All other loops over sh_pfc_soc_info.data_regs[] use
pinmux_data_reg.regwidth as the sentinel, which is safer as zero is
never a valid regwidth value (reg could be zero if we start using it to
store an offset).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As register and field widths and offsets are in the range 1..32, use
unsigned int (mostly replacing unsigned long) to store them in local
variables and for passing them around.

Move to one variable per line, move variables to the beginning of the
block where they are used, and drop superfluous initializations while we
are at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Register and field widths are in the range 1..32. Storing them in the
pinctrl data in (arrays of) unsigned long wastes space.

This decreases the size of a (32-bit) shmobile_defconfig kernel
supporting 7 SoCs by 26460 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

KERNCZ GPIO is a new IP from AMD. it can be implemented in both x86 and ARM.
Current driver patch only support GPIO in x86.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
[Moved back to <linux/gpio.h> header]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The callback function signature has changed in commit a5818a8b (pinctrl:
get_group_pins() const fixes)

Fixes: a5818a8b ('pinctrl: get_group_pins() const fixes')
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The alive pin controller on exynos7 does not support external gpio
interrupts. Hence, remove the eint_gpio_init call-back for it. This
fixes the following error message seen during exynos7 boot-up:
"samsung-pinctrl 10580000.pinctrl: irq number not available"
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the initial support of the Broadcom Cygnus GPIO/PINCONF driver
that supports all 3 GPIO controllers on Cygnus including the ASIU GPIO
controller, the chipCommonG GPIO controller, and the always-on GPIO
controller. Basic PINCONF configurations such as bias pull up/down, and
drive strength are also supported in this driver.

Pins from the ASIU GPIO controller can be individually muxed to GPIO
function, through interaction with the Cygnus IOMUX controller
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Document the GPIO/PINCONF device tree binding for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make the example code consistent wrt local function and struct definitions.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This API has changed in commit 6e5e959d (pinctrl: API changes to support
multiple states per device).

Fixes: 6e5e959d ('pinctrl: API changes to support multiple states per device')
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit 03e9f0ca (pinctrl: clean up after enable refactoring) updated the
documentation to remove mention of disable(), and rename enable() to set_mux().
One in-text mention was forgotten. Fix this.

Fixes: 03e9f0ca ('pinctrl: clean up after enable refactoring')
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Due to pinconf_generic_parse_dt_config() API changes in pinctrl
devel branch, add one parameter to fix build error.

Also fix warning:
drivers/pinctrl/mediatek/pinctrl-mtk-common.c:718:3: warning:
too many arguments for format [-Wformat-extra-args]
      dev_err(&pdev->dev, "only support pins-are-numbered format\n", ret);
      ^

by removing extra parameter when calling dev_err in mtk_pctrl_init.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

MTK EINT does not support generating interrupt on both edges.
Emulate this by changing edge polarity while enable irq,
set types and interrupt handling. This follows an example of
drivers/gpio/gpio-mxc.c.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add mt8173 support using mediatek common pinctrl driver.
MT8173 have a different ies_smt setting register than mt8135,
so adding this support to common code.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

MTK SoC support external interrupt(EINT) from most SoC pins.
Add EINT support to pinctrl driver.
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.

The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.

This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add devicetree bindings for Mediatek SoC pinctrl driver.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As PFC registers are either 8, 16, or 32 bits wide, use u32 (mostly
replacing unsigned long) to store (parts of) register values and masks.

Switch the shadow register operations from {set,clear}_bit() to plain C
bit operations, as the former can operate on long data only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the initial driver support for the Broadcom Cygnus IOMUX
controller. The Cygnus IOMUX controller supports group based mux
configuration but allows certain pins to be muxed to GPIO individually
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Device tree binding documentation for Broadcom Cygnus IOMUX driver
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Consolidate Broadcom pinctrl drivers into drivers/pinctrl/bcm/*
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit 3dac1918 ("pinctrl: imx: detect uninitialized pins") needs
the values in struct imx_pin_reg to be -1. This has been done in a
rather unorthodox way by setting the memory to 0xff using memset...
Use a proper for loop to initialize the whole array with -1.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This enables support of 'input-enable' pinconf generic property in
the pinctrl driver.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the pinctrl driver to use the generic pinconf
interface. Mainly it gives us a way to use debugfs to dump
group configurations.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There is no code ender the 'err' label. Just return the error code directly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

struct pinctrl_desc does not contain the maxpin member since commit 0d2006bb
(pinctrl: remove unnecessary max pin number).

