This provides a function gpiochip_irqchip_add() to set
up an irqchip for a GPIO controller, and a function
gpiochip_set_chained_irqchip() to chain it to a parent
irqchip.

Most GPIOs are of the type where a number of lines form
a cascaded interrupt controller chained onto
the primary system interrupt controller (or further down the
chain) so let's add this helper and factor the code to
request the lines to be used as IRQs, the .to_irq() function
and the irqdomain into the core as well.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The old platform data struct is just a leftover from the times
when the driver was not probed exclusively from the device tree.
Factor this into the general state container and simplify the
probe path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The "secondary irq" in the nomadik pin control driver is actually
not secondary (as in: can occur any time alongside the ordinary
irq), it is a latent IRQ. It is an IRQ that has occurred when
the system was in sleep state and has been cached in a special
register flagged from the low power management unit (PRCM).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

SYSCON driver was designed for using memory areas (registers)
that are used in several subsystems. There are systems (CPUs)
which use bits in one register for various purposes and thus
should be handled by various kernel subsystems. This driver
allows you to use the individual SYSCON bits as GPIOs.
ARM CLPS711X SYSFLG1 input lines has been added as first user
of this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This switches the COH901 GPIO driver over to using the
.request_resources() and .release_resources() callbacks from
the irqchip vtable and separate the calls from the .enable()
and .disable() callbacks as the latter cannot really say no
to a request, whereas the resource callbacks can.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This switches all GPIO and pin control drivers with irqchips
that were using .startup() and .shutdown() callbacks to lock
GPIO lines for IRQ usage over to using the .request_resources()
and .release_resources() callbacks just introduced into the
irqchip vtable.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix size-cells to show use of OF_GPIO_ACTIVE_LOW flag.
Signed-off-by: Alan Tull <atull@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO operation regions is a new feature introduced in ACPI 5.0
specification. This feature adds a way for platform ASL code to call back
to OS GPIO driver and toggle GPIO pins.

An example ASL code from Lenovo Miix 2 tablet with only relevant part
listed:

 Device (\_SB.GPO0)
 {
     Name (AVBL, Zero)
     Method (_REG, 2, NotSerialized)
     {
         If (LEqual (Arg0, 0x08))
         {
             // Marks the region available
             Store (Arg1, AVBL)
         }
     }

     OperationRegion (GPOP, GeneralPurposeIo, Zero, 0x0C)
     Field (GPOP, ByteAcc, NoLock, Preserve)
     {
         Connection (
             GpioIo (Exclusive, PullDefault, 0, 0, IoRestrictionOutputOnly,
                     "\\_SB.GPO0", 0x00, ResourceConsumer,,)
             {
                 0x003B
             }
         ),
         SHD3,   1,
     }
 }

 Device (SHUB)
 {
     Method (_PS0, 0, Serialized)
     {
         If (LEqual (\_SB.GPO0.AVBL, One))
         {
             Store (One, \_SB.GPO0.SHD3)
             Sleep (0x32)
         }
     }
     Method (_PS3, 0, Serialized)
     {
         If (LEqual (\_SB.GPO0.AVBL, One))
         {
             Store (Zero, \_SB.GPO0.SHD3)
         }
     }
 }

How this works is that whenever _PS0 or _PS3 method is run (typically when
SHUB device is transitioned to D0 or D3 respectively), ASL code checks if
the GPIO operation region is available (\_SB.GPO0.AVBL). If it is we go and
store either 0 or 1 to \_SB.GPO0.SHD3.

Now, when ACPICA notices ACPI GPIO operation region access (the store
above) it will call acpi_gpio_adr_space_handler() that then toggles the
GPIO accordingly using standard gpiolib interfaces.

Implement the support by registering GPIO operation region handlers for all
GPIO devices that have an ACPI handle. First time the GPIO is used by the
ASL code we make sure that the GPIO stays requested until the GPIO chip
driver itself is unloaded. If we find out that the GPIO is already
requested we just toggle it according to the value got from ASL code.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Linux 3.14-rc6

Nothing prevents GPIO drivers from returning values outside the
boolean range, and as it turns out a few drivers are actually doing so.
These values were passed as-is to unsuspecting consumers and created
confusion.

This patch makes the internal _gpiod_get_raw_value() function return a
bool, effectively clamping the GPIO value to the boolean range no
matter what the driver does.

While we are at it, we also change the value parameter of
_gpiod_set_raw_value() to bool type before drivers start doing funny
things with it as well.

