The ALC260 model=acer needs GPIO1 setup.  It could be selected well
if the codec SSID is set properly by BIOS, but to make sure, enable it
forcibly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The model=will for ALC260 requires the pin 0x0f to be a headphone and
some special verbs for the COEF to turn on the amp.  Now added these as
fixup entries and removed the static model quirk.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add the jack-detect suppression for an ASUS machine with ALC892 codec.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42655Signed-off-by: Takashi Iwai <tiwai@suse.de>

A few machines with ALC861 & co are reported not to work properly with
the auto-mute feature in software.  The auto-mute feature is implemented
in the hardware level, and the jack-detection never works with them.

Also, rename the fixup index as ALC861_FIXUP_* to follow the standard.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a new flag to indicate that the codec has no jack-detection cap.
This flag should be set for hardwares that have no jack-detect
implementation although the codec chip itself supports it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It's a bit too big and used too often as an inline function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Necessary for working on the jack-detection suppression feature.

The new HP laptops turns off the mute LED with VREF50 or VREF80, but
not in HIZ unlike the previous models.  Since VREF50 (also 80) works
with the previous models, let's use VREF50 for all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A few small WM8994 updates to go on top of the previous lot of things
that were sent.  They collide with some -next work so I'd really like to
get them into 3.3-rc3 if possible to merge back up into the -next code.
All driver specific and unexciting in the grand scheme of things.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The VMID ramp rate is supposed to be 0x3, not 11b. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The driver accidentally exchanged the left/right fields for stereo AC'97
mixer registers.  This affected only the aux and CD inputs because the
line input bypasses the AC'97 codec and the mic input is mono; cards
without AC'97 (Xonar DS/DG/HDAV Slim, HG2PCI, HiFier) were not affected.
Reported-and-tested-by: Abby Cedar <abbycedar@yahoo.com.au>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.31+ <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch adds the HD Audio DeviceIDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This hardware requires same fixup for the node 0x0f like Asus A6Rp.
More information: https://bugzilla.redhat.com/show_bug.cgi?id=785417Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In patch_ca0132.c, the error returned from chipio_write() isn't checked
always.  Also, the power-up/down sequence isn't tracked properly in some
error paths.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The only particularly remarkable change here is the one for handling of
the Android suspend ignore code for idle_bias_off CODECs.  That one is
actually a regression fix as some of the new power savings that have
been introduced confused the suspend ignore code, making devices that
are active for non-audio reasons look like they are idle causing them to
be suspended instead of being kept active.

Wrongly slipped in from the commit 9322ca54.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We can enable VMID independently of the bias in some use cases so we need
to ensure that the core device is powered up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

sparse complains that "spec->multiout.dac_nids" is a pointer.

sound/pci/hda/patch_realtek.c:2321:37: error: incompatible types for operation (>)
sound/pci/hda/patch_realtek.c:2321:37:    left side has type unsigned short const [usertype] *dac_nids
sound/pci/hda/patch_realtek.c:2321:37:    right side has type int

It was meant to be num_dacs instead of dac_nids.
Although the current code still works as expected (when num_dacs is zero,
dac_nids should be NULL, too), better to fix now, of course.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The header 'linux/moduleparam.h' is included twice in
'sound/isa/sb/emu8000_patch.c'. Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In most cases, the slave strings for vmaster are identical between
volumes and switches except for "xxx Volume" and "xxx Switch" suffix.
Now snd_hda_add_vmaster() takes the optional suffix argument so that
each string can be composed with the given suffix, and we can share the
slave name strings in both volume and switch calls nicely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The changes for slave controls in patch_realtek.c must be merged for the
further works.

The recent changes in Realtek auto-parser added the new "Bass Speaker"
and "CLFE" mixer elements which should be tracked as vmaster slaves,
too.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42720Signed-off-by: Takashi Iwai <tiwai@suse.de>

The Lenovo laptops with cx5066 chips seem to work better with
model=auto.  Let's get rid of the fallback to the wrong model.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=738397Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since the dynamic pin power-control and the analog low-current mode
may lead to pop-noise, it's safer to set it off as default.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=741128

Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This is an attempt to fix S3-resume problems reported for a few
laptops with different Conexant codecs.  They show the communication
stalls at some time in S3, and the driver falls back into the
single-cmd mode.  This leads to the silent output or the lack of
auto-mute feature.

As a workaround, here enables the sync_write and the bus-reset flags
to make the communication more stable.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740115
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=738397Signed-off-by: Takashi Iwai <tiwai@suse.de>

VIA codecs have several different power-saving features, and one of
them is the analog low-current mode.  But it turned out that the ALC
mode causes pop-noises at each on/off time on some machines.  As a
quick workaround, disable the ALC when another power-saving feature,
the dynamic pin power-control, is turned off, too, since the dynamic
power-control is already exposed as a mixer enum element so that user
can turn it on/off freely.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=741128

Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The analog low-current mode must be enabled when the no stream is
running but the current detection checks it in a wrong way.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=741128

Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Instead of always writing AC_VERB_SET_POWER_STATE, check the current
power-state and don't write again if the value is already set.
This may reduce the click noise upon the dynamic power-state change
(e.g. in analog-input mixer).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

This typo caused the wrong codec's nid to be checked for wcaps type.
As a result, sometimes speakers would duplicate the output sent to
HDMI output.

Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/924320Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

For master mode, set Output [X|A|V]SP_SCLK Sourcing Mode to MCLK Mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Susan Gao <sgao@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

If cs_automic is called twice (like it is during init) while the mic
is present, it will over-write the last_input with the new one,
causing it to switch back to the automic input when the mic is
unplugged. This leaves the driver in a state (cur_input, last_input,
and automix_idx the same) where the internal mic can not be selected
until it is rebooted without the mic attached.

Check that the mic hasn't already been switched to before setting
last_input.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If an idle_bias_off device is in any state other than off then it is still
active for some reason (typically a low power function such as accessory
detection). This wasn't an issue when the feature was implemented as we
always went to _ON for any active function, subsequent power improvements
have changed things.

With the modern way of doing things we should overhaul the infrastructure
to allow devices to explicitly take references for these functions but
that's a much more invasive change and will require driver updates to
deploy, this will bring the framework into line with the existing driver
set before we do that work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Now we've switched over to regmap the ASoC level cache sync will be
ineffectual and potentially harmful as there is no longer an ASoC level
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The user reports that model=auto works better than current handling
on a 3.2 based kernel (with jack detection patches backported).
Since model=auto is what we prefer these days anyway, the quirk
should be removed.

Alsa-info for the relevant machine:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/923316/+attachment/2702812/+files/alsa-info.txt.Pbfno2x7bp

BugLink: https://bugs.launchpad.net/bugs/923316Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If a codec has both a front and a rear Line In, two controls both
named "Line Jack" will be created, which causes parsing to fail.
While a long term solution might be to name the jacks differently,
this extra check is consistent with what is already being done in many
auto-parsers, and will also protect against other cases when two
inputs have the same label.

BugLink: https://bugs.launchpad.net/bugs/923409Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>