Add inet_gro_compute_pseudo and ip6_gro_compute_pseudo. These are
the logical equivalents of inet_compute_pseudo and ip6_compute_pseudo
for GRO path. The IP header is taken from skb_gro_network_header.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add skb_gro_checksum_validate, skb_gro_checksum_validate_zero_check,
and skb_gro_checksum_simple_validate, and __skb_gro_checksum_complete.
These are the cognates of the normal checksum functions but are used
in the gro_receive path and operate on GRO related fields in sk_buffs.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace open codings of (((u64) <x> * <y>) >> 32) with reciprocal_scale().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drivers, and perhaps other entities we have not yet considered,
sometimes want to know how deep the protocol headers go before
deciding how large of an SKB to allocate and how much of the packet to
place into the linear SKB area.

For example, consider a driver which has a device which DMAs into
pools of pages and then tells the driver where the data went in the
DMA descriptor(s).  The driver can then build an SKB and reference
most of the data via SKB fragments (which are page/offset/length
triplets).

However at least some of the front of the packet should be placed into
the linear SKB area, which comes before the fragments, so that packet
processing can get at the headers efficiently.  The first thing each
protocol layer is going to do is a "pskb_may_pull()" so we might as
well aggregate as much of this as possible while we're building the
SKB in the driver.

Part of supporting this is that we don't have an SKB yet, so we want
to be able to let the flow dissector operate on a raw buffer in order
to compute the offset of the end of the headers.

So now we have a __skb_flow_dissect() which takes an explicit data
pointer and length.
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: bcm7xxx: APD and EEE support

This patch series enables Auto-power down and EEE for the BCM7xxx integrated
Gigabit PHYs.

I also put a fix for the fixed PHY that would allow clause 45 over clause 22
reads/writes but would return bogus data by using e.g: ethtool --show-eee
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.

Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Internal PHYs do not have any specific phy_interface_t defined because
they are within an Ethernet MAC or a larger IC, they will fail the early
check in phy_init_eee(). Allow these PHYs to proceed with EEE
initialization and report error/success by checking the standard C45
EEE-related registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some PHY drivers might need to access Clause 45 registers in Clause 22
compatibility mode to e.g: properly advertise EEE support when disabled
by default.

Export these two helper functions: phy_read_mmd_indirect() and
phy_write_mmd_indirect() for drivers to use them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fixed PHY driver does not properly emulate Clause 45 over Clause 22
MDIO reads, and as such, will return bogus values when we access such
registers.

Return an error when accessing these registers in order to prevent
advertising bogus capabilities such as EEE support and such.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 28nm process BCM7xxx internal Gigabit PHYs all support automatic
power down, turn on that feature as part of the configuration
initialization callback.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The shadow register 0x1C is used both by the BCM54xxx PHYs and the
BCM7xxx internal PHYs, move the accessors to a common location so both
drivers can use them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 439d39a9 ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: Merge port and socket layer code

After the removal of the TIPC native interface, there is no reason to
keep a distinction between a "generic" port layer and a "specific"
socket layer in the code. Throughout the last months, we have posted
several series that aimed at facilitating removal of the port layer,
and in particular the port_lock spinlock, which in reality duplicates
the role normally kept by lock_sock()/bh_lock_sock().

In this series, we finalize this work, by making a significant number of
changes to the link, node, port and socket code, all with the aim of
reducing dependencies between the layers. In the final commits, we then
remove the port spinlock, port.c and port.h altogether.

After this series, we have a socket layer that has only few dependencies
to the rest of the stack, so that it should be possible to continue
cleanups of its code without significantly affecting other code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We complete the merging of the port and socket layer by aggregating
the fields of struct tipc_port directly into struct tipc_sock, and
moving the combined structure into socket.c.

We also move all functions and macros that are not any longer
exposed to the rest of the stack into socket.c, and rename them
accordingly.

Despite the size of this commit, there are no functional changes.
We have only made such changes that are necessary due of the removal
of struct tipc_port.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reference table is now 'socket aware' instead of being generic,
and has in reality become a socket internal table. In order to be
able to minimize the API exposed by the socket layer towards the rest
of the stack, we now move the reference table definitions and functions
into the file socket.c, and rename the functions accordingly.

