The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.

Fix this by initializing the refcount to be coherent with the initial
device status.

Fixes:
8fff755e (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Determine if a fraglist is needed in the tx path, and allocate it if
necessary before setting up the copy and map operations.
Otherwise, undoing the copy and map operations is tricky.

This fixes a use-after-free: if allocating the fraglist failed, the copy
and map operations that had been set up were still executed, writing
over the data area of a freed skb.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multicast dst are not cached. They carry DST_NOCACHE.

As mentioned in commit f8864972 ("ipv4: fix dst race in
sk_dst_get()"), these dst need special care before caching them
into a socket.

Caching them is allowed only if their refcnt was not 0, ie we
must use atomic_inc_not_zero()

Also, we must use READ_ONCE() to fetch sk->sk_rx_dst, as mentioned
in commit d0c294c5 ("tcp: prevent fetching dst twice in early demux
code")

Fixes: 421b3885 ("udp: ipv4: Add udp early demux")
Tested-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Reported-by: Alex Gartrell <agartrell@fb.com>
Cc: Michal Kubeček <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

When vortex_up is failed, the skb buffers allocated by __netdev_alloc_skb
in vortex_open are not released, which may cause resource leaks.
This bug has been submitted before.
This patch modifies the error handling code to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"len" is a signed integer.  We check that len is not negative, so it
goes from zero to INT_MAX.  PAGE_SIZE is unsigned long so the comparison
is type promoted to unsigned long.  ULONG_MAX - 4095 is a higher than
INT_MAX so the condition can never be true.

I don't know if this is harmful but it seems safe to limit "len" to
INT_MAX - 4095.

Fixes: a8c879a7 ('RDS: Info and stats')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we share an action within a filter, the bind refcnt
should increase, therefore we should not call tcf_hash_release().

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

openvswitch modifies the L4 checksum of a packet when modifying
the ip address. When an IP packet is fragmented only the first
fragment contains an L4 header and checksum. Prior to this change
openvswitch would modify all fragments, modifying application data
in non-first fragments, causing checksum failures in the
reassembled packet.
Signed-off-by: Glenn Griffin <ggriffin.kernel@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex reported the following crash when using fq_codel
with htb:

  crash> bt
  PID: 630839  TASK: ffff8823c990d280  CPU: 14  COMMAND: "tc"
   [... snip ...]
   #8 [ffff8820ceec17a0] page_fault at ffffffff8160a8c2
      [exception RIP: htb_qlen_notify+24]
      RIP: ffffffffa0841718  RSP: ffff8820ceec1858  RFLAGS: 00010282
      RAX: 0000000000000000  RBX: 0000000000000000  RCX: ffff88241747b400
      RDX: ffff88241747b408  RSI: 0000000000000000  RDI: ffff8811fb27d000
      RBP: ffff8820ceec1868   R8: ffff88120cdeff24   R9: ffff88120cdeff30
      R10: 0000000000000bd4  R11: ffffffffa0840919  R12: ffffffffa0843340
      R13: 0000000000000000  R14: 0000000000000001  R15: ffff8808dae5c2e8
      ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
   #9 [...] qdisc_tree_decrease_qlen at ffffffff81565375
  #10 [...] fq_codel_dequeue at ffffffffa084e0a0 [sch_fq_codel]
  #11 [...] fq_codel_reset at ffffffffa084e2f8 [sch_fq_codel]
  #12 [...] qdisc_destroy at ffffffff81560d2d
  #13 [...] htb_destroy_class at ffffffffa08408f8 [sch_htb]
  #14 [...] htb_put at ffffffffa084095c [sch_htb]
  #15 [...] tc_ctl_tclass at ffffffff815645a3
  #16 [...] rtnetlink_rcv_msg at ffffffff81552cb0
  [... snip ...]

As Jamal pointed out, there is actually no need to call dequeue
to purge the queued skb's in reset, data structures can be just
reset explicitly. Therefore, we reset everything except config's
and stats, so that we would have a fresh start after device flipping.

