- 09 Apr, 2015 40 commits
-
-
Takashi Iwai authored
commit 4c523ef6 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Takashi Iwai authored
commit b4a18c8b upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Takashi Iwai authored
commit e8371aa0 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
Paul Handrigan <Paul.Handrigan@cirrus.com> Signed-off-by:
-
Takashi Iwai authored
commit d7f58db4 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Eric Nelson authored
commit c7d910b8 upstream. The SGTL5000_CHIP_ANA_POWER register is cached. Update the cached value instead of writing it directly. Patch inspired by Russell King's more colorful remarks in this patch: https://github.com/SolidRun/linux-imx6-3.14/commit/dd4bf6aSigned-off-by:
Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by:
-
willy tarreau authored
commit 71f6d1b3 upstream. Right now the mvneta driver doesn't handle Tx IRQ, and relies on two mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx() and a timer. If a burst of packets is emitted faster than the device can send them, then the queue is stopped until next wake-up of the timer 10ms later. This causes jerky output traffic with bursts and pauses, making it difficult to reach line rate with very few streams. A test on UDP traffic shows that it's not possible to go beyond 134 Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed traffic tends to observe pauses as well if the traffic is bursty, making it even burstier after the wake-up. It seems that this feature was inherited from the original driver but nothing there mentions any reason for not using the interrupt instead, which the chip supports. Thus, this patch enables Tx interrupts and removes the timer. It does the two at once because it's not really possible to make the two mechanisms coexist, so a split patch doesn't make sense. First tests performed on a Mirabox (Armada 370) show that less CPU seems to be used when sending traffic. One reason might be that we now call the mvneta_tx_done_gbe() with a mask indicating which queues have been done instead of looping over all of them. The same UDP test above now happily reaches 987 Mbps / 87.7 kpps. Single-stream TCP traffic can now more easily reach line rate. HTTP transfers of 1 MB objects over a single connection went from 730 to 840 Mbps. It is even possible to go significantly higher (>900 Mbps) by tweaking tcp_tso_win_divisor. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Arnaud Ebalard <arno@natisbad.org> Cc: Eric Dumazet <eric.dumazet@gmail.com> Tested-by:
Arnaud Ebalard <arno@natisbad.org> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
willy tarreau authored
commit 40ba35e7 upstream. Marvell has not published the chip's datasheet yet, so it's very hard to find the relevant bits to manipulate to change the IRQ behaviour. Fortunately, these bits are described in the proprietary LSP patch set which is publicly available here : http://www.plugcomputer.org/downloads/mirabox/ So let's put them back in the driver in order to reduce the burden of current and future maintenance. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
commit 29021366 upstream. If a queue timeout is reported, we can oops because of some schedules while the caller is atomic, as shown below : mvneta d0070000.ethernet eth0: tx timeout BUG: scheduling while atomic: bash/1528/0x00000100 Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv] CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180 [<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc) [<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64) [<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c) [<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec) [<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118) [<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14) [<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4) [<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170) [<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8) [<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98) [<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60) [<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60) Ben Hutchings attempted to propose a better fix consisting in using a scheduled work for this, but while it fixed this panic, it caused other random freezes and panics proving that the reset sequence in the driver is unreliable and that additional fixes should be investigated. When sending multiple streams over a link limited to 100 Mbps, Tx timeouts happen from time to time, and the driver correctly recovers only when the function is disabled. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Ben Hutchings <ben@decadent.org.uk> Tested-by:
-
willy tarreau authored
commit 74c41b04 upstream. Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything when they update the stats, and as a result, it randomly happens that the stats freeze on SMP if two updates happen during stats retrieval. This is very easily reproducible by starting two HTTP servers and binding each of them to a different CPU, then consulting /proc/net/dev in loops during transfers, the interface should immediately lock up. This issue also randomly happens upon link state changes during transfers, because the stats are collected in this situation, but it takes more attempts to reproduce it. The comments in netdevice.h suggest using per_cpu stats instead to get rid of this issue. This patch implements this. It merges both rx_stats and tx_stats into a single "stats" member with a single syncp. Both mvneta_rx() and mvneta_rx() now only update the a single CPU's counters. In turn, mvneta_get_stats64() does the summing by iterating over all CPUs to get their respective stats. With this change, stats are still correct and no more lockup is encountered. Note that this bug was present since the first import of the mvneta driver. It might make sense to backport it to some stable trees. If so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats out of the hot path". Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Tested-by:
-
willy tarreau authored
commit dc4277dd upstream. Better count packets and bytes in the stack and on 32 bit then accumulate them at the end for once. This saves two memory writes and two memory barriers per packet. The incoming packet rate was increased by 4.7% on the Openblocks AX3 thanks to this. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by:
-
Wei Yang authored
[ Upstream commit befdf897 ] pci_match_id() just match the static pci_device_id, which may return NULL if someone binds the driver to a device manually using /sys/bus/pci/drivers/.../new_id. This patch wrap up a helper function __mlx4_remove_one() which does the tear down function but preserve the drv_data. Functions like mlx4_pci_err_detected() and mlx4_restart_one() will call this one with out releasing drvdata. Fixes: 97a5221f "net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset". CC: Bjorn Helgaas <bhelgaas@google.com> CC: Amir Vadai <amirv@mellanox.com> CC: Jack Morgenstein <jackm@dev.mellanox.co.il> CC: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Wei Yang <weiyang@linux.vnet.ibm.com> Acked-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Wei Yang authored
commit 97a5221f upstream. The second parameter of __mlx4_init_one() is used to identify whether the pci_dev is a PF or VF. Currently, when it is invoked in mlx4_pci_slot_reset() this information is missed. This patch match the pci_dev with mlx4_pci_table and passes the pci_device_id.driver_data to __mlx4_init_one() in mlx4_pci_slot_reset(). Signed-off-by:
-
Eric Dumazet authored
commit 5925a055 upstream. sk_dst_cache has __rcu annotation, so we need a cast to avoid following sparse error : include/net/sock.h:1774:19: warning: incorrect type in initializer (different address spaces) include/net/sock.h:1774:19: expected struct dst_entry [noderef] <asn:4>*__ret include/net/sock.h:1774:19: got struct dst_entry *dst Signed-off-by:
kbuild test robot <fengguang.wu@intel.com> Fixes: 7f502361 ("ipv4: irq safe sk_dst_[re]set() and ipv4_sk_update_pmtu() fix") Signed-off-by:
-
Thomas Fitzsimmons authored
commit 0a198587 upstream. This commit fixes the command value generated for CSUM calculation when running in big endian mode. The Ethernet protocol ID for IP was being unconditionally byte-swapped in the layer 3 protocol check (with swab16), which caused the mvneta driver to not function correctly in big endian mode. This patch byte-swaps the ID conditionally with htons. Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by:
Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by:
-
Ben Hutchings authored
