The Micrel ksz9021 PHY does not support standard IEEE standard MMD
extended register access, therefore requires stubs to fail the read
register method and do nothing for the write register method when
libphy attempts to read and/or configure Energy Efficient Ethernet
features in PHYS that do support those features. This problem
was observed on an Altera Cyclone V SOC development kit that
uses the Synopsys EMAC and the Micrel ksz9021 PHY. This patch
was tested on the same board, and Energy Efficient Ethernet is
now disabled as expected since the Micrel PHY does not support that
feature.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

libphy was originally written assuming all phy devices support clause 45
access extensions to the mmd registers through the indirection registers
located within the first 16 phy registers. This assumption is not true
in all cases, and one specific example is the Micrel ksz9021 10/100/1000
Mbps phy. Using the stmmac driver, accessing the mmd registers to query
and configure energy efficient Ethernet (EEE) features yielded unexpected
behavior.

This patch adds mmd access functions to the phy driver that can be
overriden by the phy specific driver if the phy does not support this
mechanism or uses it's own non-standard access mechanism. By default,
the IEEE Compatible clause 45 access mechanism described in clause 22
is used. With this patch, EEE query/configure functions as expected
using the stmmac and the Micrel ksz9021 phy.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix one misspelled word reported by codespell.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_unattached_filter_destroy() does not always need to release the
filter object via rcu. Since this filter is never attached to the
socket, the caller should be responsible for releasing the filter
in a safe way, which may not necessarily imply rcu.

This is a short summary of clients of this function:

1) xt_bpf.c and cls_bpf.c use the bpf matchers from rules, these rules
   are removed from the packet path before the filter is released. Thus,
   the framework makes sure the filter is safely removed.

2) In the ppp driver, the ppp_lock ensures serialization between the
   xmit and filter attachment/detachment path. This doesn't use rcu
   so deferred release via rcu makes no sense.

3) In the isdn/ppp driver, it is called from isdn_ppp_release()
   the isdn_ppp_ioctl(). This driver uses mutex and spinlocks, no rcu.
   Thus, deferred rcu makes no sense to me either, the deferred releases
   may be just masking the effects of wrong locking strategy, which
   should be fixed in the driver itself.

4) In the team driver, this is the only place where the rcu
   synchronization with unattached filter is used. Therefore, this
   patch introduces synchronize_rcu() which is called from the
   genetlink path to make sure the filter doesn't go away while packets
   are still walking over it. I think we can revisit this once struct
   bpf_prog (that only wraps specific bpf code bits) is in place, then
   add some specific struct rcu_head in the scope of the team driver if
   Jiri thinks this is needed.

Deferred rcu release for unattached filters was originally introduced
in 302d6637 ("filter: Allow to create sk-unattached filters").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This structure is not exposed to userspace, so fix this by defining
struct sk_filter; so we skip the casting in kernelspace. This is safe
since userspace has no way to lurk with that internal pointer.

Fixes: e6f30c73 ("netfilter: x_tables: add xt_bpf match")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct typo in the name of the type given to sizeof.  Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.

This problem was found using Coccinelle (http://coccinelle.lip6.fr/).  The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver update 2014-07-25

This patch series is dependent on the following patch that was
applied to the net tree and needs to be applied to the net-next
tree:
  332cfc82 - amd-xgbe: Fix error return code in xgbe_probe()

The following series of patches includes fixes and new support in the
driver.

- Device bindings documentation update
- Hardware timestamp support
- 2.5GbE support changes
- Fifo sizes based on active queues/rings
- Phylib driver updates for:
  - Rate change completion check
  - KR training initiation
  - Auto-negotiation results
- Traffic class support, including DCB support

This patch series is based on net-next.

