The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.

This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.

Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.

Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not all Marvell switch chips feature a Cross-chip Port VLAN Table (PVT).

Chips with a PVT use the same implementation, so a new mv88e6xxx_ops
member won't be necessary yet. Add a "pvt" boolean member to the
mv88e6xxx_info structure and kill the obsolete MV88E6XXX_FLAGS_PVT flag.

Add a mv88e6xxx_has_pvt helper to wrap future checks of that condition.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AVOIDBLOCK flag determines the Tx confirmation queues processing
to be redirected to any available CPU when the current one is slow
in processing them. This may result in a higher Tx confirmation
interrupt count but may reduce pressure on a certain CPU that with
the previous setting would process all Tx confirmation frames.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accept the internal delay RGMII variants.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan dev currently ignores lowerdev's gso_max_size, which adversely
affects TSO performance of liquidio if it's the lowerdev.  Egress TCP
packets' skb->len often exceed liquidio's advertised gso_max_size.  This
may happen on other NIC drivers.

Fix it by assigning lowerdev's gso_max_size to that of vxlan dev.  Might as
well do likewise for gso_max_segs.

Single flow TSO throughput of liquidio as lowerdev (using iperf3):

    Before the patch:    139 Mbps
    After the patch :   8.68 Gbps
    Percent increase:  6,144 %
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_recv_ts_and_drops() unconditionally set sk->sk_stamp for
every packet, even if the SOCK_TIMESTAMP flag is not set in the
related socket.
If selinux is enabled, this cause a cache miss for every packet
since sk->sk_stamp and sk->sk_security share the same cacheline.
With this change sk_stamp is set only if the SOCK_TIMESTAMP
flag is set, and is cleared for the first packet, so that the user
perceived behavior is unchanged.

This gives up to 5% speed-up under udp-flood with small packets.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nathan Fontenot says:

====================
ibmvnic: Cleanup resource handling

In order to better manage the resources of the ibmvnic driver, this set of
patches creates a set of initialization and release routines for the
drivers resources. Additionally, some patches do some re-naming of the
affected routines so that there is a common naming scheme in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that ibmvnic_release_resources will clean up all of our resources
properly, even if they were not allocated, we can just call this
for failues in ibmvnic_open.

This patch also moves the ibmvnic_release_resources() routine up
in the file to avoid creating a forward declaration ad re-names it to
drop the ibmvnic prefix.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create an initialization and a release routine for the stats token used by
the ibmvnic driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Keeping two routines for releasing sub crqs, one for when irqs are not
initialized and one for when they are, is a bit of overkill. Merge the
two routines to a common release routine that will check for an irq
and release it if needed.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the initialization and the release of the rx pool to their own
routines, and update them to do validation.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the initialization and the release of the tx pool to their own routines,
and update them to do validation. This also adds validation to the release
of the long term buffer.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the handling of initialization and releasing the bounce buffer to their
own init and release routines.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the initialization and release routines for the crq queue so that
we validate the crq queue.

Additionally this updates the naming of the init and release routines
for the crq queue to drop the ibmvnic prefix. This matches the naming
for similar routines in the driver
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Move the "window = tp->rcv_wnd;" into the condition block without
tp->rx_opt.rcv_wscale.
Because it is unnecessary when enable wscale;

2. Use the macro ALIGN instead of two statements.
The two statements are used to make window align to 1<<wscale.
Use the ALIGN is more clearer.

3. Use the rounddown to make codes clearer.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ATU ageing time value programmed in the switch is rounded up to the
nearest multiple of its coefficient (variable depending on the model.)

Add a debug message to inform the user about the exact programmed value.

On 6352, "brctl setageing br0 18" gives "AgeTime set to 0x01 (15000 ms)"
while on 6390 we get "AgeTime set to 0x05 (18750 ms)".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The debugfs support in the ibmvnic driver is not, and never has been,
supported. Just remove it.

The work done in the debugfs code for the driver was part of the original
spec for the ibmvnic driver. The corresponding support for this from the
server side was never supported and has been dropped.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some device drivers reset their stats at down/up events, possibly
fooling bonding stats, since they operate with relative deltas.

It is nearly not possible to fix drivers, since some of them compute the
tx/rx counters based on per rx/tx queue stats, and the queues can be
reconfigured (ethtool -L) between the down/up sequence.

