1. 23 May, 2019 30 commits
    • Jiri Pirko's avatar
      devlink: add warning in case driver does not set port type · 136bf27f
      Jiri Pirko authored
      Prevent misbehavior of drivers who would not set port type for longer
      period of time. Drivers should always set port type. Do WARN if that
      happens.
      
      Note that it is perfectly fine to temporarily not have the type set,
      during initialization and port type change.
      Signed-off-by: default avatarJiri Pirko <jiri@mellanox.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      136bf27f
    • Sunil Muthuswamy's avatar
      hv_sock: perf: loop in send() to maximize bandwidth · 14a1eaa8
      Sunil Muthuswamy authored
      Currently, the hv_sock send() iterates once over the buffer, puts data into
      the VMBUS channel and returns. It doesn't maximize on the case when there
      is a simultaneous reader draining data from the channel. In such a case,
      the send() can maximize the bandwidth (and consequently minimize the cpu
      cycles) by iterating until the channel is found to be full.
      
      Perf data:
      Total Data Transfer: 10GB/iteration
      Single threaded reader/writer, Linux hvsocket writer with Windows hvsocket
      reader
      Packet size: 64KB
      CPU sys time was captured using the 'time' command for the writer to send
      10GB of data.
      'Send Buffer Loop' is with the patch applied.
      The values below are over 10 iterations.
      
      |--------------------------------------------------------|
      |        |        Current        |   Send Buffer Loop    |
      |--------------------------------------------------------|
      |        | Throughput | CPU sys  | Throughput | CPU sys  |
      |        | (MB/s)     | time (s) | (MB/s)     | time (s) |
      |--------------------------------------------------------|
      | Min    |     407    |   7.048  |    401     |  5.958   |
      |--------------------------------------------------------|
      | Max    |     455    |   7.563  |    542     |  6.993   |
      |--------------------------------------------------------|
      | Avg    |     440    |   7.411  |    451     |  6.639   |
      |--------------------------------------------------------|
      | Median |     446    |   7.417  |    447     |  6.761   |
      |--------------------------------------------------------|
      
      Observation:
      1. The avg throughput doesn't really change much with this change for this
      scenario. This is most probably because the bottleneck on throughput is
      somewhere else.
      2. The average system (or kernel) cpu time goes down by 10%+ with this
      change, for the same amount of data transfer.
      Signed-off-by: default avatarSunil Muthuswamy <sunilmut@microsoft.com>
      Reviewed-by: default avatarDexuan Cui <decui@microsoft.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      14a1eaa8
    • Sunil Muthuswamy's avatar
      hv_sock: perf: Allow the socket buffer size options to influence the actual socket buffers · ac383f58
      Sunil Muthuswamy authored
      Currently, the hv_sock buffer size is static and can't scale to the
      bandwidth requirements of the application. This change allows the
      applications to influence the socket buffer sizes using the SO_SNDBUF and
      the SO_RCVBUF socket options.
      
      Few interesting points to note:
      1. Since the VMBUS does not allow a resize operation of the ring size, the
      socket buffer size option should be set prior to establishing the
      connection for it to take effect.
      2. Setting the socket option comes with the cost of that much memory being
      reserved/allocated by the kernel, for the lifetime of the connection.
      
      Perf data:
      Total Data Transfer: 1GB
      Single threaded reader/writer
      Results below are summarized over 10 iterations.
      
      Linux hvsocket writer + Windows hvsocket reader:
      |---------------------------------------------------------------------------------------------|
      |Packet size ->   |      128B       |       1KB       |       4KB       |        64KB         |
      |---------------------------------------------------------------------------------------------|
      |SO_SNDBUF size | |                 Throughput in MB/s (min/max/avg/median):                  |
      |               v |                                                                           |
      |---------------------------------------------------------------------------------------------|
      |      Default    | 109/118/114/116 | 636/774/701/700 | 435/507/480/476 |   410/491/462/470   |
      |      16KB       | 110/116/112/111 | 575/705/662/671 | 749/900/854/869 |   592/824/692/676   |
      |      32KB       | 108/120/115/115 | 703/823/767/772 | 718/878/850/866 | 1593/2124/2000/2085 |
      |      64KB       | 108/119/114/114 | 592/732/683/688 | 805/934/903/911 | 1784/1943/1862/1843 |
      |---------------------------------------------------------------------------------------------|
      
