The __cpu_logical_map array is statically initialized to 0, which is a valid
MPIDR value. To prevent issues with the current implementation, this patch
defines an MPIDR_INVALID value, and statically initializes the
__cpu_logical_map[] array to it. Entries in the arm_dt_init_cpu_maps()
tmp_map array used to stash DT reg properties while parsing DT are initialized
with the MPIDR_INVALID value as well for consistency.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The introduction of the cpu-map topology node in the cpus node implies
that cpus node might have children that are not cpu nodes. The DT
parsing code needs updating otherwise it would check for cpu nodes
properties in nodes that are not required to contain them, resulting
in warnings that have no bearing on bindings defined in the dts source file.

Cc: <stable@vger.kernel.org> [3.8+]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As it was already suggested by Russell King and Arnd Bergmann:

https://lkml.org/lkml/2013/5/16/133

moxart and gemini seem to be the only platforms using CPU_FA526,
and instead of pointing arm_pm_idle to an empty function from
platform code, it makes sense to remove WFI code from the processor
specific idle function.

Applies to arm-soc/for-next (and 3.10-rc1).

Changes since v1:

1. remove WFI but make sure cpu_fa526_do_idle do not fall through
   to cpu_fa526_dcache_clean_area

Note: moxart boots and prints to UART without this patch, but input is broken.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull ARM SoC fixes from Arnd Bergmann:
 "These are two fixes that came in this week, one for a regression we
  introduced in 3.10 in the GIC interrupt code, and the other one fixes
  a typo in newly introduced code"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  irqchip: gic: call gic_cpu_init() as well in CPU_STARTING_FROZEN case
  ARM: dts: Correct the base address of pinctrl_3 on Exynos5250

Merge tag 'driver-core-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg Kroah-Hartman:
 "Here's a single patch for the firmware core that resolves a reported
  oops in the firmware core that people have been hitting."

* tag 'driver-core-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  firmware loader: fix use-after-free by double abort

Pull USB fixes from Greg Kroah-Hartman:
 "Here are two USB patches for 3.10.

  One updates the Kconfig wording for CONFIG_USB_PHY to make it,
  hopefully, more obvious what this option is (I know you complained
  about this when it hit the tree.) The other is a new device id for a
  driver"

* tag 'usb-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: ti_usb_3410_5052: new device id for Abbot strip port cable
  usb: phy: Improve Kconfig help for CONFIG_USB_PHY

Pul tty fixes from Greg Kroah-Hartman:
 "Here are two tty core fixes that resolve some regressions that have
  been reported recently.  Both tiny fixes, but needed"

* tag 'tty-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix transient pty write() EIO
  tty/vt: Return EBUSY if deallocating VT1 and it is busy

Pull SCSI target fixes from Nicholas Bellinger:
 "Included is the recent tcm_qla2xxx residual underrun length fix from
  Roland, along with Joern's iscsi-target patch for session_lock
  breakage within iscsit_stop_time2retain_timer() code.  Both are CC'ed
  to stable.

  The remaining two are specific to recent iscsi-target + iser
  conversion changes.  One drops some left-over debug noise, and Andy's
  patch fixes configfs attribute handling during an explicit network
  portal feature bit disable when iser-target is unsupported."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Remove left over v3.10-rc debug printks
  target/iscsi: Fix op=disable + error handling cases in np_store_iser
  tcm_qla2xxx: Fix residual for underrun commands that fail
  target/iscsi: don't corrupt bh_count in iscsit_stop_time2retain_timer()

Pull media fixes from Mauro Carvalho Chehab:
 "Another set of fixes for Kernel 3.10.