There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We move the inline functions in the file port.h to socket.c, and modify
their names accordingly.

We move struct tipc_port and some macros to socket.h.

Finally, we remove the file port.h.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In this commit, we move the remaining functions in port.c to
socket.c, and give them new names that correspond to their new
location. We then remove the file port.c.

There are only cosmetic changes to the moved functions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous commits we have reduced usage of port_lock to a minimum,
and complemented it with usage of bh_lock_sock() at the remaining
locations. The purpose has been to remove this lock altogether, since
it largely duplicates the role of bh_lock_sock. We are now ready to do
this.

However, we still need to protect the BH callers from inadvertent
release of the socket while they hold a reference to it. We do this by
replacing port_lock by a combination of a rw-lock protecting the
reference table as such, and updating the socket reference counter while
the socket is referenced from BH. This technique is more standard and
comprehensible than the previous approach, and turns out to have a
positive effect on overall performance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to make tipc_sock the only entity referencable from other
parts of the stack, we add a tipc_sock pointer instead of a tipc_port
pointer to the registry. As a consequence, we also let the function
tipc_port_lock() return a pointer to a tipc_sock instead  of a tipc_port.
We keep the function's name for now, since the lock still is owned by
the port.

This is another step in the direction of eliminating port_lock, replacing
its usage with lock_sock() and bh_lock_sock().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions tipc_port_get_ports() and tipc_port_reinit() scan over
all sockets/ports to access each of them. This is done by using a
dedicated linked list, 'tipc_socks' where all sockets are members. The
list is in turn protected by a spinlock, 'port_list_lock', while each
socket is locked by using port_lock at the moment of access.

In order to reduce complexity and risk of deadlock, we want to get
rid of the linked list and the accompanying spinlock.

This is what we do in this commit. Instead of the linked list, we use
the port registry to scan across the sockets. We also add usage of
bh_lock_sock() inside the scope of port_lock in both functions, as a
preparation for the complete removal of port_lock.

Finally, we move the functions from port.c to socket.c, and rename them
to tipc_sk_sock_show() and tipc_sk_reinit() repectively.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the latest changes to the socket/port layer the existence of
the functions tipc_port_init() and tipc_port_destroy() cannot be
justified. They are both called only once, from tipc_sk_create() and
tipc_sk_delete() respectively, and their functionality can better be
merged into the latter two functions.

This also entails that all remaining references to port_lock now are
made from inside socket.c, something that will make it easier to remove
this lock.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function tipc_acknowledge() is a remnant from the obsolete native
API. Currently, it grabs port_lock, before building an acknowledge
message and sending it to the peer.

Since all access to socket members now is protected by the socket lock,
it has become unnecessary to grab port_lock here.

In this commit, we remove the usage of port_lock, simplify the
function, and move it to socket.c, renaming it to tipc_sk_send_ack().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_port_connect()/tipc_port_disconnect() are remnants of the obsolete
native API. Their only task is to grab port_lock and call the functions
__tipc_port_connect()/__tipc_port_disconnect() respectively, which will
perform the actual state change.

Since socket/port exection now is single-threaded the use of port_lock
is not needed any more, so we can safely replace the two functions with
their lock-free counterparts.

In this commit, we remove the two functions. Furthermore, the contents
of __tipc_port_disconnect() is so trivial that we choose to eliminate
that function too, expanding its functionality into tipc_shutdown().
__tipc_port_connect() is simplified, moved to socket.c, and given the
more correct name tipc_sk_finish_conn(). Finally, we eliminate the
function auto_connect(), and expand its contents into filter_connect().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_port_shutdown() is a remnant from the now obsolete native
interface. As such it grabs port_lock in order to protect itself
from concurrent BH processing.

However, after the recent changes to the port/socket upcalls, sockets
are now basically single-threaded, and all execution, except the read-only
tipc_sk_timer(), is executing within the protection of lock_sock(). So
the use of port_lock is not needed here.

In this commit we eliminate the whole function, and merge it into its
only caller, tipc_shutdown().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The last remaining BH upcall to the socket, apart for the message
reception function tipc_sk_rcv(), is the timer function.