Another way to fix this would be to change the prototypes of the driver
interface to use bool directly, but this would require a huge
cross-systems patch so this simpler solution is preferred.

Changes since v1:
- Change local variable type to bool as well, use boolean values in
  code
- Also change prototype of open drain/open source setting functions
  since they are only called from _gpiod_set_raw_value()

This probably calls for a larger booleanization of gpiolib, but let's
keep that for a latter change - right now we need to address the issue
of non-boolean values returned by drivers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The current ACPI GPIO event handling code was never tested against real
hardware with functioning GPIO triggered events (at the time such hardware
wasn't available). Thus it misses certain things like requesting the GPIOs
properly, passing correct flags to the interrupt handler and so on.

This patch reworks ACPI GPIO event handling so that we:

 1) Use struct acpi_gpio_event for all GPIO signaled events.
 2) Switch to use GPIO descriptor API and request GPIOs by calling
    gpiochip_request_own_desc() that we added in a previous patch.
 3) Pass proper flags from ACPI GPIO resource to request_threaded_irq().

Also instead of open-coding the _AEI iteration loop we can use
acpi_walk_resources(). This simplifies the code a bit and fixes memory leak
that was caused by missing kfree() for buffer returned by
acpi_get_event_resources().

Since the remove path now calls gpiochip_free_own_desc() which takes GPIO
spinlock we need to call acpi_gpiochip_remove() outside of that lock
(analogous to acpi_gpiochip_add() path where the lock is released before
those funtions are called).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In order to consolidate _Exx, _Lxx and _EVT to use the same structure make
the structure name to reflect that we are dealing with any event, not just
_EVT.

This is just rename, no functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We are going to add more ACPI specific data to accompany GPIO chip so
instead of allocating it per each use-case we allocate it once when
acpi_gpiochip_add() is called and release it when acpi_gpiochip_remove() is
called.

Doing this allows us to add more ACPI specific data by merely adding new
fields to struct acpi_gpio_chip.

In addition we embed evt_pins member directly to the structure instead of
having it as a pointer. This simplifies the code a bit since we don't need
to check against NULL.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Sometimes it is useful to allow GPIO chips themselves to request GPIOs they
own through gpiolib API. One use case is ACPI ASL code that should be able
to toggle GPIOs through GPIO operation regions.

We can't use gpio_request() because it will pin the module to the kernel
forever (it calls try_module_get()). To solve this we move module refcount
manipulation to gpiod_request() and let __gpiod_request() handle the actual
request. This changes the sequence a bit as now try_module_get() is called
outside of gpio_lock (I think this is safe, try_module_get() handles
serialization it needs already).

Then we provide gpiolib internal functions gpiochip_request/free_own_desc()
that do the same as gpio_request() but don't manipulate module refrence
count. This allows the GPIO chip driver to request and free descriptors it
owns without being pinned to the kernel forever.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

For certain irq types, e.g. gpios, it's necessary to request resources
before starting up the irq.

This might fail so we cannot use the irq_startup() callback because we
might call the irq_set_type() callback before that which does not make
sense when the resource is not available. Calling irq_startup() before
irq_set_type() can lead to spurious interrupts which is not desired
either.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org 
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1403080857160.18573@ionos.tec.linutronix.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

List myself as maintainer for Broadcom's Kona GPIO driver.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The bus and architecture dependencies are already on MFD_CS5535, so
there is no need to repeat them here.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This coding style issue was detected using the checkpatch.pl script
Signed-off-by: Gary Servin <garyservin@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In max732x_probe() driver allocates dummy I2C device (if number of ports
is greater than 8) with i2c_new_dummy() but it does not check the return
value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later
dereferenced by i2c_smbus_read_byte() (called from max732x_readb()).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In max732x_probe() driver allocates dummy I2C device (if number of ports
is greater than 8) however it is not unregistered if probe fails later.
Fix the leak by unregistering dummy I2C device if it was allocated.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds missing #gpio-cells and also adds a
usage example for leds.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The driver missed an of_xlate function to translate gpio numbers
as found in the DT to the correct chip and number.

While there I've set #gpio_cells to a fixed value of 2.

I've used gpio-pxa.c as template for those changes and tested my changes
successfully on a da850 board using entries for gpio-leds in a DT. So I didn't
reinvent the wheel but just copied and tested stuff.

Thanks to Grygorii Strashko for the hint to the existing code in gpio-pxa.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull ARM SoC fixes from from Olof Johansson:
 "A collection of fixes for ARM platforms.  A little large due to us
  missing to do one last week, but there's nothing in particular here
  that is in itself large and scary.