Lets avoid accumulating 'negative' values that render bonding stats
useless.

It is better to lose small deltas, assuming the bonding stats are
fetched at a reasonable frequency.

Fixes: 5f0c5f73 ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than assign the positive errno values to ret and then
checking if it is positive and flip the sign, just return the
errno value.

Detected by CoverityScan, CID#986649 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).

That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

ATM dwmac-rk will always set and enable it's internal delay lines.
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.

Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.

Tested only with a RK3288 based board.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit aff3d9ef ("net: stmmac: enable multiple buffers") breaks
numerous boards. while some patch exists for fixing some of it,
dwmac-sunxi is still broken with it.
Since this patch is very huge, it will be better to split it in smaller
part.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-03-29

This series contains updates to i40e and i40evf only.

Preethi changes the default driver mode of operation to descriptor
write-back for VF.

Alex cleans up and addresses several issues in the way that i40e handles
private flags.  Modifies the driver to use the length of the packet
instead of the DD status bit to determine if a new descriptor is ready
to be processed.  Refactors the driver by pulling the code responsible
for fetching the receive buffer and synchronizing DMA into a single
function.  Also pulled the code responsible for handling buffer
recycling and page counting and distributed it through several functions,
so we can commonize the bits that handle either freeing or recycling the
buffers.  Cleans up the code in preparation for us adding support for
build_skb().  Changed the way we handle the maximum frame size for the
receive path so it is more consistent with other drivers.

Paul enables XL722 to use the direct read/write method since it does not
support the AQ command to read/write the control register.

Christopher fixes a case where we miss an arq element if a new one is
added before we enable interrupts and exit the loop.

Jake cleans up a pointless goto statement.  Also cleaned up a flag that
was not being used.

Carolyn does round 2 for adding a delay to the receive queue to
accommodate the hardware needs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Parthasarathy Bhuvaragan says:

====================
tipc: add socketpair support

We add socketpair support for connection oriented sockets in
the first patch and for connection less in the second.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

for socketpairs using connectionless transport, we cache
the respective node local TIPC portid to use in subsequent
calls to send() in the socket's private data.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sockets A and B are connected back-to-back, similar to what
AF_UNIX does.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I found a bug by:

0. boot and start dhcp client
1. echo mem > /sys/power/state
2. resume back immediately
3. don't touch dhcp client to renew the lease
4. ping the gateway. No acks

Usually, after step2, the DHCP lease isn't expired, so in theory we
should resume all back. But in fact, it doesn't. It turns out
the rx mode isn't resumed correctly. This patch fixes it by adding
mvneta_set_rx_mode(dev) in the resume hook if interface is running.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

RGMII_RXID and RGMII_TX_ID share the same GMAC CTRL setting as RGMII
or RGMII_ID.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx5e-pedit 2017-03-28

This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.

The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.

One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.

Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.

The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.

The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.

Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.

Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.

I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit skips nexthops in a route if the device has been
deleted. Update lfib_nlmsg_size accordingly.
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:

- descend into drivers/net/phy/ unconditionally

- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
  which allows us not to expose the internal MDIO board info list and
  mutex, yet maintain the logic within the same file

- relocate the code that creates a MDIO device into
  drivers/net/phy/mdio_bus.c

- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
  defined (y or m)

Fixes: 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea013 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a delay to Rx queue disables to accommodate HW needs.

v2: Added missing check for disable only, additional details on the
need for the ugly delay and fixed spacing on comment.

Change-ID: I2864ca667ce5dcc2cc44f8718113b719742a46a1
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the way we handle the maximum frame size for the Rx
path.  Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount.  With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size.  This makes the behavior more
consistent with the other drivers such as igb which had similar logic.  In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.

Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode.  The legacy Rx mode is what we currently do when performing
Rx.  As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.

Change-ID: I0342998849bbb31351cce05f6e182c99174e7751
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to clean up the code in preparation for us adding
support for build_skb.  Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.

Specifically with this change we split out the code for adding a page to an
exiting skb.

Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions.  This allows us
to commonize the bits that handle either freeing or recycling the buffers.

As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer.  It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.

Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.

The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer.  We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.

Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.

Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>