Fixes: 4b549a2e ("fq_codel: Fair Queue Codel AQM")
Reported-by: Alex Gartrell <agartrell@fb.com>
Cc: Alex Gartrell <agartrell@fb.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
[xiyou.wangcong@gmail.com: added codel_vars_init() and qdisc_qstats_backlog_dec()]
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When removing a port's netdevice in 'rocker_remove_ports', we should
also free the allocated 'net_device' structure. Do that by calling
'free_netdev' after unregistering it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 4b8ac966 ("rocker: introduce rocker switch driver")
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Must teardown SR-IOV before unregistering netdev in igb driver, from
    Alex Williamson.

 2) Fix ipv6 route unreachable crash in IPVS, from Alex Gartrell.

 3) Default route selection in ipv4 should take the prefix length, table
    ID, and TOS into account, from Julian Anastasov.

 4) sch_plug must have a reset method in order to purge all buffered
    packets when the qdisc is reset, likewise for sch_choke, from WANG
    Cong.

 5) Fix deadlock and races in slave_changelink/br_setport in bridging.
    From Nikolay Aleksandrov.

 6) mlx4 bug fixes (wrong index in port even propagation to VFs,
    overzealous BUG_ON assertion, etc.) from Ido Shamay, Jack
    Morgenstein, and Or Gerlitz.

 7) Turn off klog message about SCTP userspace interface compat that
    makes no sense at all, from Daniel Borkmann.

 8) Fix unbounded restarts of inet frag eviction process, causing NMI
    watchdog soft lockup messages, from Florian Westphal.

 9) Suspend/resume fixes for r8152 from Hayes Wang.

10) Fix busy loop when MSG_WAITALL|MSG_PEEK is used in TCP recv, from
    Sabrina Dubroca.

11) Fix performance regression when removing a lot of routes from the
    ipv4 routing tables, from Alexander Duyck.

12) Fix device leak in AF_PACKET, from Lars Westerhoff.

13) AF_PACKET also has a header length comparison bug due to signedness,
    from Alexander Drozdov.

14) Fix bug in EBPF tail call generation on x86, from Daniel Borkmann.

15) Memory leaks, TSO stats, watchdog timeout and other fixes to
    thunderx driver from Sunil Goutham and Thanneeru Srinivasulu.

16) act_bpf can leak memory when replacing programs, from Daniel
    Borkmann.

17) WOL packet fixes in gianfar driver, from Claudiu Manoil.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits)
  stmmac: fix missing MODULE_LICENSE in stmmac_platform
  gianfar: Enable device wakeup when appropriate
  gianfar: Fix suspend/resume for wol magic packet
  gianfar: Fix warning when CONFIG_PM off
  act_pedit: check binding before calling tcf_hash_release()
  net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket
  net: sched: fix refcount imbalance in actions
  r8152: reset device when tx timeout
  r8152: add pre_reset and post_reset
  qlcnic: Fix corruption while copying
  act_bpf: fix memory leaks when replacing bpf programs
  net: thunderx: Fix for crash while BGX teardown
  net: thunderx: Add PCI driver shutdown routine
  net: thunderx: Fix crash when changing rss with mutliple traffic flows
  net: thunderx: Set watchdog timeout value
  net: thunderx: Wakeup TXQ only if CQE_TX are processed
  net: thunderx: Suppress alloc_pages() failure warnings
  net: thunderx: Fix TSO packet statistic
  net: thunderx: Fix memory leak when changing queue count
  net: thunderx: Fix RQ_DROP miscalculation
  ...

Pull btrfs fixes from Chris Mason:
 "Filipe fixed up a hard to trigger ENOSPC regression from our merge
  window pull, and we have a few other smaller fixes"

* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix quick exhaustion of the system array in the superblock
  btrfs: its btrfs_err() instead of btrfs_error()
  btrfs: Avoid NULL pointer dereference of free_extent_buffer when read_tree_block() fail
  btrfs: Fix lockdep warning of btrfs_run_delayed_iputs()

Pull sound fixes from Takashi Iwai:
 "This became a relative big update as it includes the collected ASoC
  fixes.  There are a few fixes in ASoC core side, mostly for DAPM and
  the new topology API.  The rest are various ASoC driver-specific
  fixes, as well as the usual HD-audio and USB-audio quirks"

