Don't bounce back to the root level for fragment processing, because
huge pages are not supported at that level. This is unlikely to happen
with the default VM size on Vega, but can be exposed by limiting the
VM size with the amdgpu.vm_size module parameter.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Avoid potential integer overflows with left shift in huge-page mapping
code by casting the operand to uin64_t first.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Path property is used for userspace to know what MST connector goes to what actual DRM DisplayPort connector, the tiling property is for tiling configurations. Not sure what else there is to figure out.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The change fixed huge delay in SST daisy chain and S3 soft hang
observed in 4.19 kernel rebase.

Regression point in drm:
drm/fb-helper: Eliminate the .best_encoder() usage

The aux sequence is altered due to the failure in
drm_connector_for_each_possible_encoder(). The failure is
caused by missing attached encoder in the process of adding
MST connector.
 
drm_dp_send_enum_path_resources() aux transaction is pushed after
mode probe, which causes conflict to drm_dp_mst_i2c_xfer(),
leading to the transaction timeout.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Due to the register name and setting change of HDP
memory light sleep on Vega20,change accordingly in
the driver.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Reading the sysfs files pp_sclk_od and pp_mclk_od return the
percentage difference between the VBIOS-provided default
frequency and the current (possibly user-set) frequency in
the highest SCLK and MCLK DPM states, respectively.

Writing to these files provides an easy mechanism for
setting a higher-than-default maximum frequency. We
normally only allow values >= 0 to be written here.

However, with the addition of pp_od_clk_voltage, we now
allow users to set custom DPM tables. If they then set
the maximum DPM state to something less than the default,
later reads of pp_*_od should return a negative value.
The highest DPM state is now less than the VBIOS-provided
default, so the percentage is negative.

The math to calculate this was originally performed with
unsigned values, meaning reads that should return negative
values returned meaningless data. This patch corrects that
issue and normalizes how all of the calculations are done
across the various hwmgr types.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Due to lack of MODULE_FIRMWARE() with hainan_mc.bin, the driver
doesn't work properly in initrd.  Let's add it.

Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1116239
Fixes: 8eaf2b1f ("drm/amdgpu: switch firmware path for SI parts")
Cc: <stable@vger.kernel.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Disable these features on Vega20 for now.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Feifei Xu<Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On Vega20 and other pre-production GPUs, powerplay is not enabled yet.
Check for NULL pointers before calling pp_funcs function pointers.

Also affects Kaveri.

CC: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.

Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.

This should be a user configurable option such that the user can select
what bpc configuration they would like.

[How]
This patch adds support for getting and setting the amdgpu driver
specific "max bpc" property on the connector.

It also adds support for limiting the output bpc based on the property
value. The default limitation is the lowest value in the range, 8bpc.
This was the old value before the range was uncapped.

This patch should be updated/replaced later once common drm support
for max bpc lands.

Bugzilla: https://bugs.freedesktop.org/108542
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201585
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200645
Fixes: e03fd3f3 ("drm/amd/display: Do not limit color depth to 8bpc")

v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.

Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.

This should be a user configurable option such that the user can select
what bpc configuration they would like.

[How]
This patch introduces the "max bpc" amdgpu driver specific connector
property so the user can limit the maximum bpc. It ranges from 8 to 16.

This doesn't directly set the preferred bpc for the panel since it
follows Intel's existing driver conventions.

This proprety should be removed once common drm support for max bpc
lands.

v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fixes for 4.20:
- Fix for huge page handling that caused a GPUVM fault in some cases
- Fix IH ring setup
- Fix for xgmi aperture setup
- Fix for watermark setup for SMU
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114171853.2866-1-alexander.deucher@amd.com

Cross-subsystem:
- omap: Instantiate dss children in omapdss instead of mach (Laurent)

Other:
- htmldocs build warning (Sean)
- MST NULL deref fix (Stanislav)
- omap: Various runtime ref gets on probe/bind (Laurent)
- omap: Fix to the above dss children patch (Tony)

Cc: Sean Paul <sean@poorly.run>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114204542.GA52569@art_vandelay

We accidentially set the huge flag on the parent instead of the childs.
This caused some VM faults under memory pressure.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

the clk value should be tranferred to MHz first and
then transfer to uint16. otherwise, the clock value
will be truncated.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The bug limits the IH ring wptr address to 40bit. When the system memory
is bigger than 1TB, the bus address is more than 40bit, this causes the
interrupt cannot be handled and cleared correctly.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The video mode for DMT is only populated to support encp.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1542048069-22603-1-git-send-email-jramirez@baylibre.com

In XGMI configuration, the FB region covers vram region from peer
device, adjust system aperture to cover all of them
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We're missing a call to of_platform_depopulate() on errors for dsi.
Looks like dss is already doing this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106152802.38599-1-tony@atomide.com

The internal encoders (DSI, HDMI4, HDMI5 and VENC) runtime PM handlers
attempt to manage the runtime PM state of the connected DISPC, based on
the rationale that the DISPC providing data to the encoders requires
ensuring that the display is active whenever the encoders are active.

