The basic issue is that despite have been deprecated and warned about as a
very bad thing in the man pages since its inception there are a few real
users of sys_sysctl.  It was my assumption that because sysctl had been
deprecated for all of 2.6 there would be no user space users by this point,
so I initially gave sys_sysctl a very short deprecation period.

Now that I know there are a few real users the only sane way to proceed
with deprecation is to push the time limit out to a year or two work and
work with distributions that have big testing pools like fedora core to
find these last remaining users.

Which means that the sys_sysctl interface needs to be maintained in the
meantime.

Since I have provided a technical measure that allows us to add new sysctl
entries without reserving more binary numbers I believe that is enough to
fix the sys_sysctl binary interface maintenance problems, because there is
no longer a need to change the binary interface at all.

Since the sys_sysctl implementation needs to stay around for a while and
the worst of the maintenance issues that caused us to occasionally break
the ABI have been addressed I don't see any advantage in continuing with
the removal of sys_sysctl.

So instead of merely increasing the deprecation period this patch removes
the deprecation of sys_sysctl and modifies the kernel to compile the code
in by default.

With committing to maintain sys_sysctl we get all of the advantages of a
fast interface for anything that needs it.  Currently sys_sysctl is about
5x faster than /proc/sys, for the same string data.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

When ACPI && NUMA, pxm_to_node is used and it exists in drivers/acpi/numa.c

Tony said:

  The patch makes sense ...  if you pick both of "ACPI" and "NUMA", then you
  need (and should automatically be given) ACPI_NUMA too.

  The only open question is whether there is a better way of getting there.
  Perhaps with less configuration options in the first place?  We are heading
  towards a future where so many systems will be NUMA that there would seem to
  be little benefit in keeping ACPI_NUMA separate from ACPI ...  but perhaps
  we aren't quite there yet.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

There are two bugs in the kretprobe-booster.

1) It doesn't make room for gs registers.

2) It doesn't change status of the current kprobe.  This status will
   effect the fault handling.

This patch fixes these bugs and, additionally, saves skipped registers for
compatibility with the original kretprobe.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If there's a swap file on a software RAID, it should be possible to use this
file for saving the swsusp's suspend image.  Also, this file should be
available to the memory management subsystem when memory is being freed before
the suspend image is created.

For the above reasons it seems that md_threads should not be frozen during the
suspend and the appended patch makes this happen, but then there is the
question if they don't cause any data to be written to disks after the suspend
image has been created, provided that all filesystems are frozen at that time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

I forgot to has the size-in-blocks to (loff_t) before shifting up to a
size-in-bytes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It turns out that CHANGE is preferred to ONLINE/OFFLINE for various reasons
(not least of which being that udev understands it already).

So remove the recently added KOBJ_OFFLINE (no-one is likely to care anyway)
and change the ONLINE to a CHANGE event

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The Coverity checker noted that in
drivers/telephony/ixj.c:ixj_build_filter_cadence(), filter_en[4] or
filter_en[5] could be written to.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

All device-mapper targets must complete outstanding I/O before suspending.
The mirror target generates I/O in its recovery phase and fails to wait for
it.  It needs to be tracked so we can ensure that it has completed before we
suspend.

[akpm@osdl.org: cleanup]
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

When adding paths to the round-robin path selector, their order gets inverted,
which is not desirable.

Fix by replacing list_add() with list_add_tail().
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If the device is already suspended, just return the error and skip the code
that would incorrectly wipe md->suspended_bdev.

(This isn't currently a problem because existing code avoids calling this
function if the device is already suspended.)
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

There is a race between dev_create() and find_device().

If the mdptr has not yet been stored against a device, find_device() needs to
behave as though no device was found.  It already returns NULL, but there is a
dm_put() missing: it must drop the reference dm_get_md() took.

The bug was introduced by dm-fix-mapped-device-ref-counting.patch.

It manifests itself if another dm ioctl attempts to reference a newly-created
device while the device creation ioctl is still running.  The consequence is
that the device cannot be removed until the machine is rebooted.  Certain udev
configurations can lead to this happening.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

o Currently there is no specific alignment restriction in linker script
  and in some cases it can be placed non 4K aligned addresses. This fails
  kexec which checks that segment to be loaded is page aligned.

o I guess, it does not harm data segment to be 4K aligned.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In the case where an open creates the file, we shouldn't be rechecking
permissions to open the file; the open succeeds regardless of what the new
file's mode bits say.

This patch fixes the problem, but only by introducing yet another parameter
to nfsd_create_v3.  This is ugly.  This will be fixed by later patches.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Neil Brown <neilb@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Minor rearrangement, cleanup of do_open_lookup().  No change in behavior.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Neil Brown <neilb@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

set_mb() is used by set_current_state() which needs mb(), not wmb().  I
think it would be right to assume that set_mb() implies mb(), all arches
seem to do just this.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If the microcode driver is built in (rather than module) there are some,
ehm, interesting effects happening due to the new "call out to userspace"
behavior that is introduced..  and which runs too early.  The result is a
boot hang; which is really nasty.

The patch below is a minimally safe patch to fix this regression for 2.6.19
by just not requesting actual microcode updates during early boot.  (That
is a good idea in general anyway)

The "real" fix is a lot more complex given the entire cpu hotplug scenario
(during cpu hotplug you normally need to load the microcode as well); but
the interactions for that are just really messy at this point; this fix at
least makes it work and avoids a full detangle of hotplug.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* merom:v2.6/linux:
  x86-64: write IO APIC irq routing entries in correct order
  x86-64: clean up io-apic accesses

This is the x86-64 version of f9dadfa7
that did the same thing on i386.

