Some device drivers reset their stats at down/up events, possibly
fooling bonding stats, since they operate with relative deltas.

It is nearly not possible to fix drivers, since some of them compute the
tx/rx counters based on per rx/tx queue stats, and the queues can be
reconfigured (ethtool -L) between the down/up sequence.

Lets avoid accumulating 'negative' values that render bonding stats
useless.

It is better to lose small deltas, assuming the bonding stats are
fetched at a reasonable frequency.

Fixes: 5f0c5f73 ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than assign the positive errno values to ret and then
checking if it is positive and flip the sign, just return the
errno value.

Detected by CoverityScan, CID#986649 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).

That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

ATM dwmac-rk will always set and enable it's internal delay lines.
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.

Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.

Tested only with a RK3288 based board.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit aff3d9ef ("net: stmmac: enable multiple buffers") breaks
numerous boards. while some patch exists for fixing some of it,
dwmac-sunxi is still broken with it.
Since this patch is very huge, it will be better to split it in smaller
part.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-03-29

This series contains updates to i40e and i40evf only.

Preethi changes the default driver mode of operation to descriptor
write-back for VF.

Alex cleans up and addresses several issues in the way that i40e handles
private flags.  Modifies the driver to use the length of the packet
instead of the DD status bit to determine if a new descriptor is ready
to be processed.  Refactors the driver by pulling the code responsible
for fetching the receive buffer and synchronizing DMA into a single
function.  Also pulled the code responsible for handling buffer
recycling and page counting and distributed it through several functions,
so we can commonize the bits that handle either freeing or recycling the
buffers.  Cleans up the code in preparation for us adding support for
build_skb().  Changed the way we handle the maximum frame size for the
receive path so it is more consistent with other drivers.

Paul enables XL722 to use the direct read/write method since it does not
support the AQ command to read/write the control register.

Christopher fixes a case where we miss an arq element if a new one is
added before we enable interrupts and exit the loop.

Jake cleans up a pointless goto statement.  Also cleaned up a flag that
was not being used.

Carolyn does round 2 for adding a delay to the receive queue to
accommodate the hardware needs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Parthasarathy Bhuvaragan says:

====================
tipc: add socketpair support

We add socketpair support for connection oriented sockets in
the first patch and for connection less in the second.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

for socketpairs using connectionless transport, we cache
the respective node local TIPC portid to use in subsequent
calls to send() in the socket's private data.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sockets A and B are connected back-to-back, similar to what
AF_UNIX does.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I found a bug by:

0. boot and start dhcp client
1. echo mem > /sys/power/state
2. resume back immediately
3. don't touch dhcp client to renew the lease
4. ping the gateway. No acks

Usually, after step2, the DHCP lease isn't expired, so in theory we
should resume all back. But in fact, it doesn't. It turns out
the rx mode isn't resumed correctly. This patch fixes it by adding
mvneta_set_rx_mode(dev) in the resume hook if interface is running.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

RGMII_RXID and RGMII_TX_ID share the same GMAC CTRL setting as RGMII
or RGMII_ID.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx5e-pedit 2017-03-28

This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.

The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.

One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.

Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.

The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.

The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.

Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.

Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.

I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit skips nexthops in a route if the device has been
deleted. Update lfib_nlmsg_size accordingly.
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:

- descend into drivers/net/phy/ unconditionally

- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
  which allows us not to expose the internal MDIO board info list and
  mutex, yet maintain the logic within the same file

- relocate the code that creates a MDIO device into
  drivers/net/phy/mdio_bus.c

- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
  defined (y or m)

Fixes: 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea013 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a delay to Rx queue disables to accommodate HW needs.

v2: Added missing check for disable only, additional details on the
need for the ugly delay and fixed spacing on comment.

Change-ID: I2864ca667ce5dcc2cc44f8718113b719742a46a1
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the way we handle the maximum frame size for the Rx
path.  Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount.  With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size.  This makes the behavior more
consistent with the other drivers such as igb which had similar logic.  In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.

Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode.  The legacy Rx mode is what we currently do when performing
Rx.  As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.

Change-ID: I0342998849bbb31351cce05f6e182c99174e7751
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to clean up the code in preparation for us adding
support for build_skb.  Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.

