These are the chipIDs of some ARM based SoCs from the BCM47xx line.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To make it possible to use the SoC host interface with ARM SoCs do not
depend on the MIPS driver any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These cores were found on a BCM4708 (chipid 53010), this is a ARM SoC
with two Cortex A9 cores.

bcma: bus0: Found chip with id 0xCF12, rev 0x00 and package 0x02
bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
bcma: bus0: Core 1 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0)
bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 6 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 8 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0)
bcma: bus0: Core 9 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0)
bcma: bus0: Core 10 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0)
bcma: bus0: Core 11 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
bcma: bus0: Core 12 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
bcma: bus0: Core 13 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
bcma: bus0: Core 14 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
bcma: bus0: Core 15 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
bcma: bus0: Core 16 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Finish all SW context modifications prior to notifying hardware

It used to be race condition: if HW finish Tx and issue Tx completion IRQ very fast,
prior to SW context update in wil_tx_vring, Tx completion will mis-handle descriptor, as
SW part will have no skb pointer stored.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable adding more data to the SW context.
For now, add flag "mapped_as_page", to separate decisions on free-ing skb
and type of DMA mapping.
This allows linking skb itself to any descriptor of fragmented skb.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No need to modify HW descriptor, as it will be re-initialized on Tx.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When destroying Rx vring, branch for Rx used wrong Tx descriptor:
while SW context was taken for "head", HW descriptor was, by mistake,
taken from "tail"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

FW guys changed header structure; align driver code
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Linksys AE3000 device is based on the RT3573
chipset. The support for this chipset is available
already, and the AE3000 device works with the driver.

Only managed mode works correctly at the moment,
for AP mode additional changes are needed in the
driver.

Also add a new RT2800USB_RT3573 Kconfig option and
only enable support for RT3573 based devices if
that is enabled.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The RT3593 chipset requires different [RT]XWI size
values. Modify the driver to use the correct values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Support for the RT3593 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Support for the RF3053 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_ChipSwitchChannel in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  FreqItems3053 in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The actual code uses two default TX power values.
This is enough for 1T and for 2T devices however
on 3T devices another value is needed for the third
chain.

Add a new field to struct channel_info and initialize
it from the 'rt2800_probe_hw_mode' function. Also modify
the 'rt2800_config_channel' to handle the new field as
well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The LNA_A[12] gain values are stored at a different
offset in the EEPROM on RT3593 based devices. However
the current code unconditionally reads those values
from the location used by other chipsets.

Fix the code to use the correct EEPROM offset.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN1_24G_READ in include/chip/rt3593.h
  RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN2_5G_READ in include/chip/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The reference code uses hardcoded zero TX mixer gain value
for RT3593. Do the same in the rt2x00 driver.

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  NICReadEEPROMParameters in common/rtmp_init.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move the TX mixer gain reading code into separate
helper functions in preparation for RT3593 support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The TX power values in the EEPROM are using
a different format for the RT3593 chip. The
default TX power value uses bits 0..4 only.
Bits 5..8 contains value for fine grained
power control. Additionally, the lower and
upper limits of the TX power values are the
same for both bands.

Improve the rt2800_txpower_to_dev function,
in order to compute the correct default power
values for the RT3593 chip as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Introduce a new helper function for converting
the default TX power values from EEPROM into
mac80211 values.

The change improves the readability and it makes
it easier to add support for other chipsets.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On the RT3593 chipset, BBP register 86 must be
configured by different values based on the RX
antenna numbers.

Configure this register from the 'rt2800_config_ant'
function.

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_CONFIG_SET_BY_ANTENNA in include/chip/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The field must be set to 2 instead of 0 for
devices with three TX chains.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  RTMPReadTxPwrPerRateExt in chips/rt3593.c
  RT3593_AsicGetTxPowerOffset in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_PostBBPInitialization in chips/rt3553.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  NICInitRT3593RFRegisters in chips/rt3593.c
  RT3593LoadRFNormalModeSetup in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  NICInitRT3593BbpRegisters in chips/rt3593.c
  NICInitBBP in common/rtmp_init.c
  NICInitAsicFromEEPROM in common/rtmp_init.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  NICInitRT3593MacRegisters in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Three-chain devices are using a different
EEPROM layout than the rest of the chipsets.
Add a new map which describes the new layout
and use that for the RT3593 chipset.