We prefer to let this function continue executing in BH, since it only
does read-acces to semi-permanent data, but we make three changes to it:

1) We introduce a bh_lock_sock()/bh_unlock_sock() inside the scope
   of port_lock.  This is a preparation for replacing port_lock with
   bh_lock_sock() at the locations where it is still used.

2) We move the function from port.c to socket.c, as a further step
   of eliminating the port code level altogether.

3) We let it make use of the newly introduced tipc_msg_create()
   function. This enables us to get rid of three context specific
   functions (port_create_self_abort_msg() etc.) in port.c
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current implementation, each 'struct tipc_node' instance keeps
a linked list of those ports/sockets that are connected to the node
represented by that struct. The purpose of this is to let the node
object know which sockets to alert when it loses contact with its peer
node, i.e., which sockets need to have their connections aborted.

This entails an unwanted direct reference from the node structure
back to the port/socket structure, and a need to grab port_lock
when we have to make an upcall to the port. We want to get rid of
this unecessary BH entry point into the socket, and also eliminate
its use of port_lock.

In this commit, we instead let the node struct keep list of "connected
socket" structs, which each represents a connected socket, but is
allocated independently by the node at the moment of connection. If
the node loses contact with its peer node, the list is traversed, and
a "connection abort" message is created for each entry in the list. The
message is sent to it respective connected socket using the ordinary
data path, and the receiving socket aborts its connections upon reception
of the message.

This enables us to get rid of the direct reference from 'struct node' to
´struct port', and another unwanted BH access point to the latter.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current link implementation keeps a linked list of blocked ports/
sockets that is populated when there is link congestion. The purpose
of this is to let the link know which users to wake up when the
congestion abates.

This adds unnecessary complexity to the data structure and the code,
since it forces us to involve the link each time we want to delete
a socket. It also forces us to grab the spinlock port_lock within
the scope of node_lock. We want to get rid of this direct dependence,
as well as the deadlock hazard resulting from the usage of port_lock.

In this commit, we instead let the link keep list of a "wakeup" pseudo
messages for use in such situations. Those messages are sent to the
pending sockets via the ordinary message reception path, and wake up
the socket's owner when they are received.

This enables us to get rid of the 'waiting_ports' linked lists in struct
tipc_port that manifest this direct reference. As a consequence, we can
eliminate another BH entry into the socket, and hence the need to grab
port_lock. This is a further step in our effort to remove port_lock
altogether.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function tipc_msg_init() has turned out to be of limited value
in many cases. It take too few parameters to be usable for creating
a complete message, it makes too many assumptions about what the
message should be used for, and it does not allocate any buffer to
be returned to the caller.

Therefore, we now introduce the new function tipc_msg_create(), which
takes all the parameters needed to create a full message, and returns
a buffer of the requested size. The new function will be very useful
for the changes we will be doing in later commits in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pulling to get some TIPC fixes that a net-next series depends
upon.
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon timeout, undo (via both timestamps/Eifel and DSACKs) was
disabled if any retransmits were still in flight.  The concern was
perhaps that spurious retransmission sent in a previous recovery
episode may trigger DSACKs to falsely undo the current recovery.

However, this inadvertently misses undo opportunities (using either
TCP timestamps or DSACKs) when timeout occurs during a loss episode,
i.e.  recurring timeouts or timeout during fast recovery. In these
cases some retransmissions will be in flight but we should allow
undo. Furthermore, we should only reset undo_marker and undo_retrans
upon timeout if we are starting a new recovery episode. Finally,
when we do reset our undo state, we now do so in a manner similar
to tcp_enter_recovery(), so that we require a DSACK for each of
the outstsanding retransmissions. This will achieve the original
goal by requiring that we receive the same number of DSACKs as
retransmissions.

This patch increases the undo events by 50% on Google servers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bare register numbers are used despite <uapi/linux/mdio.h> has MDIO_DEVS[12]
#define'd for those.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As a followup to commit 676d2369 ("net: Fix use after free by
removing length arg from sk_data_ready callbacks"), we can remove
some useless code in sock_queue_rcv_skb() and rxrpc_queue_rcv_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ktime_get_ns() replaces ktime_to_ns(ktime_get())

ktime_get_real_ns() replaces ktime_to_ns(ktime_get_real())
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first initializer in the following

        union vxlan_addr ipa = {
            .sin.sin_addr.s_addr = tip,
            .sa.sa_family = AF_INET,
        };

is optimised away by the compiler, due to the second initializer,
therefore initialising .sin.sin_addr.s_addr always to 0.
This results in netlink messages indicating a L3 miss never contain the
missed IP address. This was observed with GCC 4.8 and 4.9. I do not know about previous versions.
The problem affects user space programs relying on an IP address being
sent as part of a netlink message indicating a L3 miss.