Changes in V2:
  - Remove DBGPR(...., __func__) calls
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for traffic classes as well as support
for Data Center Bridging interfaces related to traffic classes
and priority flow control.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a netdev_info statement detailing whether auto-negotiation was
completed through parallel detection or through the auto-negotiation
protocol.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of changing rates to KR mode, KR training is initiated. If
the KR training is restarted it is possible to enter an invalid logic
state. This can be avoided by asserting a training reset bit before
initiating the KR training and then clearing the training reset bit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the logic will loop endlessly waiting for a rate change
to complete.  Add a counter so that if the rate change signals
never indicate complete the loop will eventually exit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting the fifo sizes for the queues and enabling the queues
use the number of active Tx and Rx queues that have been enabled
not the maximum number available.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for Tx and Rx hardware timestamping.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An earlier patch added support for the "dma-coherent" device property.
This patch adds this optional property to the amd-xgbe device bindings
documentation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need for the unlikely(), WARN_ON() and BUG_ON() internally use
unlikely() on the condition.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current explanation of dcb_app->priority is wrong. It says priority is
expected to be a 3-bit unsigned integer which is only true when working with
DCBx-IEEE. Use of dcb_app->priority by DCBx-CEE expects it to be 802.1p user
priority bitmap. Updated accordingly

This affects the cxgb4 driver, but I will post those changes as part of a
larger changeset shortly.

Fixes: 3e29027a ("dcbnl: add support for ieee8021Qaz attributes")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eli Cohen says:

====================
mlx5 driver changes related to PCI handling ***

The first of these patches is changing the pci device driver from mlx5_ib to
mlx5_core in a similar manner it is done in mlx4. This set the grounds for us
to introduce Ethernet driver for HW which uses mlx5.

The other two patches contain minor fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the event flow, we currently pass only a port number in the
void *data argument.  Rather than pass a pointer to the event handlers,
we should use an "unsigned long" parameter, and pass the port number
value directly.

In the future, if necessary for some events, we can use the unsigned long
parameter to pass a pointer.

Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There were many places where parameters which should be u8/u16 were
integer type.

Additionally, in 2 places, a check for a non-null pointer was added
before dereferencing the pointer (this is actually a bug fix).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for a new mlx5 device which is VPI (i.e., ports can be
either IB or ETH), move the pci device functionality from mlx5_ib
to mlx5_core.

This involves the following changes:
1. Move mlx5_core_dev struct out of mlx5_ib_dev. mlx5_core_dev
   is now an independent structure maintained by mlx5_core.
   mlx5_ib_dev now has a pointer to that struct.
   This requires changing a lot of places where the core_dev
   struct was accessed via mlx5_ib_dev (now, this needs to
   be a pointer dereference).
2. All PCI initializations are now done in mlx5_core. Thus,
   it is now mlx5_core which does pci_register_device (and not
   mlx5_ib, as was previously).
3. mlx5_ib now registers itself with mlx5_core as an "interface"
   driver. This is very similar to the mechanism employed for
   the mlx4 (ConnectX) driver. Once the HCA is initialized
   (by mlx5_core), it invokes the interface drivers to do
   their initializations.
4. There is a new event handler which the core registers:
   mlx5_core_event(). This event handler invokes the
   event handlers registered by the interfaces.

Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we have a 3-stage seeding process in prandom():

Phase 1 is from the early actual initialization of prandom()
subsystem which happens during core_initcall() and remains
most likely until the beginning of late_initcall() phase.
Here, the system might not have enough entropy available
for seeding with strong randomness from the random driver.
That means, we currently have a 32bit weak LCG() seeding
the PRNG status register 1 and mixing that successively
into the other 3 registers just to get it up and running.

Phase 2 starts with late_initcall() phase resp. when the
random driver has initialized its non-blocking pool with
enough entropy. At that time, we throw away *all* inner
state from its 4 registers and do a full reseed with strong
randomness.

Phase 3 starts right after that and does a periodic reseed
with random slack of status register 1 by a strong random
source again.

A problem in phase 1 is that during bootup data structures
can be initialized, e.g. on module load time, and thus access
a weakly seeded prandom and are never changed for the rest
of their live-time, thus carrying along the results from a
week seed. Lets make sure that current but also future users
access a possibly better early seeded prandom.

This patch therefore improves phase 1 by trying to make it
more 'unpredictable' through mixing in seed from a possible
hardware source. Now, the mix-in xors inner state with the
outcome of either of the two functions arch_get_random_{,seed}_int(),
preferably arch_get_random_seed_int() as it likely represents
a non-deterministic random bit generator in hw rather than
a cryptographically secure PRNG in hw. However, not all might
have the first one, so we use the PRNG as a fallback if
available. As we xor the seed into the current state, the
worst case would be that a hardware source could be unverifiable
compromised or backdoored. In that case nevertheless it
would be as good as our original early seeding function
prandom_seed_very_weak() since we mix through xor which is
entropy preserving.