The index values has been computed from the
EEPROM_EXT_* defines, which can be found in
the 'include/chip/rt3593.h' file in the
Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of assign the offset value to the
enum directly use a new helper function to
convert a rt2800_eeprom_word enum into an
index of the rt2x00_dev->eeprom array.

The patch does not change the existing
behaviour, but makes it possible to add
support for three-chain devices which are
using a different EEPROM layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a new helper function and use that for reading
single elements of various arrays in the EEPROM.

The patch does not change the current behaviour,
but it allows to use sequential values for the
rt2800_eeprom_word enums. The conversion will be
implemented in a subsequent change.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch adds rt2800 specific functions for
EEPROM data access and changes the code to use
these instead of the generic rt2x00_eeprom_*
variants.

To avoid functional changes, the new functions
are wrappers around the corresponding generic
rt2x00_eeprom_* routines for now. Functional
changes will be implemented in additional patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch converts the EEPROM_* word address defines
into new enum values. The new enum type will be used
by new functions which will be introduced in subsequent
changes.

The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, RTS threshold is not handled for HT. Handle
user-specified threshold values for both aggregated
and unaggregated frames. Use the wiphy's threshold
parameter for now, it can be made per-VIF later on.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the platform doesn't have rfkill support, i.e. nothing
is connected to the rfkill GPIO, there's little value in
polling the GPIO. Add a Kconfig option to allow disabling
the polling in ath9k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert the mwifiex/pci driver to use dev_pm_ops for power management and
remove Legacy PM handling. This change re-uses existing suspend and resume
interfaces for dev_pm_ops, and changes CONFIG_PM ifdefs to CONFIG_PM_SLEEP
as the driver does not support run-time PM.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pull slab update from Pekka Enberg:
 "Highlights:

  - Fix for boot-time problems on some architectures due to
    init_lock_keys() not respecting kmalloc_caches boundaries
    (Christoph Lameter)

  - CONFIG_SLUB_CPU_PARTIAL requested by RT folks (Joonsoo Kim)

  - Fix for excessive slab freelist draining (Wanpeng Li)

  - SLUB and SLOB cleanups and fixes (various people)"

I ended up editing the branch, and this avoids two commits at the end
that were immediately reverted, and I instead just applied the oneliner
fix in between myself.

* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
  slub: Check for page NULL before doing the node_match check
  mm/slab: Give s_next and s_stop slab-specific names
  slob: Check for NULL pointer before calling ctor()
  slub: Make cpu partial slab support configurable
  slab: add kmalloc() to kernel API documentation
  slab: fix init_lock_keys
  slob: use DIV_ROUND_UP where possible
  slub: do not put a slab to cpu partial list when cpu_partial is 0
  mm/slub: Use node_nr_slabs and node_nr_objs in get_slabinfo
  mm/slub: Drop unnecessary nr_partials
  mm/slab: Fix /proc/slabinfo unwriteable for slab
  mm/slab: Sharing s_next and s_stop between slab and slub
  mm/slab: Fix drain freelist excessively
  slob: Rework #ifdeffery in slab.h
  mm, slab: moved kmem_cache_alloc_node comment to correct place

In the -rt kernel (mrg), we hit the following dump:

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
PGD a2d39067 PUD b1641067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: sunrpc cpufreq_ondemand ipv6 tg3 joydev sg serio_raw pcspkr k8temp amd64_edac_mod edac_core i2c_piix4 e100 mii shpchp ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom sata_svw ata_generic pata_acpi pata_serverworks radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core dm_mirror dm_region_hash dm_log dm_mod
CPU 3
Pid: 20878, comm: hackbench Not tainted 3.6.11-rt25.14.el6rt.x86_64 #1 empty empty/Tyan Transport GT24-B3992
RIP: 0010:[<ffffffff811573f1>]  [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
RSP: 0018:ffff8800a9b17d70  EFLAGS: 00010213
RAX: 0000000000000000 RBX: 0000000001200011 RCX: ffff8800a06d8000
RDX: 0000000004d92a03 RSI: 00000000000000d0 RDI: ffff88013b805500
RBP: ffff8800a9b17dc0 R08: ffff88023fd14d10 R09: ffffffff81041cbd
R10: 00007f4e3f06e9d0 R11: 0000000000000246 R12: ffff88013b805500
R13: ffff8801ff46af40 R14: 0000000000000001 R15: 0000000000000000
FS:  00007f4e3f06e700(0000) GS:ffff88023fd00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 00000000a2d3a000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process hackbench (pid: 20878, threadinfo ffff8800a9b16000, task ffff8800a06d8000)
Stack:
 ffff8800a9b17da0 ffffffff81202e08 ffff8800a9b17de0 000000d001200011
 0000000001200011 0000000001200011 0000000000000000 0000000000000000
 00007f4e3f06e9d0 0000000000000000 ffff8800a9b17e60 ffffffff81041cbd
Call Trace:
 [<ffffffff81202e08>] ? current_has_perm+0x68/0x80
 [<ffffffff81041cbd>] copy_process+0xdd/0x15b0
 [<ffffffff810a2125>] ? rt_up_read+0x25/0x30
 [<ffffffff8104369a>] do_fork+0x5a/0x360
 [<ffffffff8107c66b>] ? migrate_enable+0xeb/0x220
 [<ffffffff8100b068>] sys_clone+0x28/0x30
 [<ffffffff81527423>] stub_clone+0x13/0x20
 [<ffffffff81527152>] ? system_call_fastpath+0x16/0x1b
Code: 89 fc 89 75 cc 41 89 d6 4d 8b 04 24 65 4c 03 04 25 48 ae 00 00 49 8b 50 08 4d 8b 28 49 8b 40 10 4d 85 ed 74 12 41 83 fe ff 74 27 <48> 8b 00 48 c1 e8 3a 41 39 c6 74 1b 8b 75 cc 4c 89 c9 44 89 f2
RIP  [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
 RSP <ffff8800a9b17d70>
CR2: 0000000000000000
---[ end trace 0000000000000002 ]---

Now, this uses SLUB pretty much unmodified, but as it is the -rt kernel
with CONFIG_PREEMPT_RT set, spinlocks are mutexes, although they do
disable migration. But the SLUB code is relatively lockless, and the
spin_locks there are raw_spin_locks (not converted to mutexes), thus I
believe this bug can happen in mainline without -rt features. The -rt
patch is just good at triggering mainline bugs ;-)

Anyway, looking at where this crashed, it seems that the page variable
can be NULL when passed to the node_match() function (which does not
check if it is NULL). When this happens we get the above panic.

As page is only used in slab_alloc() to check if the node matches, if
it's NULL I'm assuming that we can say it doesn't and call the
__slab_alloc() code. Is this a correct assumption?
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more vfs stuff from Al Viro:
 "O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
  making simple_lookup() usable for filesystems with non-NULL s_d_op,
  which allows us to get rid of quite a bit of ugliness"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  sunrpc: now we can just set ->s_d_op
  cgroup: we can use simple_lookup() now
  efivarfs: we can use simple_lookup() now
  make simple_lookup() usable for filesystems that set ->s_d_op
  configfs: don't open-code d_alloc_name()
  __rpc_lookup_create_exclusive: pass string instead of qstr
  rpc_create_*_dir: don't bother with qstr
  llist: llist_add() can use llist_add_batch()
  llist: fix/simplify llist_add() and llist_add_batch()
  fput: turn "list_head delayed_fput_list" into llist_head
  fs/file_table.c:fput(): add comment
  Safer ABI for O_TMPFILE