  Mostly a handful of smaller fixes all over the place.  The majority is
  made up of fixes for OMAP, but there are a few for others as well.  In
  particular, there was a decision to rename a binding for the Broadcom
  pinctrl block that we need to go in before the final release since we
  then treat it as ABI"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
  ARM: tegra: add LED options back into tegra_defconfig
  ARM: dts: omap3-igep: fix boot fail due wrong compatible match
  ARM: OMAP3: Fix pinctrl interrupts for core2
  pinctrl: Rename Broadcom Capri pinctrl binding
  pinctrl: refer to updated dt binding string.
  Update dtsi with new pinctrl compatible string
  ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
  ARM: OMAP2+: Add support for thumb mode on DT booted N900
  ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
  ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
  ARM: DRA7: hwmod data: correct the sysc data for spinlock
  ARM: OMAP5: PRM: Fix reboot handling
  ARM: sunxi: dt: Change the touchscreen compatibles
  ARM: sun7i: dt: Fix interrupt trigger types

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

   - Fix another nfs4_sequence corruptor in RELEASE_LOCKOWNER
   - Fix an Oopsable delegation callback race
   - Fix another bad stateid infinite loop
   - Fail the data server I/O is the stateid represents a lost lock
   - Fix an Oopsable sunrpc trace event"

* tag 'nfs-for-3.14-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Fix oops when trace sunrpc_task events in nfs client
  NFSv4: Fail the truncate() if the lock/open stateid is invalid
  NFSv4.1 Fail data server I/O if stateid represents a lost lock
  NFSv4: Fix the return value of nfs4_select_rw_stateid
  NFSv4: nfs4_stateid_is_current should return 'true' for an invalid stateid
  NFS: Fix a delegation callback race
  NFSv4: Fix another nfs4_sequence corruptor

Pull USB fixes from Greg KH:
 "Here are 4 USB fixes for your current tree.

  Two of them are reverts to hopefully resolve the nasty XHCI
  regressions we have been having on some types of devices.  The other
  two are quirks for some Logitech video devices"

* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
  Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
  usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
  usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e

Pull staging driver tree fix from Greg KH:
 "Here is a single staging driver fix for your tree.

  It resolves an issue with arbritary writes to memory if a specific
  driver is loaded"

* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging/cxt1e1/linux.c: Correct arbitrary memory write in c4_ioctl()

This fixes CVE-2014-0102.

The following command sequence produces an oops:

	keyctl new_session
	i=`keyctl newring _ses @s`
	keyctl link @s $i

The problem is that search_nested_keyrings() sees two keyrings that have
matching type and description, so keyring_compare_object() returns true.
s_n_k() then passes the key to the iterator function -
keyring_detect_cycle_iterator() - which *should* check to see whether this is
the keyring of interest, not just one with the same name.

Because assoc_array_find() will return one and only one match, I assumed that
the iterator function would only see an exact match or never be called - but
the iterator isn't only called from assoc_array_find()...

The oops looks something like this:

	kernel BUG at /data/fs/linux-2.6-fscache/security/keys/keyring.c:1003!
	invalid opcode: 0000 [#1] SMP
	...
	RIP: keyring_detect_cycle_iterator+0xe/0x1f
	...
	Call Trace:
	  search_nested_keyrings+0x76/0x2aa
	  __key_link_check_live_key+0x50/0x5f
	  key_link+0x4e/0x85
	  keyctl_keyring_link+0x60/0x81
	  SyS_keyctl+0x65/0xe4
	  tracesys+0xdd/0xe2

The fix is to make keyring_detect_cycle_iterator() check that the key it
has is the key it was actually looking for rather than calling BUG_ON().

A testcase has been included in the keyutils testsuite for this:

	http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=891f3365d07f1996778ade0e3428f01878a1790bReported-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull thermal fixes from Zhang Rui:
 "Specifics:

   - Update the help text of INT3403 Thermal driver, which was not
     friendly to users.  From Zhang Rui.

   - The "type" sysfs attribute of x86_pkg_temp_thermal registered
     thermal zones includes an instance number, which makes the
     thermal-to-hwmon bridge fails to group them all in a single hwmon
     device.  Fixed by Jean Delvare.

   - The hwmon device registered by x86_pkg_temp_thermal driver is
     redundant because the temperature value reported by
     x86_pkg_temp_thermal is already reported by the coretemp driver.
     Fixed by Jean Delvare.

   - Fix a problem that the cooling device can not be updated properly
     if it is initialized at max cooling state.  From Ni Wade.

