- 06 Apr, 2015 2 commits
-
-
Kristina Martšenko authored
commit 86bf7f3e upstream. Reading a channel through sysfs, or starting a buffered capture, will currently turn off the touchscreen. This is because the read_raw() and buffer preenable()/postdisable() callbacks disable interrupts for all LRADC channels, including those the touchscreen uses. So make the callbacks only disable interrupts for the channels they use. This means channel 0 for read_raw() and channels 0-5 for the buffer (if the touchscreen is enabled). Since the touchscreen uses different channels (6 and 7), it no longer gets turned off. Note that only i.MX28 is affected by this issue, i.MX23 should be fine. Signed-off-by:
Kristina Martšenko <kristina.martsenko@gmail.com> Reviewed-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Kristina Martšenko authored
commit f81197b8 upstream. The touchscreen was initially designed [1] to map all of its physical channels to one virtual channel, leaving buffered capture to use the remaining 7 virtual channels. When the touchscreen was reimplemented [2], it was made to use four virtual channels, which overlap and conflict with the channels the buffer uses. As a result, when the buffer is enabled, the touchscreen's virtual channels are remapped to whichever physical channels the buffer was configured with, causing the touchscreen to read those instead of the touch measurement channels. Effectively the touchscreen stops working. So here we separate the channels again, giving the touchscreen 2 virtual channels and the buffer 6. We can't give the touchscreen just 1 channel as before, as the current pressure calculation requires 2 channels to be read at the same time. This makes the touchscreen continue to work during buffered capture. It has been tested on i.MX28, but not on i.MX23. [1] 06ddd353 ("iio: mxs: Implement support for touchscreen") [2] dee05308 ("Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection") Signed-off-by:
-
- 03 Apr, 2015 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 02 Apr, 2015 37 commits
-
-
Seth Forshee authored
commit 6d00f37e upstream. d1c7e29e (HID: i2c-hid: prevent buffer overflow in early IRQ) changed hid_get_input() to read ihid->bufsize bytes, which can be more than wMaxInputLength. This is the case with the Dell XPS 13 9343, and it is causing events to be missed. In some cases the missed events are releases, which can cause the cursor to jump or freeze, among other problems. Limit the number of bytes read to min(wMaxInputLength, ihid->bufsize) to prevent such problems. Fixes: d1c7e29e "HID: i2c-hid: prevent buffer overflow in early IRQ" Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Ryusuke Konishi authored
commit 957ed60b upstream. Each inode of nilfs2 stores a root node of a b-tree, and it turned out to have a memory overrun issue: Each b-tree node of nilfs2 stores a set of key-value pairs and the number of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as a few other "bn_*" members. Since the value of "bn_nchildren" is used for operations on the key-values within the b-tree node, it can cause memory access overrun if a large number is incorrectly set to "bn_nchildren". For instance, nilfs_btree_node_lookup() function determines the range of binary search with it, and too large "bn_nchildren" leads nilfs_btree_node_get_key() in that function to overrun. As for intermediate b-tree nodes, this is prevented by a sanity check performed when each node is read from a drive, however, no sanity check has been done for root nodes stored in inodes. This patch fixes the issue by adding missing sanity check against b-tree root nodes so that it's called when on-memory inodes are read from ifile, inode metadata file. Signed-off-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Catalin Marinas authored
commit 9d42d48a upstream. The native (64-bit) sigval_t union contains sival_int (32-bit) and sival_ptr (64-bit). When a compat application invokes a syscall that takes a sigval_t value (as part of a larger structure, e.g. compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t union is converted to the native sigval_t with sival_int overlapping with either the least or the most significant half of sival_ptr, depending on endianness. When the corresponding signal is delivered to a compat application, on big endian the current (compat_uptr_t)sival_ptr cast always returns 0 since sival_int corresponds to the top part of sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int is copied to the compat_siginfo_t structure. Reported-by:
