For drivers that use deferred_xmit for PTP frames (such as sja1105),
there is no need to perform matching between PTP frames and their egress
timestamps, since the sending process can be serialized.

In that case, it makes sense to have the pointer to the skb clone that
DSA made directly in the skb->cb. It will be used for pushing the egress
timestamp back in the application socket's error queue.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.

 2) Read SFP eeprom in max 16 byte increments to avoid problems with
    some SFP modules, from Russell King.

 3) Fix UDP socket lookup wrt. VRF, from Tim Beale.

 4) Handle route invalidation properly in s390 qeth driver, from Julian
    Wiedmann.

 5) Memory leak on unload in RDS, from Zhu Yanjun.

 6) sctp_process_init leak, from Neil HOrman.

 7) Fix fib_rules rule insertion semantic change that broke Android,
    from Hangbin Liu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  pktgen: do not sleep with the thread lock held.
  net: mvpp2: Use strscpy to handle stat strings
  net: rds: fix memory leak in rds_ib_flush_mr_pool
  ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
  ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
  Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
  net: aquantia: fix wol configuration not applied sometimes
  ethtool: fix potential userspace buffer overflow
  Fix memory leak in sctp_process_init
  net: rds: fix memory leak when unload rds_rdma
  ipv6: fix the check before getting the cookie in rt6_get_cookie
  ipv4: not do cache for local delivery if bc_forwarding is enabled
  s390/qeth: handle error when updating TX queue count
  s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
  s390/qeth: check dst entry before use
  s390/qeth: handle limited IPv4 broadcast in L3 TX path
  net: fix indirect calls helpers for ptype list hooks.
  net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
  udp: only choose unbound UDP socket for multicast when not in a VRF
  net/tls: replace the sleeping lock around RX resync with a bit lock
  ...

Pull rdma fixes from Jason Gunthorpe:
 "Things are looking pretty quiet here in RDMA, not too many bug fixes
  rolling in right now. The usual driver bug fixes and fixes for a
  couple of regressions introduced in 5.2:

   - Fix a race on bootup with RDMA device renaming and srp. SRP also
     needs to rename its internal sys files

   - Fix a memory leak in hns

   - Don't leak resources in efa on certain error unwinds

   - Don't panic in certain error unwinds in ib_register_device

   - Various small user visible bug fix patches for the hfi and efa
     drivers

   - Fix the 32 bit compilation break"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/efa: Remove MAYEXEC flag check from mmap flow
  mlx5: avoid 64-bit division
  IB/hfi1: Validate page aligned for a given virtual address
  IB/{qib, hfi1, rdmavt}: Correct ibv_devinfo max_mr value
  IB/hfi1: Insure freeze_work work_struct is canceled on shutdown
  IB/rdmavt: Fix alloc_qpn() WARN_ON()
  RDMA/core: Fix panic when port_data isn't initialized
  RDMA/uverbs: Pass udata on uverbs error unwind
  RDMA/core: Clear out the udata before error unwind
  RDMA/hns: Fix PD memory leak for internal allocation
  RDMA/srp: Rename SRP sysfs name after IB device rename trigger

Pull arm64 fixes from Will Deacon:
 "Another round of mostly-benign fixes, the exception being a boot crash
  on SVE2-capable CPUs (although I don't know where you'd find such a
  thing, so maybe it's benign too).

  We're in the process of resolving some big-endian ptrace breakage, so
  I'll probably have some more for you next week.

  Summary:

   - Fix boot crash on platforms with SVE2 due to missing register
     encoding

   - Fix architected timer accessors when CONFIG_OPTIMIZE_INLINING=y

   - Move cpu_logical_map into smp.h for use by upcoming irqchip drivers

   - Trivial typo fix in comment

   - Disable some useless, noisy warnings from GCC 9"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Silence gcc warnings about arch ABI drift
  ARM64: trivial: s/TIF_SECOMP/TIF_SECCOMP/ comment typo fix
  arm64: arch_timer: mark functions as __always_inline
  arm64: smp: Moved cpu_logical_map[] to smp.h
  arm64: cpufeature: Fix missing ZFR0 in __read_sysreg_by_encoding()

Robert Hancock says:

====================
Xilinx axienet driver updates (v5)

This is a series of enhancements and bug fixes in order to get the mainline
version of this driver into a more generally usable state, including on
x86 or ARM platforms. It also converts the driver to use the phylink API
in order to provide support for SFP modules.

