Realized I put a / in the filename of this device too.

Here is the fix:

Oops. Realized I had a / in the file name in this patch too.

Please apply to correct it:

--On Friday, April 09, 2004 12:02:19 AM +0200 Marcel Holtmann <marcel@holtmann.org> wrote:
>> +static struct class_simple coda_psdev_class;
>
> I think coda_psdev_class must be a pointer.
>
> Regards
>
> Marcel


Doh! I tested on one system and fixed this there. Then accidentally mailed out the
original. Sorry about that. Here is a patch to fix it:

here is a patch that adds class support to the ISDN CAPI module. Without
it udev won't create the /dev/capi20 device node.

Here is a patch to add class support to psdev.c.

I have verified it compiles and works.

Here is a patch that adds sysfs class support to /drivers/char/dsp56k.c

A patch about the tipar.c char driver has been sent on lkml by Sebastien
Bourdeau. It fixes a divide-by-zero error when we try to read/write data
after setting the timeout to 0.

Here is a patch to add class support to the Stallion Intelligent multiport
serial driver.

Here is a patch to add class support to the Stallion multiport
serial driver.

the following patch (against 2.6.5-rc2) teaches fb to use class_simple.
With this patch udev will automagically create device nodes for each
framebuffer registered. Once all drivers are converted to
framebuffer_{alloc,release} we can switch to our own class.

This is what sysfs dir looks like:

notebook:~# tree /sys/class/graphics/
/sys/class/graphics/
`-- fb0
    `-- dev

Here is a patch to add class support to zftape-init.c:

MODULE_DESCRIPTION(ZFTAPE_VERSION " - "
                   "VFS interface for the Linux floppy tape driver. "
                   "Support for QIC-113 compatible volume table "
                   "and builtin compression (lzrw3 algorithm)");

I have verified it compiles but do not have the hardware to test it.

Here is a patch to hook up the qic02 tape device to have class
support in sysfs. I have verified it compiles. I do not have access to
the hardware to test. Could someone who does please verify?

 From the file:
 * This is a driver for the Wangtek 5150 tape drive with
 * a QIC-02 controller for ISA-PC type computers.
 * Hopefully it will work with other QIC-02 tape drives as well.

This happens when the device associated with a class device goes away before
the class does.

It was being used before initialized, not nice :(

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

We no longer have a CPU_OFFLINE notifier: we freeze the machine and
kill the CPU atomically.  Remove it.

Various files keep per-cpu caches which need to be freed/moved when a
CPU goes down.  All under CONFIG_HOTPLUG_CPU ifdefs.

scsi.c: drain dead cpu's scsi_done_q onto this cpu.

buffer.c: brelse the bh_lrus queue for dead cpu.

timer.c: migrate timers from dead cpu, being careful of lock order vs
	__mod_timer.

radix_tree.c: free dead cpu's radix_tree_preloads

page_alloc.c: empty dead cpu's nr_pagecache_local into nr_pagecache, and
	free pages on cpu's local cache.

slab.c: stop reap_timer for dead cpu, adjust each cache's free limit, and
	free each slab cache's per-cpu block.

swap.c: drain dead cpu's lru_add_pvecs into ours, and empty its committed_space
	counter into global counter.

dev.c: drain device queues from dead cpu into this one.

flow.c: drain dead cpu's flow cache.

Keep track of kswapds: it's OK that they get moved off a node when the
last CPU goes down, but when a CPU comes back, we should try to move
the kswapd back onto its node.

Workqueues need to bring up/destroy the per-cpu thread on cpu up/down.

1) Add a global list of workqueues, and keep the name in the structure
   (to name the newly created thread).

2) Remove BUG_ON in run_workqueue, since thread is dragged off CPU when
   it goes down.

3) Lock out cpu up/down in flush_workqueue, create_workqueue and
   destroy_workqueue.

4) Add notifier to add/destroy workqueue threads, and take over work.

Change ksoftirqd not to assume it's on the CPU: when a cpu goes down,
it will be rudely dragged off.  Since do_softirq() uses
smp_processor_id(), it's easiest to disable preemption, check that the
cpu is still up, then call do_softirq().