  This series contain:
   - two Kbuild fixes for randconfig
   - a buffer overflow when using rtl28xuu with r820t tuner
   - one clk fixup on exynos4-is driver"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] Fix build when drivers are builtin and frontend modules
  [media] s5p makefiles: don't override other selections on obj-[ym]
  [media] exynos4-is: Fix FIMC-IS clocks initialization
  [media] rtl28xxu: fix buffer overflow when probing Rafael Micro r820t tuner

Pull vfs fixes from Al Viro:
 "Several fixes for bugs caught while looking through f_pos (ab)users"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  aout32 coredump compat fix
  splice: don't pass the address of ->f_pos to methods
  mconsole: we'd better initialize pos before passing it to vfs_read()...

dump_seek() does SEEK_CUR, not SEEK_SET; native binfmt_aout
handles it correctly (seeks by PAGE_SIZE - sizeof(struct user),
getting the current position to PAGE_SIZE), compat one seeks
by PAGE_SIZE and ends up at PAGE_SIZE + already written...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull x86 fixes from Peter Anvin:
 "This series fixes a couple of build failures, and fixes MTRR cleanup
  and memory setup on very specific memory maps.

  Finally, it fixes triggering backtraces on all CPUs, which was
  inadvertently disabled on x86."

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/efi: Fix dummy variable buffer allocation
  x86: Fix trigger_all_cpu_backtrace() implementation
  x86: Fix section mismatch on load_ucode_ap
  x86: fix build error and kconfig for ia32_emulation and binfmt
  range: Do not add new blank slot with add_range_with_merge
  x86, mtrr: Fix original mtrr range get for mtrr_cleanup

Pull drm radeon fixes from Dave Airlie:
 "One core fix, but mostly radeon fixes for s/r and big endian UVD
  support, and a fix to stop the GPU being reset for no good reason, and
  crashing people's machines."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: update lockup tracking when scheduling in empty ring
  drm/prime: Honor requested file flags when exporting a buffer
  drm/radeon: fix UVD on big endian
  drm/radeon: fix write back suspend regression with uvd v2
  drm/radeon: do not try to uselessly update virtual memory pagetable

Pull ACPI fixes from Rafael Wysocki:

 - Fix for a regression causing a failure to turn on some devices on
   some systems during initialization introduced by a recent revert of
   an ACPI PM change that broke something else.  Fortunately, we know
   exactly what devices are affected, so we can add a fix just for them
   leaving everyone else alone.

 - ACPI power resources initialization fix preventing a NULL pointer
   from being dereferenced in the acpi_add_power_resource() error code
   path.

 - ACPI dock station driver fix that adds missing locking to
   write_undock().

 - ACPI resources allocation fix changing the scope of an old workaround
   so that it doesn't affect systems that aren't actually buggy.  This
   was reported a couple of days ago to fix DMA problems on some new
   platforms so we need it in -stable.  From Mika Westerberg.

* tag 'acpi-3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / LPSS: Power up LPSS devices during enumeration
  ACPI / PM: Fix error code path for power resources initialization
  ACPI / dock: Take ACPI scan lock in write_undock()
  ACPI / resources: call acpi_get_override_irq() only for legacy IRQ resources

Pull KVM fixes from Paolo Bonzini:
 "Three one-line fixes for my first pull request; one for x86 host, one
  for x86 guest, one for PPC"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  x86: kvmclock: zero initialize pvclock shared memory area
  kvm/ppc/booke: Delay kvmppc_lazy_ee_enable
  KVM: x86: remove vcpu's CPL check in host-invoked XCR set

Pull crypto fix from Herbert Xu:
 "This fixes an unaligned crash in XTS mode when using aseni_intel"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: aesni_intel - fix accessing of unaligned memory

Pull Ceph fix from Sage Weil:
 "This fixes a problem preventing the kernel and userland librbd
  libraries from sharing data with the new format 2 images"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: use the correct length for format 2 object names

 * Don't leak random kernel memory to EFI variable NVRAM when attempting
   to initiate garbage collection. Also, free the kernel memory when
   we're done with it instead of leaking - Ben Hutchings
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

1. Check for allocation failure
2. Clear the buffer contents, as they may actually be written to flash
3. Don't leak the buffer

Compile-tested only.

[ Tested successfully on my buggy ASUS machine - Matt ]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

Reported-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Writing 0 when iser was not previously enabled, so succeed but do
nothing so that user-space code doesn't need a try: catch block
when ib_isert logic is not available.