Bamvor Jian Zhang <bamvor.zhangjian@huawei.com> Tested-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Alex Deucher authored
commit dbfb00c3 upstream. The logic was reversed from what the hw actually exposed. Fixes graphics corruption in certain harvest configurations. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 3d2d98ee upstream. Just in case it hasn't been calculated for the mode. Signed-off-by:
-
Tomáš Hodek authored
commit d1901ef0 upstream. When a drive is marked write-mostly it should only be the target of reads if there is no other option. This behaviour was broken by commit 9dedf603 md/raid1: read balance chooses idlest disk for SSD which causes a write-mostly device to be *preferred* is some cases. Restore correct behaviour by checking and setting best_dist_disk and best_pending_disk rather than best_disk. We only need to test one of these as they are both changed from -1 or >=0 at the same time. As we leave min_pending and best_dist unchanged, any non-write-mostly device will appear better than the write-mostly device. Reported-by:
Tomáš Hodek <tomas.hodek@volny.cz> Reported-by:
Dark Penguin <darkpenguin@yandex.ru> Signed-off-by:
NeilBrown <neilb@suse.de> Link: http://marc.info/?l=linux-raid&m=135982797322422 Fixes: 9dedf603Signed-off-by:
-
James Hogan authored
commit c2996cb2 upstream. The KSTK_EIP() and KSTK_ESP() macros should return the user program counter (PC) and stack pointer (A0StP) of the given task. These are used to determine which VMA corresponds to the user stack in /proc/<pid>/maps, and for the user PC & A0StP in /proc/<pid>/stat. However for Meta the PC & A0StP from the task's kernel context are used, resulting in broken output. For example in following /proc/<pid>/maps output, the 3afff000-3b021000 VMA should be described as the stack: # cat /proc/self/maps ... 100b0000-100b1000 rwxp 00000000 00:00 0 [heap] 3afff000-3b021000 rwxp 00000000 00:00 0 And in the following /proc/<pid>/stat output, the PC is in kernel code (1074234964 = 0x40078654) and the A0StP is in the kernel heap (1335981392 = 0x4fa17550): # cat /proc/self/stat 51 (cat) R ... 1335981392 1074234964 ... Fix the definitions of KSTK_EIP() and KSTK_ESP() to use task_pt_regs(tsk)->ctx rather than (tsk)->thread.kernel_context. This gets the registers from the user context stored after the thread info at the base of the kernel stack, which is from the last entry into the kernel from userland, regardless of where in the kernel the task may have been interrupted, which results in the following more correct /proc/<pid>/maps output: # cat /proc/self/maps ... 0800b000-08070000 r-xp 00000000 00:02 207 /lib/libuClibc-0.9.34-git.so ... 100b0000-100b1000 rwxp 00000000 00:00 0 [heap] 3afff000-3b021000 rwxp 00000000 00:00 0 [stack] And /proc/<pid>/stat now correctly reports the PC in libuClibc (134320308 = 0x80190b4) and the A0StP in the [stack] region (989864576 = 0x3b002280): # cat /proc/self/stat 51 (cat) R ... 989864576 134320308 ... Reported-by:
Alexey Brodkin <Alexey.Brodkin@synopsys.com> Reported-by:
Vineet Gupta <Vineet.Gupta1@synopsys.com> Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by:
-
Takashi Iwai authored
commit 70372a75 upstream. When a PCM draining is performed to an empty stream that has been already in PREPARED state, the current code just ignores and leaves as it is, although the drain is supposed to set all such streams to SETUP state. This patch covers that overlooked case. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Nicolas Saenz Julienne authored
commit 2f97c20e upstream. The gpio_chip operations receive a pointer the gpio_chip struct which is contained in the driver's private struct, yet the container_of call in those functions point to the mfd struct defined in include/linux/mfd/tps65912.h. Signed-off-by:
Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Hans Holmberg authored
commit 9cf75e9e upstream. The change: 7b8792bb gpiolib: of: Correct error handling in of_get_named_gpiod_flags assumed that only one gpio-chip is registred per of-node. Some drivers register more than one chip per of-node, so adjust the matching function of_gpiochip_find_and_xlate to not stop looking for chips if a node-match is found and the translation fails. Fixes: 7b8792bb ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags") Signed-off-by:
Hans Holmberg <hans.holmberg@intel.com> Acked-by:
Alexandre Courbot <acourbot@nvidia.com> Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Tested-by:
Tyler Hall <tylerwhall@gmail.com> Signed-off-by:
-
Jan Kara authored
commit dfcc70a8 upstream. For filesystems without separate project quota inode field in the superblock we just reuse project quota file for group quotas (and vice versa) if project quota file is allocated and we need group quota file. When we reuse the file, quota structures on disk suddenly have wrong type stored in d_flags though. Nobody really cares about this (although structure type reported to userspace was wrong as well) except that after commit 14bf61ff (quota: Switch ->get_dqblk() and ->set_dqblk() to use bytes as space units) assertion in xfs_qm_scall_getquota() started to trigger on xfs/106 test (apparently I was testing without XFS_DEBUG so I didn't notice when submitting the above commit). Fix the problem by properly resetting ddq->d_flags when running quotacheck for a quota file. Reported-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
Jan Kara <jack@suse.cz> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Rodrigo Vivi authored
commit 0dc6f20b upstream. When reviewing patch that fixes VGA on BDW Halo Jani noticed that we also had other ULT IDs that weren't listed there. So this follow-up patch add these pci-ids as halo and fix comments on i915_pciids.h Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> [ kamal: backport to 3.13-stable: context ] Signed-off-by:
-
Takashi Iwai authored
commit 6426460e upstream. BIOS doesn't seem to set up pins for 5.1 and the SPDIF out, so we need to give explicitly here. Reported-and-tested-by:
Misan Thropos <misanthropos@gmx.de> Signed-off-by:
-
Hui Wang authored
commit af95b414 upstream. We have a HP machine which use the codec node 0x17 connecting the internal speaker, and from the node capability, we saw the EAPD, if we don't set the EAPD on for this node, the internal speaker can't output any sound. BugLink: https://bugs.launchpad.net/bugs/1436745Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 4ff0f034 upstream. The right check for conf_reg to be invalid it testing against -1 not 0 as is done in the rest of the driver. This fixes an oops that can be triggered by: cat /sys/kernel/debug/pinctrl/43fac000.iomuxc/* Fixes: ae75ff81 ("pinctrl: pinctrl-imx: add imx pinctrl core driver") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Sergey Ryazanov authored
commit 8bfae4f9 upstream. Sometimes while CPU have some load and ath5k doing the wireless interface reset the whole WiSoC completely freezes. Set of tests shows that using atomic delay function while we wait interface reset helps to avoid such freezes. The easiest way to reproduce this issue: create a station interface, start continous scan with wpa_supplicant and load CPU by something. Or just create multiple station interfaces and put them all in continous scan. This patch partially reverts the commit 1846ac3d ("ath5k: Use usleep_range where possible"), which replaces initial udelay() by usleep_range(). I do not know actual source of this issue, but all looks like that HW freeze is caused by transaction on internal SoC bus, while wireless block is in reset state. Also I should note that I do not know how many chips are affected, but I did not see this issue with chips, other than AR5312. CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Fixes: 1846ac3d ("ath5k: Use usleep_range where possible") Reported-by:
Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by:
Eric Bree <ebree@nltinc.com> Signed-off-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Dan Carpenter authored
commit e4940626 upstream. The problem here is that we check: if (dev >= SNDRV_CARDS) Then we increment "dev". if (!joystick_port[dev++]) Then we use it as an offset into a array with SNDRV_CARDS elements. if (!request_region(joystick_port[dev], 8, "Riptide gameport")) { This has 3 effects: 1) If you use the module option to specify the joystick port then it has to be shifted one space over. 2) The wrong error message will be printed on failure if you have over 32 cards. 3) Static checkers will correctly complain that are off by one. Fixes: db1005ec ('ALSA: riptide - Fix joystick resource handling') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Sergei Shtylyov authored
