ ip link add name br0 type bridge vlan_filtering 1
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev team0 master br0
$ ip link set dev enp1s0np1 master team0
$ ip address add 192.0.2.1/24 dev enp1s0np1

The enslavement to team0 will fail because team0 already has an upper
and thus vlan_vids_del_by_dev() will be executed as part of team's error
path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The
WARNING will be generated when the driver will realize it can't find VID
1 on the port and bind it to a RIF.

Fix this by adding a reference count to the VLAN entries on the port, in
a similar fashion to the reference counting used by the corresponding
'vlan_vid_info' structure in the 8021q driver.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Reported-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When multicast snooping is enabled, the Linux bridge resorts to flooding
unregistered multicast packets to all ports only in case it did not
detect a querier in the network.

The above condition is not reflected to underlying drivers, which is
especially problematic in IPv6 environments, as multicast snooping is
enabled by default and since neighbour solicitation packets might be
treated as unregistered multicast packets in case there is no
corresponding MDB entry.

Until the Linux bridge reflects its querier state to underlying drivers,
simply treat unregistered multicast packets as broadcast and allow them
to reach their destination.

Fixes: 9df552ef ("mlxsw: spectrum: Improve IPv6 unregistered multicast flooding")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current code uses global variables, adjusts them and passes pointer down
to devlink. With every other mlxsw_core instance, the previously passed
pointer values are rewritten. Fix this by de-globalize the variables and
also memcpy size_params during devlink resource registration.
Also, introduce a convenient size_param_init helper.

Fixes: ef3116e5 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IP_TTL, IP_ECN and IP_DSCP are using the same offset within the
scratchpad as L4 ports. Fix this by shifting all up.

Fixes: 5f57e090 ("mlxsw: acl: Add ip ttl acl element")
Fixes: i80d0fe47 ("mlxsw: acl: Add ip tos acl element")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: fixes 2018-02-28

here are 3 smc bug fixes for the net-tree. Karsten's first patch is
the reworked version of last week's
   "[PATCH net-next 2/5] net/smc: fix structure size"
patch, now solved without using __packed, and now targetted for net
instead of net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

when sock_create_kern(..., a) returns an error, 'a' might not be a valid
pointer, so it shouldn't be dereferenced to read a->sk->sk_sndbuf and
and a->sk->sk_rcvbuf; not doing that caused the following crash:

general protection fault: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
    (ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 4254 Comm: syzkaller919713 Not tainted 4.16.0-rc1+ #18
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:smc_create+0x14e/0x300 net/smc/af_smc.c:1410
RSP: 0018:ffff8801b06afbc8 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8801b63457c0 RCX: ffffffff85a3e746
RDX: 0000000000000004 RSI: 00000000ffffffff RDI: 0000000000000020
RBP: ffff8801b06afbf0 R08: 00000000000007c0 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff8801b6345c08 R14: 00000000ffffffe9 R15: ffffffff8695ced0
FS:  0000000001afb880(0000) GS:ffff8801db200000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000040 CR3: 00000001b0721004 CR4: 00000000001606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
  __sock_create+0x4d4/0x850 net/socket.c:1285
  sock_create net/socket.c:1325 [inline]
  SYSC_socketpair net/socket.c:1409 [inline]
  SyS_socketpair+0x1c0/0x6f0 net/socket.c:1366
  do_syscall_64+0x282/0x940 arch/x86/entry/common.c:287
  entry_SYSCALL_64_after_hwframe+0x26/0x9b
RIP: 0033:0x4404b9
RSP: 002b:00007fff44ab6908 EFLAGS: 00000246 ORIG_RAX: 0000000000000035
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00000000004404b9
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 000000000000002b
RBP: 00007fff44ab6910 R08: 0000000000000002 R09: 00007fff44003031
R10: 0000000020000040 R11: 0000000000000246 R12: ffffffffffffffff
R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000
Code: 48 c1 ea 03 80 3c 02 00 0f 85 b3 01 00 00 4c 8b a3 48 04 00 00 48
b8
00 00 00 00 00 fc ff df 49 8d 7c 24 20 48 89 fa 48 c1 ea 03 <80> 3c 02
00
0f 85 82 01 00 00 4d 8b 7c 24 20 48 b8 00 00 00 00
RIP: smc_create+0x14e/0x300 net/smc/af_smc.c:1410 RSP: ffff8801b06afbc8

Fixes: cd6851f3 smc: remote memory buffers (RMBs)
Reported-and-tested-by: syzbot+aa0227369be2dcc26ebe@syzkaller.appspotmail.com
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>