Changes since v4:
-Use reverse christmas tree variable order
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert this driver to use the phylink API rather than the legacy PHY
API. This allows for better support for SFP modules connected using a
1000BaseX or SGMII interface.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the axienet driver requires the use of a second devicetree
node, referenced by an axistream-connected attribute on the Ethernet
device node, which contains the resources for the AXI DMA block used by the
device. This setup is problematic for a use case we have where the Ethernet
and DMA cores are behind a PCIe to AXI bridge and the memory resources for
the nodes are injected into the platform devices using the multifunction
device subsystem - it's not easily possible for the driver to obtain the
platform-level resources from the linked device.

In order to simplify that usage model, and simplify the overall use of
this driver in general, allow for all of the resources to be kept on one
node where the resources are retrieved using platform device APIs rather
than device-tree-specific ones. The previous usage setup is still
supported if the axistream-connected attribute is specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

The axienet driver requires the use of an axistream-connected attribute,
but this isn't documented in the devicetree bindings. Document how this
attribute is supposed to be used, including the upcoming change to make
the usage of this attribute optional.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was previously using the parent node of the specified PHY
node as the device node to register the MDIO bus on. Andrew Lunn
pointed out this is wrong as the PHY node is potentially not even
underneath the MDIO bus for the current device instance. Find the MDIO
node explicitly by looking it up by name under the controller's device
node instead.

This could potentially break existing device trees if they don't use
"mdio" as the name for the MDIO bus, but I did not find any with various
searches and Xilinx's examples all use mdio as the name so it seems like
this should be relatively safe.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mdio child node for the MDIO bus is generally required when using
this driver but was not documented other than being shown in the
example. Document it as an optional (but usually required) parameter.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some platforms, such as iMX6 with PCIe devices, crashes or hangs can
occur if the axienet device continues to perform DMA transfers after
parent devices/busses have been shut down. Shut down the axienet
interface during its shutdown callback in order to avoid this.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Failing initialization on a missing MAC address property is excessive.
We can just fall back to using a random MAC instead, which at least
leaves the interface in a functioning state.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.

To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Specify IRQF_SHARED to support shared interrupts. If the interrupt
handler is called and the device is not indicating an interrupt,
just return IRQ_NONE rather than spewing error messages.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

These registers are important for troubleshooting the state of the DMA
cores.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Xilinx DMA blocks each have their own reset register, but they both
reset the entire DMA engine, so only one of them needs to be reset.

Also, when stopping the device, we need to not just command the DMA
blocks to stop, but wait for them to stop, and trigger a device reset
to ensure that they are completely stopped.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO clock divisor register setting was only applied on the initial
startup when the driver was loaded. However, this setting is cleared
when the device is reset, such as would occur when the interface was
taken down and brought up again, and so the MDIO bus would be
non-functional afterwards.

Split up the MDIO bus setup and enable into separate functions and
re-enable the bus after a device reset, to ensure that the MDIO
registers are set properly. This also allows us to remove direct access
to MDIO registers in xilinx_axienet_main.c and centralize them all in
xilinx_axienet_mdio.c.

Also, lock the MDIO bus lock around the device reset process, to avoid
MDIO accesses from occurring while the MDIO is disabled during the reset.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the MDIO is is brought up before the netdev is registered, it
should be torn down after the netdev is removed. Otherwise, PHY accesses
can potentially access freed MDIO bus references and cause a crash.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.

Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver should now build on (at least) X86 and ARM platforms, so add
them as supported platforms for the driver in Kconfig.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO bus for this driver was being named using the result of
of_address_to_resource on a node which may not have any resource on it,
but the return value of that call was not checked so it was using some
random value in the bus name. Change to name the MDIO bus based on the
resource start of the actual Ethernet register block.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was using in_be32 and out_be32 IO accessors which do not
exist on most platforms. Also, the use of big-endian accessors does not
seem correct as this hardware is accessed over an AXI bus which, to the
extent it has an endian-ness, is little-endian. Switch to standard
ioread32/iowrite32 accessors.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was casting skb pointers to u32 and storing them as such in
the DMA buffer descriptor, which is obviously broken on 64-bit. The area
of the buffer descriptor being used is not accessed by the hardware and
has sufficient room for a 32 or 64-bit pointer, so just store the skb
pointer as such.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the Arria10, Agilex, and Stratix10 SoC, there are a few differences from
the Cyclone5 and Arria5:
 - The emac PHY setup bits are in separate registers.
 - The PTP reference clock select mask is different.
 - The register to enable the emac signal from FPGA is different.