      Windows hvsocket writer + Linux hvsocket reader:
      |---------------------------------------------------------------------------------------------|
      |Packet size ->   |     128B    |      1KB        |          4KB        |        64KB         |
      |---------------------------------------------------------------------------------------------|
      |SO_RCVBUF size | |               Throughput in MB/s (min/max/avg/median):                    |
      |               v |                                                                           |
      |---------------------------------------------------------------------------------------------|
      |      Default    | 69/82/75/73 | 313/343/333/336 |   418/477/446/445   |   659/701/676/678   |
      |      16KB       | 69/83/76/77 | 350/401/375/382 |   506/548/517/516   |   602/624/615/615   |
      |      32KB       | 62/83/73/73 | 471/529/496/494 |   830/1046/935/939  | 944/1180/1070/1100  |
      |      64KB       | 64/70/68/69 | 467/533/501/497 | 1260/1590/1430/1431 | 1605/1819/1670/1660 |
      |---------------------------------------------------------------------------------------------|
      Signed-off-by: default avatarSunil Muthuswamy <sunilmut@microsoft.com>
      Reviewed-by: default avatarDexuan Cui <decui@microsoft.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ac383f58
    • Eric Dumazet's avatar
      ipv4/igmp: shrink struct ip_sf_list · 0db355d4
      Eric Dumazet authored
      Removing two 4 bytes holes allows to use kmalloc-32
      kmem cache instead of kmalloc-64 on 64bit kernels.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0db355d4
    • David Ahern's avatar
      neighbor: Add tracepoint to __neigh_create · fc651001
      David Ahern authored
      Add tracepoint to __neigh_create to enable debugging of new entries.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      fc651001
    • David Ahern's avatar
      selftests: pmtu: Simplify cleanup and namespace names · a92a0a7b
      David Ahern authored
      The point of the pause-on-fail argument is to leave the setup as is after
      a test fails to allow a user to debug why it failed. Move the cleanup
      after posting the result to the user to make it so.
      
      Random names for the namespaces are not user friendly when trying to
      debug a failure. Make them simpler and more direct for the tests. Run
      cleanup at the beginning to ensure they are cleaned up if they already
      exist.
      
      Remove cleanup_done. There is no harm in doing cleanup twice; just
      ignore any errors related to not existing - which is already done.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a92a0a7b
    • David Ahern's avatar
      selftests: fib-onlink: Make quiet by default · 9b7e94e6
      David Ahern authored
      Add VERBOSE argument to fib-onlink-tests.sh and make output quiet by
      default. Add getopt parsing of inputs and support for -v (verbose) and
      -p (pause on fail).
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      9b7e94e6
    • David Ahern's avatar
      net: Set strict_start_type for routes and rules · 75425657
      David Ahern authored
      New userspace on an older kernel can send unknown and unsupported
      attributes resulting in an incompelete config which is almost
      always wrong for routing (few exceptions are passthrough settings
      like the protocol that installed the route).
      
      Set strict_start_type in the policies for IPv4 and IPv6 routes and
      rules to detect new, unsupported attributes and fail the route add.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      75425657
    • David S. Miller's avatar
      Merge branch 'net-Export-functions-for-nexthop-code' · e38f7cbd
      David S. Miller authored
      David Ahern says:
      
      ====================
      net: Export functions for nexthop code
      
      This set exports ipv4 and ipv6 fib functions for use by the nexthop
      code. It also adds new ones to send route notifications if a nexthop
      configuration changes.
      