commit 2e9dcdae upstream. In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit # should be no higher than 15, however the corresponding check is obviously off- by-one. Fixes: 04577994 ("clk: gate: add CLK_GATE_HIWORD_MASK") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Michael Turquette <mturquette@linaro.org> Signed-off-by:
-
Martin KaFai Lau authored
commit 3b471175 upstream. ipv6_cow_metrics() currently assumes only DST_HOST routes require dynamic metrics allocation from inetpeer. The assumption breaks when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric. Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set() is called after the route is created. This patch creates the metrics array (by calling dst_cow_metrics_generic) in ipv6_cow_metrics(). Test: radvd.conf: interface qemubr0 { AdvLinkMTU 1300; AdvCurHopLimit 30; prefix fd00:face:face:face::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; }; Before: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec fe80::/64 dev eth0 proto kernel metric 256 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec After: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec mtu 1300 fe80::/64 dev eth0 proto kernel metric 256 mtu 1300 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec mtu 1300 hoplimit 30 Fixes: 8e2ec639 (ipv6: don't use inetpeer to store metrics for routes.) Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sabrina Dubroca authored
commit 7744b5f3 upstream. This patch fixes two issues in UDP checksum computation in pktgen. First, the pseudo-header uses the source and destination IP addresses. Currently, the ports are used for IPv4. Second, the UDP checksum covers both header and data. So we need to generate the data earlier (move pktgen_finalize_skb up), and compute the checksum for UDP header + data. Fixes: c26bf4a5 ("pktgen: Add UDPCSUM flag to support UDP checksums") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Al Viro authored
commit 0a280962 upstream. X-Coverup: just ask spender Signed-off-by:
-
Al Viro authored
commit 7e0e953b upstream. use_pde()/unuse_pde() in ->follow_link()/->put_link() resp. Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
commit 045c47ca upstream. When reading blkio.throttle.io_serviced in a recently created blkio cgroup, it's possible to race against the creation of a throttle policy, which delays the allocation of stats_cpu. Like other functions in the throttle code, just checking for a NULL stats_cpu prevents the following oops caused by that race. [ 1117.285199] Unable to handle kernel paging request for data at address 0x7fb4d0020 [ 1117.285252] Faulting instruction address: 0xc0000000003efa2c [ 1137.733921] Oops: Kernel access of bad area, sig: 11 [#1] [ 1137.733945] SMP NR_CPUS=2048 NUMA PowerNV [ 1137.734025] Modules linked in: bridge stp llc kvm_hv kvm binfmt_misc autofs4 [ 1137.734102] CPU: 3 PID: 5302 Comm: blkcgroup Not tainted 3.19.0 #5 [ 1137.734132] task: c000000f1d188b00 ti: c000000f1d210000 task.ti: c000000f1d210000 [ 1137.734167] NIP: c0000000003efa2c LR: c0000000003ef9f0 CTR: c0000000003ef980 [ 1137.734202] REGS: c000000f1d213500 TRAP: 0300 Not tainted (3.19.0) [ 1137.734230] MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 42008884 XER: 20000000 [ 1137.734325] CFAR: 0000000000008458 DAR: 00000007fb4d0020 DSISR: 40000000 SOFTE: 0 GPR00: c0000000003ed3a0 c000000f1d213780 c000000000c59538 0000000000000000 GPR04: 0000000000000800 0000000000000000 0000000000000000 0000000000000000 GPR08: ffffffffffffffff 00000007fb4d0020 00000007fb4d0000 c000000000780808 GPR12: 0000000022000888 c00000000fdc0d80 0000000000000000 0000000000000000 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 000001003e120200 c000000f1d5b0cc0 0000000000000200 0000000000000000 GPR24: 0000000000000001 c000000000c269e0 0000000000000020 c000000f1d5b0c80 GPR28: c000000000ca3a08 c000000000ca3dec c000000f1c667e00 c000000f1d213850 [ 1137.734886] NIP [c0000000003efa2c] .tg_prfill_cpu_rwstat+0xac/0x180 [ 1137.734915] LR [c0000000003ef9f0] .tg_prfill_cpu_rwstat+0x70/0x180 [ 1137.734943] Call Trace: [ 1137.734952] [c000000f1d213780] [d000000005560520] 0xd000000005560520 (unreliable) [ 1137.734996] [c000000f1d2138a0] [c0000000003ed3a0] .blkcg_print_blkgs+0xe0/0x1a0 [ 1137.735039] [c000000f1d213960] [c0000000003efb50] .tg_print_cpu_rwstat+0x50/0x70 [ 1137.735082] [c000000f1d2139e0] [c000000000104b48] .cgroup_seqfile_show+0x58/0x150 [ 1137.735125] [c000000f1d213a70] [c0000000002749dc] .kernfs_seq_show+0x3c/0x50 [ 1137.735161] [c000000f1d213ae0] [c000000000218630] .seq_read+0xe0/0x510 [ 1137.735197] [c000000f1d213bd0] [c000000000275b04] .kernfs_fop_read+0x164/0x200 [ 1137.735240] [c000000f1d213c80] [c0000000001eb8e0] .