We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.

Note that we also fix a harmless typo for the node name, it's
dispc@400, not dispc@4000.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On am437x, the display subsystem (DSS) is on l4. We already have
the interconnect target module for it, so let's just move dss
there.

To do that, we need to adjust the module addresses for the ranges,
and use the ranges already added earlier based on reading the l4
interconnect instance AP registers.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.

Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.

Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Note that we must disable smart idle modes for HDMI audio like we've
done with the legacy platform data. And HDMI needs both hdmi clock
and dss clock to operate.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.

We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.

We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.

The display subsystem (DSS) is in a 16MB interconnect target module
mapped to l4 and l3 buses. We are only using the l3 port as recommended
by the TRM. So there is no need to configure l4 ranges like we've done
for l4 ABE instance for example.

Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.

Let's also add add a note about using only the l3 access without l4
as noted in the TRM.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The PRU-ICSS present on AM33xx/AM43xx/AM57xx has a very unique
SYSCFG register. The register follows the OMAP4-style SYSC_TYPE3
for Master Standby and Slave Idle, but also has two additional
unique fields - STANDBY_INIT and SUB_MWAIT. The STANDBY_INIT is
a control bit that is used to initiate a Standby sequence (when
set) and trigger a MStandby request to the SoC's PRCM module. This
same bit is also used to enable the OCP master ports (when cleared)
to allow the PRU cores to access any peripherals or memory beyond
the PRU subsystem. The SUB_MWAIT is a ready status field for the
external access.

Add support for this SYSC type. The STANDBY_INIT has to be set
during suspend, without which it results in a hang in the resume
sequence on AM33xx/AM43xx boards and requires a board reset to
come out of the hang. Any PRU applications requiring external
access are supposed to clear the STANDBY_INIT bit. Note that
the PRUSS context is lost during a suspend sequence because the
PRUSS module is reset and/or disabled.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated quirk define number and to use -ENODEV]
Signed-off-by: Tony Lindgren <tony@atomide.com>

The PRUSS module has a SYSCFG which is unique. The SYSCFG
has two additional unique fields called STANDBY_INIT and
SUB_MWAIT in addition to regular IDLE_MODE and STANDBY_MODE
fields. Add the bindings for this new sysc type.

Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In order to probe EDMA with ti-sysc interconnect target module and with
device tree data, we need to properly detect EDMA and set the flags for
SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY for tptc.

We have these flags currently set for am4 and dra7, but not for am335x.
Let's set them for all the SoCs as the tptc module should behave the
same for all of them. It's likely that am335x was never tested to idle
EDMA tptc.

Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 7324a7a0 ("bus: ti-sysc: Implement display subsystem reset
quirk") added support for DSS reset, but is using dispc offset also for
DSS also registers as reported by Tomi Valkeinen <tomi.valkeinen@ti.com>.
Also, we're not using dispc_offset for dispc IRQSTATUS register so let's
fix that too.

Fixes: 7324a7a0 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The display subsystem (DSS) needs the child outputs disabled for reset.
In order to prepare to probe DSS without legacy platform data, let's
implement sysc_pre_reset_quirk_dss() similar to what we have for the
platform data with omap_dss_reset().

Note that we cannot directly use the old omap_dss_reset() without
platform data callbacks and updating omap_dss_reset() to understand
struct device. And we will be dropping omap_dss_reset() anyways when
all the SoCs are probing with device tree, so let's not mess with the
legacy code at all.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In order to prepare probing display subsystem (DSS) with ti-sysc
interconnect target module driver and device tree data, let's
detect DSS related modules.

We need to also add reset quirk handling for DSS, but until that's
done, let's just enable the optional clock quirks for DSS and
omap4 HDMI. The rest is just naming of modules if CONFIG_DEBUG
is set.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The RTC modules on am3 and am4 need quirk handling to unlock and lock
them for reset so let's add the quirk handling based on what we already
have for legacy platform data. In later patches we will simply drop the
RTC related platform data and the old quirk handling.
Signed-off-by: Tony Lindgren <tony@atomide.com>

We need to know SoC type and features for cases where the same SoC
may be installed in various versions on the same board and would need
a separate dts file otherwise for the different variants.

For example, am3703 is pin compatible with omap3630, but has sgx and
iva accelerators disabled. We must not try to access the sgx or iva
module registers on am3703, and need to set the unavailable devices
disabled early.

Let's also detect omap3430 as that is needed for display subsystem
(DSS) reset later on, and GP vs EMU or HS devices. Further SoC
specific disabled device detection can be added as needed, such as
dra71x vs dra76x rtc and usb4.

Cc: Adam Ford <aford173@gmail.com>
Cc: André Hentschel <nerv@dawncrow.de>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In some cases we can have nested ti-sysc instances that may still use the
legacy "ti,hwmods" property. Let's not warn if that's the case.
Signed-off-by: Tony Lindgren <tony@atomide.com>

We are currently setting -1 for non-existing sysconfig related registers
for quirks, but setting -ENODEV elsewhere. And for matching the quirks,
we're now just ignoring the non-existing registers. This will cause issues
with misdetecting DSS registers as the hardware revision numbers can have
duplicates.