Since the "mask" bit is in the low word, when we write a new entry, we
need to write the high word first, before we potentially unmask it.

The exception is when we actually want to mask the interrupt, in which
case we want to write the low word first to make sure that the high word
doesn't change while the interrupt routing is still active.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This is just commit 130fe05d ported to
x86-64, for all the same reasons.  It cleans up the IO-APIC accesses in
order to then fix the ordering issues.

We move the accessor functions (that were only used by io_apic.c) out of
a header file, and use proper memory-mapped accesses rather than making
up our own "volatile" pointers.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This reverts commit de09bddb.  It tried
to reserve the MMCONFIG mmio memory ranges, but since the MMCONFIG
information is broken and often bogus (which is why we don't dare use it
most of the time _anyway_), it does more harm than good.

Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] sata_via: fix obvious typo

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [DECNET]: Endianess fixes (try #2)
  [TG3]: Fix array overrun in tg3_read_partno().
  [NET]: Set truesize in pskb_copy
  [NETPOLL]: Compute checksum properly in netpoll_send_udp().
  [PKT_SCHED] sch_htb: Use hlist_del_init().
  [TCP]: Don't use highmem in tcp hash size calculation.
  [NET]: kconfig, correct traffic shaper

Spotted by Martin Devera.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Ok, things are clearly starting to calm down.. Finally.

* 'fixes_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbglaw/vax-linux:
  Update for the srm_env driver.

Here are some fixes to endianess problems spotted by Al Viro.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proper upper limits for the loops and check for all error
conditions.

The problem was noticed by Adrian Bunk.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since pskb_copy tacks on the non-linear bits from the original
skb, it needs to count them in the truesize field of the new skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise we can hit paths that (legally) do multiple deletes on the
same node and OOPS with the HLIST poison values there instead of
NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes consideration of high memory when determining TCP
hash table sizes.  Taking into account high memory results in tcp_mem
values that are too large.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

As Patrick McHardy <kaber@trash.net> suggested, Traffic Shaper is now
obsolete and alternative to it is no longer CBQ, since its problems with
virtual devices, alter Kconfig text to reflect this -- put a link to the
traffic schedulers as a whole.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3927/1: Allow show_mem() to work with holes in memory map.
  [ARM] 3926/1: make timer led handle HZ != 100
  [ARM] 3923/1: S3C24XX: update s3c2410_defconfig with new drivers
  [ARM] 3922/1: S3C24XX: update s3c2410_defconfig to 2.6.19-rc4
  [ARM] 3921/1: S3C24XX: remove bast_defconfig
  [ARM] 3920/1: S3C24XX: Remove smdk2410_defconfig
  [ARM] 3919/1: Fixed definition of some PXA270 CIF related registers
  [ARM] 3918/1: ixp4xx irq-chip rework
  [ARM] 3912/1: Make PXA270 advertise HWCAP_IWMMXT capability
  [ARM] 3915/1: S3C2412: Add s3c2410_gpio_getirq() to general gpio.c
  [ARM] 3917/1: Fix dmabounce symbol exports

This patch contains a fix for a bug introduced more than a year ago
(not setting *eof) and updates whitespace a bit.
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>

show_mem() was not correctly handling holes in the memory
map.  It was treating the freed sections of the map as
though they contained valid struct page entries.  This
could cause incorrect debugging output or even a kernel
panic.

This patch keeps the struct meminfo around after system
initialization so that show_mem() can use it when
scanning memory.  show_mem() now walks over each bank
of each online node, rather than assuming that each node
contains a single contiguous bank.
Signed-off-by: Ray Lehtiniemi <rayl@mail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The timer LED is unusable at HZ=large, since it's got
a hard-wired value of 100 ticks per cycle; when HZ=1024
(for example) it's essentially always-on.  This patch
just makes that be HZ ticks per cycle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

e1000: Fix suspend/resume powerup and irq allocation

From: Auke Kok <auke-jan.h.kok@intel.com>

After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.

Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Through some experimentation with the similarly built bcm43xx I came to
the conclusion that if the hw/firmware sets a bit in the interrupt
register, an interrupt will only be raised if that bit is included in
the interrupt mask. Hence, the interrupt mask is more like an interrupt
control mask.

This patch changes the comment to reflect that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix EV64120 and Ocelot builds by providing a plat_timer_setup().
  [MIPS] EV64120: Fix PCI interrupt allocation.
  [MIPS] Make irq number allocator generally available for fixing EV64120.
  [MIPS] EV64120: Fix timer initialization for HZ != 100.
  [MIPS] Ocelot 3: Fix MAC address detection after platform_device conversion.
  [MIPS] Ocelot C: Fix MAC address detection after platform_device conversion.
  [MIPS] SB1: On bootup only flush cache on local CPU.
  [MIPS] Ocelot 3: Fix large number of warnings.
  [MIPS] Ocelot C: Fix mapping of ioport address range.
  [MIPS] Ocelot C: Fix warning about missmatching format string.
  [MIPS] Ocelot C: fix eth registration after conversion to platform_device
  [MIPS] Ocelot C: Fix large number of warnings.