Minor sparse warning fix.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix "bnx2->flags" names with BNX2_* for consistency.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts.  We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.

The parallel detect logic is cleaned up slightly to better integrate
the workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct.  It happens that they are the same in this
case because we are using the first MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The chip has problem running in this mode and needs to be disabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-3945.c: In function 'iwl3945_add_radiotap':
drivers/net/wireless/iwlwifi/iwl-3945.c:269: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix rfkill code which caused a use-after-free bug. Thanks to David
Woodhouse for spotting this out.

Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes a warning print from ieee80211_sta_stop_rx_ba_session
in case the tid is inactive when interface goes down.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds a check to insure that Rx A-MPDU will be stopped only
for the proper device.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Before calling update_beacon() mac80211 must
initialize the control.vif pointer so it can
be used by the driver to determine which
interface is trying to send the beacon.

v2: ieee80211_beacon_get() should also initialize the
vif pointer since it can be called by mac80211 internally
before calling config_interface().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: re-pepper debug statementThe recent fluff of updates
didn't put proper lbs_deb_enter/leave calls into the source code.
Add them where appropriate.

Also contains some whitespace changes.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The CF card only has a very old firmware (5.0.16p0). This firmware doesn't
know anything about mesh config. However, current code blindly calls
mesh_config when the card is inserted. So check the firmware version before
issuing this command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Always shows the firmware release.

Also converts the firmware release into something that is easily comparable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

boot2_version is purely USB specific, so move it to struct if_usb_card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

netif_rx should be called only from interrupt context. if_cs and if_sdio receive
packets from other contexts, and thus should call netif_rx_ni.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds lots of N-PHY related lookup tables.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The << and >> operators need space on each side.

Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The external iwlwifi driver comes with a README file that is
referenced by the Kconfig. This README is not present in the
driver included in the kernel. Remove references to this
documentation.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch renames iwl3945_rate_scale_priv to iwl3945_rs_sta as it
better represents the purpose of this variable.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1, This patch renames iwl4965_rate_scale_priv to iwl4965_lq_sta.
   This type represents a station's link quality.
2. The names of the variables of this type were rs_priv, lq_data, lq, crl
   across the file. All are now unified under the name lq_sta.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds iwl_free_fw_desc ucode helper function.
It also moves ucode helper functions to iwl-helpers.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After we delay device initialization until interface up, there are more
conditions for the hardware rf_kill switch states during suspend and
resume. For example, before suspend we can have interface up or down,
rf_kill enable or disable; before resume we can have rf_kill enable or
disable. So there are totally 2^3 = 8 conditions to handle. This patch
addressed this problem and makes sure every condition works correctly.

This patch also merges the device suspend and resume handlers with the
mac_start and mac_stop code since they are basically doing the same
thing.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the firmware loading (read firmware from disk and load
it into the device SRAM) from pci_probe time to the first network
interface open time. There are two reasons for doing this:

1. To support kernel buildin iwlwifi drivers. Because kernel initializes
   network devices subsystem before hard disk and SATA subsystem, it is
   impossible to get the firmware image from hard disk in the PCI probe
   handler. Thus delaying the firmware loading into the network
   interface open time is the way to go. Note, we only read the firmware
   image from hard disk the first time the interface is open. After this
   is succeeded, we cache the firmware image into the host memory. This
   is a performance gain when user open and close the interface multiple
   times and is necessary for device suspend and resume.

2. For better power saving. When the iwlwifi modules are loaded (or
   buildin the kernel) but the wireless network interface is not being
   used, it is a good practice the wireless device consumes as less
   power as possible. Unloading the firmware from the wireless device
   and unregister the driver's interrupt handler in the network
   interface close handler provides users a way to achieve this. User
   space network configuration tools (i.e NetworkManager) can also
   contribute here when it detects a wired cable is connected and
   close the wireless interface automatically.

This patch also includes the pci_save/restore_state() fixed by Ian Schram
upon the first version.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Document scan command.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes iwl4965_tx_cmd function and splits its content to
iwl4965_hw_build_tx_cmd_rate, iwl4965_build_tx_cmd_basic,
and iwl4965_tl_get_stats function. The latest one will be deprecated
when traffic load will move to rate scale module.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch moves iwl4965_get_dma_hi_address function to iwl-headers.h
as iwl_get_dma_hi_address. This function will be used in more chipsets
than only 4965.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This function removes redundant code in iwl4965_tx_cmd
function, leftovers of previous design.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds code and table data for channel switching on NPHYs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds some code to init the 2055 radio.
This patch adds two files "tables_nphy.h" and "tables_nphy.c"
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add boardflags-high.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add the register definitions for the Broadcom 2055 N-radio.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert optional struct size checks to non-optional compile-time checks.
Furthermore BUILD_BUG_ON() which will be optimized away by the compiler.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for new firmware.
Old firmware is still supported until July 2008.

To get new firmware, go to
ftp://ftp.linksys.com/opensourcecode/wrt150nv11/1.51.3/
and download the tarball. We don't have a smaller tarball, yet.
That will be fixed later.
You can extract firmware out of the "wl_ap.o" file contained
in this tarball using latest fwcutter. You must pass the option
--unsupported to fwcutter.
Fwcutter-010 with official support for a new firmware image will
be released soon.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes reading of the high 16 bits of the radio ID
on new devices. 2055 radios want lo16 to be read first.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For TX rings the queue_idx should start at
IEEE80211_TX_QUEUE_DATA0 and for each followup
ring this index needs to be increased.

For the RX ring the queue_idx should be set
to 0. We don't need to initialize the tx_params.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2500usb and rt73usb data and desc pointer initialization
was incorrect because it was using uninitialized variables
to determine the length.

In addition rt2500usb used skb_pull and removed the ieee80211
from each received frame instead of using skb_trim to remove
the device descriptor from the frame.

Finally this also fixes the descriptor override when 4 byte
aligning occured. We still need a completely valid descriptor
when using the TX/RX dumping capabilities in debugfs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>