* tag 'sound-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits)
  ALSA: hda - Fix MacBook Pro 5,2 quirk
  ALSA: hda - Fix race between PM ops and HDA init/probe
  ALSA: usb-audio: add dB range mapping for some devices
  ALSA: hda - Apply a fixup to Dell Vostro 5480
  ALSA: hda - Add pin quirk for the headset mic jack detection on Dell laptop
  ALSA: hda - Apply fixup for another Toshiba Satellite S50D
  ALSA: fireworks: add support for AudioFire2 quirk
  ALSA: hda - Fix the headset mic that will not work on Dell desktop machine
  ALSA: hda - fix cs4210_spdif_automute()
  ASoC: pcm1681: Fix setting de-emphasis sampling rate selection
  ASoC: ssm4567: Keep TDM_BCLKS in ssm4567_set_dai_fmt
  ASoC: sgtl5000: Fix up define for SGTL5000_SMALL_POP
  ASoC: dapm: Don't add prefix to widget stream name
  ASoC: rt5645: Check if codec is initialized in workqueue handler
  ASoC: Intel: Get correct usage_count value to load firmware
  ASoC: topology: Fix to add dapm mixer info
  ASoC: zx: spdif: Fix devm_ioremap_resource return value check
  ASoC: zx: i2s: Fix devm_ioremap_resource return value check
  ASoC: mediatek: Use platform_of_node for machine drivers
  ASoC: Free card DAPM context on snd_soc_instantiate_card() error path
  ...

Commit 50649ab1 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab1 back.

This fixes the following errors when used as a module:
  stmmac_platform: module license 'unspecified' taints kernel.
  Disabling lock debugging due to kernel taint
  stmmac_platform: Unknown symbol devm_kmalloc (err 0)
  stmmac_platform: Unknown symbol stmmac_suspend (err 0)
  stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
  stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
  stmmac_platform: Unknown symbol platform_get_resource (err 0)
  stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
  stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
  stmmac_platform: Unknown symbol of_alias_get_id (err 0)
  stmmac_platform: Unknown symbol stmmac_resume (err 0)
  stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)

Fixes: 50649ab1 ("stmmac: drop driver from stmmac platform code")
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Claudiu Manoil says:

====================
gianfar: wol magic packet fixes

These changes were already validated as part of FSL SDK.
Patch 2 fixes occasional wake-on magic packet failures during
traffic, probably due to incorrect traffic stop/ device halt
sequence and incorrect usage of txlock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.

The bflock is obviously obsoleted, its utility has been corroded
over time.  The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines.  The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device.  With these changes, the TX processing is stopped before
gfar_halt().

Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume.  Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.

Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)

Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CC      drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
 static void lock_tx_qs(struct gfar_private *priv)
             ^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
 static void unlock_tx_qs(struct gfar_private *priv)
             ^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we share an action within a filter, the bind refcnt
should increase, therefore we should not call tcf_hash_release().

Fixes: 1a29321e ("net_sched: act: Dont increment refcnt on replace")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull IOMMU fixes from Joerg Roedel:
 "These fixes are all for the AMD IOMMU driver:

   - A regression with HSA caused by the conversion of the driver to
     default domains.  The fixes make sure that an HSA device can still
     be attached to an IOMMUv2 domain and that these domains also allow
     non-IOMMUv2 capable devices.

   - Fix iommu=pt mode which did not work because the dma_ops where set
     to nommu_ops, which breaks devices that can only do 32bit DMA.

   - Fix an issue with non-PCI devices not working, because there are no
     dma_ops for them.  This issue was discovered recently as new AMD
     x86 platforms have non-PCI devices too"

* tag 'iommu-fixes-v4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Allow non-ATS devices in IOMMUv2 domains
  iommu/amd: Set global dma_ops if swiotlb is disabled
  iommu/amd: Use swiotlb in passthrough mode
  iommu/amd: Allow non-IOMMUv2 devices in IOMMUv2 domains
  iommu/amd: Use iommu core for passthrough mode
  iommu/amd: Use iommu_attach_group()

Pull drm intel fixes from Daniel Vetter:
 "I delayed my -fixes pull a bit hoping that I could include a fix for
  the dp mst stuff but looks a bit more nasty than that.  So just 3
  other regression fixes, one 4.2 other two cc: stable"

* tag 'drm-intel-fixes-2015-07-31' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Declare the swizzling unknown for L-shaped configurations
  drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt
  drm/i915: Replace WARN inside I915_READ64_2x32 with retry loop

Pull drm fixes from Dave Airlie:
 "This has a bunch of nouveau fixes, as Ben has been hibernating and has
  lots of small fixes for lots of bugs across nouveau.

