Skip to content

L
linux
Switch branch/tag
  1. 16 Feb, 2020 6 commits
    • Brett Creeley's avatar
      ice: Add support to enable/disable all Rx queues before waiting · 13a6233b
      Brett Creeley authored 
      Currently when we enable/disable all Rx queues we do the following
sequence for each Rx queue and then move to the next queue.

1. Enable/Disable the Rx queue via register write.
2. Read the configuration register to determine if the Rx queue was
enabled/disabled successfully.

In some cases enabling/disabling queue 0 fails because of step 2 above.
Fix this by doing step 1 for all of the Rx queues and then step 2 for
all of the Rx queues.

Also, there are cases where we enable/disable a single queue (i.e.
SR-IOV and XDP) so add a new function that does step 1 and 2 above with
a read flush in between.

This change also required a single Rx queue to be enabled/disabled with
and without waiting for the change to propagate through hardware. Fix
this by adding a boolean wait flag to the necessary functions.

Also, add the keywords "one" and "all" to distinguish between
enabling/disabling a single Rx queue and all Rx queues respectively.
Signed-off-by: default avatarBrett Creeley <brett.creeley@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      13a6233b
    • Brett Creeley's avatar
      ice: Only allow tagged bcast/mcast traffic for VF in port VLAN · 72634bc2
      Brett Creeley authored 
      Currently the VF can see other's broadcast and multicast traffic because
it always has a VLAN filter for VLAN 0. Fix this by removing/adding the
VF's VLAN 0 filter when a port VLAN is added/removed respectively.

This required a few changes.

1. Move where we add VLAN 0 by default for the VF into
ice_alloc_vsi_res() because this is when we determine if a port VLAN is
present for load and reset.

2. Moved where we kill the old port VLAN filter in
ice_set_vf_port_vlan() to the very end of the function because it allows
us to save the old port VLAN configuration upon any failure case.

3. During adding/removing of a port VLAN via ice_set_vf_port_vlan() we
also need to remove/add the VLAN 0 filter rule respectively.

4. Improve log messages.
Signed-off-by: default avatarBrett Creeley <brett.creeley@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      72634bc2
    • Brett Creeley's avatar
      ice: Fix Port VLAN priority bits · 61c9ce86
      Brett Creeley authored 
      Currently when configuring a port VLAN for a VF we are only shifting the
QoS bits by 12. This is incorrect. Fix this by getting rid of the ICE
specific VLAN defines and use the kernel VLAN defines instead.

Also, don't assign a value to vlanprio until the VLAN ID and QoS
parameters have been validated.

Also, there are many places we do (le16_to_cpu(vsi->info.pvid) &
VLAN_VID_MASK). Instead do (vf->port_vlan_info & VLAN_VID_MASK) because
we always save what's stored in vsi->info.pvid to vf->port_vlan_info in
the CPU's endianness.
Signed-off-by: default avatarBrett Creeley <brett.creeley@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      61c9ce86
    • Brett Creeley's avatar
      ice: Add helper to determine if VF link is up · 0b6c6a8b
      Brett Creeley authored 
      The check for vf->link_up is incorrect because this field is only valid if
vf->link_forced is true. Fix this by adding the helper ice_is_vf_link_up()
to determine if the VF's link is up.
Signed-off-by: default avatarBrett Creeley <brett.creeley@intel.com>
Signed-off-by: default avatarTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      0b6c6a8b
    • Brett Creeley's avatar
      ice: Refactor port vlan configuration for the VF · b093841f
      Brett Creeley authored 
      Currently ice_vsi_manage_pvid() calls
ice_vsi_[set|kill]_pvid_fill_ctxt() when enabling/disabling a port VLAN
on a VSI respectively. These two functions have some duplication so just
move their unique pieces inline in ice_vsi_manage_pvid() and then the
duplicate code can be reused for both the enabling/disabling paths.

Before this patch the info.pvid field was not being written
correctly via ice_vsi_kill_pvid_fill_ctxt() so it was being hard coded
to 0 in ice_set_vf_port_vlan(). Fix this by setting the info.pvid field
to 0 before calling ice_vsi_update() in ice_vsi_manage_pvid().

We currently use vf->port_vlan_id to keep track of the port VLAN
ID and QoS, which is a bit misleading. Fix this by renaming it to
vf->port_vlan_info. Also change the name of the argument for
ice_vsi_manage_pvid() from vid to pvid_info.