__vfs_read+0x30/0x80 [ 1137.735276] [c000000f1d213cf0] [c0000000001eb9c4] .vfs_read+0x94/0x1b0 [ 1137.735312] [c000000f1d213d90] [c0000000001ebb38] .SyS_read+0x58/0x100 [ 1137.735349] [c000000f1d213e30] [c000000000009218] syscall_exit+0x0/0x98 [ 1137.735383] Instruction dump: [ 1137.735405] 7c6307b4 7f891800 409d00b8 60000000 60420000 3d420004 392a63b0 786a1f24 [ 1137.735471] 7d49502a e93e01c8 7d495214 7d2ad214 <7cead02a> e9090008 e9490010 e9290018 And here is one code that allows to easily reproduce this, although this has first been found by running docker. void run(pid_t pid) { int n; int status; int fd; char *buffer; buffer = memalign(BUFFER_ALIGN, BUFFER_SIZE); n = snprintf(buffer, BUFFER_SIZE, "%d\n", pid); fd = open(CGPATH "/test/tasks", O_WRONLY); write(fd, buffer, n); close(fd); if (fork() > 0) { fd = open("/dev/sda", O_RDONLY | O_DIRECT); read(fd, buffer, 512); close(fd); wait(&status); } else { fd = open(CGPATH "/test/blkio.throttle.io_serviced", O_RDONLY); n = read(fd, buffer, BUFFER_SIZE); close(fd); } free(buffer); exit(0); } void test(void) { int status; mkdir(CGPATH "/test", 0666); if (fork() > 0) wait(&status); else run(getpid()); rmdir(CGPATH "/test"); } int main(int argc, char **argv) { int i; for (i = 0; i < NR_TESTS; i++) test(); return 0; } Reported-by:
Ricardo Marin Matinata <rmm@br.ibm.com> Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Jay Lan authored
commit 14675592 upstream. The output of KDB 'summary' command should report MemTotal, MemFree and Buffers output in kB. Current codes report in unit of pages. A define of K(x) as is defined in the code, but not used. This patch would apply the define to convert the values to kB. Please include me on Cc on replies. I do not subscribe to linux-kernel. Signed-off-by:
Jay Lan <jlan@sgi.com> Signed-off-by:
Jason Wessel <jason.wessel@windriver.com> Signed-off-by:
-
James Hogan authored
[ Upstream commit 3ce465e0 ] Export the _save_fp asm function used by the lose_fpu(1) macro to GPL modules so that KVM can make use of it when it is built as a module. This fixes the following build error when CONFIG_KVM=m due to commit f798217d ("KVM: MIPS: Don't leak FPU/DSP to guest"): ERROR: "_save_fp" [arch/mips/kvm/kvm.ko] undefined! Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> [james.hogan@imgtec.com: Only export when CPU_R4K_FPU=y prior to v3.16, so as not to break the Octeon build which excludes FPU support. KVM depends on MIPS32r2 anyway.] Signed-off-by:
-
Ilya Dryomov authored
commit 7eb71e03 upstream. It turns out it's possible to get __remove_osd() called twice on the same OSD. That doesn't sit well with rb_erase() - depending on the shape of the tree we can get a NULL dereference, a soft lockup or a random crash at some point in the future as we end up touching freed memory. One scenario that I was able to reproduce is as follows: <osd3 is idle, on the osd lru list> <con reset - osd3> con_fault_finish() osd_reset() <osdmap - osd3 down> ceph_osdc_handle_map() <takes map_sem> kick_requests() <takes request_mutex> reset_changed_osds() __reset_osd() __remove_osd() <releases request_mutex> <releases map_sem> <takes map_sem> <takes request_mutex> __kick_osd_requests() __reset_osd() __remove_osd() <-- !!! A case can be made that osd refcounting is imperfect and reworking it would be a proper resolution, but for now Sage and I decided to fix this by adding a safe guard around __remove_osd(). Fixes: http://tracker.ceph.com/issues/8087 Cc: Sage Weil <sage@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Sage Weil <sage@redhat.com> Reviewed-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Ilya Dryomov authored
commit cc9f1f51 upstream. No reason to use BUG_ON for osd request list assertions. Signed-off-by:
Ilya Dryomov <idryomov@redhat.com> Reviewed-by:
-
Ilya Dryomov authored
commit 7c6e6fc5 upstream. It is important that both regular and lingering requests lists are empty when the OSD is removed. Signed-off-by:
Ilya Dryomov <ilya.dryomov@inktank.com> Reviewed-by:
-
Arnd Bergmann authored