To avoid this, let's standardize on using -ENODEV also for the quirks
instead of -1. That way we can always just test for a match without adding
any more complicated logic.
Signed-off-by: Tony Lindgren <tony@atomide.com>

At least display susbsystem (DSS) has modules with no sysconfig registers
and rely on custom function for module reset handling. Let's make reset
work with that too.
Signed-off-by: Tony Lindgren <tony@atomide.com>

The clk_disable_quirk and clk_enable_quirk should really be called
pre_reset_quirk and post_reset_quirk to avoid confusion like we had
with hdq1w reset.

Let's also rename the related functions so the code is easier to follow.
Note that we also have reset_done_quirk that is needed in some cases
after checking the separate register for reset done bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Because of the i2c quirk we have the reset quirks named in a confusing
way. Let's fix the 1-wire quirk accordinlyg. Then let's switch to using
better naming later on.

Fixes: 4e23be47 ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>

In order to probe display subsystem (DSS) components with ti-sysc
interconnect target module without legacy platform data and using
devicetree, we need to update dss probing a bit.

In the device tree, we will be defining the data also for the interconnect
target modules as DSS really is a private interconnect. There is some
information about that in 4460 TRM in "Figure 10-3. DSS Integration" for
example where it mentions "32-bit interconnect (SLX)".

The changes we need to make are:

1. Parse also device tree subnodes for the compatible property fixup

2. Update the component code to consider device tree subnodes

Cc: dri-devel@lists.freedesktop.org
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull more Kbuild updates from Masahiro Yamada:

 - fix randconfig to generate a sane .config

 - rename hostprogs-y / always to hostprogs / always-y, which are more
   natual syntax.

 - optimize scripts/kallsyms

 - fix yes2modconfig and mod2yesconfig

 - make multiple directory targets ('make foo/ bar/') work

* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: make multiple directory targets work
  kconfig: Invalidate all symbols after changing to y or m.
  kallsyms: fix type of kallsyms_token_table[]
  scripts/kallsyms: change table to store (strcut sym_entry *)
  scripts/kallsyms: rename local variables in read_symbol()
  kbuild: rename hostprogs-y/always to hostprogs/always-y
  kbuild: fix the document to use extra-y for vmlinux.lds
  kconfig: fix broken dependency in randconfig-generated .config

Pull new zonefs file system from Damien Le Moal:
 "Zonefs is a very simple file system exposing each zone of a zoned
  block device as a file.

  Unlike a regular file system with native zoned block device support
  (e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
  sequential write constraint of zoned block devices to the user. As a
  result, zonefs is not a POSIX compliant file system. Its goal is to
  simplify the implementation of zoned block devices support in
  applications by replacing raw block device file accesses with a richer
  file based API, avoiding relying on direct block device file ioctls
  which may be more obscure to developers.

  One example of this approach is the implementation of LSM
  (log-structured merge) tree structures (such as used in RocksDB and
  LevelDB) on zoned block devices by allowing SSTables to be stored in a
  zone file similarly to a regular file system rather than as a range of
  sectors of a zoned device. The introduction of the higher level
  construct "one file is one zone" can help reducing the amount of
  changes needed in the application while at the same time allowing the
  use of zoned block devices with various programming languages other
  than C.

  Zonefs IO management implementation uses the new iomap generic code.
  Zonefs has been successfully tested using a functional test suite
  (available with zonefs userland format tool on github) and a prototype
  implementation of LevelDB on top of zonefs"

* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Add documentation
  fs: New zonefs file system

In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.

Fixes: 4e6437f1 ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:

   - Important fix for multichannel and for modefromsid mounts.

   - Two reconnect fixes

   - Addition of SMB3 change notify support

   - Backup tools fix

   - A few additional minor debug improvements (tracepoints and
     additional logging found useful during testing this week)"

* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add defines for new information level, FileIdInformation
  smb3: print warning once if posix context returned on open
  smb3: add one more dynamic tracepoint missing from strict fsync path
  cifs: fix mode bits from dir listing when mounted with modefromsid
  cifs: fix channel signing
  cifs: add SMB3 change notification support
  cifs: make multichannel warning more visible
  cifs: fix soft mounts hanging in the reconnect code
  cifs: Add tracepoints for errors on flush or fsync
  cifs: log warning message (once) if out of disk space
  cifs: fail i/o on soft mounts if sessionsetup errors out
  smb3: fix problem with null cifs super block with previous patch
  SMB3: Backup intent flag missing from some more ops

Pull vboxfs from Al Viro:
 "This is the VirtualBox guest shared folder support by Hans de Goede,
  with fixups for fs_parse folded in to avoid bisection hazards from
  those API changes..."

* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Add VirtualBox guest shared folder (vboxsf) support