Changing
            .sa.sa_family = AF_INET,
to
            .sin.sin_family = AF_INET,
fixes the problem.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can-next 2014-08-20

this is a pull request of 10 patches for net-next/master.

There is one patch by Wolfram Sang to clean up the build system.
Two patches by Stefan Agner that add vf610 support to the flexcan
driver. Dong Aisheng add support for bosch's m_can core, which is found
in the new freescale ARM SoCs. Sergei Shtylyov improves the rcar_can
driver by supporting all input clocks and adding device tree support.
The next patch is a small cleanup for the bit rate calculation function
by Lad, Prabhakar. And finally a patch by Himangi Saraogi, which
converts the mcp251x driver to use dmam_alloc_coherent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fix from Thierry Reding:
 "Just one bugfix for the PWM lookup table code that would cause a PWM
  channel to be set to the wrong period and polarity for non-perfect
  matches"

* tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: Fix period and polarity in pwm_get() for non-perfect matches

The new_ctx pointer is set only for non-chanctx drivers.  This yielded a
crash for chanctx-based drivers during channel switch finalization:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
  IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]

Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:
 "Here are some bug fixes that have piled up during ksummit/linuxcon.

   1) Fix endian problems in ibmveth, from Anton Blanchard.

   2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
      Benjamin Block.

   3) SCTP association fixes from Daniel Borkmann.

   4) When multiple VLAN headers are present we have to make sure the
      second and subsequent ones are pullable in the SKB otherwise we
      blindly dereference garbage.  From Jiri Benc.

   5) The argument adjustment of the signature of hlist_add_after*()
      introduced a regression in the batman-adv code, fix from Sven
      Eckelmann.

   6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
      Jain.

   7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.

   8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
      Chas Williams.

   9) Truncate packets larger then the TPACKET_V3 format configured
      buffers, otherwise we overwrite past the end of said buffers.
      From Eric Dumazet.

  10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
      Borundia and Shahed Shaikh.

  11) CXGB4 sometimes doesn't get all of the TX completion events it
      should resulting in SKBs getting stuck in the TX queue, from
      Hariprasad Shenai.

  12) When the FEC chip's PTP clock is disabled, you can't access the
      register.  Add necessary checks to avoid the resulting hang, from
      Fugang Duan"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
  net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
  net: sctp: spare unnecessary comparison in sctp_trans_elect_best
  net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
  ibmveth: Fix endian issues with rx_no_buffer statistic
  net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
  openvswitch: fix panic with multiple vlan headers
  net: ipv6: fib: don't sleep inside atomic lock
  net: fec: ptp: avoid register access when ipg clock is disabled
  cxgb4: Free completed tx skbs promptly
  cxgb4: Fix race condition in cleanup
  sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
  bnx2x: Revert UNDI flushing mechanism
  qlcnic: Fix endianess issue in firmware load from file operation
  qlcnic: Fix endianess issue in FW dump template header
  qlcnic: Fix flash access interface to application
  MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
  macvlan: Allow setting multicast filter on all macvlan types
  packet: handle too big packets for PACKET_V3
  MAINTAINERS: add entry for ec_bhf driver
  ...

Event timestamp status messages have a variable length, ranging from
1 to 5 words (16 bit words). The current code however requires
a minimum message length of sizeof(*phy_txts). In most cases this
condition is fulfilled due to padding bytes. However, if several events
are signaled in a single message, padding bytes may not be present.
For short event timestamp status messages, the length check will fail,
and the event timestamp will be dropped.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds fix_mac_speed() support for
Altera socfpga Ethernet controller. Emac splitter is a
soft IP core in FPGA system that converts GMII interface from
Synopsys mac to RGMII/SGMII interface. This splitter core is
an optional IP if user would like to use RGMII/SGMII
interface in their system. Software needs to update a register
in splitter core when there is speed change.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>