Jakub Kicinski says:

====================
net: sched: propagate extack to cls offloads on destroy and only with skip_sw

This series some of Jiri's comments and the fact that today drivers
may produce extack even if there is no skip_sw flag (meaning the
driver failure is not really a problem), and warning messages will
only confuse the users.

First patch propagates extack to destroy as requested by Jiri, extack
is then propagated to the driver callback for each classifier.  I chose
not to provide the extack on error paths.  As a rule of thumb it seems
best to keep the extack of the condition which caused the error.  E.g.

     err = this_will_fail(arg, extack);
     if (err) {
        undo_things(arg, NULL /* don't pass extack */);
	return err;
     }

Note that NL_SET_ERR_MSG() will ignore the message if extack is NULL.
I was pondering whether we should make NL_SET_ERR_MSG() refuse to
overwrite the msg, but there seem to be cases in the tree where extack
is set like this:

     err = this_will_fail(arg, extack);
     if (err) {
        undo_things(arg, NULL /* don't pass extack */);
	NL_SET_ERR_MSG(extack, "extack is set after undo call :/");
	return err;
     }

I think not passing extack to undo calls is reasonable.

v2:
 - rename the temporary tc_cls_common_offload_init().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

All users are now converted to tc_cls_common_offload_init().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate extack on removal of offloaded filter.  Don't pass
extack from error paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass offload flags to the new implementation of
tc_cls_common_offload_init().  Extack will now only
be set if user requested skip_sw.  hnodes need to
hold onto the flags now to be able to reuse them
on filter removal.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate extack on removal of offloaded filter.  Don't pass
extack from error paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass offload flags to the new implementation of
tc_cls_common_offload_init().  Extack will now only
be set if user requested skip_sw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate extack on removal of offloaded filter.  Don't pass
extack from error paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass offload flags to the new implementation of
tc_cls_common_offload_init().  Extack will now only
be set if user requested skip_sw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate extack on removal of offloaded filter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass offload flags to the new implementation of
tc_cls_common_offload_init().  Extack will now only
be set if user requested skip_sw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cls_bpf now guarantees that only device-bound programs are
allowed with skip_sw.  The drivers no longer pay attention to
flags on filter load, therefore the bpf_offload member can be
removed.  If flags are needed again they should probably be
added to struct tc_cls_common_offload instead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename the tc_cls_common_offload_init() helper function to
tc_cls_common_offload_init_deprecated() and add a new implementation
which also takes flags argument.  We will only set extack if flags
indicate that offload is forced (skip_sw) otherwise driver errors
should be ignored, as they don't influence the overall filter
installation.

Note that we need the tc_skip_hw() helper for new version, therefore
it is added later in the file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate extack to cls->destroy callbacks when called from
non-error paths.  On error paths pass NULL to avoid overwriting
the failure message.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry Safonov says:

====================
pktgen: Behavior flags fixes

v2:
  o fixed a nitpick from David Miller

There are a bunch of fixes/cleanups/Documentations.
Diffstat says for itself, regardless added docs and missed flag
parameters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't use error-prone-brute-force way.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add macro generated pkt_flag_names array, with a little help of which
the flags can be printed by using an index.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PKT_FALGS macro will be used to add package behavior names definitions
to simplify the code that prints/reads pkg flags.
Sorted the array in order of printing the flags in pktgen_if_show()
Note: Renamed IPSEC_ON => IPSEC for simplicity.

No visible behavior change expected.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o FLOW_SEQ now can be disabled with pgset "flag !FLOW_SEQ"
o FLOW_SEQ and FLOW_RND are antonyms, as it's shown by pktgen_if_show()
o IPSEC now may be disabled

Note, that IPV6 is enabled with dst6/src6 parameters, not with
a flag parameter.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Change process name in ps output: looks like, these days the process
  is named kpktgend_<cpu>, rather than pktgen/<cpu>.
o Use pg_ctrl for start/stop as it can work well with pgset without
  changes to $(PGDEV) variable.
o Clarify a bit needed $(PGDEV) definition for sample scripts and that
  one needs to `source functions.sh`.
o Document how-to unset a behaviour flag, note about history expansion.
o Fix pgset spi parameter value.

Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rahul Lakkireddy says:

====================
cxgb4: fix build error

Patch 1 fixes build error with compiling cudbg_zlib.c when
CONFIG_ZLIB_DEFLATE macro is not defined.

Patch 2 fixes following sparse warning:
"Using plain integer as NULL pointer"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

memset variables to 0 to fix sparse warnings:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_cudbg.c:409:42: sparse: Using
plain integer as NULL pointer

drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:43:47: sparse: Using
plain integer as NULL pointer

Fixes: ad75b7d3 ("cxgb4: implement ethtool dump data operations")
Fixes: 91c1953d ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:39:5: error:
redefinition of 'cudbg_compress_buff'
    int cudbg_compress_buff(struct cudbg_init *pdbg_init,
        ^~~~~~~~~~~~~~~~~~~
   In file included from
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:23:0:
   drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.h:45:19: note: previous
definition of 'cudbg_compress_buff' was here
    static inline int cudbg_compress_buff(struct cudbg_init *pdbg_init,
                      ^~~~~~~~~~~~~~~~~~~

Fixes: 91c1953d ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: socket closing improvements

while the first 2 patches are just small cleanups, the remaing
patches affect socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the peer sends a shutdown WRITE, this should not affect sending
in general, and waiting for send buffer space in particular.
Stop waiting of the local socket for send buffer space only, if peer
signals closing, but not if peer signals just shutdown WRITE.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a socket is closed or shutdown, smc waits for data being transmitted
in certain states. If the state changes during this wait, the close
switch depending on state should be reentered.
In addition, state change is avoided if sending of close or shutdown fails.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Work requests are needed for every ib_post_send(), among them the
ib_post_send() to signal closing. If an smc socket program is cancelled,
the smc connections should be cleaned up, and require sending of closing
signals to the peer. This may fail, if a wait for
a free work request is needed, but is cancelled immediately due to the
cancel interrupt. To guarantee notification of the peer, the wait for
a work request is changed to uninterruptible.

And the area to receive work request completion info with
ib_poll_cq() is cleared first.
And _tx_ variable names are used in the _tx_routines for the
demultiplexing common type in the header.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to wait for confirmation of pending tx requests
for a closing connection, since pending tx slots are dismissed
when finishing a connection.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanup to avoid duplicate code in smc_clcsock_accept().
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanup to consistently exploit the local struct sock definitions.
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
bpf and netdevsim test updates

A number of test improvements (delayed by merges).  Quentin provides
patches for checking printing to the verifier log from the drivers
and validating extack messages are propagated.  There is also a test
for replacing TC filters to avoid adding back the bug Daniel recently
fixed in net and stable.
====================
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel discovered recently I broke TC filter replace (and fixed
it in commit ad9294db ("bpf: fix cls_bpf on filter replace")).
Add a test to make sure it never happens again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make netdevsim print a message to the BPF verifier log buffer when a
program is offloaded.

Then use this message in hardware offload selftests to make sure that
using this buffer actually prints the message to the console for
eBPF hardware offload.

The message is appended after the last instruction is processed with the
verifying function from netdevsim. Output looks like the following:

    $ tc filter add dev foo ingress bpf obj sample_ret0.o \
        sec .text verbose skip_sw

    Prog section '.text' loaded (5)!
     - Type:         3
     - Instructions: 2 (0 over limit)
     - License:

    Verifier analysis:

    0: (b7) r0 = 0
    1: (95) exit
    [netdevsim] Hello from netdevsim!
    processed 2 insns, stack depth 0

"verbose" flag is required to see it in the console since netdevsim does
not throw an error after printing the message.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not compile netdevsim/bpf.c if BPF syscall is not
enabled.  Otherwise bpf core would have to provide wrappers
for all functions offload drivers may call, even though
system will never see a BPF object.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add checks to test that netlink extack messages are correctly displayed
in some expected error cases for eBPF offload to netdevsim with TC and
XDP.

iproute2 may be built without libmnl support, in which case the extack
messages will not be reported.  Try to detect this condition, and when
enountered print a mild warning to the user and skip the extack validation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the recently added extack support for TC eBPF filters in netdevsim.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2018-01-23

This series contains updates to i40e and i40evf only.

