Do the check before we re-enable interrupts and clean the code
up a bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This has a page of comment explaining what's going on right in
the middle of do_page_fault() which makes things a bit hard to
follow. Move it to a helper instead. Also do the test earlier
as there's no point waiting until after we found the VMA.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

No need to break those lines, they aren't that long
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

It makes do_page_fault() more readable. No functional change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

First, handle the normal retry failure in do_page_fault itself,
since it's a simple return statement. That allows us to remove
the "continue" special return code from mm_fault_error().

Once that's done, we can have an implementation much closer to
x86 where we only call mm_fault_error() if VM_FAULT_ERROR is set
and directly return.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Instead of goto labels, instead call those functions and return.

This gets us closer to x86 and allows us to shring do_page_fault()
even more.

The main difference with x86 is that those function return a value
which we then return from do_page_fault(). That value is our
return value from do_page_fault() which we use to generate
kernel faults.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We currently test for is_exec and DSISR_PROTFAULT but that doesn't
make sense as this is the wrong error bit to test for an execute
permission failure.

In fact, we had code that would return early if we had an exec
fault in kernel mode so I think that was just dead code anyway.

Finally the location of that test is awkward and prevents further
simplifications.

So instead move that test into a helper along with the existing
early test for kernel exec faults and out of range accesses,
and put it all in a "bad_kernel_fault()" helper. While at it
test the correct error bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Now that we moved the exception state handling to a wrapper, we can
just directly return rather than "goto bail"
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

unclutters the main path
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

A bad page fault is when the HW signals an error such as a bad
copy/paste, an AMO error, or some other type of error that will
not be fixed by updating the PTE.

Use a helper page_fault_is_bad() to check for bad page faults thus
removing the per-processor family open-coding in __do_page_fault()
and trigger a SIGBUS rather than a SIGSEGV which is more appropriate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

There's no point looking for the VMA etc.. when we already know
we are going to fail.

This adds some code to set "code" for the si_code but that will
be gone in subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Define a common page_fault_is_write() helper and use it
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This uses the newly defined constants for this rather than open-coded
numbers. There is a side effect on 64-bit which is to pass through
some of the new P9 bits which we didn't before.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We test a number of bits from DSISR/SRR1 before deciding
to call hash_page(). If any of these is set, we go directly
to do_page_fault() as the bit indicate a fault that needs
to be handled there (no hashing needed).

This updates the current open-coded masks to use the new
DSISR definitions.

This *does* change the masks actually used in two ways:

 - We used to test various bits that were defined as "always 0"
in the architecture and could be repurposed for something
else. From now on, we just ignore such bits.

 - We were missing some new bits defined on P9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This updates the definitions for the various DSISR bits to
match both some historical stuff and to match new bits on
POWER9.

In addition, we define some masks corresponding to the "bad"
faults on Book3S, and some masks corresponding to the bits
that match between DSISR and SRR1 for a DSI and an ISI.

This comes with a small code update to change the definition
of DSISR_PGDIRFAULT which becomes DSISR_PRTABLE_FAULT to
match architecture 3.0B
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On legacy 6xx 32-bit procesors, we checked for the DABR match bit
in DSISR from do_page_fault(), in the middle of a pile of ifdef's
because all other CPU types do it in assembly prior to calling
do_page_fault. Fix that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Add #ifdef CONFIG_6xx]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

By filtering the relevant SRR1 bits in the assembly rather than
in do_page_fault() itself, we avoid a conditional branch (since we
already come from different path for data and instruction faults).

This will allow more simplifications later
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This will allow simplifying the returns from do_page_fault
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We do that because it's used by THP pmd collapsing, so use
instead a dedicated flush function.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

At the moment we have to rather sub-optimal flushing behaviours:

 - flush_tlb_mm() will flush the PWC which is unnecessary (for example
   when doing a fork)

 - A large unmap will call flush_tlb_pwc() multiple times causing us
   to perform that fairly expensive operation repeatedly. This happens
   often in batches of 3 on every new process.

