- 26 Jun, 2005 28 commits
-
-
Andrew Morton authored
drivers/net/tulip/dmfe.c: In function `dmfe_parse_srom': drivers/net/tulip/dmfe.c:1805: warning: passing arg 1 of `__le16_to_cpup' from incompatible pointer type drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type This is basically a guess: Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by:Andrew Morton <akpm@osdl.org>
-
Adrian Bunk authored
The 8129/8130 support is a sub-option that is not visible if the user hasn't enabled the 8139 support. Let's make it a bit easier for users to find the driver for their nic. Signed-off-by:Adrian Bunk <bunk@stusta.de>
-
Nishanth Aravamudan authored
Use msleep_interruptible() instead of schedule_timeout() to guarantee the task delays as expected.
-
Adrian Bunk authored
This patch removes some obviously dead code found by the Coverity checker. Signed-off-by: -
Adrian Bunk authored
This patch fixes the LITTLE_ENDIAN #define and a function prototype. Signed-off-by: -
Adrian Bunk authored
This patch contains the follwing cleanups: - make needlessly global code static - remove obsolete Emacs settings Signed-off-by: -
Andreas Mohr authored
During some performance diagnostics I stumbled on this slightly wasteful code in pcnet_cs.c which I made the patch included at the bottom for (two minor comment fixes included). Improvement: instead of *always* calculating lea 0x2c0(%edx),%ebx and then additionally doing the mov %edx,0xc0(%ebx) addition *if we need it*, we now do the *whole* calculation of mov %edx,0x380(%ebx) *only* if we need it. This even manages to save us a whole 16-byte alignment buffer loss in this compilation case. Result: slightly improves IRQ handler performance in both shared and non-shared IRQ case, which should make my rusty P3/700 a slight bit happier. Thank you for your support, Andreas Mohr old asm result (using gcc 3.3.5): 000015a0 <ei_irq_wrapper>: 15a0: 55 push %ebp 15a1: 89 e5 mov %esp,%ebp 15a3: 53 push %ebx 15a4: 8d 9a c0 02 00 00 lea 0x2c0(%edx),%ebx 15aa: e8 fc ff ff ff call 15ab <ei_irq_wrapper+0xb> 15af: 83 f8 01 cmp $0x1,%eax 15b2: 74 03 je 15b7 <ei_irq_wrapper+0x17> 15b4: 5b pop %ebx 15b5: 5d pop %ebp 15b6: c3 ret 15b7: 31 d2 xor %edx,%edx 15b9: 89 93 c0 00 00 00 mov %edx,0xc0(%ebx) 15bf: eb f3 jmp 15b4 <ei_irq_wrapper+0x14> 15c1: eb 0d jmp 15d0 <ei_watchdog> 15c3: 90 nop 15c4: 90 nop 15c5: 90 nop 15c6: 90 nop 15c7: 90 nop 15c8: 90 nop 15c9: 90 nop 15ca: 90 nop 15cb: 90 nop 15cc: 90 nop 15cd: 90 nop 15ce: 90 nop 15cf: 90 nop 000015d0 <ei_watchdog>: new asm result: 000015a0 <ei_irq_wrapper>: 15a0: 55 push %ebp 15a1: 89 e5 mov %esp,%ebp 15a3: 53 push %ebx 15a4: 89 d3 mov %edx,%ebx 15a6: e8 fc ff ff ff call 15a7 <ei_irq_wrapper+0x7> 15ab: 83 f8 01 cmp $0x1,%eax 15ae: 74 03 je 15b3 <ei_irq_wrapper+0x13> 15b0: 5b pop %ebx 15b1: 5d pop %ebp 15b2: c3 ret 15b3: 31 d2 xor %edx,%edx 15b5: 89 93 80 03 00 00 mov %edx,0x380(%ebx) 15bb: eb f3 jmp 15b0 <ei_irq_wrapper+0x10> 15bd: 8d 76 00 lea 0x0(%esi),%esi 000015c0 <ei_watchdog>: Signed-off-by: -
Domen Puncer authored
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling pci_set_dma_mask() or pci_set_consistent_dma_mask() This patch includes dma-mapping.h explicitly because it caused errors on some architectures otherwise. See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details Signed-off-by:Tobias Klauser <tklauser@nuerscht.ch> Signed-off-by:
Domen Puncer <domen@coderock.org>
-
Magnus Damm authored
Make sure the code compiles with and without ARLAN_ENTRY_EXIT_DEBUGGING. Only provide parameter descriptions when parameters are defined. Remove "arlan_"-prefix to shape up built-in parameter names: arlan.arlan_debug -> arlan.debug arlan.arlan_EEPROM_bad -> arlan.EEPROM_bad arlan.arlan_entry_and_exit_debug -> arlan.entry_and_exit_debug arlan.arlan_entry_debug -> arlan.entry_debug arlan.arlan_exit_debug -> arlan.exit_debug Signed-off-by:Magnus Damm <damm@opensource.se>
-
Tobias Klauser authored
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom macros. This patch includes dma-mapping.h explicitly because it caused errors on some architectures otherwise. See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details Signed-off-by:
-
Jeff Garzik authored
-
Jeff Garzik authored
-
Stephen Hemminger authored
The spin loop in 8139cp is limited to 100 iterations when pulling hardware stats. There is no allowance for processor speed so on a fast machine, the stats may not be available that fast. Also, if the board doesn't return soon enough make sure turn the address back off to prevent later updates when memory has gone away.
