- 15 Jun, 2016 40 commits
-
-
Anton Blanchard authored
commit b4c11211 upstream. In create_zero_mask() we have: addi %1,%2,-1 andc %1,%1,%2 popcntd %0,%1 using the "r" constraint for %2. r0 is a valid register in the "r" set, but addi X,r0,X turns it into an li: li r7,-1 andc r7,r7,r0 popcntd r4,r7 Fix this by using the "b" constraint, for which r0 is not a valid register. This was found with a kernel build using gcc trunk, narrowed down to when -frename-registers was enabled at -O2. It is just luck however that we aren't seeing this on older toolchains. Thanks to Segher for working with me to find this issue. Fixes: d0cebfa6 ("powerpc: word-at-a-time optimization for 64-bit Little Endian") Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> [bwh: Backported to 3.16: same issue exists with a different variable in find_zero()] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
K. Y. Srinivasan authored
commit 1db488d1 upstream. On the consumer side, we have interrupt driven flow management of the producer. It is sufficient to base the signaling decision on the amount of space that is available to write after the read is complete. The current code samples the previous available space and uses this in making the signaling decision. This state can be stale and is unnecessary. Since the state can be stale, we end up not signaling the host (when we should) and this can result in a hang. Fix this problem by removing the unnecessary check. I would like to thank Arseney Romanenko <arseneyr@microsoft.com> for pointing out this issue. Also, issue a full memory barrier before making the signaling descision to correctly deal with potential reordering of the write (read index) followed by the read of pending_sz. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Tested-by:
Dexuan Cui <decui@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Christopher Oo authored
commit a5cca686 upstream. Fixes a bug where previously hv_ringbuffer_read would pass in the old number of bytes available to read instead of the expected old read index when calculating when to signal to the host that the ringbuffer is empty. Since the previous write size is already saved, also changes the hv_need_to_signal_on_read to use the previously read value rather than recalculating it. Signed-off-by:
Christopher Oo <t-chriso@microsoft.com> Signed-off-by:
-
Al Viro authored
commit 10c64cea upstream. * if we have a hashed negative dentry and either CREAT|EXCL on r/o filesystem, or CREAT|TRUNC on r/o filesystem, or CREAT|EXCL with failing may_o_create(), we should fail with EROFS or the error may_o_create() has returned, but not ENOENT. Which is what the current code ends up returning. * if we have CREAT|TRUNC hitting a regular file on a read-only filesystem, we can't fail with EROFS here. At the very least, not until we'd done follow_managed() - we might have a writable file (or a device, for that matter) bound on top of that one. Moreover, the code downstream will see that O_TRUNC and attempt to grab the write access (*after* following possible mount), so if we really should fail with EROFS, it will happen. No need to do that inside atomic_open(). The real logics is much simpler than what the current code is trying to do - if we decided to go for simple lookup, ended up with a negative dentry *and* had create_error set, fail with create_error. No matter whether we'd got that negative dentry from lookup_real() or had found it in dcache. Acked-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [bwh: Backported to 3.16: deleted code was slightly different] Signed-off-by:
-
Tony Luck authored
commit c4fc1956 upstream. Both of these drivers can return NOTIFY_BAD, but this terminates processing other callbacks that were registered later on the chain. Since the driver did nothing to log the error it seems wrong to prevent other interested parties from seeing it. E.g. neither of them had even bothered to check the type of the error to see if it was a memory error before the return NOTIFY_BAD. Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Aristeu Rozanski <aris@redhat.com> Acked-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/72937355dd92318d2630979666063f8a2853495b.1461864507.git.tony.luck@intel.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Sven Eckelmann authored