So we change flush_tlb_mm() to only flush the TLB, and we use the
existing "need_flush_all" flag in struct mmu_gather to indicate
that the PWC needs flushing.

Unfortunately, flush_tlb_range() still needs to do a full flush
for now as it's used by the THP collapsing. We will fix that later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The PWC flush only needs a single set call, just like the
full (RIC=2) flush.

This will allow us to get rid of the dedicated _tlbiel_pwc()
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Replace the __this_cpu_read() with raw_cpu_read() in
iommu_range_alloc(). Otherwise we get a warning about using
__this_cpu_read() in preemptible code:

  BUG: using __this_cpu_read() in preemptible
  caller is iommu_range_alloc+0xa8/0x3d0

Preemption doesn't need to be disabled since according to the comment
any CPU can safely use any IOMMU pool.
Signed-off-by: Victor Aoqui <victora@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently we use the stop-api provided by the firmware to program the
SLW engine to restore the values of hypervisor resources that get lost
on deeper idle states (such as winkle). Since the deep states were
only used for CPU-Hotplug on POWER8 systems, we would program the LPCR
to have the PECE1 bit since Hotplugged CPUs shouldn't be spuriously
woken up by decrementer.

On POWER9, some of the deep platform idle states such as stop4 can be
used in cpuidle as well. In this case, we want the CPU in stop4 to be
woken up by the decrementer when some timer on the CPU expires.

In this patch, we program the stop-api for LPCR with PECE1
bit cleared only when we are offlining the CPU and set it
back once the CPU is online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The stop4 idle state on POWER9 is a deep idle state which loses
hypervisor resources, but whose latency is low enough that it can be
exposed via cpuidle.

Until now, the deep idle states which lose hypervisor resources (eg:
winkle) were only exposed via CPU-Hotplug.  Hence currently on wakeup
from such states, barring a few SPRs which need to be restored to
their older value, rest of the SPRS are reinitialized to their values
corresponding to that at boot time.

When stop4 is used in the context of cpuidle, we want these additional
SPRs to be restored to their older value, to ensure that the context
on the CPU coming back from idle is same as it was before going idle.

In this patch, we define a SPR save area in PACA (since we have used
up the volatile register space in the stack) and on POWER9, we restore
SPRN_PID, SPRN_LDBAR, SPRN_FSCR, SPRN_HFSCR, SPRN_MMCRA, SPRN_MMCR1,
SPRN_MMCR2 to the values they had before entering stop.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The offset of hugepage block will not be 16G, if the expected
page is more than one. Calculate the totol size instead of the
hardcode value.

Fixes: 4792adba ("powerpc: Don't use a 16G page if beyond mem= limits")
Signed-off-by: Rui Teng <rui.teng@linux.vnet.ibm.com>
Tested-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

For debugging very early boot problems we have CONFIG_PPC_EARLY_DEBUG,
which allows configuring the kernel such that it unconditionally writes
to a particular type of console, regardless of whether that console
exists or not. This is useful sometimes when the kernel crashes before
it can even determine what platform it's on, and therefore what consoles
exist.

However if you boot a kernel built this way on a different platform, it
will generally crash because it writes to a console that doesn't exist.

A particularly nasty instance of this is if you enable the hypervisor
console early debug, and then boot that kernel on bare metal. The result
is that the kernel calls "the hypervisor" very early in boot, but the
kernel *is* the hypervisor, so we jump to the system call handler and
start executing all sorts of code that isn't ready to be run. This may
lead to a machine check or check stop depending on how lucky you are.