-
Kumar Gala authored
This patch updates the name identifier to list both of the Marvell PHYs that are supported. Signed-off-by:Kumar Gala <kumar.gala@freescale.com>
-
Jay Vosburgh authored
Add support for alternate slave selection algorithms to bonding balance-xor and 802.3ad modes. Default mode (what we have now: xor of MAC addresses) is "layer2", new choice is "layer3+4", using IP and port information for hashing to select peer. Originally submitted by Jason Gabler for balance-xor mode; modified by Jay Vosburgh to additionally support 802.3ad mode. Jason's original comment is as follows: The attached patch to the Linux Etherchannel Bonding driver modifies the driver's "balance-xor" mode as follows: - alternate hashing policy support for mode 2 * Added kernel parameter "xmit_policy" to allow the specification of different hashing policies for mode 2. The original mode 2 policy is the default, now found in xmit_hash_policy_layer2(). * Added xmit_hash_policy_layer34() This patch was inspired by hashing policies implemented by Cisco, Foundry and IBM, which are explained in Foundry documentation found at: http://www.foundrynet.com/services/documentation/sribcg/Trunking.html#112750Signed-off-by:Jason Gabler <jygabler@lbl.gov> Signed-off-by:
Jay Vosburgh <fubar@us.ibm.com>
-
Jay Vosburgh authored
Add support for generating gratuitous ARPs in bonding active-backup mode when failovers occur. Includes support for VLAN tagging the ARPs as needed. Signed-off-by: -
Ralf Baechle authored
-
Jeff Garzik authored
-
-
-
Kumar Gala authored
The pending registers for IRQ1-IRQ7 were pointing to the interrupt pending register instead of the external one. Signed-off-by:
Tony Li <Tony.Li@freescale.com> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Adrian Bunk authored
Since the Trivial Patch Monkey is mentioned both in steps 4. and 5., I removed it from step4 (Select e-mail destination), since it should go under 'Select your CC list'. Signed-off-by:
Cosmin Nicolaescu <cos@camelot.homelinux.com> Signed-off-by:
-
Andrew Morton authored
Another swsusp fixup. Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
Andrew Morton authored
Missed conversion in the swsusp cleanup. Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
Dave Airlie authored
After the previous fix in 2.6.12, this patch should properly fix the radeon IRQ handling code. From: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:Dave Airlie <airlied@linux.ie>
-
Linus Torvalds authored
The parentheses were missing. Noted by Pavel Machek.
-
Linus Torvalds authored
-
Christoph Lameter authored
1. Establish a simple API for process freezing defined in linux/include/sched.h: frozen(process) Check for frozen process freezing(process) Check if a process is being frozen freeze(process) Tell a process to freeze (go to refrigerator) thaw_process(process) Restart process frozen_process(process) Process is frozen now 2. Remove all references to PF_FREEZE and PF_FROZEN from all kernel sources except sched.h 3. Fix numerous locations where try_to_freeze is manually done by a driver 4. Remove the argument that is no longer necessary from two function calls. 5. Some whitespace cleanup 6. Clear potential race in refrigerator (provides an open window of PF_FREEZE cleared before setting PF_FROZEN, recalc_sigpending does not check PF_FROZEN). This patch does not address the problem of freeze_processes() violating the rule that a task may only modify its own flags by setting PF_FREEZE. This is not clean in an SMP environment. freeze(process) is therefore not SMP safe! Signed-off-by:
Christoph Lameter <christoph@lameter.com> Signed-off-by:
-
- 25 Jun, 2005 12 commits
-
-
Adrian Bunk authored
Since kernel 2.6.3 the Kconfig text explicitely stated this driver was obsolete. (trolling for IBMers) Signed-off-by:
-
Domen Puncer authored
Make code more readable with list_for_each_entry_safe. Signed-off-by:
Maximilian Attems <janitor@sternwelten.at> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Adrian Bunk authored
There's no need for a function that only calls udelay. Signed-off-by:
-
Adrian Bunk authored
Signed-off-by:
-
Alexey Dobriyan authored
Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Nishanth Aravamudan authored
Use msleep_interruptible() instead of schedule_timeout() in send_break() to guarantee the task delays as expected. Change @duration's units to milliseconds, and modify arguments in callers appropriately. Signed-off-by:
Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by:
-
Nishanth Aravamudan authored
Use msleep_interruptible() instead of schedule_timeout() in send_break() to guarantee the task delays as expected. Change @duration's units to milliseconds, and modify arguments in callers appropriately. Signed-off-by:
-
Tobias Klauser authored
The files wanpipe.txt and wan-router.txt in Documentation/networking contain the exact same information (diff between the two shows no document is "Linux WAN Router Utilities Package" and therefor the name wan-router.txt is more appropriate. Signed-off-by:
-
Tobias Klauser authored
wanpipe.txt and wan-router.txt in Documentation/networking contain the exact same information (diff between the two shows no Documentation/networking/00-INDEX as pointed out by Randy Dunlap. Signed-off-by:
-
Tobias Klauser authored
wanpipe.txt and wan-router.txt in Documentation/networking contain the exact same information (diff between the two shows no drivers/net/wan/Kconfig. Signed-off-by:
-
Tobias Klauser authored
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling pci_set_dma_mask() or pci_set_consistent_dma_mask() See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details Signed-off-by:
-
Tobias Klauser authored
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling pci_set_dma_mask() or pci_set_consistent_dma_mask() See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details Signed-off-by:
-