commit a33d970d upstream. The batadv_tt_local_entry was specific to a batadv_softif_vlan and held an implicit reference to it. But this reference was never stored in form of a pointer in the tt_local_entry itself. Instead batadv_tt_local_remove, batadv_tt_local_table_free and batadv_tt_local_purge_pending_clients depend on a consistent state of bat_priv->softif_vlan_list and that batadv_softif_vlan_get always returns the batadv_softif_vlan object which it has a reference for. But batadv_softif_vlan_get cannot guarantee that because it is working only with rcu_read_lock on this list. It can therefore happen that an vid is in this list twice or that batadv_softif_vlan_get cannot find the batadv_softif_vlan for an vid due to some other list operations taking place at the same time. Instead add a batadv_softif_vlan pointer directly in batadv_tt_local_entry which will be used for the reference counter decremented on release of batadv_tt_local_entry. Fixes: 35df3b29 ("batman-adv: fix TT VLAN inconsistency on VLAN re-add") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Acked-by:
Antonio Quartulli <a@unstable.cc> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
-
Antonio Quartulli authored
commit 2871734e upstream. Now that DAT is VLAN aware, it must use the VID when computing the DHT address of the candidate nodes where an entry is going to be stored/retrieved. Fixes: be1db4f6 ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by:
-
Sven Eckelmann authored
commit b7fe3d4f upstream. batadv_dat_select_candidates provides an u32 to batadv_hash_dat but it needs a batadv_dat_entry with at least ip and vid filled in. Fixes: 3e26722bc9f2 ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by:
Sven Eckelmann <sven@open-mesh.com> Acked-by:
Antonio Quartulli <antonio@meshcoding.com> Signed-off-by:
-
Konstantin Khlebnikov authored
commit 3486b85a upstream. Khugepaged detects own VMAs by checking vm_file and vm_ops but this way it cannot distinguish private /dev/zero mappings from other special mappings like /dev/hpet which has no vm_ops and popultes PTEs in mmap. This fixes false-positive VM_BUG_ON and prevents installing THP where they are not expected. Link: http://lkml.kernel.org/r/CACT4Y+ZmuZMV5CjSFOeXviwQdABAgT7T+StKfTqan9YDtgEi5g@mail.gmail.com Fixes: 78f11a25 ("mm: thp: fix /dev/zero MAP_PRIVATE and vm_flags cleanups") Signed-off-by:
Konstantin Khlebnikov <koct9i@gmail.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.16: deleted assertions used VM_BUG_ON()] Signed-off-by:
-
Jason Gunthorpe authored
commit e6bd18f5 upstream. The drivers/infiniband stack uses write() as a replacement for bi-directional ioctl(). This is not safe. There are ways to trigger write calls that result in the return structure that is normally written to user space being shunted off to user specified kernel memory instead. For the immediate repair, detect and deny suspicious accesses to the write API. For long term, update the user space libraries and the kernel API to something that doesn't present the same security vulnerabilities (likely a structured ioctl() interface). The impacted uAPI interfaces are generally only available if hardware from drivers/infiniband is installed in the system. Reported-by:
Jann Horn <jann@thejh.net> Signed-off-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> [ Expanded check to all known write() entry points ] Signed-off-by:
Doug Ledford <dledford@redhat.com> [bwh: Backported to 3.2: - Drop changes to hfi1 - ipath_write() has the same problem, so add the same restriction there] Signed-off-by:
-
Ilya Dryomov authored
commit 811c6688 upstream. A while ago, commit 9875201e ("rbd: fix use-after free of rbd_dev->disk") fixed rbd unmap vs notify race by introducing an exported wrapper for flushing notifies and sticking it into do_rbd_remove(). A similar problem exists on the rbd map path, though: the watch is registered in rbd_dev_image_probe(), while the disk is set up quite a few steps later, in rbd_dev_device_setup(). Nothing prevents a notify from coming in and crashing on a NULL rbd_dev->disk: BUG: unable to handle kernel NULL pointer dereference at 0000000000000050 Call Trace: [<ffffffffa0508344>] rbd_watch_cb+0x34/0x180 [rbd] [<ffffffffa04bd290>] do_event_work+0x40/0xb0 [libceph] [<ffffffff8109d5db>] process_one_work+0x17b/0x470 [<ffffffff8109e3ab>] worker_thread+0x11b/0x400 [<ffffffff8109e290>] ? rescuer_thread+0x400/0x400 [<ffffffff810a5acf>] kthread+0xcf/0xe0 [<ffffffff810b41b3>] ? finish_task_switch+0x53/0x170 [<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140 [<ffffffff81645dd8>] ret_from_fork+0x58/0x90 [<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140 RIP [<ffffffffa050828a>] rbd_dev_refresh+0xfa/0x180 [rbd] If an error occurs during rbd map, we have to error out, potentially tearing down a watch. Just like on rbd unmap, notifies have to be flushed, otherwise rbd_watch_cb() may end up trying to read in the image header after rbd_dev_image_release() has run: Assertion failure in rbd_dev_header_info() at line 4722: rbd_assert(rbd_image_format_valid(rbd_dev->image_format)); Call Trace: [<ffffffff81cccee0>] ? rbd_parent_request_create+0x150/0x150 [<ffffffff81cd4e59>] rbd_dev_refresh+0x59/0x390 [<ffffffff81cd5229>] rbd_watch_cb+0x69/0x290 [<ffffffff81fde9bf>] do_event_work+0x10f/0x1c0 [<ffffffff81107799>] process_one_work+0x689/0x1a80 [<ffffffff811076f7>] ? process_one_work+0x5e7/0x1a80 [<ffffffff81132065>] ? finish_task_switch+0x225/0x640 [<ffffffff81107110>] ? pwq_dec_nr_in_flight+0x2b0/0x2b0 [<ffffffff81108c69>] worker_thread+0xd9/0x1320 [<ffffffff81108b90>] ? process_one_work+0x1a80/0x1a80 [<ffffffff8111b02d>] kthread+0x21d/0x2e0 [<ffffffff8111ae10>] ? kthread_stop+0x550/0x550 [<ffffffff82022802>] ret_from_fork+0x22/0x40 [<ffffffff8111ae10>] ? kthread_stop+0x550/0x550 RIP [<ffffffff81ccd8f9>] rbd_dev_header_info+0xa19/0x1e30 To fix this, a) check if RBD_DEV_FLAG_EXISTS is set before calling revalidate_disk(), b) move ceph_osdc_flush_notifies() call into rbd_dev_header_unwatch_sync() to cover rbd map error paths and c) turn header read-in into a critical section. The latter also happens to take care of rbd map foo@bar vs rbd snap rm foo@bar race. Fixes: http://tracker.ceph.com/issues/15490Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Josh Durgin <jdurgin@redhat.com> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Sascha Hauer authored
commit 5616f367 upstream. The secondary CPU starts up in ARM mode. When the kernel is compiled in thumb2 mode we have to explicitly compile the secondary startup trampoline in ARM mode, otherwise the CPU will go to Nirvana. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reported-by:
Steffen Trumtrar <s.trumtrar@pengutronix.de> Suggested-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Dinh Nguyen <dinguyen@opensource.altera.com> Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Imre Deak authored
commit dab9a266 upstream. During system resume we depended on pci_enable_device() also putting the device into PCI D0 state. This won't work if the PCI device was already enabled but still in D3 state. This is because pci_enable_device() is refcounted and will not change the HW state if called with a non-zero refcount. Leaving the device in D3 will make all subsequent device accesses fail. This didn't cause a problem most of the time, since we resumed with an enable refcount of 0. But it fails at least after module reload because after that we also happen to leak a PCI device enable reference: During probing we call drm_get_pci_dev() which will enable the PCI device, but during device removal drm_put_dev() won't disable it. This is a bug of its own in DRM core, but without much harm as it only leaves the PCI device enabled. Fixing it is also a bit more involved, due to DRM mid-layering and because it affects non-i915 drivers too. The fix in this patch is valid regardless of the problem in DRM core. v2: - Add a code comment about the relation of this fix to the freeze/thaw vs. the suspend/resume phases. (Ville) - Add a code comment about the inconsistent ordering of set power state and device enable calls. (Chris) CC: Ville Syrjälä <ville.syrjala@linux.intel.com> CC: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460979954-14503-1-git-send-email-imre.deak@intel.com (cherry picked from commit 44410cd0) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> [bwh: Backported to 3.16: - Return error code directly - Adjust context] Signed-off-by:
-
Roman Pen authored
commit 346c09f8 upstream. The bug in a workqueue leads to a stalled IO request in MQ ctx->rq_list with the following backtrace: [ 601.347452] INFO: task kworker/u129:5:1636 blocked for more than 120 seconds. [ 601.347574] Tainted: G O 4.4.5-1-storage+ #6 [ 601.347651] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 601.348142] kworker/u129:5 D ffff880803077988 0 1636 2 0x00000000 [ 601.348519] Workqueue: ibnbd_server_fileio_wq ibnbd_dev_file_submit_io_worker [ibnbd_server] [ 601.348999] ffff880803077988 ffff88080466b900 ffff8808033f9c80 ffff880803078000 [ 601.349662] ffff880807c95000 7fffffffffffffff ffffffff815b0920 ffff880803077ad0 [ 601.350333] ffff8808030779a0 ffffffff815b01d5 0000000000000000 ffff880803077a38 [ 601.350965] Call Trace: [ 601.351203] [<ffffffff815b0920>] ? bit_wait+0x60/0x60 [ 601.351444] [<ffffffff815b01d5>] schedule+0x35/0x80 [ 601.351709] [<ffffffff815b2dd2>] schedule_timeout+0x192/0x230 [ 601.351958] [<ffffffff812d43f7>] ? blk_flush_plug_list+0xc7/0x220 [ 601.352208] [<ffffffff810bd737>] ? ktime_get+0x37/0xa0 [ 601.352446] [<ffffffff815b0920>] ? bit_wait+0x60/0x60 [ 601.352688] [<ffffffff815af784>] io_schedule_timeout+0xa4/0x110 [ 601.352951] [<ffffffff815b3a4e>] ? _raw_spin_unlock_irqrestore+0xe/0x10 [ 601.353196] [<ffffffff815b093b>] bit_wait_io+0x1b/0x70 [ 601.353440] [<ffffffff815b056d>] __wait_on_bit+0x5d/0x90 [ 601.353689] [<ffffffff81127bd0>] wait_on_page_bit+0xc0/0xd0 [ 601.353958] [<ffffffff81096db0>] ? autoremove_wake_function+0x40/0x40 [ 601.354200] [<ffffffff81127cc4>] __filemap_fdatawait_range+0xe4/0x140 [ 601.354441] [<ffffffff81127d34>] filemap_fdatawait_range+0x14/0x30 [ 601.354688] [<ffffffff81129a9f>] filemap_write_and_wait_range+0x3f/0x70 [ 601.354932] [<ffffffff811ced3b>] blkdev_fsync+0x1b/0x50 [ 601.355193] [<ffffffff811c82d9>] vfs_fsync_range+0x49/0xa0 [ 601.355432] [<ffffffff811cf45a>] blkdev_write_iter+0xca/0x100 [ 601.355679] [<ffffffff81197b1a>] __vfs_write+0xaa/0xe0 [ 601.355925] [<ffffffff81198379>] vfs_write+0xa9/0x1a0 [ 601.356164] [<ffffffff811c59d8>] kernel_write+0x38/0x50 The underlying device is a null_blk, with default parameters: queue_mode = MQ submit_queues = 1 Verification that nullb0 has something inflight: root@pserver8:~# cat /sys/block/nullb0/inflight 0 1 root@pserver8:~# find /sys/block/nullb0/mq/0/cpu* -name rq_list -print -exec cat {} \; ... /sys/block/nullb0/mq/0/cpu2/rq_list CTX pending: ffff8838038e2400 ... During debug it became clear that stalled request is always inserted in the rq_list from the following path: save_stack_trace_tsk + 34 blk_mq_insert_requests + 231 blk_mq_flush_plug_list + 281 blk_flush_plug_list + 199 wait_on_page_bit + 192 __filemap_fdatawait_range + 228 filemap_fdatawait_range + 20 filemap_write_and_wait_range + 63 blkdev_fsync + 27 vfs_fsync_range + 73 blkdev_write_iter + 202 __vfs_write + 170 vfs_write + 169 kernel_write + 56 So blk_flush_plug_list() was called with from_schedule == true. If from_schedule is true, that means that finally blk_mq_insert_requests() offloads execution of __blk_mq_run_hw_queue() and uses kblockd workqueue, i.e. it calls kblockd_schedule_delayed_work_on(). That means, that we race with another CPU, which is about to execute __blk_mq_run_hw_queue() work. Further debugging shows the following traces from different CPUs: CPU#0 CPU#1 ---------------------------------- ------------------------------- reqeust A inserted STORE hctx->ctx_map[0] bit marked kblockd_schedule...() returns 1 <schedule to kblockd workqueue> request B inserted STORE hctx->ctx_map[1] bit marked kblockd_schedule...() returns 0 *** WORK PENDING bit is cleared *** flush_busy_ctxs() is executed, but bit 1, set by CPU#1, is not observed As a result request B pended forever. This behaviour can be explained by speculative LOAD of hctx->ctx_map on CPU#0, which is reordered with clear of PENDING bit and executed _before_ actual STORE of bit 1 on CPU#1. The proper fix is an explicit full barrier <mfence>, which guarantees that clear of PENDING bit is to be executed before all possible speculative LOADS or STORES inside actual work function. Signed-off-by:
Roman Pen <roman.penyaev@profitbricks.com> Cc: Gioh Kim <gi-oh.kim@profitbricks.com> Cc: Michael Wang <yun.wang@profitbricks.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: linux-block@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Conrad Kostecki authored
commit 037e1197 upstream. Fixes audio output on a ThinkPad X260, when using Lenovo CES 2013 docking station series (basic, pro, ultra). Signed-off-by:
Conrad Kostecki <ck+linuxkernel@bl4ckb0x.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Eric Dumazet authored
commit fc96256c upstream. When multiple skb are TX-completed in a row, we might incorrectly keep a timestamp of a prior skb and cause extra work. Fixes: ec693d47 ("net/mlx4_en: Add HW timestamping (TS) support") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Ilya Dryomov authored
commit 6c1ea260 upstream. Starting the kernel client with cephx disabled and then enabling cephx and restarting userspace daemons can result in a crash: [262671.478162] BUG: unable to handle kernel paging request at ffffebe000000000 [262671.531460] IP: [<ffffffff811cd04a>] kfree+0x5a/0x130 [262671.584334] PGD 0 [262671.635847] Oops: 0000 [#1] SMP [262672.055841] CPU: 22 PID: 2961272 Comm: kworker/22:2 Not tainted 4.2.0-34-generic #39~14.04.1-Ubuntu [262672.162338] Hardware name: Dell Inc. PowerEdge R720/068CDY, BIOS 2.4.3 07/09/2014 [262672.268937] Workqueue: ceph-msgr con_work [libceph] [262672.322290] task: ffff88081c2d0dc0 ti: ffff880149ae8000 task.ti: ffff880149ae8000 [262672.428330] RIP: 0010:[<ffffffff811cd04a>] [<ffffffff811cd04a>] kfree+0x5a/0x130 [262672.535880] RSP: 0018:ffff880149aeba58 EFLAGS: 00010286 [262672.589486] RAX: 000001e000000000 RBX: 0000000000000012 RCX: ffff8807e7461018 [262672.695980] RDX: 000077ff80000000 RSI: ffff88081af2be04 RDI: 0000000000000012 [262672.803668] RBP: ffff880149aeba78 R08: 0000000000000000 R09: 0000000000000000 [262672.912299] R10: ffffebe000000000 R11: ffff880819a60e78 R12: ffff8800aec8df40 [262673.021769] R13: ffffffffc035f70f R14: ffff8807e5b138e0 R15: ffff880da9785840 [262673.131722] FS: 0000000000000000(0000) GS:ffff88081fac0000(0000) knlGS:0000000000000000 [262673.245377] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [262673.303281] CR2: ffffebe000000000 CR3: 0000000001c0d000 CR4: 00000000001406e0 [262673.417556] Stack: [262673.472943] ffff880149aeba88 ffff88081af2be04 ffff8800aec8df40 ffff88081af2be04 [262673.583767] ffff880149aeba98 ffffffffc035f70f ffff880149aebac8 ffff8800aec8df00 [262673.694546] ffff880149aebac8 ffffffffc035c89e ffff8807e5b138e0 ffff8805b047f800 [262673.805230] Call Trace: [262673.859116] [<ffffffffc035f70f>] ceph_x_destroy_authorizer+0x1f/0x50 [libceph] [262673.968705] [<ffffffffc035c89e>] ceph_auth_destroy_authorizer+0x3e/0x60 [libceph] [262674.078852] [<ffffffffc0352805>] put_osd+0x45/0x80 [libceph] [262674.134249] [<ffffffffc035290e>] remove_osd+0xae/0x140 [libceph] [262674.189124] [<ffffffffc0352aa3>] __reset_osd+0x103/0x150 [libceph] [262674.243749] [<ffffffffc0354703>] kick_requests+0x223/0x460 [libceph] [262674.297485] [<ffffffffc03559e2>] ceph_osdc_handle_map+0x282/0x5e0 [libceph] [262674.350813] [<ffffffffc035022e>] dispatch+0x4e/0x720 [libceph] [262674.403312] [<ffffffffc034bd91>] try_read+0x3d1/0x1090 [libceph] [262674.454712] [<ffffffff810ab7c2>] ? dequeue_entity+0x152/0x690 [262674.505096] [<ffffffffc034cb1b>] con_work+0xcb/0x1300 [libceph] [262674.555104] [<ffffffff8108fb3e>] process_one_work+0x14e/0x3d0 [262674.604072] [<ffffffff810901ea>] worker_thread+0x11a/0x470 [262674.652187] [<ffffffff810900d0>] ? rescuer_thread+0x310/0x310 [262674.699022] [<ffffffff810957a2>] kthread+0xd2/0xf0 [262674.744494] [<ffffffff810956d0>] ? kthread_create_on_node+0x1c0/0x1c0 [262674.789543] [<ffffffff817bd81f>] ret_from_fork+0x3f/0x70 [262674.834094] [<ffffffff810956d0>] ? kthread_create_on_node+0x1c0/0x1c0 What happens is the following: (1) new MON session is established (2) old "none" ac is destroyed (3) new "cephx" ac is constructed ... (4) old OSD session (w/ "none" authorizer) is put ceph_auth_destroy_authorizer(ac, osd->o_auth.authorizer) osd->o_auth.authorizer in the "none" case is just a bare pointer into ac, which contains a single static copy for all services. By the time we get to (4), "none" ac, freed in (2), is long gone. On top of that, a new vtable installed in (3) points us at ceph_x_destroy_authorizer(), so we end up trying to destroy a "none" authorizer with a "cephx" destructor operating on invalid memory! To fix this, decouple authorizer destruction from ac and do away with a single static "none" authorizer by making a copy for each OSD or MDS session. Authorizers themselves are independent of ac and so there is no reason for destroy_authorizer() to be an ac op. Make it an op on the authorizer itself by turning ceph_authorizer into a real struct. Fixes: http://tracker.ceph.com/issues/15447Reported-by:
Alan Zhang <alan.zhang@linux.com> Signed-off-by:
Sage Weil <sage@redhat.com> [bwh: Backported to 3.16: - Implementation of ceph_x_destroy_authorizer() is different - Adjust context] Signed-off-by:
-
Ilya Dryomov authored
commit b28ec2f3 upstream. a255651d ("ceph: ensure auth ops are defined before use") made kfree() in put_osd() conditional on the authorizer. A mechanical mistake most likely - fix it. Cc: Alex Elder <elder@linaro.org> Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Jasem Mutlaq authored
commit 613ac23a upstream. Adding VID:PID for Straizona Focusers to cp210x driver. Signed-off-by:
Jasem Mutlaq <mutlaqja@ikarustech.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Mike Manning authored
commit 1d377f4d upstream. The Link ECU is an aftermarket ECU computer for vehicles that provides full tuning abilities as well as datalogging and displaying capabilities via the USB to Serial adapter built into the device. Signed-off-by:
Mike Manning <michael@bsch.com.au> Signed-off-by:
-
Linus Lüssing authored
commit c4fdb6cf upstream. When removing a single interface while a broadcast or ogm packet is still pending then we will free the forward packet without releasing the queue slots again. This patch is supposed to fix this issue. Fixes: 6d5808d4 ("batman-adv: Add missing hardif_free_ref in forw_packet_free") Signed-off-by:
Linus Lüssing <linus.luessing@c0d3.blue> [sven@narfation.org: fix conflicts with current version] Signed-off-by:
-
Sven Eckelmann authored
commit d1a65f17 upstream. _batadv_update_route rcu_derefences orig_ifinfo->router outside of a spinlock protected region to print some information messages to the debug log. But this pointer is not checked again when the new pointer is assigned in the spinlock protected region. Thus is can happen that the value of orig_ifinfo->router changed in the meantime and thus the reference counter of the wrong router gets reduced after the spinlock protected region. Just rcu_dereferencing the value of orig_ifinfo->router inside the spinlock protected region (which also set the new pointer) is enough to get the correct old router object. Fixes: e1a5382f ("batman-adv: Make orig_node->router an rcu protected pointer") Signed-off-by:
-
Sven Eckelmann authored