Joint work with Daniel Borkmann.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Pull Exynos platform DT fix from Grant Likely:
 "Device tree Exynos bug fix for v3.16-rc7

  This bug fix has been brewing for a while.  I hate sending it to you
  so late, but I only got confirmation that it solves the problem this
  past weekend.  The diff looks big for a bug fix, but the majority of
  it is only executed in the Exynos quirk case.  Unfortunately it
  required splitting early_init_dt_scan() in two and adding quirk
  handling in the middle of it on ARM.

  Exynos has buggy firmware that puts bad data into the memory node.
  Commit 1c2f87c2 ("ARM: Get rid of meminfo") exposed the bug by
  dropping the artificial upper bound on the number of memory banks that
  can be added.  Exynos fails to boot after that commit.  This branch
  fixes it by splitting the early DT parse function and inserting a
  fixup hook.  Exynos uses the hook to correct the DT before parsing
  memory regions"

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
  arm: Add devicetree fixup machine function
  of: Add memory limiting function for flattened devicetrees
  of: Split early_init_dt_scan into two parts

Pull Xen fix from David Vrabel:
 "Fix BUG when trying to expand the grant table.  This seems to occur
  often during boot with Ubuntu 14.04 PV guests"

* tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  x86/xen: safely map and unmap grant frames when in atomic context

Pull KVM fix from Paolo Bonzini:
 "Fix a bug which allows KVM guests to bring down the entire system on
  some 64K enabled ARM64 hosts"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: arm64: vgic: fix hyp panic with 64k pages on juno platform

This reverts commit 20fbe3ae.

As reported by Stephen Rothwell, it causes compile failures in certain
configurations:

  drivers/net/usb/cdc_subset.c:360:15: error: 'dummy_prereset' undeclared here (not in a function)
    .pre_reset = dummy_prereset,
                 ^
  drivers/net/usb/cdc_subset.c:361:16: error: 'dummy_postreset' undeclared here (not in a function)
    .post_reset = dummy_postreset,
                  ^
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David Miller <davem@davemloft.net>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Make fragmentation IDs less predictable, from Eric Dumazet.

 2) TSO tunneling can crash in bnx2x driver, fix from Dmitry Kravkov.

 3) Don't allow NULL msg->msg_name just because msg->msg_namelen is
    non-zero, from Andrey Ryabinin.

 4) ndm->ndm_type set using wrong macros, from Jun Zhao.

 5) cdc-ether devices can come up with entries in their address filter,
    so explicitly clear the filter after the device initializes.  From
    Oliver Neukum.

 6) Forgotten refcount bump in xfrm_lookup(), from Steffen Klassert.

 7) Short packets not padded properly, exposing random data, in bcmgenet
    driver.  Fix from Florian Fainelli.

 8) xgbe_probe() doesn't return an error code, but rather zero, when
    netif_set_real_num_tx_queues() fails.  Fix from Wei Yongjun.

 9) USB speed not probed properly in r8152 driver, from Hayes Wang.

10) Transmit logic choosing the outgoing port in the sunvnet driver
    needs to consider a) is the port actually up and b) whether it is a
    switch port.  Fix from David L Stevens.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
  net: phy: re-apply PHY fixups during phy_register_device
  cdc-ether: clean packet filter upon probe
  cdc_subset: deal with a device that needs reset for timeout
  net: sendmsg: fix NULL pointer dereference
  isdn/bas_gigaset: fix a leak on failure path in gigaset_probe()
  ip: make IP identifiers less predictable
  neighbour : fix ndm_type type error issue
  sunvnet: only use connected ports when sending
  can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()
  bnx2x: fix crash during TSO tunneling
  r8152: fix the checking of the usb speed
  net: phy: Ensure the MDIO bus module is held
  net: phy: Set the driver when registering an MDIO bus device
  bnx2x: fix set_setting for some PHYs
  hyperv: Fix error return code in netvsc_init_buf()
  amd-xgbe: Fix error return code in xgbe_probe()
  ath9k: fix aggregation session lockup
  net: bcmgenet: correctly pad short packets
  net: sctp: inherit auth_capable on INIT collisions
  mac80211: fix crash on getting sta info with uninitialized rate control
  ...

arch_gnttab_map_frames() and arch_gnttab_unmap_frames() are called in
atomic context but were calling alloc_vm_area() which might sleep.

