Change gsi_irq_setup() so it returns an error value, and introduce
gsi_irq_teardown() as its inverse.  Set the interrupt type (IRQ
rather than MSI) in gsi_irq_setup().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move gsi_irq_setup() and gsi_ring_setup() so they're defined right
above gsi_setup() where they're called.  This is a trivial movement
of code to prepare for upcoming patches.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the Boolean flags passed to __gsi_channel_start() and
__gsi_channel_stop() so they represent whether the request is being
made to implement suspend (versus stop) or resume (versus start).

Then stop or start the channel for suspend/resume requests only if
the hardware version indicates it should be done.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GSI layer has the IPA version now, so there's no need for
version-specific flags to be passed from IPA.  One instance of
this is in gsi_channel_suspend() and gsi_channel_resume(), which
indicate whether or not the endpoint suspend is implemented by
GSI stopping the channel.  We can make that determination based
on gsi->version, eliminating the need for a Boolean flag in those
functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Loic Poulain says:

====================
net: mhi: move MBIM to WWAN

Implement a proper WWAN driver for MBIM network protocol, with multi link
management supported through the WWAN framework (wwan rtnetlink).

Until now, MBIM over MHI was supported directly in the mhi_net driver, via
some protocol rx/tx fixup callbacks, but with only one session supported
(no multilink muxing). We can then remove that part from mhi_net and restore
the driver to a simpler version for 'raw' ip transfer (or QMAP via rmnet link).

Note that a wwan0 link is created by default for session-id 0. Additional links
can be managed via ip tool:

    $ ip link add dev wwan0mms parentdev wwan0 type wwan linkid 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The MBIM protocol has now been integrated in a proper WWAN driver. We
can then revert back to a simpler driver for mhi_net, which is used
for raw IP or QMAP protocol (via rmnet link).

- Remove protocol management
- Remove WWAN framework usage (only valid for mbim)
- Remove net/mhi directory for simpler mhi_net.c file
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new wwan driver for MBIM over MHI. MBIM is a transport protocol
for IP packets, allowing packet aggregation and muxing. Initially
designed for USB bus, it is also exposed through MHI bus for QCOM
based PCIe wwan modems.

This driver supports the new wwan rtnetlink interface for multi-link
management and has been tested with Quectel EM120R-GL M2 module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: add netif_set_real_num_queues() for device reconfig

This short set adds a helper to make the implementation of
two-phase NIC reconfig easier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid reconfig problems due to failures in netif_set_real_num_tx_queues()
by using netif_set_real_num_queues().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_set_real_num_rx_queues() and netif_set_real_num_tx_queues()
can fail which breaks drivers trying to implement reconfiguration
in a way that can't leave the device half-broken. In other words
those functions are incompatible with prepare/commit approach.

Luckily setting real number of queues can fail only if the number
is increased, meaning that if we order operations correctly we
can guarantee ending up with either new config (success), or
the old one (on error).

Provide a helper implementing such logic so that drivers don't
have to duplicate it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass extack arg to validate_linkmsg and validate_link_af callbacks.
If a netlink attribute has a reject_message, use the extended ack
mechanism to carry the message back to user space.
Signed-off-by: Rocco Yue <rocco.yue@mediatek.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds OOB support for AF_UNIX sockets.
The semantics is same as TCP.

The last byte of a message with the OOB flag is
treated as the OOB byte. The byte is separated into
a skb and a pointer to the skb is stored in unix_sock.
The pointer is used to enforce OOB semantics.
Signed-off-by: Rao Shoaib <rao.shoaib@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-switch: integrate the MAC endpoint support

This patch set integrates the already available MAC support into the
dpaa2-switch driver as well.