commit c7829666 upstream. The encapsulated ethernet and VLAN header may be outside the received ethernet frame. Thus the skb buffer size has to be checked before it can be parsed to find out if it encapsulates another batman-adv packet. Fixes: 42019357 ("batman-adv: softif bridge loop avoidance") Signed-off-by:
-
Laszlo Ersek authored
commit 630ba0cc upstream. The variable_matches() function can currently read "var_name[len]", for example when: - var_name[0] == 'a', - len == 1 - match_name points to the NUL-terminated string "ab". This function is supposed to accept "var_name" inputs that are not NUL-terminated (hence the "len" parameter"). Document the function, and access "var_name[*match]" only if "*match" is smaller than "len". Reported-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Laszlo Ersek <lersek@redhat.com> Cc: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@coreos.com> Cc: Jason Andryuk <jandryuk@gmail.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Link: http://thread.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/86906Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
-
Javier Martinez Canillas authored
commit 10ff4c52 upstream. The exynos5 I2C controller driver always prepares and enables a clock before using it and then disables unprepares it when the clock is not used anymore. But this can cause a possible ABBA deadlock in some scenarios since a driver that uses regmap to access its I2C registers, will first grab the regmap lock and then the I2C xfer function will grab the prepare lock when preparing the I2C clock. But since the clock driver also uses regmap for I2C accesses, preparing a clock will first grab the prepare lock and then the regmap lock when using the regmap API. An example of this happens on the Exynos5422 Odroid XU4 board where a s2mps11 PMIC is used and both the s2mps11 regulators and clk drivers share the same I2C regmap. The possible deadlock is reported by the kernel lockdep: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(sec_core:428:(regmap)->lock); lock(prepare_lock); lock(sec_core:428:(regmap)->lock); lock(prepare_lock); *** DEADLOCK *** Fix it by leaving the code prepared on probe and use {en,dis}able in the I2C transfer function. This patch is similar to commit 34e81ad5 ("i2c: s3c2410: fix ABBA deadlock by keeping clock prepared") that fixes the same bug in other driver for an I2C controller found in Samsung SoCs. Reported-by:
Anand Moon <linux.amoon@gmail.com> Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Jan Beulich authored
commit 103f6112 upstream. Huge pages are not normally available to PV guests. Not suppressing hugetlbfs use results in an endless loop of page faults when user mode code tries to access a hugetlbfs mapped area (since the hypervisor denies such PTEs to be created, but error indications can't be propagated out of xen_set_pte_at(), just like for various of its siblings), and - once killed in an oops like this: kernel BUG at .../fs/hugetlbfs/inode.c:428! invalid opcode: 0000 [#1] SMP ... RIP: e030:[<ffffffff811c333b>] [<ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320 ... Call Trace: [<ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40 [<ffffffff81167b3d>] evict+0xbd/0x1b0 [<ffffffff8116514a>] __dentry_kill+0x19a/0x1f0 [<ffffffff81165b0e>] dput+0x1fe/0x220 [<ffffffff81150535>] __fput+0x155/0x200 [<ffffffff81079fc0>] task_work_run+0x60/0xa0 [<ffffffff81063510>] do_exit+0x160/0x400 [<ffffffff810637eb>] do_group_exit+0x3b/0xa0 [<ffffffff8106e8bd>] get_signal+0x1ed/0x470 [<ffffffff8100f854>] do_signal+0x14/0x110 [<ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0 [<ffffffff814178a5>] retint_user+0x8/0x13 This is CVE-2016-3961 / XSA-174. Reported-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
Jan Beulich <jbeulich@suse.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Juergen Gross <JGross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: xen-devel <xen-devel@lists.xenproject.org> Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Dominik Dingel authored
commit 7f9be775 upstream. On s390 we only can enable hugepages if the underlying hardware/hypervisor also does support this. Common code now would assume this to be signaled by setting HPAGE_SHIFT to 0. But on s390, where we only support one hugepage size, there is a link between HPAGE_SHIFT and pageblock_order. So instead of setting HPAGE_SHIFT to 0, we will implement the check for the hardware capability. Signed-off-by:
Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
-
Dominik Dingel authored
commit 2531c8cf upstream. s390 has a constant hugepage size, by setting HPAGE_SHIFT we also change e.g. the pageblock_order, which should be independent in respect to hugepage support. With this patch every architecture is free to define how to check for hugepage support. Signed-off-by:
-
Ben Hutchings authored