      v2
      - repost of patches dropped at the end of the last dev window
        added patch 8 which exports nh_update_mtu since it is inline with
        the other patches
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e38f7cbd
    • David Ahern's avatar
      ipv4: Rename and export nh_update_mtu · 06c77c3e
      David Ahern authored
      Rename nh_update_mtu to fib_nhc_update_mtu and export for use by the
      nexthop code.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      06c77c3e
    • David Ahern's avatar
      ipv4: export fib_info_update_nh_saddr · c3669486
      David Ahern authored
      Add scope as input argument versus relying on fib_info reference in
      fib_nh, and export fib_info_update_nh_saddr.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c3669486
    • David Ahern's avatar
      ipv4: export fib_flush · 9bd83667
      David Ahern authored
      As nexthops are deleted, fib entries referencing it are marked dead.
      Export fib_flush so those entries can be removed in a timely manner.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      9bd83667
    • David Ahern's avatar
      ipv4: export fib_check_nh · ac1fab2d
      David Ahern authored
      Change fib_check_nh to take net, table and scope as input arguments
      over struct fib_config and export for use by nexthop code.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ac1fab2d
    • David Ahern's avatar
      ipv4: Add function to send route updates · 1bff1a0c
      David Ahern authored
      Add fib_info_notify_update to walk the fib and send RTM_NEWROUTE
      notifications with NLM_F_REPLACE set for entries linked to a fib_info
      that have nh_updated flag set. This helper will be used by the nexthop
      code to notify userspace of routes that are impacted when a nexthop
      config is updated via replace. The new function and its helper are
      similar to how fib_flush and fib_table_flush work for address delete
      and link down events.
      
      This notification is needed for legacy apps that do not understand
      the new nexthop object. Apps that are nexthop aware can use the
      RTA_NH_ID attribute in the route notification to just ignore it.
      
      In the future this should be wrapped in a sysctl to allow OS'es that
      are fully updated to avoid the notificaton storm.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      1bff1a0c
    • David Ahern's avatar
      ipv6: export function to send route updates · 19a3b7ee
      David Ahern authored
      Add fib6_rt_update to send RTM_NEWROUTE with NLM_F_REPLACE set. This
      helper will be used by the nexthop code to notify userspace of routes
      that are impacted when a nexthop config is updated via replace.
      
      This notification is needed for legacy apps that do not understand
      the new nexthop object. Apps that are nexthop aware can use the
      RTA_NH_ID attribute in the route notification to just ignore it.
      
      In the future this should be wrapped in a sysctl to allow OS'es that
      are fully updated to avoid the notificaton storm.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      19a3b7ee
    • David Ahern's avatar
      ipv6: Add hook to bump sernum for a route to stubs · cdaa16a4
      David Ahern authored
      Add hook to ipv6 stub to bump the sernum up to the root node for a
      route. This is needed by the nexthop code when a nexthop config changes.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      cdaa16a4
    • David Ahern's avatar
      ipv6: Add delete route hook to stubs · 68a9b13d
      David Ahern authored
      Add ip6_del_rt to the IPv6 stub. The hook is needed by the nexthop
      code to remove entries linked to a nexthop that is getting deleted.
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      68a9b13d
    • David S. Miller's avatar
      Merge branch 'net-phy-T1-support' · 26b1b8d7
      David S. Miller authored
      Andrew Lunn says:
      
      ====================
      net: phy: T1 support
      
      T1 PHYs make use of a single twisted pair, rather than the traditional
      2 pair for 100BaseT or 4 pair for 1000BaseT. This patchset adds link
      modes for 100BaseT1 and 1000BaseT1, and them makes use of 100BaseT1 in
      the list of PHY features used by current T1 drivers.
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      26b1b8d7
    • Andrew Lunn's avatar
      net: phy: Make phy_basic_t1_features use base100t1. · e5fb32c6
      Andrew Lunn authored
      Now that there is a link mode for 100BaseT1, use it in
      phy_basic_t1_features so T1 PHY drivers will indicate this mode via
      the Ethtool API.
      Signed-off-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e5fb32c6
    • Andrew Lunn's avatar
      net: phy: Add support for 100BaseT1 and 1000BaseT1 · b2557764
      Andrew Lunn authored
      Add link modes for 100Mbps and 1Gbps over a single pair.
      Signed-off-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      b2557764
    • Trent Piepho's avatar
      net: phy: dp83867: Allocate state struct in probe · 565d9d22
      Trent Piepho authored
      This was being done in config the first time the phy was configured.
      Should be in the probe method.
      