  Radeon has one major fix for hdmi/dp audio regression that is larger
  than Alex would like, but seems to fix up a fair few bugs, along with
  some misc fixes.

  And a few msm fixes, one of which is also a bit large.

  But nothing in here seems insane or crazy for this stage, just more
  than I'd like"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
  drm/msm/mdp5: release SMB (shared memory blocks) in various cases
  drm/msm: change to uninterruptible wait in atomic commit
  drm/msm: mdp4: Fix drm_framebuffer dereference crash
  drm/msm: fix msm_gem_prime_get_sg_table()
  drm/amdgpu: add new parameter to seperate map and unmap
  drm/amdgpu: hdp_flush is not needed for inside IB
  drm/amdgpu: different emit_ib for gfx and compute
  drm/amdgpu: information leak in amdgpu_info_ioctl()
  drm/amdgpu: clean up init sequence for failures
  drm/radeon/combios: add some validation of lvds values
  drm/radeon: rework audio modeset to handle non-audio hdmi features
  drm/radeon: rework audio detect (v4)
  drm/amdgpu: Drop drm/ prefix for including drm.h in amdgpu_drm.h
  drm/radeon: Drop drm/ prefix for including drm.h in radeon_drm.h
  drm/nouveau/nouveau/ttm: fix tiled system memory with Maxwell
  drm/nouveau/kms/nv50-: guard against enabling cursor on disabled heads
  drm/nouveau/fbcon/g80: reduce PUSH_SPACE alloc, fire ring on accel init
  drm/nouveau/fbcon/gf100-: reduce RING_SPACE allocation
  drm/nouveau/fbcon/nv11-: correctly account for ring space usage
  drm/nouveau/bios: add proper support for opcode 0x59
  ...

With the grouping of multi-function devices a non-ATS
capable device might also end up in the same domain as an
IOMMUv2 capable device.
So handle this situation gracefully and don't consider it a
bug anymore.
Tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Pull xfs fixes from Dave Chinner:
 "There are a couple of recently found, long standing remote attribute
  corruption fixes caused by log recovery getting confused after a
  crash, and the new DAX code in XFS (merged in 4.2-rc1) needs to
  actually use the DAX fault path on read faults.

  Summary:

   - remote attribute log recovery corruption fixes

   - DAX page faults need to use direct mappings, not a page cache
     mapping"

* tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
  xfs: remote attributes need to be considered data
  xfs: remote attribute headers contain an invalid LSN
  xfs: call dax_fault on read page faults for DAX

The newsk returned by sk_clone_lock should hold a get_net()
reference if, and only if, the parent is not a kernel socket
(making this similar to sk_alloc()).

E.g,. for the SYN_RECV path, tcp_v4_syn_recv_sock->..inet_csk_clone_lock
sets up the syn_recv newsk from sk_clone_lock. When the parent (listen)
socket is a kernel socket (defined in sk_alloc() as having
sk_net_refcnt == 0), then the newsk should also have a 0 sk_net_refcnt
and should not hold a get_net() reference.

Fixes: 26abe143 ("net: Modify sk_alloc to not reference count the
      netns of kernel sockets.")
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 55334a5d ("net_sched: act: refuse to remove bound action
outside"), we end up with a wrong reference count for a tc action.

Test case 1:

  FOO="1,6 0 0 4294967295,"
  BAR="1,6 0 0 4294967294,"
  tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 \
     action bpf bytecode "$FOO"
  tc actions show action bpf
    action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
    index 1 ref 1 bind 1
  tc actions replace action bpf bytecode "$BAR" index 1
  tc actions show action bpf
    action order 0: bpf bytecode '1,6 0 0 4294967294' default-action pipe
    index 1 ref 2 bind 1
  tc actions replace action bpf bytecode "$FOO" index 1
  tc actions show action bpf
    action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
    index 1 ref 3 bind 1

Test case 2:

  FOO="1,6 0 0 4294967295,"
  tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok
  tc actions show action gact
    action order 0: gact action pass
    random type none pass val 0
     index 1 ref 1 bind 1
  tc actions add action drop index 1
    RTNETLINK answers: File exists [...]
  tc actions show action gact
    action order 0: gact action pass
     random type none pass val 0
     index 1 ref 2 bind 1
  tc actions add action drop index 1
    RTNETLINK answers: File exists [...]
  tc actions show action gact
    action order 0: gact action pass
     random type none pass val 0
     index 1 ref 3 bind 1

What happens is that in tcf_hash_check(), we check tcf_common for a given
index and increase tcfc_refcnt and conditionally tcfc_bindcnt when we've
found an existing action. Now there are the following cases:

  1) We do a late binding of an action. In that case, we leave the
     tcfc_refcnt/tcfc_bindcnt increased and are done with the ->init()
     handler. This is correctly handeled.

  2) We replace the given action, or we try to add one without replacing
     and find out that the action at a specific index already exists
     (thus, we go out with error in that case).

In case of 2), we have to undo the reference count increase from
tcf_hash_check() in the tcf_hash_check() function. Currently, we fail to
do so because of the 'tcfc_bindcnt > 0' check which bails out early with
an -EPERM error.

Now, while commit 55334a5d prevents 'tc actions del action ...' on an
already classifier-bound action to drop the reference count (which could
then become negative, wrap around etc), this restriction only accounts for
invocations outside a specific action's ->init() handler.

One possible solution would be to add a flag thus we possibly trigger
the -EPERM ony in situations where it is indeed relevant.

After the patch, above test cases have correct reference count again.

Fixes: 55334a5d ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: device reset

v3:
For patch #2, remove cancel_delayed_work().

v2:
For patch #1, remove usb_autopm_get_interface(), usb_autopm_put_interface(), and
the checking of intf->condition.

For patch #2, replace the original method with usb_queue_reset_device() to reset
the device.

v1:
Although the driver works normally, we find the device may get all 0xff data when
transmitting packets on certain platforms. It would break the device and no packet
could be transmitted. The reset is necessary to recover the hw for this situation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this
seems not working correctly, a fix for pin NID 0x15 is needed in
addition.  It's equivalent with the fixup for MacBook Air 1,1, so use
this instead.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131Reported-and-tested-by: Jeffery Miller <jefferym@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull input fixes from Dmitry Torokhov:
 "The main change is support for keyboards and touchpads found in 2015
  editions of Macbooks"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: zforce - don't overwrite the stack"
  Input: bcm5974 - add support for the 2015 Macbook Pro
  HID: apple: Add support for the 2015 Macbook Pro
  Input: bcm5974 - prepare for a new trackpad generation
  Input: synaptics - dump ext10 capabilities as well

Merge tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Two patches headed for -stable.

  nct7802: Fix integer overflow seen when writing voltage limits
  nct7904: Rename pwm attributes to match hwmon ABI"

* tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (nct7802) Fix integer overflow seen when writing voltage limits
  hwmon: (nct7904) Rename pwm attributes to match hwmon ABI

The old style of memory interleaving swizzled upto the end of the
first even bank of memory, and then used the remainder as unswizzled on
the unpaired bank - i.e. swizzling is not constant for all memory. This
causes problems when we try to migrate memory and so the kernel prevents
migration at all when we detect L-shaped inconsistent swizzling.
However, this issue also extends to userspace who try to manually detile
into memory as the swizzling for an individual page is unknown (it
depends on its physical address only known to the kernel), userspace
cannot correctly swizzle.

Note that this is a new attempt for the previously merged one,
reverted in

commit d82c0ba6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Jul 14 12:29:27 2015 +0200

    Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"

This is cc: stable since we need it to fix up troubles with wc cpu
mmaps that userspace recently started to use widely.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91105Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[danvet: Add note about previous (failed attempt).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If the device does not support the aliasing ppgtt, we must translate
user bind requests (PIN_USER) from LOCAL_BIND to a GLOBAL_BIND. However,
since this is device specific we cannot do this conveniently in the
upper layers and so must manage the vma->bound flags in the backend.

Partial revert of commit 75d04a37 [4.2-rc1]
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Tue Apr 28 17:56:17 2015 +0300

    drm/i915/gtt: Allocate va range only if vma is not bound

Note this was spotted by Daniel originally, but we dropped the ball in
getting the fix in before the bug going wild. Sorry all.