The first 4 patches are fixing up some minor problems or optimizing the
code, while the remaining ones are actually integrating the dpaa2-mac
support into the switch driver by calling the dpaa2_mac_* provided
functions. While at it, we also export the MAC statistics in ethtool
like we do for dpaa2-eth.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If a switch port is connected to a MAC, use the common dpaa2-mac support
for exporting the available MAC statistics.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the next patch, we'll add support for also exporting the MAC
statistics in the ethtool stats. Annotate already present HW stats with
a suggestive prefix.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Integrate the common MAC endpoint management support into the
dpaa2-switch driver as well. Nothing special happens here, just that the
already available dpaa2-mac functions are also called from dpaa2-switch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of a switch DPAA2 object, the interface ID is also needed when
querying for the object endpoint. Extend fsl_mc_get_endpoint() so that
users can also pass the interface ID that are interested in.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The call to dpaa2_switch_port_link_state_update is a leftover from the
time when on DPAA2 platforms the PHYs were started at boot time so when
an ifconfig was issued on the associated interface, the link status
needed to be checked directly from the ndo_open() callback.  This is not
needed anymore since we are now properly integrated with the PHY layer
thus a link interrupt will come directly from the PHY eventually without
the need to call the sync function.
Fix this up by removing the call to dpaa2_switch_port_link_state_update.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not enable the switch interfaces at probe time since this is
trigged by the open callback. Remove the call dpsw_enable() which does
exactly this.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MC firmware supplies us the switch interface index for which an
interrupt was triggered. Use this to our advantage instead of looping
through all the switch ports and doing unnecessary work.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Request all interrupt sources to be read and then cleared on the DPSW
object. In the next patches we'll also add support for treating other
interrupts.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch intends to fix MAC internal delay doesn't work, due to use
of_property_read_u32() incorrectly, and improve this feature a bit:
1) check the delay value if valid, only program register when it's 2000ps.
2) only enable "enet_2x_txclk" clock when require MAC internal delay.

Fixes: fc539459 ("net: fec: add MAC internal delayed clock feature support")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20210803052424.19008-1-qiangqing.zhang@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Dan Carpenter's smatch tests report that the "vid" variable, populated
by sja1105_vlan_rcv when an skb is received by the tagger that has a
VLAN ID which cannot be decoded by tag_8021q, may be uninitialized when
used here:

	if (source_port == -1 || switch_id == -1)
		skb->dev = dsa_find_designated_bridge_port_by_vid(netdev, vid);

The sja1105 driver, by construction, sets up the switch in a way that
all data plane packets sent towards the CPU port are VLAN-tagged. So it
is practically impossible, in a functional system, for a packet to be
processed by sja1110_rcv() which is not a control packet and does not
have a VLAN header either.

However, it would be nice if the sja1105 tagging driver could
consistently do something valid, for example fail, even if presented with
packets that do not hold valid sja1105 tags. Currently it is a bit hard
to argue that it does that, given the fact that a data plane packet with
no VLAN tag will trigger a call to dsa_find_designated_bridge_port_by_vid
with a vid argument that is an uninitialized stack variable.

To fix this, we can initialize the u16 vid variable with 0, a value that
can never be a bridge VLAN, so dsa_find_designated_bridge_port_by_vid
will always return a NULL skb->dev.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210802195137.303625-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Nikolay points out that it is incorrect to assume that it is impossible
to have an fdb entry with fdb->dst == NULL and the BR_FDB_LOCAL bit in
fdb->flags not set. This is because there are reader-side places that
test_bit(BR_FDB_LOCAL, &fdb->flags) without the br->hash_lock, and if
the updating of the FDB entry happens on another CPU, there are no
memory barriers at writer or reader side which would ensure that the
reader sees the updates to both fdb->flags and fdb->dst in the same
order, i.e. the reader will not see an inconsistent FDB entry.

So we must be prepared to deal with FDB entries where fdb->dst and
fdb->flags are in a potentially inconsistent state, and that means that
fdb->dst == NULL should remain a condition to pick the net_device that
we report to switchdev as being the bridge device, which is what the
code did prior to the blamed patch.

Fixes: 52e4bec1 ("net: bridge: switchdev: treat local FDBs the same as entries towards the bridge")
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210802113633.189831-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit b79c6fba, reversing
these changes made to 0ac26271:

  commit 6a0eb6c9 ("dt-bindings: net: qcom,ipa: make imem interconnect
                       optional")
  commit f8bd3c82 ("arm64: dts: qcom: sc7280: add IPA information")
  commit fd0f72c3 ("arm64: dts: qcom: sc7180: define ipa_fw_mem node")

I intend for these commits to go through the Qualcomm repository, to
avoid conflicting with other activity being merged there.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210802233019.800250-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There is a spelling mistake in a NL_SET_ERR_MSG_MOD message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210803105617.338546-1-colin.king@canonical.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

fib_treeref needs to be set after kzalloc. The old code had a ++ which
led to the confusion when the int was replaced by a refcount_t.

Fixes: 79976892 ("net: convert fib_treeref from int to refcount_t")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210803073739.22339-1-yajun.deng@linux.devSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Arnd Bergmann says:

====================
drivers/net/Space.c cleanup

I discovered that there are still a couple of drivers that rely on
beiong statically initialized from drivers/net/Space.c the way
we did in the last century. As it turns out, there are a couple
of simplifications that can be made here, as well as some minor
bugfixes.