Fixes: 0d2006bb ('pinctrl: remove unnecessary max pin number')
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix typo, "flaged" -> "flagged"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).

Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Both nvidia,io-hv and nvidia,rcv-sel represent the fact that a particular
pin's IO buffers are configured to accept "high voltage" input signals.
The TRM for different chips names the register field rcv-sel on older
SoCs and io_hv on newer SoCs. Add the new naming option into the pinctrl
driver so that DT files can use naming consistent with the TRM.

This new property name will be documented in the patch that adds support
for the new SoC.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some of the pinmux configuration bits that exist in "drive group"
registers in Tegra30..Tegra124 move to the "pinmux" registers on future
chips. Add a flag to support this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Various non-semantic tweaks and layout/consistency fixes for existing
Tegra pinctrl drivers.

Move the definition of DRV_PINGROUP_REG() before the definition of
PINGROUP() so that a future SoC driver can invoke the former from the
latter.

PINGROUP_BIT_Y(n) is just n, so replace it with n.

Re-wrap the parameters to *PINGROUP().

Keep various enums sorted in the Tegra124 driver.

Various white-space consistency fixes.

These changes aim to update existing drivers to be consistent with future
SoC drivers. While we could ignore these tweaks to the existing drivers,
I'd like to keep everything as consistent as possible for easy comparison.
Besides, I auto-generate the drivers, and maintaining special-cases to
keep the differences in place is annoying.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This commit adds the Device Tree binding documentation to describe the
pin-muxing controller of the Marvell Armada 39x processors. Two
variants are supported for the moment: the 88F6920 (Armada 390) and
88F6928 (Armada 398).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make of_device_id array const.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

After the last user of the in_pd/in_pu bias parameters of the _PCRH()
macro was removed in commit 80da8e02 ("sh-pfc: r8a7740: Add bias
(pull-up/down) pinconf support"), bias parameters are supposed to be
configured using the generic pinctl mechanism, which calls the
.set_bias() method.

However, the PORTCR() macro still represents the control register as
consisting of two 4-bit fields. Hence the bias configuration in the
uppermost 2 bits is always overwritten with zeroes when a pin is
configured for GPIO, disabling any previously configured bias.

Use the variable config register macro instead, to represent the
register as having 4 fields, and to make sure only the input/output
control and function fields are touched.

This affects R-Mobile APE6 (r8a73a4), R-Mobile A1 (r8a7740), SH-Mobile
AP4 (sh7372), and SH-Mobile AG5 (sh73a0).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The r8a7791 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds driver data for Exynos5433 SoC. Exynos5433 includes 228 multi-
functional input/output port pins and 135 memory port pins. There are 41 general
port groups and 2 memory port groups.

Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This commit adds a new pinctrl driver for the Marvell Armada 39x
family of processors, which hooks into the existing infrastructure to
support pin-muxing on Marvell EBU processors. Two variants of the
Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
398), which have a few differences in the available functions for
certain pins.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

.. after extensive statistical analysis of my G+ polling, I've come to
the inescapable conclusion that internet polls are bad.

Big surprise.

But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38%
margin, in a poll that people weren't even supposed to participate in.
Who can argue with solid numbers like that? 5,796 votes from people who
can't even follow the most basic directions?

In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%,
but with a total of 29,110 votes right now.

Now, arguably, that vote spread is only about 3,200 votes, which is less
than the almost six thousand votes that the "please ignore" poll got, so
it could be considered noise.

But hey, I asked, so I'll honor the votes.