Also, return actual error from add_network_portal using PTR_ERR
during op=enable failure.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

One user visible fix to stop misreport GPU hangs and subsequent resets.
* 'drm-fixes-3.10' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: update lockup tracking when scheduling in empty ring

There might be issue with lockup detection when scheduling on an
empty ring that have been sitting idle for a while. Thus update
the lockup tracking data when scheduling new work in an empty ring.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pull scheduler fixes from Ingo Molnar:
 "Two smaller fixes - plus a context tracking tracing fix that is a bit
  bigger"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tracing/context-tracking: Add preempt_schedule_context() for tracing
  sched: Fix clear NOHZ_BALANCE_KICK
  sched/x86: Construct all sibling maps if smt

Pull perf fixes from Ingo Molnar:
 "Four fixes.  The mmap ones are unfortunately larger than desired -
  fuzzing uncovered bugs that needed perf context life time management
  changes to fix properly"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Fix broken PEBS-LL support on SNB-EP/IVB-EP
  perf: Fix mmap() accounting hole
  perf: Fix perf mmap bugs
  kprobes: Fix to free gone and unused optprobes

Pull cpu idle fixes from Thomas Gleixner:
 - Add a missing irq enable. Fallout of the idle conversion
 - Fix stackprotector wreckage caused by the idle conversion

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  idle: Enable interrupts in the weak arch_cpu_idle() implementation
  idle: Add the stack canary init to cpu_startup_entry()

Pull timer fixes from Thomas Gleixner:
 - Fix inconstinant clock usage in virtual time accounting
 - Fix a build error in KVM caused by the NOHZ work
 - Remove a pointless timekeeping duty assignment which breaks NOHZ
 - Use a proper notifier return value to avoid random behaviour

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick: Remove useless timekeeping duty attribution to broadcast source
  nohz: Fix notifier return val that enforce timekeeping
  kvm: Move guest entry/exit APIs to context_tracking
  vtime: Use consistent clocks among nohz accounting

Pull powerpc fix fro, Benjamin Herrenschmidt:
 "We accidentally broke hugetlbfs on Freescale embedded processors which
  use a slightly different page table layout than our server processors"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Fix bad pmd error with book3E config

Pull tilepro fix from Chris Metcalf:
 "This change allows the older tilepro architecture to be correctly
  built by newer gccs, despite a change that caused gcc to start trying
  to use an out-of-line implementation for __builtin_ffsll().

  This should be inline again starting with gcc 4.7.4 and 4.8.2 or so,
  but meanwhile this change keeps things from breaking, with the only
  cost being a few bytes of code in the kernel to provide __ffsdi2 even
  for compilers that do inline it"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tilepro: work around module link error with gcc 4.7

Pull arm64 perf fix from Catalin Marinas:
 "Perf fix (user-mode PC recording)"

* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  perf: arm64: Record the user-mode PC in the call chain.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

There are a large number of reports that the media build is
not compiling when some drivers are compiled as builtin, while
the needed frontends are compiled as module.

On the last one of such reports:
	From: kbuild test robot <fengguang.wu@intel.com>
	Subject: saa7134-dvb.c:undefined reference to `zl10039_attach'

The .config file has:

	CONFIG_VIDEO_SAA7134=y
	CONFIG_VIDEO_SAA7134_DVB=y
	# CONFIG_MEDIA_ATTACH is not set
	CONFIG_DVB_ZL10039=m

And it produces all those errors:

   drivers/built-in.o: In function `set_type':
   tuner-core.c:(.text+0x2f263e): undefined reference to `tea5767_attach'
   tuner-core.c:(.text+0x2f273e): undefined reference to `tda9887_attach'
   drivers/built-in.o: In function `tuner_probe':
   tuner-core.c:(.text+0x2f2d20): undefined reference to `tea5767_autodetection'
   drivers/built-in.o: In function `av7110_attach':
   av7110.c:(.text+0x330bda): undefined reference to `ves1x93_attach'
   av7110.c:(.text+0x330bf7): undefined reference to `stv0299_attach'
   av7110.c:(.text+0x330c63): undefined reference to `tda8083_attach'
   av7110.c:(.text+0x330d09): undefined reference to `ves1x93_attach'
   av7110.c:(.text+0x330d33): undefined reference to `tda8083_attach'
   av7110.c:(.text+0x330d5d): undefined reference to `stv0297_attach'
   av7110.c:(.text+0x330dbe): undefined reference to `stv0299_attach'
   drivers/built-in.o: In function `tuner_attach_dtt7520x':
   ngene-cards.c:(.text+0x3381cb): undefined reference to `dvb_pll_attach'
   drivers/built-in.o: In function `demod_attach_lg330x':
   ngene-cards.c:(.text+0x33828a): undefined reference to `lgdt330x_attach'
   drivers/built-in.o: In function `demod_attach_stv0900':
   ngene-cards.c:(.text+0x3383d5): undefined reference to `stv090x_attach'
   drivers/built-in.o: In function `cineS2_probe':
   ngene-cards.c:(.text+0x338b7f): undefined reference to `drxk_attach'
   drivers/built-in.o: In function `configure_tda827x_fe':
   saa7134-dvb.c:(.text+0x346ae7): undefined reference to `tda10046_attach'
   drivers/built-in.o: In function `dvb_init':
   saa7134-dvb.c:(.text+0x347283): undefined reference to `mt352_attach'
   saa7134-dvb.c:(.text+0x3472cd): undefined reference to `mt352_attach'
   saa7134-dvb.c:(.text+0x34731c): undefined reference to `tda10046_attach'
   saa7134-dvb.c:(.text+0x34733c): undefined reference to `tda10046_attach'
   saa7134-dvb.c:(.text+0x34735c): undefined reference to `tda10046_attach'
   saa7134-dvb.c:(.text+0x347378): undefined reference to `tda10046_attach'
   saa7134-dvb.c:(.text+0x3473db): undefined reference to `tda10046_attach'
   drivers/built-in.o:saa7134-dvb.c:(.text+0x347502): more undefined references to `tda10046_attach' follow
   drivers/built-in.o: In function `dvb_init':
   saa7134-dvb.c:(.text+0x347812): undefined reference to `mt352_attach'
   saa7134-dvb.c:(.text+0x347951): undefined reference to `mt312_attach'
   saa7134-dvb.c:(.text+0x3479a9): undefined reference to `mt312_attach'
>> saa7134-dvb.c:(.text+0x3479c1): undefined reference to `zl10039_attach'

This is happening because a builtin module can't use directly a symbol
found on a module. By enabling CONFIG_MEDIA_ATTACH, the configuration
becomes valid, as dvb_attach() macro loads the module if needed, making
the symbol available to the builtin module.

While this bug started to appear after the patches that use IS_DEFINED
macro (like changeset 7b34be71), this
bug is a way ancient than that.

The thing is that, before the IS_DEFINED() patches, the logic used to be:

       && defined(MODULE))
struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
					u8 i2c_addr,
					struct i2c_adapter *i2c);
static inline struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
					u8 i2c_addr,
					struct i2c_adapter *i2c)
{
	printk(KERN_WARNING "%s: driver disabled by Kconfig\n", __func__);
	return NULL;
}

The above code, with the .config file used, was evoluting to FALSE
(instead of TRUE as it should be, as CONFIG_DVB_ZL10039 is 'm'),
and were adding the static inline code at saa7134-dvb, instead
of the external call. So, while it weren't producing any compilation
error, the code weren't working either.

So, as the overhead for using CONFIG_MEDIA_ATTACH is minimal, just
enable it, if MODULES is defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Commit c0114709 (irqchip: gic: Perform the gic_secondary_init() call via
CPU notifier) moves gic_secondary_init() that used to be called in
.smp_secondary_init hook into a notifier call.  But it changes the
system behavior a little bit.  Before the commit, gic_cpu_init()
is called not only when kernel brings up the secondary cores but also
when system resuming procedure hot-plugs the cores back to kernel.
While after the commit, the function will not be called in the latter
case, where the 'action' will not be CPU_STARTING but
CPU_STARTING_FROZEN.  This behavior difference at least causes the
following suspend/resume regression on imx6q.