While the DISPC provides data to the encoders, it doesn't as such
constitute a resource that encoders require in order to be taken out
of suspend, contrary to for instance a functional clock or a power
supply. Encoders registers can be accessed without the DISPC being
active, and while the encoders will not output any video stream without
being fed by the DISPC, the DISPC PM state doesn't influence the
encoders PM state.

For this reason the DISPC PM state is better managed from the omapdrm
driver, in the CRTC enable and disable operations. This allows the
encoders PM state to be handled separately from the DISPC, and in
particular at times when the DISPC may not be available (for instance at
probe due to the DSS probe being deferred, or at remove time du to the
DISPC being already removed).

Fixes: edb715df ("drm/omap: dss: dsi: Move initialization code from bind to probe")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-5-laurent.pinchart@ideasonboard.com

The probe function performs hardware access to read the number of
supported data lanes from a configuration register and thus requires the
device to be active. Ensure this by surrounding the access with
dsi_runtime_get() and dsi_runtime_put() calls.

Fixes: edb715df ("drm/omap: dss: dsi: Move initialization code from bind to probe")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-4-laurent.pinchart@ideasonboard.com

The bind function performs hardware access (in hdmi4_cec_init()) and
thus requires the device to be active. Ensure this by surrounding the
bind function by hdmi_runtime_get() and hdmi_runtime_put() calls.

Fixes: 27d62452 ("drm/omap: dss: Acquire next dssdev at probe time")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-3-laurent.pinchart@ideasonboard.com

The DSS DT node contains children that describe the DSS components
(DISPC and internal encoders). Each of those components is handled by a
platform driver, and thus needs to be backed by a platform device.

The corresponding platform devices are created in mach-omap2 code by a
call to of_platform_populate(). While this approach has worked so far,
it doesn't model the hardware architecture very well, as it creates
child devices before the parent is ready to handle them. This would be
akin to creating I2C slaves before the I2C master is available.

The task can be easily performed in the omapdss driver code instead,
simplifying mach-omap2 code. We however can't remove the mach-omap2 code
completely as the omap2fb driver still depends on it, but we can move it
to the omap2fb-specific section, where it can stay until the omap2fb
driver gets removed.

This has the added benefit of not allowing DSS components to probe
before the DSS itself, which led to runtime PM issues when the DSS probe
is deferred.

Fixes: 27d62452 ("drm/omap: dss: Acquire next dssdev at probe time")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-2-laurent.pinchart@ideasonboard.com

Pull networking fixes from David Miller:
 "One last pull request before heading to Vancouver for LPC, here we have:

   1) Don't forget to free VSI contexts during ice driver unload, from
      Victor Raj.

   2) Don't forget napi delete calls during device remove in ice driver,
      from Dave Ertman.

   3) Don't request VLAN tag insertion of ibmvnic device when SKB
      doesn't have VLAN tags at all.

   4) IPV4 frag handling code has to accomodate the situation where two
      threads try to insert the same fragment into the hash table at the
      same time. From Eric Dumazet.

   5) Relatedly, don't flow separate on protocol ports for fragmented
      frames, also from Eric Dumazet.

   6) Memory leaks in qed driver, from Denis Bolotin.

   7) Correct valid MTU range in smsc95xx driver, from Stefan Wahren.

   8) Validate cls_flower nested policies properly, from Jakub Kicinski.

   9) Clearing of stats counters in mc88e6xxx driver doesn't retain
      important bits in the G1_STATS_OP register causing the chip to
      hang. Fix from Andrew Lunn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  act_mirred: clear skb->tstamp on redirect
  net: dsa: mv88e6xxx: Fix clearing of stats counters
  tipc: fix link re-establish failure
  net: sched: cls_flower: validate nested enc_opts_policy to avoid warning
  net: mvneta: correct typo
  flow_dissector: do not dissect l4 ports for fragments
  net: qualcomm: rmnet: Fix incorrect assignment of real_dev
  net: aquantia: allow rx checksum offload configuration
  net: aquantia: invalid checksumm offload implementation
  net: aquantia: fixed enable unicast on 32 macvlan
  net: aquantia: fix potential IOMMU fault after driver unbind
  net: aquantia: synchronized flow control between mac/phy
  net: smsc95xx: Fix MTU range
  net: stmmac: Fix RX packet size > 8191
  qed: Fix potential memory corruption
  qed: Fix SPQ entries not returned to pool in error flows
  qed: Fix blocking/unlimited SPQ entries leak
  qed: Fix memory/entry leak in qed_init_sp_request()
  inet: frags: better deal with smp races
  net: hns3: bugfix for not checking return value
  ...