   - Fix a problem that OF registered thermal zones are running without
     thermal governors.  From Zhang Rui.

   - Commit beeb5a1e ("thermal: rcar-thermal: Enable driver
     compilation with COMPILE_TEST") broke build on archs wihout io
     memory.  Thus make it depend on HAS_IOMEM to bypass build failures.
     Fixed by Richard Weinberger"

* 'for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  Thermal: thermal zone governor fix
  Thermal: Allow first update of cooling device state
  thermal,rcar_thermal: Add dependency on HAS_IOMEM
  x86_pkg_temp_thermal: Fix the thermal zone type
  x86_pkg_temp_thermal: Do not expose as a hwmon device
  Thermal: update INT3404 thermal driver help text

Pull spi fixes from Mark Brown:
 "A scattering of driver specific fixes here.

  The fixes from Axel cover bitrot in apparently unmaintained drivers,
  the at79 bug is fixing a glitch on /CS during initialisation of some
  devices which could break some slaves and the remainder are fixes for
  recently introduced bugs from the past release cycle or so"

* tag 'spi-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacks
  spi: coldfire-qspi: Fix getting correct address for *mcfqspi
  spi: fsl-dspi: Fix getting correct address for master
  spi: spi-ath79: fix initial GPIO CS line setup
  spi: spi-imx: spi_imx_remove: do not disable disabled clocks
  spi-topcliff-pch: Fix probing when DMA mode is used
  spi/topcliff-pch: Fix DMA channel

Pull SCSI target fixes from Nicholas Bellinger:
 "This series addresses a number of outstanding issues wrt to active I/O
  shutdown using iser-target.  This includes:

   - Fix a long standing tpg_state bug where a tpg could be referenced
     during explicit shutdown (v3.1+ stable)
   - Use list_del_init for iscsi_cmd->i_conn_node so list_empty checks
     work as expected (v3.10+ stable)
   - Fix a isert_conn->state related hung task bug + ensure outstanding
     I/O completes during session shutdown.  (v3.10+ stable)
   - Fix isert_conn->post_send_buf_count accounting for RDMA READ/WRITEs
     (v3.10+ stable)
   - Ignore FRWR completions during active I/O shutdown (v3.12+ stable)
   - Fix command leakage for interrupt coalescing during active I/O
     shutdown (v3.13+ stable)

  Also included is another DIF emulation fix from Sagi specific to
  v3.14-rc code"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  Target/sbc: Fix sbc_copy_prot for offset scatters
  iser-target: Fix command leak for tx_desc->comp_llnode_batch
  iser-target: Ignore completions for FRWRs in isert_cq_tx_work
  iser-target: Fix post_send_buf_count for RDMA READ/WRITE
  iscsi/iser-target: Fix isert_conn->state hung shutdown issues
  iscsi/iser-target: Use list_del_init for ->i_conn_node
  iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bug

Revert commit 3130497f ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.

Fixes: 3130497f ("ACPI / sleep: pm_power_off needs more sanity checks to be installed")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'omap-for-v3.14/fixes-dt-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:

Two omap3430 vs 3630 device tree regression fixes for
issues booting 3430 based boards.

* tag 'omap-for-v3.14/fixes-dt-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
  ARM: dts: omap3-igep: fix boot fail due wrong compatible match
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge 'bcm pinctrl rename' From Christin Daudt:

Rename pinctrl dt binding to restore consistency with other bcm mobile
bindings.

* tag 'bcm-for-3.14-pinctrl-reduced-rename' of git://github.com/broadcom/bcm11351:
  pinctrl: Rename Broadcom Capri pinctrl binding
  pinctrl: refer to updated dt binding string.
  Update dtsi with new pinctrl compatible string
  + Linux 3.14-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>

Allwinner fixes from Maxime Ripard:

Two fixes for device trees additions that got added in 3.14. One fixes the
interrupt types of some IPs, the other fixes up a compatible that got
introduced during 3.14

* tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux:
  ARM: sunxi: dt: Change the touchscreen compatibles
  ARM: sun7i: dt: Fix interrupt trigger types
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull cgroup fixes from Tejun Heo:
 "Two cpuset locking fixes from Li.  Both tagged for -stable"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: fix a race condition in __cpuset_node_allowed_softwall()
  cpuset: fix a locking issue in cpuset_migrate_mm()

Pull libata fixes from Tejun Heo:
 "Just a couple patches blacklisting more broken devices"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8 (2BA30001)
  libata: disable queued TRIM for Crucial M500 mSATA SSDs