Also, if a driver attempts to allocate a grant ref from an interrupt
and the table needs expanding, then the CPU may already by in lazy MMU
mode and apply_to_page_range() will BUG when it tries to re-enable
lazy MMU mode.

These two functions are only used in PV guests.

Introduce arch_gnttab_init() to allocates the virtual address space in
advance.

Avoid the use of apply_to_page_range() by using saving and using the
array of PTE addresses from the alloc_vm_area() call (which ensures
that the required page tables are pre-allocated).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

If the physical address of GICV isn't page-aligned, then we end up
creating a stage-2 mapping of the page containing it, which causes us to
map neighbouring memory locations directly into the guest.

As an example, consider a platform with GICV at physical 0x2c02f000
running a 64k-page host kernel. If qemu maps this into the guest at
0x80010000, then guest physical addresses 0x80010000 - 0x8001efff will
map host physical region 0x2c020000 - 0x2c02efff. Accesses to these
physical regions may cause UNPREDICTABLE behaviour, for example, on the
Juno platform this will cause an SError exception to EL3, which brings
down the entire physical CPU resulting in RCU stalls / HYP panics / host
crashing / wasted weeks of debugging.

SBSA recommends that systems alias the 4k GICV across the bounding 64k
region, in which case GICV physical could be described as 0x2c020000 in
the above scenario.

This patch fixes the problem by failing the vgic probe if the physical
base address or the size of GICV aren't page-aligned. Note that this
generated a warning in dmesg about freeing enabled IRQs, so I had to
move the IRQ enabling later in the probe.

Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Joel Schopp <joel.schopp@amd.com>
Cc: Don Dutile <ddutile@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Joel Schopp <joel.schopp@amd.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Commit 1c2f87c2
(ARM: 8025/1: Get rid of meminfo) dropped the upper bound on
the number of memory banks that can be added as there was no
technical need in the kernel. It turns out though, some bootloaders
(specifically the arndale-octa exynos boards) may pass invalid memory
information and rely on the kernel to not parse this data. This is a
bug in the bootloader but we still need to work around this.
Work around this by introducing a dt_fixup function. This function
gets called before the flattened devicetree is scanned for memory
and the like. In this fixup function for exynos, limit the maximum
number of memory regions in the devicetree.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Andreas Färber <afaerber@suse.de>
[glikely: Added a comment and fixed up function name]
Signed-off-by: Grant Likely <grant.likely@linaro.org>

Buggy bootloaders may pass bogus memory entries in the devicetree.
Add of_fdt_limit_memory to add an upper bound on the number of
entries that can be present in the devicetree.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

Currently, early_init_dt_scan validates the header, sets the
boot params, and scans for chosen/memory all in one function.
Split this up into two separate functions (validation/setting
boot params in one, scanning in another) to allow for
additional setup between boot params and scanning the memory.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Andreas Färber <afaerber@suse.de>
[glikely: s/early_init_dt_scan_all/early_init_dt_scan_nodes/]
Signed-off-by: Grant Likely <grant.likely@linaro.org>

This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit is similar to commit 4d12bc63 ("net: mvneta: fix
operation in 10 Mbit/s mode"), but this time for the mvpp2 driver. The
driver was properly taking into account the 1 Gbit/s and 100 Mbit/s
speeds, but not the 10 Mbit/s, which was handled as 100
Mbit/s. However, the MVPP2_GMAC_CONFIG_MII_SPEED bit in the
MVPP2_GMAC_AUTONEG_CONFIG register must remain cleared to allow 10
Mbit/s operation. This commit therefore fixes 10 Mbit/s operation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse warns because of implicit pointer cast.

v2: subject line correction, space between "void" and "*"
Signed-off-by: Karoly Kemeny <karoly.kemeny@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the use of the macro IS_ERR_OR_NULL in place of
tests for NULL and IS_ERR.

The following Coccinelle semantic patch was used for making the change:

@@
expression e;
@@

- e == NULL || IS_ERR(e)
+ IS_ERR_OR_NULL(e)
 || ...
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>