      Cc: Andrew Lunn <andrew@lunn.ch>
      Cc: Florian Fainelli <f.fainelli@gmail.com>
      Cc: Heiner Kallweit <hkallweit1@gmail.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      565d9d22
    • Trent Piepho's avatar
      net: phy: dp83867: Validate FIFO depth property · f8bbf417
      Trent Piepho authored
      Insure property is in valid range and fail when reading DT if it is not.
      Also add error message for existing failure if required property is not
      present.
      
      Cc: Andrew Lunn <andrew@lunn.ch>
      Cc: Florian Fainelli <f.fainelli@gmail.com>
      Cc: Heiner Kallweit <hkallweit1@gmail.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f8bbf417
    • Trent Piepho's avatar
      net: phy: dp83867: IO impedance is not dependent on RGMII delay · 27708eb5
      Trent Piepho authored
      The driver would only set the IO impedance value when RGMII internal
      delays were enabled.  There is no reason for this.  Move the IO
      impedance block out of the RGMII delay block.
      
      Cc: Andrew Lunn <andrew@lunn.ch>
      Cc: Florian Fainelli <f.fainelli@gmail.com>
      Cc: Heiner Kallweit <hkallweit1@gmail.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      27708eb5
    • Trent Piepho's avatar
      net: phy: dp83867: Use unsigned variables to store unsigned properties · 1b9b2954
      Trent Piepho authored
      The variables used to store u32 DT properties were signed ints.  This
      doesn't work properly if the value of the property were to overflow.
      Use unsigned variables so this doesn't happen.
      
      Cc: Andrew Lunn <andrew@lunn.ch>
      Cc: Florian Fainelli <f.fainelli@gmail.com>
      Cc: Heiner Kallweit <hkallweit1@gmail.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      1b9b2954
    • Trent Piepho's avatar
      net: phy: dp83867: Rework delay rgmii delay handling · c11669a2
      Trent Piepho authored
      The code was assuming the reset default of the delay control register
      was to have delay disabled.  This is what the datasheet shows as the
      register's initial value.  However, that's not actually true: the
      default is controlled by the PHY's pin strapping.
      
      If the interface mode is selected as RX or TX delay only, insure the
      other direction's delay is disabled.
      
      If the interface mode is just "rgmii", with neither TX or RX internal
      delay, one might expect that the driver should disable both delays.  But
      this is not what the driver does.  It leaves the setting at the PHY's
      strapping's default.  And that default, for no pins with strapping
      resistors, is to have delay enabled and 2.00 ns.
      
      Rather than change this behavior, I've kept it the same and documented
      it.  No delay will most likely not work and will break ethernet on any
      board using "rgmii" mode.  If the board is strapped to have a delay and
      is configured to use "rgmii" mode a warning is generated that "rgmii-id"
      should have been used.
      
      Also validate the delay values and fail if they are not in range.
      
      Cc: Andrew Lunn <andrew@lunn.ch>
      Cc: Florian Fainelli <f.fainelli@gmail.com>
      Cc: Heiner Kallweit <hkallweit1@gmail.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c11669a2
    • Trent Piepho's avatar
      net: phy: dp83867: Add ability to disable output clock · 13c83cf8
      Trent Piepho authored
      Generally, the output clock pin is only used for testing and only serves
      as a source of RF noise after this.  It could be used to daisy-chain
      PHYs, but this is uncommon.  Since the PHY can disable the output, make
      doing so an option.  I do this by adding another enumeration to the
      allowed values of ti,clk-output-sel.
      
      The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
      expect: to select the REF_CLK as the output.  Rather it meant "keep
      clock output setting as is", which, depending on PHY strapping, might
      not be outputting REF_CLK.
      
      Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
      Omitting the property will leave the setting as is (which was the
      previous behavior in this case).
      
      Out of range values were silently converted into
      DP83867_CLK_O_SEL_REF_CLK.  Change this so they generate an error.
      
      Cc: Andrew Lunn <andrew@lunn.ch>
      Cc: Florian Fainelli <f.fainelli@gmail.com>
      Cc: Heiner Kallweit <hkallweit1@gmail.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      13c83cf8
    • Trent Piepho's avatar
      dt-bindings: phy: dp83867: Add documentation for disabling clock output · 980066e6
      Trent Piepho authored
      The clock output is generally only used for testing and development and
      not used to daisy-chain PHYs.  It's just a source of RF noise afterward.
      