commit 640d7efe upstream. *_result[len] is parsed as *(_result[len]) which is not at all what we want to touch here. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Fixes: 84a7c0b1 ("dns_resolver: assure that dns_query() result is null-terminated") Signed-off-by:
-
Gao feng authored
commit 33d99113 upstream. commit 25fb6ca4 "net IPv6 : Fix broken IPv6 routing table after loopback down-up" allocates addrconf router for ipv6 address when lo device up. but commit a881ae1f "ipv6:don't call addrconf_dst_alloc again when enable lo" breaks this behavior. Since the addrconf router is moved to the garbage list when lo device down, we should release this router and rellocate a new one for ipv6 address when lo device up. This patch solves bug 67951 on bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=67951 change from v1: use ip6_rt_put to repleace ip6_del_rt, thanks Hannes! change code style, suggested by Sergei. CC: Sabrina Dubroca <sd@queasysnail.net> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by:
Weilong Chen <chenweilong@huawei.com> Signed-off-by:
Gao feng <gaofeng@cn.fujitsu.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Zoltan Kiss authored
commit 36d5fe6a upstream. skb_zerocopy can copy elements of the frags array between skbs, but it doesn't orphan them. Also, it doesn't handle errors, so this patch takes care of that as well, and modify the callers accordingly. skb_tx_error() is also added to the callers so they will signal the failed delivery towards the creator of the skb. Signed-off-by:
Zoltan Kiss <zoltan.kiss@citrix.com> Signed-off-by:
-
Joerg Roedel authored
commit d97eb896 upstream. When an interrupt is migrated away from a cpu it will stay in its vector_irq array until smp_irq_move_cleanup_interrupt succeeded. The cfg->move_in_progress flag is cleared already when the IPI was sent. When the interrupt is destroyed after migration its 'struct irq_desc' is freed and the vector_irq arrays are cleaned up. But since cfg->move_in_progress is already 0 the references at cpus before the last migration will not be cleared. So this would leave a reference to an already destroyed irq alive. When the cpu is taken down at this point, the check_irq_vectors_for_cpu_disable() function finds a valid irq number in the vector_irq array, but gets NULL for its descriptor and dereferences it, causing a kernel panic. This has been observed on real systems at shutdown. Add a check to check_irq_vectors_for_cpu_disable() for a valid 'struct irq_desc' to prevent this issue. Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by:
Jiang Liu <jiang.liu@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <JBeulich@suse.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Yinghai Lu <yinghai@kernel.org> Cc: alnovak@suse.com Cc: joro@8bytes.org Link: http://lkml.kernel.org/r/20150204132754.GA10078@suse.deSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Joerg Roedel authored
commit 9db4ad91 upstream. Check for the ->map and not the ->unmap pointer. Signed-off-by:
-
Jan Kiszka authored
commit acead1b0 upstream. Add CPU ID for Atom N2600/N2800 processors. Datasheets indicate support for this, detailed information about potential quirks or limitations are missing, though. So we just reuse the definition for the previous ATOM series. Tests on N2800 systems showed that this addition is fine an can reduce power consumption by about 0.25 W (personally confirmed on Intel DN2800MT). Signed-off-by:
Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by:
Len Brown <len.brown@intel.com> Signed-off-by:
-
Romeo Cane authored
commit 1028ccf5 upstream. Declaring sys_call_table as a pointer causes the compiler to generate the wrong lookup code in arch_syscall_addr(). <arch_syscall_addr>: lis r9,-16384 rlwinm r3,r3,2,0,29 - lwz r11,30640(r9) - lwzx r3,r11,r3 + addi r9,r9,30640 + lwzx r3,r9,r3 blr The actual sys_call_table symbol, declared in assembler, is an array. If we lie about that to the compiler we get the wrong code generated, as above. This definition seems only to be used by the syscall tracing code in kernel/trace/trace_syscalls.c. With this patch I can successfully use the syscall tracepoints: bash-3815 [002] .... 333.239082: sys_write -> 0x2 bash-3815 [002] .... 333.239087: sys_dup2(oldfd: a, newfd: 1) bash-3815 [002] .... 333.239088: sys_dup2 -> 0x1 bash-3815 [002] .... 333.239092: sys_fcntl(fd: a, cmd: 1, arg: 0) bash-3815 [002] .... 333.239093: sys_fcntl -> 0x1 bash-3815 [002] .... 333.239094: sys_close(fd: a) bash-3815 [002] .... 333.239094: sys_close -> 0x0 Signed-off-by:
Romeo Cane <romeo.cane.ext@coriant.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Quentin Casasnovas authored
commit f84598bd upstream. mc_saved_tmp is a static array allocated on the stack, we need to make sure mc_saved_count stays within its bounds, otherwise we're overflowing the stack in _save_mc(). A specially crafted microcode header could lead to a kernel crash or potentially kernel execution. Signed-off-by:
Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Link: http://lkml.kernel.org/r/1422964824-22056-1-git-send-email-quentin.casasnovas@oracle.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Andy Lutomirski authored
commit ff7e0055 upstream. The commit 4982223e module: set nx before marking module MODULE_STATE_COMING. introduced a regression: if a module fails to parse its arguments or if mod_sysfs_setup fails, then the module's memory will be freed while still read-only. Anything that reuses that memory will crash as soon as it tries to write to it. Cc: stable@vger.kernel.org # v3.16 Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Rusty Russell authored
commit 4982223e upstream. We currently set RO & NX on modules very late: after we move them from MODULE_STATE_UNFORMED to MODULE_STATE_COMING, and after we call parse_args() (which can exec code in the module). Much better is to do it in complete_formation() and then call the notifier. This means that the notifiers will be called on a module which is already RO & NX, so that may cause problems (ftrace already changed so they're unaffected). Signed-off-by:
-
Michael Ellerman authored
commit 875ebe94 upstream. Anton has a busy ppc64le KVM box where guests sometimes hit the infamous "kernel BUG at kernel/smpboot.c:134!" issue during boot: BUG_ON(td->cpu != smp_processor_id()); Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops output confirms it: CPU: 0 Comm: watchdog/130 The problem is that we aren't ensuring the CPU active bit is set for the secondary before allowing the master to continue on. The master unparks the secondary CPU's kthreads and the scheduler looks for a CPU to run on. It calls select_task_rq() and realises the suggested CPU is not in the cpus_allowed mask. It then ends up in select_fallback_rq(), and since the active bit isnt't set we choose some other CPU to run on. This seems to have been introduced by 6acbfb96 "sched: Fix hotplug vs. set_cpus_allowed_ptr()", which changed from setting active before online to setting active after online. However that was in turn fixing a bug where other code assumed an active CPU was also online, so we can't just revert that fix. The simplest fix is just to spin waiting for both active & online to be set. We already have a barrier prior to set_cpu_online() (which also sets active), to ensure all other setup is completed before online & active are set. Fixes: 6acbfb96 ("sched: Fix hotplug vs. set_cpus_allowed_ptr()") Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Steven Capper authored
commit ded94779 upstream. For LPAE, we have the following means for encoding writable or dirty ptes: L_PTE_DIRTY L_PTE_RDONLY !pte_dirty && !pte_write 0 1 !pte_dirty && pte_write 0 1 pte_dirty && !pte_write 1 1 pte_dirty && pte_write 1 0 So we can't distinguish between writeable clean ptes and read only ptes. This can cause problems with ptes being incorrectly flagged as read only when they are writeable but not dirty. This patch renumbers L_PTE_RDONLY from AP[2] to a software bit #58, and adds additional logic to set AP[2] whenever the pte is read only or not dirty. That way we can distinguish between clean writeable ptes and read only ptes. HugeTLB pages will use this new logic automatically. We need to add some logic to Transparent HugePages to ensure that they correctly interpret the revised pgprot permissions (L_PTE_RDONLY has moved and no longer matches PMD_SECT_AP2). In the process of revising THP, the names of the PMD software bits have been prefixed with L_ to make them easier to distinguish from their hardware bit counterparts. Signed-off-by:
Steve Capper <steve.capper@linaro.org> Reviewed-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz> [dump.c is not in 3.12]