Merge tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix build errors in binrpm-pkg and bindeb-pkg targets

 - fix false positive matches in merge_config.sh

 - fix build version mismatch in deb-pkg target

 - fix dtbs_install handling in (bin)deb-pkg target

 - revert a commit that allows setlocalversion to write to source tree

* tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  builddeb: Fix inclusion of dtbs in debian package
  Revert "scripts/setlocalversion: git: Make -dirty check more robust"
  kbuild: deb-pkg: fix too low build version number
  kconfig: merge_config: avoid false positive matches from comment lines
  kbuild: deb-pkg: fix bindeb-pkg breakage when O= is used
  kbuild: rpm-pkg: fix binrpm-pkg breakage when O= is used

Pull btrfs fixes from David Sterba:
 "Several fixes to recent release (4.19, fixes tagged for stable) and
  other fixes"

* tag 'for-4.20-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix missing delayed iputs on unmount
  Btrfs: fix data corruption due to cloning of eof block
  Btrfs: fix infinite loop on inode eviction after deduplication of eof block
  Btrfs: fix deadlock on tree root leaf when finding free extent
  btrfs: avoid link error with CONFIG_NO_AUTO_INLINE
  btrfs: tree-checker: Fix misleading group system information
  Btrfs: fix missing data checksums after a ranged fsync (msync)
  btrfs: fix pinned underflow after transaction aborted
  Btrfs: fix cur_offset in the error case for nocow

Pull ext4 fixes from Ted Ts'o:
 "A large number of ext4 bug fixes, mostly buffer and memory leaks on
  error return cleanup paths"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: missing !bh check in ext4_xattr_inode_write()
  ext4: fix buffer leak in __ext4_read_dirblock() on error path
  ext4: fix buffer leak in ext4_expand_extra_isize_ea() on error path
  ext4: fix buffer leak in ext4_xattr_move_to_block() on error path
  ext4: release bs.bh before re-using in ext4_xattr_block_find()
  ext4: fix buffer leak in ext4_xattr_get_block() on error path
  ext4: fix possible leak of s_journal_flag_rwsem in error path
  ext4: fix possible leak of sbi->s_group_desc_leak in error path
  ext4: remove unneeded brelse call in ext4_xattr_inode_update_ref()
  ext4: avoid possible double brelse() in add_new_gdb() on error path
  ext4: avoid buffer leak in ext4_orphan_add() after prior errors
  ext4: avoid buffer leak on shutdown in ext4_mark_iloc_dirty()
  ext4: fix possible inode leak in the retry loop of ext4_resize_fs()
  ext4: fix missing cleanup if ext4_alloc_flex_bg_array() fails while resizing
  ext4: add missing brelse() update_backups()'s error path
  ext4: add missing brelse() add_new_gdb_meta_bg()'s error path
  ext4: add missing brelse() in set_flexbg_block_bitmap()'s error path
  ext4: avoid potential extra brelse in setup_new_flex_group_blocks()

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes:

   - Cure the LDT remapping to user space on 5 level paging which ended
     up in the KASLR space

   - Remove LDT mapping before freeing the LDT pages

   - Make NFIT MCE handling more robust

   - Unbreak the VSMP build by removing the dependency on paravirt ops

   - Support broken PIT emulation on Microsoft hyperV

   - Don't trace vmware_sched_clock() to avoid tracer recursion

   - Remove -pipe from KBUILD CFLAGS which breaks clang and is also
     slower on GCC

   - Trivial coding style and typo fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu/vmware: Do not trace vmware_sched_clock()
  x86/vsmp: Remove dependency on pv_irq_ops
  x86/ldt: Remove unused variable in map_ldt_struct()
  x86/ldt: Unmap PTEs for the slot before freeing LDT pages
  x86/mm: Move LDT remap out of KASLR region on 5-level paging
  acpi/nfit, x86/mce: Validate a MCE's address before using it
  acpi/nfit, x86/mce: Handle only uncorrectable machine checks
  x86/build: Remove -pipe from KBUILD_CFLAGS
  x86/hyper-v: Fix indentation in hv_do_fast_hypercall16()
  Documentation/x86: Fix typo in zero-page.txt
  x86/hyper-v: Enable PIT shutdown quirk
  clockevents/drivers/i8253: Add support for PIT shutdown quirk