      Add a mux value for "off".  I've added it as another enumeration to the
      output property.  In the actual PHY, the mux and the output enable are
      independently controllable.  However, it doesn't seem useful to be able
      to describe the mux setting when the output is disabled.
      
      Document that PHY's default setting will be left as is if the property
      is omitted.
      
      Cc: Rob Herring <robh+dt@kernel.org>
      Cc: Mark Rutland <mark.rutland@arm.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      980066e6
    • Trent Piepho's avatar
      dt-bindings: phy: dp83867: Describe how driver behaves w.r.t rgmii delay · 9c3f3410
      Trent Piepho authored
      Add a note to make it more clear how the driver behaves when "rgmii" vs
      "rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected.
      
      Cc: Rob Herring <robh+dt@kernel.org>
      Cc: Mark Rutland <mark.rutland@arm.com>
      Signed-off-by: default avatarTrent Piepho <tpiepho@impinj.com>
      Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      9c3f3410
    • Vishal Kulkarni's avatar
      cxgb4: Enable hash filter with offload · 74dd5aa1
      Vishal Kulkarni authored
      Hash (exact-match) filters used for offloading flows share the
      same active region resources on the chip with upper layer drivers,
      like iw_cxgb4, chcr, etc. Currently, only either Hash filters
      or ULDs can use the active region resources, but not both. Hence,
      use the new firmware configuration parameters (when available)
      to allow both the Hash filters and ULDs to share the
      active region simultaneously.
      Signed-off-by: default avatarVishal Kulkarni <vishal@chelsio.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      74dd5aa1
    • Baruch Siach's avatar
      net: fec: remove redundant ipg clock disable · 2bb0f3b4
      Baruch Siach authored
      Don't disable the ipg clock in the regulator error path. The clock is
      disable unconditionally two lines below the failed_regulator label.
      Signed-off-by: default avatarBaruch Siach <baruch@tkos.co.il>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2bb0f3b4
  2. 22 May, 2019 6 commits
    • Felipe Gasper's avatar
      net: Add UNIX_DIAG_UID to Netlink UNIX socket diagnostics. · cae9910e
      Felipe Gasper authored
      This adds the ability for Netlink to report a socket's UID along with the
      other UNIX diagnostic information that is already available. This will
      allow diagnostic tools greater insight into which users control which
      socket.
      
      To test this, do the following as a non-root user:
      
          unshare -U -r bash
          nc -l -U user.socket.$$ &
      
      .. and verify from within that same session that Netlink UNIX socket
      diagnostics report the socket's UID as 0. Also verify that Netlink UNIX
      socket diagnostics report the socket's UID as the user's UID from an
      unprivileged process in a different session. Verify the same from
      a root process.
      Signed-off-by: default avatarFelipe Gasper <felipe@felipegasper.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      cae9910e
    • Linus Torvalds's avatar
      Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux · 54dee406
      Linus Torvalds authored
      Pull arm64 fixes from Will Deacon:
      
       - Fix SPE probe failure when backing auxbuf with high-order pages
      
       - Fix handling of DMA allocations from outside of the vmalloc area
      
       - Fix generation of build-id ELF section for vDSO object
      
       - Disable huge I/O mappings if kernel page table dumping is enabled
      
       - A few other minor fixes (comments, kconfig etc)
      
      * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
        arm64: vdso: Explicitly add build-id option
        arm64/mm: Inhibit huge-vmap with ptdump
        arm64: Print physical address of page table base in show_pte()
        arm64: don't trash config with compat symbol if COMPAT is disabled
        arm64: assembler: Update comment above cond_yield_neon() macro
        drivers/perf: arm_spe: Don't error on high-order pages for aux buf
        arm64/iommu: handle non-remapped addresses in ->mmap and ->get_sgtable
      54dee406
    • Linus Torvalds's avatar
      Merge tag 'gfs2-5.1.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2 · 651bae98
      Linus Torvalds authored
      Pull gfs2 fix from Andreas Gruenbacher:
       "Fix a gfs2 sign extension bug introduced in v4.3"
      
      * tag 'gfs2-5.1.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
        gfs2: Fix sign extension bug in gfs2_update_stats
      651bae98
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · f75b6f30
      Linus Torvalds authored
      Pull networking fixes from David Miller:
      
       1) Clear up some recent tipc regressions because of registration
          ordering. Fix from Junwei Hu.
      
