Document Renesas' RZ/G2E (R8A774C0) GPIO blocks compatibility within the
relevant dt-bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit 21abf103
("gpio: Pass a flag to gpiochip_request_own_desc()")
started to pass an enum gpiod_flags but this file is
not including the header file that defines that enum
and the compiler spits:

drivers/memory/omap-gpmc.c: In function
			    'gpmc_probe_generic_child':
drivers/memory/omap-gpmc.c:2174:9: error: type of formal
				   parameter 4 is incomplete
         0);
         ^

Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 21abf103 ("gpio: Pass a flag to gpiochip_request_own_desc()")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This fixes up a new user of gpiochip_request_own_desc() in
the AMS Delta board that appeared after the patch that was
applied recently.

Fixes: 21abf103 ("gpio: Pass a flag to gpiochip_request_own_desc()")
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Select REGMAP_I2C in Kconfig, since the driver now depends on regmap
and this was missing, thus breaking build on various systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We're getting a reference RPi's firmware node in order to be able to
communicate with it's driver. We should decrease the reference count on
the dt node after being done with it.

Fixes: a98d90e7 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If CONFIG_GPOILIB is not set, the stub of gpio_to_desc() should return
the same type of error as regular version: NULL.  All the callers
compare the return value of gpio_to_desc() against NULL, so returned
ERR_PTR would be treated as non-error case leading to dereferencing of
error value.

Fixes: 79a9becd ("gpiolib: export descriptor-based GPIO interface")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It is possible that the PCA953x is powered down during suspend.
Use regmap cache to assure the registers in the PCA953x are in
line with the driver state after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Drop pca953x_write_single() which is used in one place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace the ad-hoc reg_output output register caching with generic
regcache cache. Drop pca953x_write_single() which is no longer used.
This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace the ad-hoc reg_direction direction register caching with generic
regcache cache. This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Convert the driver to use regmap to access the chips. Due to the convoluted
register mapping scheme, implement read/write/volatile check functions that
untangle the mess and perform check accordingly. This patch does not zap the
internal register cache of the PCA953x driver, nor does it push the regmap
access down into the gpiochip accessors to simplify the review. All that is
in subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of having the I2C register calculation function spread across
multiple accessor functions, pull it out into a single function which
returns the adjusted register address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ad-hoc i2c block write can be replaced by standard register accessor
function, which correctly handles all the chip details and differences.
Do so to simplify the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The PCA957x and PCA953x init functions are almost the same, except for
the different register mapping and one extra write to BKEN register in
case of PCA957x. Factor out the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

At this point, the pca953x_{read,write}_regs_mul() can read single bank
PCA953x GPIO chips as well. Merge the _8 and _mul functions together to
simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

At this point, these two functions only differ in whether they do or do not
set the address increment bit. The 16 GPIO case does not need to set the AI
bit, except for PCA9575 on write, while the 24 GPIO and more case does set
the AI bit always. Merge these two functions together to simplify the code
a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

At this point, these two functions only differ in whether they do or do not
set the address increment bit on PCA9575. Merge these two functions together
to simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The multi-byte IO on various pca953x chips requires the auto-increment bit,
while other chips toggle the LSbit automatically. Note that LSbit toggling
only alternates between two registers during the IO, it is not the same as
address auto-increment. The driver currently assumes that #gpios > 16 implies
auto-increment, while #gpios <= 16 implies LSbit toggling. This is incorrect
at there are chips with 16 GPIOs which require the auto-increment bit.

The PCA9575, according to NXP datasheet rev. 4.2 from 16 April 2015, section
7.3 Command Register, the bit 7 in command register is the auto-increment
bit, which allows programming multiple registers sequentially.