Specifically with this change we split out the code for adding a page to an
exiting skb.

Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions.  This allows us
to commonize the bits that handle either freeing or recycling the buffers.

As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer.  It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.

Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.

The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer.  We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.

Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.

Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This flag hasn't been used since commit 1e1be8f6 ("i40e: ATR policy
change to flush the table to clean stale ATR rules").

Lets simplify things and just remove it.

Change-ID: I76279d84db8a2fd96f445b96aa413059f9256879
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The goto found here for when in MFP mode is pointless. It jumps to the
end of a series of if blocks. However, right after this statement is
a closing '}' for this if block, which will result in the program flow
going to the exact same location as the goto statement indicates. Thus,
regardless of whether we are in MFP mode, the program flow will resume
from the same location.

This arose due to various refactoring which did not notice that this
goto became essentially a no-op.

To properly understand this diff you will need to view a larger context
than is given by default.

Change-ID: I088f73c3831aa5c4e2281380c7a3ce605594300c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a case where we miss an arq element if a new one is added before we
enable interrupts and exit the arq subtask loop. This occurs frequently
with RDMA running on Windows VF and causes long delays that prevent SMB
from establishing connections.

Change-ID: I3e1c8b2b960c12857d9b8275bea2c1563674392e
Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The XL722 doesn't support the AQ command to read/write the control
register so enable it to bypass the check and use the direct read/write
method.

Change-ID: Iefecc737b57207485c90845af5989d5af518bf16
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up and addresses several issues in the way that i40e
handles private flags. Previously the code was choosing fixed bits and
trying to match them up with strings in a somewhat haphazard way. This
resulted in the possibility for adding a new bit and causing a mismatch as
the private flags are linear bits starting at 0, and the private flags in
the driver were split up over a group specific to the PF and a group that
was global.

What this change does is define an array of structs used to represent the
private flags. Contained within the structs are the bits necessary to know
which flags to set and/or clear depending on the state of the bit. By
doing this we can add new bits in the future with minimal overhead and
avoid creating possible mis-matches should we need to remove a flag based
on compile options.

Change-ID: Ia3214ab04f0ab2f70354ac0997a135f1d01b0acd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The current driver mode is to use a write-back mechanism for the head
register which indicates transmit completions. The VF driver needs to be
able to work on hardware that exclusively uses descriptor write-back, so
change the default driver mode of operation to descriptor write-back for
VF. In our analysis, performance wasn't significantly different with
either write-back method.

Change-ID: Ia92e4ec77c2df8dc4515c71d53746d57d77759af
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Andrew Lunn says:

====================
break include loop and dsa devlink support

These two patches add very basic support for devlink to DSA, in
preparation for playing with dpipe.

The first patch is needed to break an include loop between
netdevice.h, dsa.h and devlink.h. We need to remove dsa.h from
netdevice.h. As a result, some files fail to compile, because they
require includes pulled in via dsa.h. So this patch adds a number of
includes in various places. The majority is within the network
subsystem, but cifs also needs a few fixes.

0-day has been chewing on this for over a day now, and not found any
breakage. But Arnd's randconfig might uncover something.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Register the switch and its ports with devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.

Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.

No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
netconf: Add support for RTM_DELNETCONF

netconf notifications are sent as devices register but not when they
are deleted leaving userspace caches out of sync. Add support for
RTM_DELNETCONF to ipv4, ipv6 and mpls.

MPLS is missing RTM_NEWNETCONF as devices are created, so add it as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Send netconf notifications for MPLS when the device registers and
unregisters.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor mpls_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet6_netconf_fill_devconf to skip devconf
references if it is NULL.

Allows a userspace cache to remove entries as devices are deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor inet6_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet_netconf_fill_devconf to skip devconf
references if it is NULL.

Allows a userspace cache to remove entries as devices are deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor inet_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor interrupt moderation code for flexibility because parameters are
different for 10G and 25G cards.  Currently parameters (for 10G only) come
from macros compiled-in to the PF and VF drivers; fix it so that parameters
suitable for the card (10G or 25G) come from the NIC firmware via response
to a command.

Also bump up driver version to 1.5.1 to match newer NIC firmware version.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>