Define the Henninger board dependent part of the SDHI0/2 device nodes along with
the necessary voltage regulators (note that the Vcc regulators are dummy -- they
are required but don't actually exist on the board). Also, GPIOs have to be used
for the CD and WP signals due to the SDHI driver constraints...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When creating the initial device tree for the Henninger board,  I've overlooked
that EXTAL frequency needs to be overridden there. The 'sh-sci' driver  managed
to work somehow but the SDHI driver that I've tried to enable just hanged with
the default EXTAL frequency of 0...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable SATA0 device for the Henninger board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Henninger board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device tree for the R8A7791 SoC based Henninger board. SCIF0
serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use "sii,s35390a" instead of "seiko,s35390a", cfr.
Documentation/devicetree/bindings/i2c/trivial-devices.txt and
Documentation/devicetree/bindings/vendor-prefixes.txt.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
[horms+renesas@verge.net.au resolved conflicts]
[horms+renesas@verge.net.au consistently use space as separator]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

All I2C clocks derive from the HP clock, not from the P clock. Fix them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

All I2C clocks derive from the HP clock, not from the P clock. Fix them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The correct binding is "micrel,led-mode", not "led-mode".

This corrects an error which was introduced when setting of ethernet PHY
LED mode was added by 82e62182d59bd1d0 ("ARM: shmobile: lager: Set ethernet
PHY LED mode").

This makes the lager code consistent with the koelsch code which was added
by ae00d12a032490b3 ("ARM: shmobile: koelsch: Set ethernet PHY LED mode").
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This enables the Seiko real-time clock that is attached to a couple of
GPIO pins.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add support for EHCI clock gating via the MSTP703 bit on r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "renesas,*-r8a7740" to the compatible strings for consistency with other
devices.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This node should have a unique name so it can be distinguished when
other i2c busses are added later.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Koelsch board uses the ethernet PHY LED0 as a link signal connected
to the ethernet controller. Specify the corresponding LED mode for the
PHY.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Lager board uses the ethernet PHY LED0 as a link signal connected to
the ethernet controller. Specify the corresponding LED mode for the PHY.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Koelsch board.
This makes the DT code match the legacy board code. Also
update the existing gpio-keys nodes to make use of KEY_n.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Lager board.
This makes the DT code match the legacy board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add Spansion s25fl008k SPI FLASH and MTD partition, based on bockw legacy
board code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

  - Add "renesas,hspi-r8a7779" compatible value,
  - Correct reference to parent interrupt controller
    (use "interrupt-parent" instead of "interrupt-controller"),
  - Add missing "#address-cells" and "#size-cells" properties, which are
    needed when populating the SPI buses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

  - Add "renesas,hspi-r8a7778" compatible value,
  - Correct reference to parent interrupt controller
    (use "interrupt-parent" instead of "interrupt-controller"),
  - Add missing "#address-cells" and "#size-cells" properties, which are
    needed when populating the SPI buses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Koelsch.
On this board, only MSIOF0 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Lager.
On this board, only MSIOF1 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi4.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The correct maximum CPU frequency for r8a7791 is 1500 MHz
so update the r8a7791 SoC DTS to reflect this.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Some versions of gcc even warn about it:

  mm/shmem.c: In function ‘shmem_file_aio_read’:
  mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function

If the loop is aborted during the first iteration by one of the two
first break statements, error will be uninitialized.

Introduced by commit 6e58e79d ("introduce copy_page_to_iter, kill
loop over iovec in generic_file_aio_read()").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>