$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
mmc1: card e624 removed
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
PM: Entering mem sleep
PM: suspend of devices complete after 5.930 msecs
PM: suspend devices took 0.010 seconds
PM: late suspend of devices complete after 0.343 msecs
PM: noirq suspend of devices complete after 0.828 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
INFO: rcu_sched detected stalls on CPUs/tasks: { 1 2 3} (detected by 0, t=2102 jiffies, g=4294967169, c=4294967168, q=17)
Task dump for CPU 1:
swapper/1       R running      0     0      1 0x00000000
Backtrace:
[<bf895ff4>] (0xbf895ff4) from [<00000000>] (  (null))
Backtrace aborted due to bad frame pointer <8007ccdc>
Task dump for CPU 2:
swapper/2       R running      0     0      1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] (  (null))
Backtrace aborted due to bad frame pointer <00000002>
Task dump for CPU 3:
swapper/3       R running      0     0      1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] (  (null))

Fix the regression by checking 'action' being CPU_STARTING_FROZEN to
have gic_cpu_init() called for secondary cores when system resumes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The following change fixes the x86 implementation of
trigger_all_cpu_backtrace(), which was previously (accidentally,
as far as I can tell) disabled to always return false as on
architectures that do not implement this function.

trigger_all_cpu_backtrace(), as defined in include/linux/nmi.h,
should call arch_trigger_all_cpu_backtrace() if available, or
return false if the underlying arch doesn't implement this
function.

x86 did provide a suitable arch_trigger_all_cpu_backtrace()
implementation, but it wasn't actually being used because it was
declared in asm/nmi.h, which linux/nmi.h doesn't include. Also,
linux/nmi.h couldn't easily be fixed by including asm/nmi.h,
because that file is not available on all architectures.

I am proposing to fix this by moving the x86 definition of
arch_trigger_all_cpu_backtrace() to asm/irq.h.

Tested via: echo l > /proc/sysrq-trigger

Before the change, this uses a fallback implementation which
shows backtraces on active CPUs (using
smp_call_function_interrupt() )

After the change, this shows NMI backtraces on all CPUs
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1370518875-1346-1-git-send-email-walken@google.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

With this change, we no longer lose the innermost entry in the user-mode
part of the call chain.  See also the x86 port, which includes the ip,
and the corresponding change in arch/arm.
Signed-off-by: Jed Davis <jld@mozilla.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The $obj-m/$obj-y vars should be adding new modules to build, not
overriding it. So, it should never use
	$obj-y := foo.o
instead, it should use:
	$obj-y += foo.o

Failing to do that is very bad, as it will suppress needed modules.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Book3E uses the hugepd at PMD level and don't encode pte directly
at the pmd level. So it will find the lower bits of pmd set
and the pmd_bad check throws error. Infact the current code
will never take the free_hugepd_range call at all because it will
clear the pmd if it find a hugepd pointer. Fix this by clearing
bad pmd only if it is not a hugepd pointer.

This is regression introduced by e2b3d202
"powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format"
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Add product id for Abbott strip port cable for Precision meter which
uses the TI 3410 chip.
Signed-off-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 7cd8407d (ACPI / PM: Do not execute _PS0 for devices without
_PSC during initialization) introduced a regression on some systems
with Intel Lynxpoint Low-Power Subsystem (LPSS) where some devices
need to be powered up during initialization, but their device objects
in the ACPI namespace have _PS0 and _PS3 only (without _PSC or power
resources).

To work around this problem, make the ACPI LPSS driver power up
devices it knows about by using a new helper function
acpi_device_fix_up_power() that does all of the necessary
sanity checks and calls acpi_dev_pm_explicit_set() to put the
device into D0.
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>