Pull perf fixes from Thomas Gleixner:
 "A bunch of perf tooling fixes:

   - Make the Intel PT SQL viewer more robust

   - Make the Intel PT debug log more useful

   - Support weak groups in perf record so it's behaving the same way as
     perf stat

   - Display the LBR stats in callchain entries properly in perf top

   - Handle different PMu names with common prefix properlin in pert
     stat

   - Start syscall augmenting in perf trace. Preparation for
     architecture independent eBPF instrumentation of syscalls.

   - Fix build breakage in JVMTI perf lib

   - Fix arm64 tools build failure wrt smp_load_{acquire,release}"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Do not zero sample_id_all for group members
  perf tools: Fix undefined symbol scnprintf in libperf-jvmti.so
  perf beauty: Use SRCARCH, ARCH=x86_64 must map to "x86" to find the headers
  perf intel-pt: Add MTC and CYC timestamps to debug log
  perf intel-pt: Add more event information to debug log
  perf scripts python: exported-sql-viewer.py: Fix table find when table re-ordered
  perf scripts python: exported-sql-viewer.py: Add help window
  perf scripts python: exported-sql-viewer.py: Add Selected branches report
  perf scripts python: exported-sql-viewer.py: Fall back to /usr/local/lib/libxed.so
  perf top: Display the LBR stats in callchain entry
  perf stat: Handle different PMU names with common prefix
  perf record: Support weak groups
  perf evlist: Move perf_evsel__reset_weak_group into evlist
  perf augmented_syscalls: Start collecting pathnames in the BPF program
  perf trace: Fix setting of augmented payload when using eBPF + raw_syscalls
  perf trace: When augmenting raw_syscalls plug raw_syscalls:sys_exit too
  perf examples bpf: Start augmenting raw_syscalls:sys_{start,exit}
  tools headers barrier: Fix arm64 tools build failure wrt smp_load_{acquire,release}

Pull timer fix from Thomas Gleixner:
 "Just the removal of a redundant call into the sched deadline overrun
  check"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Remove useless call to check_dl_overrun()

Pull scheduler fixes from Thomas Gleixner:
 "Two small scheduler fixes:

   - Take hotplug lock in sched_init_smp(). Technically not really
     required, but lockdep will complain other.

   - Trivial comment fix in sched/fair"

* 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix a comment in task_numa_fault()
  sched/core: Take the hotplug lock in sched_init_smp()

Pull locking build fix from Thomas Gleixner:
 "A single fix for a build fail with CONFIG_PROFILE_ALL_BRANCHES=y in
  the qspinlock code"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/qspinlock: Fix compile error

Pull core fixes from Thomas Gleixner:
 "A couple of fixlets for the core:

   - Kernel doc function documentation fixes

   - Missing prototypes for weak watchdog functions"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  resource/docs: Complete kernel-doc style function documentation
  watchdog/core: Add missing prototypes for weak functions
  resource/docs: Fix new kernel-doc warnings

If sch_fq is used at ingress, skbs that might have been
timestamped by net_timestamp_set() if a packet capture
is requesting timestamps could be delayed by arbitrary
amount of time, since sch_fq time base is MONOTONIC.

Fix this problem by moving code from sch_netem.c to act_mirred.c.

Fixes: fb420d5d ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fc ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.

The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.

If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.

However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.

We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.

Fixes: 7ea817f4 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 37c8a5fa ("kbuild: consolidate Devicetree dtb build rules")
moved the location of 'dtbs_install' target which caused dtbs to not be
installed when building debian package with 'bindeb-pkg' target. Update
the builddeb script to use the same logic that determines if there's a
'dtbs_install' target which is presence of the arch dts directory. Also,
use CONFIG_OF_EARLY_FLATTREE instead of CONFIG_OF as that's a better
indication of whether we are building dtbs.

This commit will also have the side effect of installing dtbs on any
arch that has dts files. Previously, it was dependent on whether the
arch defined 'dtbs_install'.

Fixes: 37c8a5fa ("kbuild: consolidate Devicetree dtb build rules")
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This reverts commit 6147b1cf.

The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.

Output from "strace git status -uno --porcelain":

getcwd("/tmp/linux-test", 129)          = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
	-1 EROFS (Read-only file system)

While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.

Fixes: 6147b1cf ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since commit b41d920a ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.

Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.

Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.

Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.

Fixes: b41d920a ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>