       2) tipc's TLV_SET() can read past the end of the supplied buffer during
          the copy. From Chris Packham.
      
       3) ptp example program doesn't match the kernel, from Richard Cochran.
      
       4) Outgoing message type fix in qrtr, from Bjorn Andersson.
      
       5) Flow control regression in stmmac, from Tan Tee Min.
      
       6) Fix inband autonegotiation in phylink, from Russell King.
      
       7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
      
       8) Fix usbnet crash after disconnect, from Kloetzke Jan.
      
      * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
        usbnet: fix kernel crash after disconnect
        selftests: fib_rule_tests: use pre-defined DEV_ADDR
        net-next: net: Fix typos in ip-sysctl.txt
        ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
        net: phylink: ensure inband AN works correctly
        usbnet: ipheth: fix racing condition
        net: stmmac: dma channel control register need to be init first
        net: stmmac: fix ethtool flow control not able to get/set
        net: qrtr: Fix message type of outgoing packets
        networking: : fix typos in code comments
        ptp: Fix example program to match kernel.
        fddi: fix typos in code comments
        selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
        selftests: fib_rule_tests: fix local IPv4 address typo
        tipc: Avoid copying bytes beyond the supplied data
        2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
        1/2] net: axienet: use readx_poll_timeout() in mdio wait function
        vlan: Mark expected switch fall-through
        macvlan: Mark expected switch fall-through
        net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
        ...
      f75b6f30
    • Linus Torvalds's avatar
      Merge tag 'for-5.2/dm-fix-1' of... · 86f9e56d
      Linus Torvalds authored
      Merge tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
      
      Pull device mapper fix from Mike Snitzer:
       "Fix a particularly glaring oversight in a DM core commit from 5.1 that
        doesn't properly trim special IOs (e.g. discards) relative to
        corresponding target's max_io_len_target_boundary()"
      
      * tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
        dm: make sure to obey max_io_len_target_boundary
      86f9e56d
    • Andreas Gruenbacher's avatar
      gfs2: Fix sign extension bug in gfs2_update_stats · 5a5ec83d
      Andreas Gruenbacher authored
      Commit 4d207133 changed the types of the statistic values in struct
      gfs2_lkstats from s64 to u64.  Because of that, what should be a signed
      value in gfs2_update_stats turned into an unsigned value.  When shifted
      right, we end up with a large positive value instead of a small negative
      value, which results in an incorrect variance estimate.
      
      Fixes: 4d207133 ("gfs2: Make statistics unsigned, suitable for use with do_div()")
      Signed-off-by: default avatarAndreas Gruenbacher <agruenba@redhat.com>
      Cc: stable@vger.kernel.org # v4.4+
      5a5ec83d
  3. 21 May, 2019 4 commits
    • Michael Lass's avatar
      dm: make sure to obey max_io_len_target_boundary · 51b86f9a
      Michael Lass authored
      Commit 61697a6a ("dm: eliminate 'split_discard_bios' flag from DM
      target interface") incorrectly removed code from
      __send_changing_extent_only() that is required to impose a per-target IO
      boundary on IO that exceeds max_io_len_target_boundary().  Otherwise
      "special" IO (e.g. DISCARD, WRITE SAME, WRITE ZEROES) can write beyond
      where allowed.
      