Pawel enables FlatNVM support on x722 devices by allowing nvmupdate tool
to configure the preservation flags in the AdminQ command.

Mitch fixes a potential divide by zero error when DCB is enabled and
the firmware fails to configure the VSI, so check for this state.
Fixed a bug where the driver could fail to adhere to ETS bandwidth
allocations if 8 traffic classes were configured on the switch.

Sudheer fixes a potential deadlock by avoiding to call
flush_schedule_work() in i40evf_remove(), since cancel_work_sync()
and cancel_delayed_work_sync() already cleans up necessary work items.
Fixed an issue with the problematic detection and recovery from
hung queues in the PF which was causing lost interrupts.  This is done
by triggering a software interrupt so that interrupts are forced on
and if we are already in napi_poll and an interrupt fires, napi_poll
will not be rescheduled and the interrupt is lost.

Avinash fixes an issue in the VF where is was possible to issue a
reset_task while the device is currently being removed.

Michal fixes an issue occurring while calling i40e_led_set() with
the blink parameter set to true, which was causing the activity LED
instead of the link LED to blink for port identification.

Shiraz changes the client interface to not call client close/open on
netdev down/up events, since this causes a lot of thrash that is
not needed.  Instead, disable the PE TCP-ENA flag during a netdev
down event and re-enable on a netdev up event, since this blocks all
TCP traffic to the RDMA protocol engine.

Alan fixes an issue which was causing a potential transmit hang by
ignoring the PF link up message if the VF state is not yet in the
RUNNING state.

Amritha fixes the channel VSI recreation during the reset flow to
reconfigure the transmit rings and the queue context associated with
the channel VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Davide Caratti says:

====================
net/sched: remove spinlock from 'csum' action

Similarly to what has been done earlier with other actions [1][2], this
series tries to improve the performance of 'csum' tc action, removing a
spinlock in the data path. Patch 1 lets act_csum use per-CPU counters;
patch 2 removes spin_{,un}lock_bh() calls from the act() method.

test procedure (using pktgen from https://github.com/netoptimizer):

 # ip link add name eth1 type dummy
 # ip link set dev eth1 up
 # tc qdisc add dev eth1 root handle 1: prio
 # for a in pass drop; do
 > tc filter del dev eth1 parent 1: pref 10 matchall action csum udp
 > tc filter add dev eth1 parent 1: pref 10 matchall action csum udp $a
 > for n in 2 4; do
 > ./pktgen_bench_xmit_mode_queue_xmit.sh -v -s 64 -t $n -n 1000000 -i eth1
 > done
 > done

test results:

      |    |  before patch   |   after patch
  $a  | $n | avg. pps/thread | avg. pps/thread
 -----+----+-----------------+----------------
 pass |  2 |    1671463 ± 4% |    1920789 ± 3%
 pass |  4 |     648797 ± 1% |     738190 ± 1%
 drop |  2 |    3212692 ± 2% |    3719811 ± 2%
 drop |  4 |    1078824 ± 1% |    1328099 ± 1%

references:

[1] https://www.spinics.net/lists/netdev/msg334760.html
[2] https://www.spinics.net/lists/netdev/msg465862.html

v3 changes:
 - use rtnl_dereference() in place of rcu_dereference() in tcf_csum_dump()

v2 changes:
 - add 'drop' test, it produces more contentions
 - use RCU-protected struct to store 'action' and 'update_flags', to avoid
   reading the values from subsequent configurations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

use RCU instead of spin_{,unlock}_bh() to protect concurrent read/write on
act_csum configuration, to reduce the effects of contention in the data
path when multiple readers are present.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use per-CPU counters, like other TC actions do, instead of maintaining one
set of stats across all cores. This allows updating act_csum stats without
the need of protecting them using spin_{,un}lock_bh() invocations.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>