- 06 Dec, 2011 10 commits
-
-
Hsu, Kenny authored
Create new testmode commands and attributes to suppot sram data reading. Because the amount of sram data may exceed single skb packet size. Using the nl80211 dump it funtion to deliver sram data to userspace. - IWL_TM_CMD_APP2DEV_READ_SRAM - IWL_TM_CMD_APP2DEV_DUMP_SRAM - IWL_TM_ATTR_SRAM_ADDR - IWL_TM_ATTR_SRAM_SIZE - IWL_TM_ATTR_SRAM_DUMP Signed-off-by:
Kenny Hsu <kenny.hsu@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
max_streams for AR9462 is '2'. it does not fixes anything, but improves the code readability Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
based on systems change to improve rx dynamic range, and enables heavy clip for 5G HT40 MCS0 to improve spectral mask power. also remove an unused function declaration Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Signed-off-by:
-
Larry Finger authored
A previous commit fixed a problem whereby the rtl8192c driver loaded the firmware from disk many times; however, the log message was not moved. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Alexander Simon authored
The HT mode is set by iw (previous patchsets). The interface is set into the specified HT mode. HT mode and capabilities are announced in beacons. If we add a station that uses HT also, the fastest matching HT mode will be used for transmission. That means if we are using HT40+ and we add a station running on HT40-, we would transfer at HT20. If we join an IBSS with HT40, but the secondary channel is not available, we will fall back into HT20 as well. Allow frame aggregation to start in IBSS mode. Signed-off-by:
Alexander Simon <an.alexsimon@googlemail.com> [siwu@hrz.tu-chemnitz.de: Updates] * remove implicit channel_type enum assumptions * use rate_control_rate_init() if channel type changed * remove channel flags check * activate HT IBSS feature support * slightly reword commit message * rebase on wireless-testing Signed-off-by:
Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by:
Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Simon Wunderlich authored
* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA * Send ADDBA only to HT STAs - implement 11.5.1.1 partially Signed-off-by:
-
Alexander Simon authored
Prepare cfg80211 for IBSS HT: * extend cfg80211 ibss struct with channel_type * Check if extension channel can be used * Export can_beacon_sec_chan for use in mac80211 (will be called from ibss.c later). Signed-off-by:
-
Thomas Meyer authored
The advantage of kcalloc is, that will prevent integer overflows which could result from the multiplication of number of elements and size and it is also a bit nicer to read. The semantic patch that makes this change is available in https://lkml.org/lkml/2011/11/25/107Signed-off-by:
Thomas Meyer <thomas@m3y3r.de> Signed-off-by:
-
Thomas Meyer authored
The advantage of kcalloc is, that will prevent integer overflows which could result from the multiplication of number of elements and size and it is also a bit nicer to read. The semantic patch that makes this change is available in https://lkml.org/lkml/2011/11/25/107Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
-
- 02 Dec, 2011 13 commits
-
-
Andrei Emeltchenko authored
Make sure that code match exactly what comment says about pre 1.2 bluetooth version. Since this is HCI detail lmp_ver changed to hci_ver. Signed-off-by:
Andrei Emeltchenko <andrei.emeltchenko@intel.com> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Gustavo F. Padovan <padovan@profusion.mobi>
-
Andrei Emeltchenko authored
Use bluetooth names instead of BT SIG assigned numbers Signed-off-by:
-
-
Andrei Emeltchenko authored
Check for hci_ver instead of lmp_ver Signed-off-by:
-
Cong Wang authored
This patch fixes the following memory leak reported by kmemleak: unreferenced object 0xffff880060a53840 (size 192): comm "softirq", pid 0, jiffies 4320571771 (age 1406.569s) hex dump (first 32 bytes): 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff81138a1c>] create_object+0x187/0x28b [<ffffffff814be12e>] kmemleak_alloc+0x73/0x98 [<ffffffff811289d3>] __kmalloc+0xfc/0x123 [<ffffffff81386546>] usb_alloc_urb+0x1e/0x48 [<ffffffffa0130274>] btusb_send_frame+0x86/0x385 [btusb] [<ffffffffa02d8230>] hci_send_frame+0xa0/0xa5 [bluetooth] [<ffffffffa02d8a4e>] hci_cmd_task+0xa0/0xfb [bluetooth] [<ffffffff81058548>] tasklet_action+0x8f/0xef [<ffffffff81058a4c>] __do_softirq+0xf4/0x1db [<ffffffff81058bb7>] run_ksoftirqd+0x84/0x129 [<ffffffff8106f1c4>] kthread+0xa0/0xa8 [<ffffffff814dd144>] kernel_thread_helper+0x4/0x10 [<ffffffffffffffff>] 0xffffffffffffffff The problem is that when inc_tx() returns non-zero, we forgot to call usb_free_urb(). Cc: Marcel Holtmann <marcel@holtmann.org> Cc: "Gustavo F. Padovan" <padovan@profusion.mobi> Signed-off-by:WANG Cong <amwang@redhat.com> Acked-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirelessJohn W. Linville authored
Conflicts: drivers/net/wireless/iwlwifi/iwl-agn.c drivers/net/wireless/libertas/cfg.c
-
Wey-Yi Guy authored
The current default watchdog timer is enabled, but we are seeing issues on legacy devices. So change the default setting of watchdog timer to per device based. But user still can use the "wd_disable" module parameter to overwrite the system setting Cc: stable@vger.kernel.org #3.0+ Signed-off-by:
-
Wey-Yi Guy authored
The ht40 setting should not change after association unless channel switch This fix a problem we are seeing which cause uCode assert because driver sending invalid information and make uCode confuse Here is the firmware assert message: kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000. kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301 kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump: kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6 kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1 kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2 kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1 kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2 kernel: iwlagn 0000:03:00.0: 0x01008035 | data1 kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2 kernel: iwlagn 0000:03:00.0: 0x000005A7 | line kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1 kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2 kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3 kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version