Set this bit both in pca953x_gpio_set_multiple(), where it fixes the multi
register programming, and in pca957x_write_regs_16(), where is simplifies
the function. In fact, the pca957x_write_regs_16() now looks rather similar
to pca953x_write_regs_24() and pca953x_write_regs_16(), which is intended
for subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The PCAL_PINCTRL_MASK is too large. The extended register block on
PCAL6524, which is the largest chip with this block, has the block
limited to address range 0x40..0x7f. This is because the bit 7 in
the command register is used for the Address Increment functionality.

Trim the mask to 0x60 to match the datasheet and to prevent accidental
overwrite of the AI bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The bank_shift = fls(...) code was duplicated in the driver 5 times,
pull it into separate function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The IRQ core code refers to the interrupt type by that name, whereas the
term flow is almost never used. Some GPIO controllers use the term
flow_type, but it is most consistent to just go with the IRQ core
terminology.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'intel-gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel

intel-gpio for v4.21-1

Use managed resource allocation in pch and sodaville drivers.
Switch to use for_each_set_bit() in IRQ handlers.
Headers clean up.
Sort headers in inclusion block alphabetically for better maintenance.
Convert to SPDX identifier and fixing MODULE_LICENSE() when appropriate.
Additional format fixes to rectify debug and message printing.

There is a commit which had been applied to v4.20-rc4, that's why dup.

- c3bc3ff9 MAINTAINERS: Do maintain Intel GPIO drivers via separate tree

The following is an automated git shortlog grouped by driver:

ich:
 -  Convert to use SPDX identifier
 -  Sort headers alphabetically
 -  Join string literals back
 -  Convert pr_<level> to dev_<level>
 -  Switch to use struct device instead of platform_device
 -  Simplify error handling in ichx_write_bit()

intel-mid:
 -  Convert to use SPDX identifier
 -  Remove linux/module.h and sort headers

lynxpoint:
 -  Convert to use SPDX identifier
 -  Remove linux/init.h and sort headers
 -  Use for_each_set_bit() in IRQ handler

MAINTAINERS:
 -  Do maintain Intel GPIO drivers via separate tree

merrifield:
 -  Convert to use SPDX identifier
 -  Remove linux/init.h

pch:
 -  Convert to use SPDX identifier
 -  Sort headers alphabetically
 -  Remove duplicate assignments
 -  Remove redundant __func__ from debug print
 -  Use for_each_set_bit() in IRQ handler
 -  Convert to dev_pm_ops
 -  Convert to use managed functions pcim_* and devm_*

sch:
 -  Convert to use SPDX identifier
 -  Remove linux/init.h and sort headers

sodaville:
 -  Convert to use SPDX identifier
 -  Sort headers alphabetically
 -  Use for_each_set_bit() in IRQ handler
 -  Convert to use managed functions pcim_* and devm_*

Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.

Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The problem is reported for allmodconfig build setup:

  ERROR: "irq_chip_retrigger_hierarchy" [drivers/gpio/gpio-lpc18xx.ko] undefined!
  make[2]: *** [scripts/Makefile.modpost:92: __modpost] Error 1
  make[1]: *** [Makefile:1271: modules] Error 2

My testing in runtime shows that it is sufficient to remove .irq_retrigger
callback, which is assigned to unexported irq_chip_retrigger_hierarchy()
function, I did't observe any regressions, and thus apparently it is a
better fix rather than exporting the function defined in kernel/irq/chip.c
(see commit 52b2a05f ("genirq: Export IRQ functions for module use"))
or sticking the GPIO controller driver build to built-in option only.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 5ddabfe8 ("gpio: lpc18xx: add GPIO pin interrupt controller support")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to include linux/init.h when at the same time
we include linux/module.h.

Remove redundant inclusion.

While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to include linux/init.h when at the same time
we include linux/module.h.

Remove redundant inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to include linux/init.h when at the same time
we include linux/module.h.

Remove redundant inclusion.

While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to include linux/module.h when at the same time
we include linux/init.h.

Remove redundant inclusion.

While here, remove no-op macro and sort header block alphabetically
for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to assign the same values which core does for us anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>