      Fix this by restoring the max_io_len_target_boundary() limit in
      __send_changing_extent_only()
      
      Fixes: 61697a6a ("dm: eliminate 'split_discard_bios' flag from DM target interface")
      Cc: stable@vger.kernel.org # 5.1+
      Signed-off-by: default avatarMichael Lass <bevan@bi-co.net>
      Signed-off-by: default avatarMike Snitzer <snitzer@redhat.com>
      51b86f9a
    • Kloetzke Jan's avatar
      usbnet: fix kernel crash after disconnect · ad70411a
      Kloetzke Jan authored
      When disconnecting cdc_ncm the kernel sporadically crashes shortly
      after the disconnect:
      
        [   57.868812] Unable to handle kernel NULL pointer dereference at virtual address 00000000
        ...
        [   58.006653] PC is at 0x0
        [   58.009202] LR is at call_timer_fn+0xec/0x1b4
        [   58.013567] pc : [<0000000000000000>] lr : [<ffffff80080f5130>] pstate: 00000145
        [   58.020976] sp : ffffff8008003da0
        [   58.024295] x29: ffffff8008003da0 x28: 0000000000000001
        [   58.029618] x27: 000000000000000a x26: 0000000000000100
        [   58.034941] x25: 0000000000000000 x24: ffffff8008003e68
        [   58.040263] x23: 0000000000000000 x22: 0000000000000000
        [   58.045587] x21: 0000000000000000 x20: ffffffc68fac1808
        [   58.050910] x19: 0000000000000100 x18: 0000000000000000
        [   58.056232] x17: 0000007f885aff8c x16: 0000007f883a9f10
        [   58.061556] x15: 0000000000000001 x14: 000000000000006e
        [   58.066878] x13: 0000000000000000 x12: 00000000000000ba
        [   58.072201] x11: ffffffc69ff1db30 x10: 0000000000000020
        [   58.077524] x9 : 8000100008001000 x8 : 0000000000000001
        [   58.082847] x7 : 0000000000000800 x6 : ffffff8008003e70
        [   58.088169] x5 : ffffffc69ff17a28 x4 : 00000000ffff138b
        [   58.093492] x3 : 0000000000000000 x2 : 0000000000000000
        [   58.098814] x1 : 0000000000000000 x0 : 0000000000000000
        ...
        [   58.205800] [<          (null)>]           (null)
        [   58.210521] [<ffffff80080f5298>] expire_timers+0xa0/0x14c
        [   58.215937] [<ffffff80080f542c>] run_timer_softirq+0xe8/0x128
        [   58.221702] [<ffffff8008081120>] __do_softirq+0x298/0x348
        [   58.227118] [<ffffff80080a6304>] irq_exit+0x74/0xbc
        [   58.232009] [<ffffff80080e17dc>] __handle_domain_irq+0x78/0xac
        [   58.237857] [<ffffff8008080cf4>] gic_handle_irq+0x80/0xac
        ...
      
      The crash happens roughly 125..130ms after the disconnect. This
      correlates with the 'delay' timer that is started on certain USB tx/rx
      errors in the URB completion handler.
      
      The problem is a race of usbnet_stop() with usbnet_start_xmit(). In
      usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in
      flight. This only makes sense if no new URBs are submitted
      concurrently, though. But the usbnet_start_xmit() can run at the same
      time on another CPU which almost unconditionally submits an URB. The
      error callback of the new URB will then schedule the timer after it was
      already stopped.
      
      The fix adds a check if the tx queue is stopped after the tx list lock
      has been taken. This should reliably prevent the submission of new URBs
      while usbnet_terminate_urbs() does its job. The same thing is done on
      the rx side even though it might be safe due to other flags that are
      checked there.
      Signed-off-by: default avatarJan Klötzke <Jan.Kloetzke@preh.de>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ad70411a
    • Hangbin Liu's avatar
      selftests: fib_rule_tests: use pre-defined DEV_ADDR · 34632975
      Hangbin Liu authored
      DEV_ADDR is defined but not used. Use it in address setting.
      Do the same with IPv6 for consistency.
      Reported-by: default avatarDavid Ahern <dsahern@gmail.com>
      Fixes: fc82d93e ("selftests: fib_rule_tests: fix local IPv4 address typo")
      Signed-off-by: default avatarHangbin Liu <liuhangbin@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      34632975
    • Masanari Iida's avatar
      net-next: net: Fix typos in ip-sysctl.txt · 2bcd9d84
      Masanari Iida authored
      This patch fixes some spelling typos found in ip-sysctl.txt
      Signed-off-by: default avatarMasanari Iida <standby24x7@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2bcd9d84