commit f43bfaed upstream. atl2 includes NETIF_F_SG in hw_features even though it has no support for non-linear skbs. This bug was originally harmless since the driver does not claim to implement checksum offload and that used to be a requirement for SG. Now that SG and checksum offload are independent features, if you explicitly enable SG *and* use one of the rare protocols that can use SG without checkusm offload, this potentially leaks sensitive information (before you notice that it just isn't working). Therefore this obscure bug has been designated CVE-2016-2117. Reported-by:
Justin Yackoski <jyackoski@crypto-nite.com> Signed-off-by:
-
Neil Armstrong authored
commit 210990b0 upstream. When the DaVinci emac driver is removed and re-probed, the actual pdev->dev.platform_data is populated with an unwanted valid pointer saved by the previous davinci_emac_of_get_pdata() call, causing a kernel crash when calling priv->int_disable() in emac_int_disable(). Unable to handle kernel paging request at virtual address c8622a80 ... [<c0426fb4>] (emac_int_disable) from [<c0427700>] (emac_dev_open+0x290/0x5f8) [<c0427700>] (emac_dev_open) from [<c04c00ec>] (__dev_open+0xb8/0x120) [<c04c00ec>] (__dev_open) from [<c04c0370>] (__dev_change_flags+0x88/0x14c) [<c04c0370>] (__dev_change_flags) from [<c04c044c>] (dev_change_flags+0x18/0x48) [<c04c044c>] (dev_change_flags) from [<c052bafc>] (devinet_ioctl+0x6b4/0x7ac) [<c052bafc>] (devinet_ioctl) from [<c04a1428>] (sock_ioctl+0x1d8/0x2c0) [<c04a1428>] (sock_ioctl) from [<c014f054>] (do_vfs_ioctl+0x41c/0x600) [<c014f054>] (do_vfs_ioctl) from [<c014f2a4>] (SyS_ioctl+0x6c/0x7c) [<c014f2a4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x1c) Fixes: 42f59967 ("net: ethernet: davinci_emac: add OF support") Cc: Brian Hutchinson <b.hutchman@gmail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
Neil Armstrong authored
commit 99164f9e upstream. In order to avoid an Unbalanced pm_runtime_enable in the DaVinci emac driver when the device is removed and re-probed, and a pm_runtime_disable() call in davinci_emac_remove(). Actually, using unbind/bind on a TI DM8168 SoC gives : $ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/unbind net eth1: DaVinci EMAC: davinci_emac_remove() $ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/bind davinci_emac 4a120000.ethernet: Unbalanced pm_runtime_enable Cc: Brian Hutchinson <b.hutchman@gmail.com> Fixes: 3ba97381 ("net: ethernet: davinci_emac: add pm_runtime support") Signed-off-by:
-
Davidlohr Bueso authored
commit fe1bce9e upstream. Otherwise an incoming waker on the dest hash bucket can miss the waiter adding itself to the plist during the lockless check optimization (small window but still the correct way of doing this); similarly to the decrement counterpart. Suggested-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Davidlohr Bueso <dbueso@suse.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: bigeasy@linutronix.de Cc: dvhart@infradead.org Link: http://lkml.kernel.org/r/1461208164-29150-1-git-send-email-dave@stgolabs.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Alex Deucher authored
commit bcb31eba upstream. bug: https://bugs.freedesktop.org/show_bug.cgi?id=76490Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Anton Blanchard authored
commit 6997e57d upstream. The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU feature value, meaning all the remaining elements initialise the wrong values. This means instead of checking for byte 5, bit 0, we check for byte 0, bit 0, and then we incorrectly set the CPU feature bit as well as MMU feature bit 1 and CPU user feature bits 0 and 2 (5). Checking byte 0 bit 0 (IBM numbering), means we're looking at the "Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU. In practice that bit is set on all platforms which have the property. This means we set CPU_FTR_REAL_LE always. In practice that seems not to matter because all the modern cpus which have this property also implement REAL_LE, and we've never needed to disable it. We're also incorrectly setting MMU feature bit 1, which is: #define MMU_FTR_TYPE_8xx 0x00000002 Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E code, which can't run on the same cpus as scan_features(). So this also doesn't matter in practice. Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2 is not currently used, and bit 0 is: #define PPC_FEATURE_PPC_LE 0x00000001 Which says the CPU supports the old style "PPC Little Endian" mode. Again this should be harmless in practice as no 64-bit CPUs implement that mode. Fix the code by adding the missing initialisation of the MMU feature. Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It would be unsafe to start using it as old kernels incorrectly set it. Fixes: 44ae3ab3 ("powerpc: Free up some CPU feature bits by moving out MMU-related features") Signed-off-by:
-
Chris Wilson authored