In ice_vsi_manage_pvid() only save the fields that were modified
in the VSI properties structure on success instead of the entire thing.
Signed-off-by: default avatarBrett Creeley <brett.creeley@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      b093841f
    • Brett Creeley's avatar
      ice: Add initial support for QinQ · 42f3efef
      Brett Creeley authored 
      Allow support for S-Tag + C-Tag VLAN traffic by disabling pruning when
there are no 0x8100 VLAN interfaces currently created on top of the PF.
When an 0x8100 VLAN interface is configured, enable pruning and only
support single and double C-Tag VLAN traffic. If all of the 0x8100
interfaces that were created on top of the PF are removed via
ethtool -K <iface> rx-vlan-filter off or via ip tools, then disable
pruning and allow S-Tag + C-Tag traffic again.

Add VLAN 0 filter by default for the PF. This is because a bridge
sets the default_pvid to 1, sends the request down to
ice_vlan_rx_add_vid(), and we never get the request to add VLAN 0 via
the 8021q module which causes all untagged traffic to be dropped.
Signed-off-by: default avatarBrett Creeley <brett.creeley@intel.com>
Signed-off-by: default avatarTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      42f3efef
  3. 14 Feb, 2020 24 commits
  5. 13 Feb, 2020 10 commits
    • Linus Torvalds's avatar
      Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux · b19e8c68
      Linus Torvalds authored 
      Pull arm64 fixes from Will Deacon:
 "Summary below, but it's all reasonably straightforward. There are some
  more fixes on the horizon, but nothing disastrous yet.

  Summary:

   - Fix build when KASLR is enabled but CONFIG_ARCH_RANDOM is not set

   - Fix context-switching of SSBS state on systems that implement it

   - Fix spinlock compiler warning introduced during the merge window

   - Fix incorrect header inclusion (linux/clk-provider.h)

   - Use SYSCTL_{ZERO,ONE} instead of rolling our own static variables

   - Don't scream if optional SMMUv3 PMU irq is missing

   - Remove some unused function prototypes"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: time: Replace <linux/clk-provider.h> by <linux/of_clk.h>
  arm64: Fix CONFIG_ARCH_RANDOM=n build
  perf/smmuv3: Use platform_get_irq_optional() for wired interrupt
  arm64/spinlock: fix a -Wunused-function warning
  arm64: ssbs: Fix context-switch when SSBS is present on all CPUs
  arm64: use shared sysctl constants
  arm64: Drop do_el0_ia_bp_hardening() & do_sp_pc_abort() declarations
      b19e8c68
    • Linus Torvalds's avatar
      Merge tag 'gpio-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio · 1d40890a
      Linus Torvalds authored 
      Pull GPIO fixes from Linus Walleij:

 - Revert two patches to gpio_do_set_config() and implement the proper
   solution that works, also drop an unecessary call in set_config()

 - Fix up the lockdep class for hierarchical IRQ domains.

 - Remove some bridge code for line directions.

 - Fix a register access bug in the Xilinx driver.

* tag 'gpio-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: sifive: fix static checker warning
  spmi: pmic-arb: Set lockdep class for hierarchical irq domains
  gpio: xilinx: Fix bug where the wrong GPIO register is written to
  gpiolib: remove unnecessary argument from set_config call
  gpio: bd71828: Remove unneeded defines for GPIO_LINE_DIRECTION_IN/OUT
  MAINTAINERS: Sort entries in database for GPIO
  gpiolib: fix gpio_do_set_config()
  Revert "gpiolib: remove set but not used variable 'config'"
  Revert "gpiolib: Remove duplicated function gpio_do_set_config()"
      1d40890a
    • David S. Miller's avatar
      Merge branch 'icmp-account-for-NAT-when-sending-icmps-from-ndo-layer' · 803381f9
      David S. Miller authored 
      Jason A. Donenfeld says:

====================
icmp: account for NAT when sending icmps from ndo layer

The ICMP routines use the source address for two reasons:

1. Rate-limiting ICMP transmissions based on source address, so
   that one source address cannot provoke a flood of replies. If
   the source address is wrong, the rate limiting will be
   incorrectly applied.

2. Choosing the interface and hence new source address of the
   generated ICMP packet. If the original packet source address
   is wrong, ICMP replies will be sent from the wrong source
   address, resulting in either a misdelivery, infoleak, or just
   general network admin confusion.

Most of the time, the icmp_send and icmpv6_send routines can just reach
down into the skb's IP header to determine the saddr. However, if
icmp_send or icmpv6_send is being called from a network device driver --
there are a few in the tree -- then it's possible that by the time
icmp_send or icmpv6_send looks at the packet, the packet's source
address has already been transformed by SNAT or MASQUERADE or some other
transformation that CONNTRACK knows about. In this case, the packet's
source address is most certainly the *wrong* source address to be used
for the purpose of ICMP replies.