kernel: iwlagn 0000:03:00.0: 0x00480303 | board version kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd kernel: iwlagn 0000:03:00.0: CSR values: kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG) kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303 kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40 kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030 kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5 kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0 kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001 kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001 kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044 kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078 kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2 kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200 kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010 kernel: iwlagn 0000:03:00.0: FH register values: kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060 kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries kernel: ------------[ cut here ]------------ WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407() kernel: Hardware name: 4290W4H kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2 kernel: Call Trace: kernel: [<ffffffff81036558>] ? warn_slowpath_common+0x73/0x87 kernel: [<ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407 kernel: [<ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32 kernel: [<ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87 kernel: [<ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3 kernel: [<ffffffff810480c9>] ? worker_thread+0x17a/0x23a kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff8104ba97>] ? kthread+0x7a/0x82 kernel: [<ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10 kernel: [<ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11 kernel: [<ffffffff813d21b0>] ? gs_change+0xb/0xb Cc: <stable@kernel.org> 3.1+ Reported-by:
Udo Steinberg <udo@hypervisor.org> Signed-off-by:
-
Johannes Berg authored
Group keys in IBSS or AP mode are not programmed into the device since we give the key to it with every TX packet. However, we do need mac80211 to create the MMIC & PN in all cases. Move the code around to set the key flags all the time. We set them even when the key is removed again but that is obviously harmless. Cc: stable@vger.kernel.org Reported-by:
Reinette Chatre <reinette.chatre@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Andrei Emeltchenko authored
Remove old code not touched for several years. Signed-off-by:
-
Andre Guedes authored
This patch adds the parameter struct and the command complete event handler to the LE Set Scan Parameter HCI command. Signed-off-by:
Andre Guedes <andre.guedes@openbossa.org> Acked-by:
-
Andre Guedes authored
This patch adds the dev_flags field to struct hci_dev. This new flags variable should be used to define flags related to BR/EDR and/or LE controller itself. It should be used to define flags which represents states from the controller. The dev_flags is cleared in case the controller sends a Reset Command Complete Event to the host. Also, this patch adds the HCI_LE_SCAN flag which was created to track if the controller is performing LE scan or not. The flag is set/cleared when the controller starts/stops scanning. This is an initial effort to stop using hdev->flags to define internal flags since it is exported to userspace by an ioctl. Signed-off-by:
-
Andrei Emeltchenko authored
Upstream Code Aurora function with minor trivial fixes. Origin: git://codeaurora.org/kernel/msm.gitSigned-off-by:
-
- 01 Dec, 2011 5 commits
-
-
John W. Linville authored
This reverts commit f785d83a. This was provoking WARNINGs from the iwlegacy drivers. Signed-off-by:
-
Brian Gix authored
Signed-off-by:
Brian Gix <bgix@codeaurora.org> Signed-off-by:
-
Brian Gix authored
The blkcipher must be freed to avoid memory leak. Signed-off-by:
-
Brian Gix authored
Some MITM scenarios require handling of the User Passkey Request event, by querying the user, and passing the response back. Signed-off-by:
-
Brian Gix authored
For some MITM protection pairing scenarios, the user is required to enter or accept a 6 digit passkey. Signed-off-by:
-
- 30 Nov, 2011 12 commits
-
-
Mohammed Shafi Shajakhan authored
the default tx/rx chainmask for AR9462 is 0x3. this patch helps to assign 0x3 rather than 0x7 for AR9462 with the help of fix_chainmask module if something goes wrong in reading tx/rx chain mask from OTP/EEPROM card(though its very unlikely) Signed-off-by:
-
Mohammed Shafi Shajakhan authored
only for AR9485 (or) later chipsets TxIQ calibration runs as part of AGC calibration. without this patch TX IQ cal completion i.e. ar9003_hw_tx_iq_cal_run won't be executed for AR9003 Reviewed-by:
Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
Axel Lin authored
It is not used outside this driver so no need to make the symbol global. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Signed-off-by:
-
Dan Carpenter authored
We should free "bus_if" here, it's a small leak but it makes the static checkers happy. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
Signed-off-by:
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
here we check for BT state and if BT calibration has started, give 25ms for BT Calibration to finish. we also take care of 2G/5G switch and LNA transfer incase WLAN is operating in 5G. in case the BT state is awake when we do WLAN calibration re-calibrate and we reset the message exchange between WLAN and BT. BT is given preference when simultaneous CAL request happens. calibration for WLAN/BT is done assuming that the other co-existing module is in awake state, if not we continue to do calibration while if the other module's state changes we need to do restart the calibration handshake Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
WLAN communicates with BT for its calibration by sending WLAN_CAL_REQ, waits for BT_CAL_GRANT. This is done with the help of GPM messages. also WLAN_CAL_DONE messages is sent once WLAN calibration is done. Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
send halt BT GPM if the chip is in network sleep and BT state is awake Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
required buffers and dma allocation is done for GPM and SCHED messages Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