Thus, this patch creates a separate function for setting the phy modes on
Arria10/Agilex/Stratix10. The separation is based a new DTS binding:
"altr,socfpga-stmmac-a10-s10".
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the "altr,socfpga-stmmac-a10-s10" binding for Arria10/Agilex/Stratix10
implementation of the stmmac ethernet controller.

On the Arria10, Agilex, and Stratix10 SoCs, there are a few differences from
the Cyclone5 and Arria5:
     - The emac PHY setup bits are in separate registers.
     - The PTP reference clock select mask is different.
     - The register to enable the emac signal from FPGA is different.

Because of these differences, the dwmac-socfpga glue logic driver will
use this new binding to set the appropriate bits for PHY, PTP reference
clock, and signal from FPGA.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: tls: add basic TX offload

This series adds initial TLS offload support to the nfp driver.
Only TX side is added for now.  We need minor adjustments to
the core tls code:
 - expose the per-skb fallback helper;
 - grow the driver context slightly;
 - add a helper to get to the driver state more easily.
We only support TX offload for now, and only if all packets
keep coming in order.  For retransmissions we use the
aforementioned software fallback, and in case there are
local drops we completely give up on given TCP stream.

This will obviously be improved soon, this patch set is the
minimal, functional yet easily reviewable chunk.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Count TX TLS packets: successes, out of order, and dropped due to
missing record info.  Make sure the RX and TX completion statistics
don't share cache lines with TX ones as much as possible.  With TLS
stats they are no longer reasonably aligned.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the functionality to add and delete TLS connections on
the NFP, received from the kernel TLS callbacks.

Make use of the common control message (CCM) infrastructure to propagate
the kernel state to firmware.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepend connection handle to each transmitted TLS packet.

For each connection, the driver tracks the next sequence number
expected. If an out of order packet is observed, the driver calls into
the TLS kernel code to reencrypt that particular skb.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While offloading TLS connections, drivers need to handle the case where
out of order packets need to be transmitted.

Other drivers obtain the entire TLS record for the specific skb to
provide as context to hardware for encryption. However, other designs
may also want to keep the hardware state intact and perform the
out of order encryption entirely on the host.

To achieve this, export the already existing software encryption
fallback path so drivers could access this.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently drivers have to ensure the alignment of their tls state
structure, which leads to unnecessary layers of getters and
encapsulated structures in each driver.

Simplify all this by marking the driver state as aligned (driver_state
members are currently aligned, so no hole is added, besides ALIGN in
TLS_OFFLOAD_CONTEXT_SIZE_RX/TX would reserve this extra space, anyway.)
With that we can add a common accessor to the core.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 bytes of driver state has been enough so far, but for drivers
which have to store 8 byte handle it's no longer practical to
store the state directly in the context.

Drivers generally don't need much extra state on RX side, while
TX side has to be tracking TCP sequence numbers.  Split the
lengths of max driver state size on RX and TX.

The struct tls_offload_context_tx currently stands at 616 bytes and
struct tls_offload_context_rx stands at 368 bytes.  Upcoming work
will consume extra 8 bytes in both for kernel-driven resync.
This means that we can bump TX side to 16 bytes and still fit
into the same number of cache lines but on RX side we would be 8
bytes over.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subsequent patches will add support for more TX metadata fields.
Prepare for this by handling an additional double word - firmware
handle as metadata type 7.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add FW ABI defines and code for basic init of TLS offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse TLV containing a bitmask of supported crypto operations.
The TLV contains a capability bitmask (supported operations)
and enabled bitmask.  Each operation describes the crypto
protocol quite exhaustively (protocol, AEAD, direction).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW may prefer to handle some communication via a mailbox
or the vNIC may simply not have a control queue (VFs).
Add a way of exchanging ccm-compatible messages via a
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse the mailbox TLV.  When control message queue is not available
we can fall back to passing the control messages via the vNIC
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>