Luckily there is an easy way to avoid this particular case. We simply
read the MSR before installing the hooks, and if we see MSR_HV is set
then we are the hypervisor and we definitely should not use the
hypervisor console.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Although pretty much everyone using powernv is running little endian,
we should still test we can build for big endian. So add a
powernv_be_defconfig, which is autogenerated by flipping the endian
symbol in powernv_defconfig.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>

Add support to register Thread In-Memory Collection PMU counters.
Patch adds thread IMC specific data structures, along with memory
init functions and CPU hotplug support.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Hemant Kumar <hemant@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add support to register Core In-Memory Collection PMU counters.
Patch adds core IMC specific data structures, along with memory
init functions and CPU hotplug support.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Hemant Kumar <hemant@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add support to register Nest In-Memory Collection PMU counters.
Patch adds a new device file called "imc-pmu.c" under powerpc/perf
folder to contain all the device PMU functions.

Device tree parser code added to parse the PMU events information
and create sysfs event attributes for the PMU.

Cpumask attribute added along with Cpu hotplug online/offline functions
specific for nest PMU. A new state "CPUHP_AP_PERF_POWERPC_NEST_IMC_ONLINE"
added for the cpu hotplug callbacks. Error handle path frees the memory
and unregisters the CPU hotplug callbacks.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Hemant Kumar <hemant@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Code to create platform device for the In-Memory Collection (IMC)
counters. Platform devices are created based on the IMC compatibility.
New header file created to contain the data structures and macros
needed for In-Memory Collection (IMC) counter pmu devices.

The device tree for IMC counters starts at the node "imc-counters".
This node contains all the IMC PMU nodes and event nodes for these IMC
PMUs. Device probe() parses the device to locate three possible IMC
device types (Nest/Core/Thread). Function then branch to parse each
unit nodes to populate vital information such as device memory sizes,
event nodes information, base address for reserve memory access (if
any) and so on. Simple bare-minimum shutdown function added which only
"stops" the engines.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Hemant Kumar <hemant@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Fix build with CONFIG_PERF_EVENTS=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In-Memory Collection (IMC) counters are performance monitoring
infrastructure. These counters need special sequence of SCOMs to
init/start/stop which is handled by OPAL. And OPAL provides three APIs
to init and control these IMC engines.

OPAL API documentation:
  https://github.com/open-power/skiboot/blob/master/doc/opal-api/opal-imc-counters.rst

Patch updates the kernel side powernv platform code to support the new
OPAL APIs
Signed-off-by: Hemant Kumar <hemant@linux.vnet.ibm.com>
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We can use pfn_to_page() in realmode for other configs. Hence remove the
CONFIG_FLATMEM ifdef.

Fixes: 8e0861fa ("powerpc: Prepare to support kernel handling of IOMMU map/unmap")
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Also fix up the #endif comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

All cases initialise rv, and if they didn't that would be a bug. By
dropping the initialisation we give the compiler the chance to catch
those bugs for us.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Use memdup_user_nul() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

External IRQ0 (index 48) has the same capabilities as the other IRQ1-7
and is handled by the same register IPIC_SEPNR. When this register is
not specified for "ack" in "ipic_info", you cannot configure this IRQ
as IRQ_TYPE_EDGE_FALLING. This oversight was probably due to the
non-contiguous hwirq numbering of IRQ0 in the IPIC.
Signed-off-by: Jurgen Schindele <schindele@nentec.de>
[scottwood: Cleaned up commit message and posted as a proper patch]
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This allows building powerpc with the GENERIC_MSI_IRQ_DOMAIN
Kconfig by enabling the asm-generic msi.h in Kbuild. Without
this, there's a compilation error [1] because powerpc, as most
arches, doesn't provide an asm/msi.h.

[1] In file included from ./include/linux/kvm_host.h:20:0,
                 from ./arch/powerpc/include/asm/kvm_ppc.h:30,
                 from arch/powerpc/kernel/dbell.c:20:
./include/linux/msi.h:195:21: fatal error: asm/msi.h: No such file or directory
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Check for validity of cpu before calling get_hard_smp_processor_id().

Found with coverity.
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>