Reported-by: Vincent Legoll vincent.legoll@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91133
References: https://bugs.freedesktop.org/show_bug.cgi?id=90224Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Some AMD systems also have non-PCI devices which can do DMA.
Those can't be handled by the AMD IOMMU, as the hardware can
only handle PCI. These devices would end up with no dma_ops,
as neither the per-device nor the global dma_ops will get
set. SWIOTLB provides global dma_ops when it is active, so
make sure there are global dma_ops too when swiotlb is
disabled.
Signed-off-by: Joerg Roedel <jroedel@suse.de>

In passthrough mode (iommu=pt) all devices are identity
mapped. If a device does not support 64bit DMA it might
still need remapping. Make sure swiotlb is initialized to
provide this remapping.
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Since devices with IOMMUv2 functionality might be in the
same group as devices without it, allow those devices in
IOMMUv2 domains too.
Otherwise attaching the group with the IOMMUv2 device to the
domain will fail.
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Remove the AMD IOMMU driver implementation for passthrough
mode and rely on the new iommu core features for that.
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Since the conversion to default domains the
iommu_attach_device function only works for devices with
their own group. But this isn't always true for current
IOMMUv2 capable devices, so use iommu_attach_group instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Use proper typecasting while performing byte-by-byte copy
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently trigger multiple memory leaks when replacing bpf
actions, besides others:

  comm "tc", pid 1909, jiffies 4294851310 (age 1602.796s)
  hex dump (first 32 bytes):
    01 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00  ................
    18 b0 98 6d 00 88 ff ff 00 00 00 00 00 00 00 00  ...m............
  backtrace:
    [<ffffffff817e623e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff8120a22d>] __vmalloc_node_range+0x1bd/0x2c0
    [<ffffffff8120a37a>] __vmalloc+0x4a/0x50
    [<ffffffff811a8d0a>] bpf_prog_alloc+0x3a/0xa0
    [<ffffffff816c0684>] bpf_prog_create+0x44/0xa0
    [<ffffffffa09ba4eb>] tcf_bpf_init+0x28b/0x3c0 [act_bpf]
    [<ffffffff816d7001>] tcf_action_init_1+0x191/0x1b0
    [<ffffffff816d70a2>] tcf_action_init+0x82/0xf0
    [<ffffffff816d4d12>] tcf_exts_validate+0xb2/0xc0
    [<ffffffffa09b5838>] cls_bpf_modify_existing+0x98/0x340 [cls_bpf]
    [<ffffffffa09b5cd6>] cls_bpf_change+0x1a6/0x274 [cls_bpf]
    [<ffffffff816d56e5>] tc_ctl_tfilter+0x335/0x910
    [<ffffffff816b9145>] rtnetlink_rcv_msg+0x95/0x240
    [<ffffffff816df34f>] netlink_rcv_skb+0xaf/0xc0
    [<ffffffff816b909e>] rtnetlink_rcv+0x2e/0x40
    [<ffffffff816deaaf>] netlink_unicast+0xef/0x1b0

Issue is that the old content from tcf_bpf is allocated and needs
to be released when we replace it. We seem to do that since the
beginning of act_bpf on the filter and insns, later on the name as
well.

Example test case, after patch:

  # FOO="1,6 0 0 4294967295,"
  # BAR="1,6 0 0 4294967294,"
  # tc actions add action bpf bytecode "$FOO" index 2
  # tc actions show action bpf
   action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
   index 2 ref 1 bind 0
  # tc actions replace action bpf bytecode "$BAR" index 2
  # tc actions show action bpf
   action order 0: bpf bytecode '1,6 0 0 4294967294' default-action pipe
   index 2 ref 1 bind 0
  # tc actions replace action bpf bytecode "$FOO" index 2
  # tc actions show action bpf
   action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
   index 2 ref 1 bind 0
  # tc actions del action bpf index 2
  [...]
  # echo "scan" > /sys/kernel/debug/kmemleak
  # cat /sys/kernel/debug/kmemleak | grep "comm \"tc\"" | wc -l
  0

Fixes: d23b8ad8 ("tc: add BPF based action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>