commit 61882b63 upstream. The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register are marked init but are called from a context that might be run after the __init sections are discarded, as the compiler points out: WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init() WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register() This removes the __init markings. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Mikulas Patocka authored
commit 22aa66a3 upstream. When the snapshot target is unloaded, snapshot_dtr() waits until pending_exceptions_count drops to zero. Then, it destroys the snapshot. Therefore, the function that decrements pending_exceptions_count should not touch the snapshot structure after the decrement. pending_complete() calls free_pending_exception(), which decrements pending_exceptions_count, and then it performs up_write(&s->lock) and it calls retry_origin_bios() which dereferences s->origin. These two memory accesses to the fields of the snapshot may touch the dm_snapshot struture after it is freed. This patch moves the call to free_pending_exception() to the end of pending_complete(), so that the snapshot will not be destroyed while pending_complete() is in progress. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
commit 2bec1f4a upstream. The function dm_get_md finds a device mapper device with a given dev_t, increases the reference count and returns the pointer. dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the device, tests that the device doesn't have DMF_DELETING or DMF_FREEING flag, drops _minor_lock and returns pointer to the device. dm_get_md then calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag, otherwise it increments the reference count. There is a possible race condition - after dm_find_md exits and before dm_get is called, there are no locks held, so the device may disappear or DMF_FREEING flag may be set, which results in BUG. To fix this bug, we need to call dm_get while we hold _minor_lock. This patch renames dm_find_md to dm_get_md and changes it so that it calls dm_get while holding the lock. Signed-off-by:
-
NeilBrown authored
commit 26ac1073 upstream. Commit a7854487: md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write. Causes an RCW cycle to be forced even when the array is degraded. A degraded array cannot support RCW as that requires reading all data blocks, and one may be missing. Forcing an RCW when it is not possible causes a live-lock and the code spins, repeatedly deciding to do something that cannot succeed. So change the condition to only force RCW on non-degraded arrays. Reported-by:
Manibalan P <pmanibalan@amiindia.co.in> Bisected-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Tested-by:
-
Mitko Haralanov authored
commit 18c0b82a upstream. This changeset removes all the code that allows the driver to write to the EEPROM and update the recorded error counters and power on hours. These two stats are unused and writing them exposes a timing risk which could leave the EEPROM in a bad state preventing further normal operation of the HCA. Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Tony Battersby authored
commit 3b524a68 upstream. Fix SCSI generic read() incorrectly returning success after detecting an error. Signed-off-by:
Tony Battersby <tonyb@cybernetics.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Minh Duc Tran authored
fixed invalid assignment of 64bit mask to host dma_boundary for scatter gather segment boundary limit. commit f76a610a upstream. In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141 Assert is seen with AMD cpu whenever calling pci_alloc_consistent. [ 29.406183] ------------[ cut here ]------------ [ 29.410505] kernel BUG at lib/iommu-helper.c:13! Signed-off-by:
Minh Tran <minh.tran@emulex.com> Fixes: 6733b39aSigned-off-by:
-
honclo authored
commit eb71f8a5 upstream. The tpm_ibmvtpm module is affected by an unaligned access problem. ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is enabled in Power partition, which supports both little endian and big endian modes. We added little endian support to fix this problem: 1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS. 2) added be16_to_cpu and be32_to_cpu calls to make sure data received is in LE format on a LE OS. Signed-off-by:
Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Signed-off-by:
Joy Latten <jmlatten@linux.vnet.ibm.com> [phuewe: manually applied the patch :( ] Reviewed-by:
Ashley Lai <ashley@ahsleylai.com> Signed-off-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
-
Filipe Manana authored
commit 1a4bcf47 upstream. We have a scenario where after the fsync log replay we can lose file data that had been previously fsync'ed if we added an hard link for our inode and after that we sync'ed the fsync log (for example by fsync'ing some other file or directory). This is because when adding an hard link we updated the inode item in the log tree with an i_size value of 0. At that point the new inode item was in memory only and a subsequent fsync log replay would not make us lose the file data. However if after adding the hard link we sync the log tree to disk, by fsync'ing some other file or directory for example, we ended up losing the file data after log replay, because the inode item in the persisted log tree had an an i_size of zero. This is easy to reproduce, and the following excerpt from my test for xfstests shows this: _scratch_mkfs >> $seqres.full 2>&1 _init_flakey _mount_flakey # Create one file with data and fsync it. # This made the btrfs fsync log persist the data and the inode metadata with # a correct inode->i_size (4096 bytes). $XFS_IO_PROG -f -c "pwrite -S 0xaa -b 4K 0 4K" -c "fsync" \ $SCRATCH_MNT/foo | _filter_xfs_io # Now add one hard link to our file. This made the btrfs code update the fsync # log, in memory only, with an inode metadata having a size of 0. ln $SCRATCH_MNT/foo $SCRATCH_MNT/foo_link # Now force persistence of the fsync log to disk, for example, by fsyncing some # other file. touch $SCRATCH_MNT/bar $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/bar # Before a power loss or crash, we could read the 4Kb of data from our file as # expected. echo "File content before:" od -t x1 $SCRATCH_MNT/foo # Simulate a crash/power loss. _load_flakey_table $FLAKEY_DROP_WRITES _unmount_flakey _load_flakey_table $FLAKEY_ALLOW_WRITES _mount_flakey # After the fsync log replay, because the fsync log had a value of 0 for our # inode's i_size, we couldn't read anymore the 4Kb of data that we previously # wrote and fsync'ed. The size of the file became 0 after the fsync log replay. echo "File content after:" od -t x1 $SCRATCH_MNT/foo Another alternative test, that doesn't need to fsync an inode in the same transaction it was created, is: _scratch_mkfs >> $seqres.full 2>&1 _init_flakey _mount_flakey # Create our test file with some data. $XFS_IO_PROG -f -c "pwrite -S 0xaa -b 8K 0 8K" \ $SCRATCH_MNT/foo | _filter_xfs_io # Make sure the file is durably persisted. sync # Append some data to our file, to increase its size. $XFS_IO_PROG -f -c "pwrite -S 0xcc -b 4K 8K 4K" \ $SCRATCH_MNT/foo | _filter_xfs_io # Fsync the file, so from this point on if a crash/power failure happens, our # new data is guaranteed to be there next time the fs is mounted. $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo # Add one hard link to our file. This made btrfs write into the in memory fsync # log a special inode with generation 0 and an i_size of 0 too. Note that this # didn't update the inode in the fsync log on disk. ln $SCRATCH_MNT/foo $SCRATCH_MNT/foo_link # Now make sure the in memory fsync log is durably persisted. # Creating and fsync'ing another file will do it. touch $SCRATCH_MNT/bar $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/bar # As expected, before the crash/power failure, we should be able to read the # 12Kb of file data. echo "File content before:" od -t x1 $SCRATCH_MNT/foo # Simulate a crash/power loss. _load_flakey_table $FLAKEY_DROP_WRITES _unmount_flakey _load_flakey_table $FLAKEY_ALLOW_WRITES _mount_flakey # After mounting the fs again, the fsync log was replayed. # The btrfs fsync log replay code didn't update the i_size of the persisted # inode because the inode item in the log had a special generation with a # value of 0 (and it couldn't know the correct i_size, since that inode item # had a 0 i_size too). This made the last 4Kb of file data inaccessible and # effectively lost. echo "File content after:" od -t x1 $SCRATCH_MNT/foo This isn't a new issue/regression. This problem has been around since the log tree code was added in 2008: Btrfs: Add a write ahead tree log to optimize synchronous operations (commit e02119d5) Test cases for xfstests follow soon. Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
Chris Mason <clm@fb.com> [ kamal: backport to 3.13-stable: context ] Signed-off-by:
-