-
Steven Capper authored
commit f2950706 upstream. Long descriptors on ARM are 64 bits, and some pte functions such as pte_dirty return a bitwise-and of a flag with the pte value. If the flag to be tested resides in the upper 32 bits of the pte, then we run into the danger of the result being dropped if downcast. For example: gather_stats(page, md, pte_dirty(*pte), 1); where pte_dirty(*pte) is downcast to an int. This patch introduces a new macro pte_isset which performs the bitwise and, then performs a double logical invert (where needed) to ensure predictable downcasting. The logical inverse pte_isclear is also introduced. Equivalent pmd functions for Transparent HugePages have also been added. Signed-off-by:
-
Laura Abbott authored
commit efea3403 upstream. The definition of virt_addr_valid is that virt_addr_valid should return true if and only if virt_to_page returns a valid pointer. The current definition of virt_addr_valid only checks against the virtual address range. There's no guarantee that just because a virtual address falls bewteen PAGE_OFFSET and high_memory the associated physical memory has a valid backing struct page. Follow the example of other architectures and convert to pfn_valid to verify that the virtual address is actually valid. The check for an address between PAGE_OFFSET and high_memory is still necessary as vmalloc/highmem addresses are not valid with virt_to_page. Cc: Will Deacon <will.deacon@arm.com> Cc: Nicolas Pitre <nico@linaro.org> Acked-by:
Laura Abbott <lauraa@codeaurora.org> Signed-off-by:
-
Chen Gang authored
commit 4dcc1cf7 upstream. For atomic_cmpxchg(), the type of 'oldval' need be 'int' to match the type of "*ptr" (used by 'ldrex' instruction) and 'old' (used by 'teq' instruction). Reviewed-by:
Chen Gang <gang.chen@asianux.com> Signed-off-by:
-
Chen Gang authored
commit 237f1233 upstream. atomic* value is signed value, and atomic* functions need also process signed value (parameter value, and return value), so 32-bit arm need use 'long long' instead of 'u64'. After replacement, it will also fix a bug for atomic64_add_negative(): "u64 is never less than 0". The modifications are: in vim, use "1,% s/\<u64\>/long long/g" command. remove '__aligned(8)' which is useless for 64-bit. be sure of 80 column limitation after replacement. Acked-by:
-
Jouni Malinen authored
commit 08f6f147 upstream. The VHT supported channel width field is a two bit integer, not a bitfield. cfg80211_chandef_usable() was interpreting it incorrectly and ended up rejecting 160 MHz channel width if the driver indicated support for both 160 and 80+80 MHz channels. Cc: stable@vger.kernel.org (3.16+) Fixes: 3d9d1d66 ("nl80211/cfg80211: support VHT channel configuration") (however, no real drivers had 160 MHz support it until 3.16) Signed-off-by:
Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Vineet Gupta authored
commit e8ef060b upstream. This allows the sdplite/Zebu images to run on OSCI simulation platform Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.14, 3.16 Signed-off-by:
-
Chris Mason authored
commit 6f896054 upstream. Commit 1d52c78a (Btrfs: try not to ENOSPC on log replay) added a check to skip delayed inode updates during log replay because it confuses the enospc code. But the delayed processing will end up ignoring delayed refs from log replay because the inode itself wasn't put through the delayed code. This can end up triggering a warning at commit time: WARNING: CPU: 2 PID: 778 at fs/btrfs/delayed-inode.c:1410 btrfs_assert_delayed_root_empty+0x32/0x34() Which is repeated for each commit because we never process the delayed inode ref update. The fix used here is to change btrfs_delayed_delete_inode_ref to return an error if we're currently in log replay. The caller will do the ref deletion immediately and everything will work properly. Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
NeilBrown authored
commit 4b5060dd upstream. If two threads call bitmap_unplug at the same time, then one might schedule all the writes, and the other might decide that it doesn't need to wait. But really it does. It rarely hurts to wait when it isn't absolutely necessary, and the current code doesn't really focus on 'absolutely necessary' anyway. So just wait always. This can potentially lead to data corruption if a crash happens at an awkward time and data was written before the bitmap was updated. It is very unlikely, but this should go to -stable just to be safe. Appropriate for any -stable. Signed-off-by:
NeilBrown <neilb@suse.de> Cc: stable@vger.kernel.org (please delay until 3.18 is released) Signed-off-by:
-
Ben Dooks authored
commit 63328070 upstream. Currently BUG() uses .word or .hword to create the necessary illegal instructions. However if we are building BE8 then these get swapped by the linker into different illegal instructions in the text. This means that the BUG() macro does not get trapped properly. Change to using <asm/opcodes.h> to provide the necessary ARM instruction building as we cannot rely on gcc/gas having the `.inst` instructions which where added to try and resolve this issue (reported by Dave Martin <Dave.Martin@arm.com>). Signed-off-by:
Ben Dooks <ben.dooks@codethink.co.uk> Reviewed-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
-
Anton Kolesov authored
commit ebc0c74e upstream. Order of registers has changed in GDB moving from 6.8 to 7.5. This patch updates KGDB to work properly with GDB 7.5, though makes it incompatible with 6.8. Signed-off-by:
Anton Kolesov <Anton.Kolesov@synopsys.com> Signed-off-by:
-
Vineet Gupta authored
commit 5c05483e upstream. There are certain test configuration of virtual platform which don't have any real console device (uart/pgu). So add tty0 as a fallback console device to allow system to boot and be accessible via telnet Otherwise with ttyS0 as only console, but 8250 disabled in kernel build, init chokes. Reported-by:
Anton Kolesov <akolesov@synopsys.com> Signed-off-by:
-
Anton Blanchard authored
commit 85101af1 upstream. ABIv2 kernels are failing to backtrace through the kernel. An example: 39.30% readseek2_proce [kernel.kallsyms] [k] find_get_entry | --- find_get_entry __GI___libc_read The problem is in valid_next_sp() where we check that the new stack pointer is at least STACK_FRAME_OVERHEAD below the previous one. ABIv1 has a minimum stack frame size of 112 bytes consisting of 48 bytes and 64 bytes of parameter save area. ABIv2 changes that to 32 bytes with no paramter save area. STACK_FRAME_OVERHEAD is in theory the minimum stack frame size, but we over 240 uses of it, some of which assume that it includes space for the parameter area. We need to work through all our stack defines and rationalise them but let's fix perf now by creating STACK_FRAME_MIN_SIZE and using in valid_next_sp(). This fixes the issue: 30.64% readseek2_proce [kernel.kallsyms] [k] find_get_entry | --- find_get_entry pagecache_get_page generic_file_read_iter new_sync_read vfs_read sys_read syscall_exit __GI___libc_read Cc: stable@vger.kernel.org # 3.16+ Reported-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
-
Bob Moore authored
commit 75ec6e55 upstream. Changes to correct several GPIO issues: 1) The update_rule in a GPIO field definition is now ignored; a read-modify-write operation is never performed for GPIO fields. (Internally, this means that the field assembly/disassembly code is completely bypassed for GPIO.) 2) The Address parameter passed to a GPIO region handler is now the bit offset of the field from a previous Connection() operator. Thus, it becomes a "Pin Number Index" into the Connection() resource descriptor. 3) The bit_width parameter passed to a GPIO region handler is now the exact bit width of the GPIO field. Thus, it can be interpreted as "number of pins". Overall, we can now say that the region handler interface to GPIO handlers is a raw "bit/pin" addressed interface, not a byte-addressed interface like the system_memory handler interface. Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Cc: 3.15+ <stable@vger.kernel.org> # 3.15+ Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Johan Hovold authored
commit 30966910 upstream. Add back some PIDs that were mistakingly remove when reverting commit 73228a05 ("USB: option,zte_ev: move most ZTE CDMA devices to zte_ev"), which apparently did more than its commit message claimed in that it not only moved some PIDs from option to zte_ev but also added some new ones. Fixes: 63a901c0 ("Revert "USB: option,zte_ev: move most ZTE CDMA devices to zte_ev"") Reported-by:
Lei Liu <lei35151@163.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