There are four classes of drivers that use this:

- most 10mbit ISA bus ethernet drivers (and one 100mbit one)
- both ISA localtalk drivers
- several m68k ethernet drivers
- one obsolete WAN driver

I found that the drivers using in arch/m68k/ don't actually benefit
from being probed this way as they do not rely on the netdev= command
line arguments, they have simply never been changed to work like a
modern driver.

I had previously sent a patch to remove the sbni/granch driver, and
there were no objections to this patch but forgot to resend it after
some discussion about another patch in the same series.

For the ISA drivers, there is usually no way to probe multiple devices
at boot time other than the netdev= arguments, so all that logic is left
in place for the moment, but centralized in a single file that only gets
included in the kernel build if one or more of the drivers are built-in.

I'm also changing the old-style init_module() functions in these drivers
to static functions with a module_init() annotation, to more closely
resemble modern drivers. These are the last drivers in the kernel to
still use init_module/cleanup_module, removing those may enable future
cleanups to the module loading process.

       Arnd

Changes in v2:

- replace xsurf100 change with Michael's version
- make it PATCH instead of RFC
- rebase to net-next as of August 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a couple of ISA ethernet drivers that use the old
init_module/cleanup_module function names for the main entry
points, nothing else uses those any more.

Change them to the documented method with module_init()
and module_exit() markers next to static functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is one of very few drivers using the old init_module/cleanup_module
function names. Change it over to the modern method.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver was merged in 1999 and has only ever seen treewide cleanups
since then, with no indication whatsoever that anyone has actually
had access to hardware for testing the patches.

>From the information in the link below, it appears that the hardware
is for some leased line system in Russia that has since been
discontinued, and useless without any remote end to connect to.

As the driver still feels like a Linux-2.2 era artifact today, it
appears that the best way forward is to just delete it.

Link: https://www.tms.ru/%D0%90%D0%B4%D0%B0%D0%BF%D1%82%D0%B5%D1%80_%D0%B4%D0%BB%D1%8F_%D0%B2%D1%8B%D0%B4%D0%B5%D0%BB%D0%B5%D0%BD%D0%BD%D1%8B%D1%85_%D0%BB%D0%B8%D0%BD%D0%B8%D0%B9_Granch_SBNI12-10Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dscc4 driver was removed in 2019 but these Kconfig entries remain,
so remove them as well.

Fixes: 28c9eb90 ("net/wan: dscc4: remove broken dscc4 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are very few ISA drivers left that rely on the static probing from
drivers/net/Space.o. Make them all select a new CONFIG_NETDEV_LEGACY_INIT
symbol, and drop the entire probe logic when that is disabled.

The 9 drivers that are called from Space.c are the same set that
calls netdev_boot_setup_check().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is now only used by a handful of old ISA drivers,
and can be moved into the file they already all depend on.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that ax88796.c exports the ax_NS8390_reinit() symbol, we can
include 8390.h instead of lib8390.c, avoiding duplication of that
function and killing a few compile warnings in the bargain.

Fixes: 861928f4 ("net-next: New ax88796 platform
driver for Amiga X-Surf 100 Zorro board (m68k)")
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The block I/O code for the new X-Surf 100 ax88796 driver needs
ax_NS8390_init() for error fixup in its block_output function.

Export this static function through the ax_NS8390_reinit()
wrapper so we can lose the lib8380.c include in the X-Surf 100
driver.

[arnd: add the declaration in the header to avoid a
 -Wmissing-prototypes warning]
Fixes: 861928f4 ("net-next: New ax88796 platform
driver for Amiga X-Surf 100 Zorro board (m68k)")
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are six m68k specific drivers that use the legacy probe method
in drivers/net/Space.c. However, all of these only support a single
device, and they completely ignore the command line settings from
netdev_boot_setup_check, so there is really no point at all.

Aside from sun3_82586, these already have a module_init function that
can be used for built-in mode as well, simply by removing the #ifdef.

Note that the 82596 driver was previously used on ISA as well, but
that got dropped long ago.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two drivers in the cs89x0 file, with the CONFIG_CS89x0_PLATFORM
symbol deciding which one is getting built. This is somewhat confusing
and makes it more likely ton configure a driver that works nowhere.

Split up the Kconfig option into separate ISA and PLATFORM drivers,
with the ISA symbol explicitly connecting to the static probing in
drivers/net/Space.c

The two drivers are still mutually incompatible at compile time,
which could be lifted by splitting them into multiple files,
but in practice this will make no difference.

The platform driver can now be enabled for compile-testing on
non-ARM machines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver never uses the information returned by
netdev_boot_setup_check, and is not called by the boot-time probing from
driver/net/Space.c, so just remove these stale references.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver never relies on the netdev_boot_setup_check()
to get its configuration, so it can just as well do its
own probing all the time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>