commit db9f9203 upstream. Holding a reference to the containing task_struct is not sufficient to prevent the mm_struct from being reaped under memory pressure. If this happens whilst we are calling get_user_pages(), explosions erupt - sometimes an immediate GPF, sometimes page flag corruption. To prevent the target mm from being reaped as we are reading from it, acquire a reference before we begin. Testcase: igt/gem_shrink/*userptr Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-2-git-send-email-chris@chris-wilson.co.uk (cherry picked from commit 40313f0c) Signed-off-by:
-
Stephen Boyd authored
commit eda5ecc0 upstream. The trigger delay algorithm that converts from microseconds to the register value looks incorrect. According to most of the PMIC documentation, the equation is delay (Seconds) = (1 / 1024) * 2 ^ (x + 4) except for one case where the documentation looks to have a formatting issue and the equation looks like delay (Seconds) = (1 / 1024) * 2 x + 4 Most likely this driver was written with the improper documentation to begin with. According to the downstream sources the valid delays are from 2 seconds to 1/64 second, and the latter equation just doesn't make sense for that. Let's fix the algorithm and the range check to match the documentation and the downstream sources. Reported-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: 92d57a73 ("input: Add support for Qualcomm PMIC8XXX power key") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Tested-by:
John Stultz <john.stultz@linaro.org> Acked-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 07d2390e upstream. In certain probe conditions the interrupt came right after registering the handler causing a NULL pointer exception because of uninitialized waitqueue: $ udevadm trigger i2c-gpio i2c-gpio-1: using pins 143 (SDA) and 144 (SCL) i2c-gpio i2c-gpio-3: using pins 53 (SDA) and 52 (SCL) Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = e8b38000 [00000000] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: snd_soc_i2s(+) i2c_gpio(+) snd_soc_idma snd_soc_s3c_dma snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer snd soundcore ac97_bus spi_s3c64xx pwm_samsung dwc2 exynos_adc phy_exynos_usb2 exynosdrm exynos_rng rng_core rtc_s3c CPU: 0 PID: 717 Comm: data-provider-m Not tainted 4.6.0-rc1-next-20160401-00011-g1b8d87473b9e-dirty #101 Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) (...) (__wake_up_common) from [<c0379624>] (__wake_up+0x38/0x4c) (__wake_up) from [<c0a41d30>] (ak8975_irq_handler+0x28/0x30) (ak8975_irq_handler) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140) (handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68) (handle_irq_event) from [<c0389c40>] (handle_edge_irq+0xf0/0x19c) (handle_edge_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34) (generic_handle_irq) from [<c05ee360>] (exynos_eint_gpio_irq+0x50/0x68) (exynos_eint_gpio_irq) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140) (handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68) (handle_irq_event) from [<c0389a70>] (handle_fasteoi_irq+0xb4/0x194) (handle_fasteoi_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34) (generic_handle_irq) from [<c03860b4>] (__handle_domain_irq+0x5c/0xb4) (__handle_domain_irq) from [<c0301774>] (gic_handle_irq+0x54/0x94) (gic_handle_irq) from [<c030c910>] (__irq_usr+0x50/0x80) The bug was reproduced on exynos4412-trats2 (with a max77693 device also using i2c-gpio) after building max77693 as a module. Fixes: 94a6d5cf ("iio:ak8975 Implement data ready interrupt handling") Signed-off-by:
Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Eric Dumazet authored
commit 6517eb59 upstream. On 64bit kernels, device stats are 64bit wide, not 32bit. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Heiko Carstens authored
commit 84976952 upstream. arch_spin_lock_wait_flags() checks if a spinlock is not held before trying a compare and swap instruction. If the lock is unlocked it tries the compare and swap instruction, however if a different cpu grabbed the lock in the meantime the instruction will fail as expected. Subsequently the arch_spin_lock_wait_flags() incorrectly tries to figure out if the cpu that holds the lock is running. However it is using the wrong cpu number for this (-1) and then will also yield the current cpu to the wrong cpu. Fix this by adding a missing continue statement. Fixes: 470ada6b ("s390/spinlock: refactor arch_spin_lock_wait[_flags]") Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by:
-
Tom Lendacky authored
commit f709b45e upstream. Prevent information from leaking to userspace by doing a memset to 0 of the export state structure before setting the structure values and copying it. This prevents un-initialized padding areas from being copied into the export area. Reported-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