If the cpu is actually offline, wait for the notifier, which kills us.

Take over tasklets from dead cpu in the notifier.

Clean up redundant double assignment in CPU_UP callback.

Add hook for RCU to handle jobs on dead cpu.  Requires new
tasklet_kill_immediate for RCU to clean up its tasklet (which might
have been about to run, so tasklet_kill won't work).

Change the migration thread to directly use its cpu arg, rather than
smp_processor_id(): if a cpu goes up then down rapidly, it can be on
the wrong cpu just before it is stopped.

Add code to stop the migration thread on CPU_DEAD and CPU_UP_CANCELED.

Remove the (bogus) priority of the notifier.

We need the migration thread to be RT as soon as the CPU comes online:
for example, stop_machine() (another RT task) expects to yield to it.
Extract the core of setscheduler() and do that when the migration
thread is created.  rq lock is a precaution against the (theoretical)
possibility of someone else doing setscheduer on this thread at the
same time.

Currently the migration thread re-enables irqs, then calls
move_task_away which disables IRQs again and actually does the move.
This means there is a race where the migration thread gets preempted,
and the target CPU can go down.

Hold irqs disabled in migration thread across move_task_away(), which
now doesn't need to save flags (the other caller is the hotplug CPU
code, where irqs are also disabled).

Grab cpu lock around sched_migrate_task() and sys_sched_setaffinity().
This is a noop without CONFIG_HOTPLUG_CPU.

The sched_migrate_task may have a performance penalty on NUMA if lots
of exec rebalancing is happening, however this only applies to
CONFIG_NUMA and CONFIG_HOTPLUG_CPU, which noone does at the moment
anyway.

Also, the scheduler in -mm solves the race another way, so this will
vanish then.

Don't move tasks onto offline cpus in load_balance and wake_task (the
latter is caused by a completion run from stop_machine).

Note that cpu_is_offline() is a noop when CONFIG_HOTPLUG_CPU=n.

Add "online" sysfs attribute to cpus to bring them up and down.

Again, only under CONFIG_HOTPLUG_CPU.

Implement cpu_down(): uses stop_machine to freeze the machine, then
uses (arch-specific) __cpu_disable() and migrate_all_tasks().

Whole thing under CONFIG_HOTPLUG_CPU, so doesn't break archs which
don't define that.

From: Nikita Danilov <Nikita@Namesys.COM>

remove_suid() ignores return value of notify_change()->i_op->setattr().
This mean, that even if file system fails to clear suid bit,
generic_file_aio_write_nolock() proceeds with write, which is unsafe.

Actually, even ext2's ->setattr() can fail, when trying to update ACL, for
example.

Attached patch modifies remove_suid() to return result of ->setattr(), and
updates in-tree callers.

From: Stelian Pop <stelian@popies.net>

This patchlet is just a resync with my tree, it only increments the meye
driver version number and makes some small comment changes as suggested by
Randy Dunlap.

From: Andy Whitcroft <andyw@uk.ibm.com>

Whilst looking at the memory overcommit logic I noticed that the pointer to
the documentation from the *_vm_enough_memory calls is incorrect.  Also
that in one instance the routine does not have the expected pointers.

From: Stelian Pop <stelian@popies.net>

This patch removes the usage of __devinit in the srs methods of the sonypi
driver, because those functions are also called from sonypi_pm_callback().

Patch originally from Randy Dunlap.

From: Grant Grundler <grundler@parisc-linux.org>

This patch adds a comment to "Documentation/SubmittingDrivers" about the
importance of adding a Copyright notice in submitted code.

The parisc-linux port has neglected this in the past and I've been slowly
trying to correct that (along with proper GPL header).

While I make it sound like GPL is the "only" acceptable license, I'll leave
it up to lawyers to determine what other appropriate license could be used
for a new driver.

From: Carl Spalletta <ioanamitu@yahoo.com>

Fix a comment bug.

From: Matt Domsch <Matt_Domsch@dell.com>

Split EDD assembly code from setup.S into edd.S.  This will enable it to be
#included into x86-64 too.