Rather, the source address we want to use for ICMP replies is the
original one, from before the transformation occurred.

Fortunately, it's very easy to just ask CONNTRACK if it knows about this
packet, and if so, how to fix it up. The saddr is the only field in the
header we need to fix up, for the purposes of the subsequent processing
in the icmp_send and icmpv6_send functions, so we do the lookup very
early on, so that the rest of the ICMP machinery can progress as usual.

Changes v3->v4:
- Add back the skb_shared checking, since the previous assumption isn't
  actually true [Eric]. This implies dropping the additional patches v3 had
  for removing skb_share_check from various drivers. We can revisit that
  general set of ideas later, but that's probably better suited as a net-next
  patchset rather than this stable one which is geared at fixing bugs. So,
  this implements things in the safe conservative way.

Changes v2->v3:
- Add selftest to ensure this actually does what we want and never regresses.
- Check the size of the skb header before operating on it.
- Use skb_ensure_writable to ensure we can modify the cloned skb [Florian].
- Conditionalize this on IPS_SRC_NAT so we don't do anything unnecessarily
  [Florian].
- It turns out that since we're calling these from the xmit path,
  skb_share_check isn't required, so remove that [Florian]. This simplifes the
  code a bit too. **The supposition here is that skbs passed to ndo_start_xmit
  are _never_ shared. If this is not correct NOW IS THE TIME TO PIPE UP, for
  doom awaits us later.**
- While investigating the shared skb business, several drivers appeared to be
  calling it incorrectly in the xmit path, so this series also removes those
  unnecessary calls, based on the supposition mentioned in the previous point.

Changes v1->v2:
- icmpv6 takes subtly different types than icmpv4, like u32 instead of be32,
  u8 instead of int.
- Since we're technically writing to the skb, we need to make sure it's not
  a shared one [Dave, 2017].
- Restore the original skb data after icmp_send returns. All current users
  are freeing the packet right after, so it doesn't matter, but future users
  might not.
- Remove superfluous route lookup in sunvnet [Dave].
- Use NF_NAT instead of NF_CONNTRACK for condition [Florian].
- Include this cover letter [Dave].
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      803381f9
    • Jason A. Donenfeld's avatar
      xfrm: interface: use icmp_ndo_send helper · 45942ba8
      Jason A. Donenfeld authored 
      Because xfrmi is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: default avatarJason A. Donenfeld <Jason@zx2c4.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      45942ba8
    • Jason A. Donenfeld's avatar
      wireguard: device: use icmp_ndo_send helper · a12d7f3c
      Jason A. Donenfeld authored 
      Because wireguard is calling icmp from network device context, it should
use the ndo helper so that the rate limiting applies correctly.  This
commit adds a small test to the wireguard test suite to ensure that the
new functions continue doing the right thing in the context of
wireguard. It does this by setting up a condition that will definately
evoke an icmp error message from the driver, but along a nat'd path.
Signed-off-by: default avatarJason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a12d7f3c
    • Jason A. Donenfeld's avatar
      sunvnet: use icmp_ndo_send helper · 67c9a7e1
      Jason A. Donenfeld authored 
      Because sunvnet is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly. While we're
at it, doing the additional route lookup before calling icmp_ndo_send is
superfluous, since this is the job of the icmp code in the first place.
Signed-off-by: default avatarJason A. Donenfeld <Jason@zx2c4.com>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      67c9a7e1
    • Jason A. Donenfeld's avatar
      gtp: use icmp_ndo_send helper · e0fce6f9
      Jason A. Donenfeld authored 
      Because gtp is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: default avatarJason A. Donenfeld <Jason@zx2c4.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e0fce6f9
    • Jason A. Donenfeld's avatar
      icmp: introduce helper for nat'd source address in network device context · 0b41713b
      Jason A. Donenfeld authored 
      This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: default avatarJason A. Donenfeld <Jason@zx2c4.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0b41713b
    • Linus Torvalds's avatar
      Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 · 64ae1342
      Linus Torvalds authored 
      Pull crypto fix from Herbert Xu:
 "This fixes a Kconfig anomaly when lib/crypto is enabled without Crypto
  API"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: Kconfig - allow tests to be disabled when manager is disabled
      64ae1342
    • David S. Miller's avatar
      Merge branch 'skip_sw-skip_hw-validation' · 07134cf6
      David S. Miller authored 
      Davide Caratti says:

====================
add missing validation of 'skip_hw/skip_sw'

ensure that all classifiers currently supporting HW offload
validate the 'flags' parameter provided by user:

- patch 1/2 fixes cls_matchall
- patch 2/2 fixes cls_flower
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      07134cf6
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7