The first thing we want to do is just read the module revision register to
be able to configure the module specific quirks and configure the module
registers.

As the interconnect target module may not yet be properly configured and
may need a reset first, we don't want to use pm_runtime_get() at this
point.

To read the revision register, let's just enable the all the clocks for
the interconnect target module during init even if the optional clocks
are not needed. That way we can read the revision register to configure
the quirks needed for PM runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>

At least McPDM module depends on an external optional clock to be
usable. To make handling of the McPDM clock easier in the following
patches, let's add separate functions for handling the main clocks
and the optional clocks.

Let's also add error handling to shut down already enabled clocks
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Let's move the legacy idle and enable into separate functions to simplify
PM runtime functions a bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can make sysc_write() and sysc_child_pm_domain static as noted by
sparse.
Signed-off-by: Tony Lindgren <tony@atomide.com>

We have ti,no-idle in use in addition to ti,no-idle-on-init but we're
missing handling for it in the ti-sysc interconnect target module driver.

Let's also group the idle defines together and update the binding
documentation for it.

Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

If we return early before ddata->clocks have been allocated we will get a
NULL pointer dereference in sysc_unprepare(). Let's fix this by returning
early when no clocks are allocated.

Fixes: 0eecc636 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>

For dynamically allocated struct omap_hwmod data, we need to populate
the device IP specific reset quirks.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can just check for omap2 and 3 for i2c and smartreflex locally.
The rest of the .rev data is already unused.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With ti-sysc interconnect target module, we can allocate struct omap_hwmod
data based on the devicetree data. This allows dropping the static SoC
specific data eventually so we will only boot with data we actually need.

To allocate struct omap_hwmod dynamically, we need to add a mutex for
modifying the list, and remove __init for few functions.

Note that we are not initialized oh->_clk or the optional clocks and their
related quirks. That can be directly handled by the interconnect target
module driver.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For dynamically allocated struct hwmod entries probing with ti-sysc
interconnect target module driver, we need to specify the initial default
state the same way as we do for the platform data cases.

Let's prepare for that by adding _HWMOD_STATE_DEFAULT that we can then
use to set the initial default state without a need to add similar
CONFIG_PM handling in multiple places.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For dynamically allocated sysconfig data we only need to allocate a new
class for the cases where the class is shared. For dynamically allocated
struct omap_hwmod we will always allocate a new class.

Let's add detection for when we need to allocate a new class by comparing
the class name against the module name. If they match, there's no need
to allocate a new calls as we don't have case of mixed platform data and
dts data initialized modules for the same class.

Let's also move the init of class data inside the spinlock.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Only omap_hwmod_init_module() gets called, the rest of the interconnect
target module allocation functions can be static.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 747834ab ("ARM: OMAP2+: hwmod: revise hardreset behavior") made
the call to _enable() conditional based on no oh->rst_lines_cnt. This
caused the return value to be potentially uninitialized. Curiously we see
no compiler warnings for this, probably as this gets inlined.

We call _setup_reset() from _setup() and only _setup_postsetup() if the
return value is zero. Currently the return value can be uninitialized for
cases where oh->rst_lines_cnt is set and HWMOD_INIT_NO_RESET is not set.

Fixes: 747834ab ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We must not use legacy clock defines for dts clckctrl clocks as the offsets
will be wrong.

Fixes: 87fc89ce ("ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc")
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull more Kbuild updates from Masahiro Yamada:

 - add more Build-Depends to Debian source package

 - prefix header search paths with $(srctree)/

 - make modpost show verbose section mismatch warnings

 - avoid hard-coded CROSS_COMPILE for h8300

 - fix regression for Debian make-kpkg command

 - add semantic patch to detect missing put_device()

 - fix some warnings of 'make deb-pkg'

 - optimize NOSTDINC_FLAGS evaluation

 - add warnings about redundant generic-y

 - clean up Makefiles and scripts

* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove stale lxdialog/.gitignore
  kbuild: force all architectures except um to include mandatory-y
  kbuild: warn redundant generic-y
  Revert "modsign: Abort modules_install when signing fails"
  kbuild: Make NOSTDINC_FLAGS a simply expanded variable
  kbuild: deb-pkg: avoid implicit effects
  coccinelle: semantic code search for missing put_device()
  kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
  kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
  kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
  kbuild: add workaround for Debian make-kpkg
  kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
  unicore32: simplify linker script generation for decompressor
  h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
  kbuild: move archive command to scripts/Makefile.lib
  modpost: always show verbose warning for section mismatch
  ia64: prefix header search path with $(srctree)/
  libfdt: prefix header search paths with $(srctree)/
  deb-pkg: generate correct build dependencies

Pull x86 asm updates from Thomas Gleixner:
 "Two cleanup patches removing dead conditionals and unused code"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Remove unused __constant_c_x_memset() macro and inlines
  x86/asm: Remove dead __GNUC__ conditionals

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the fallout from the TSX errata workaround:

   - Prevent memory corruption caused by a unchecked out of bound array
     index.

   - Two trivial fixes to address compiler warnings"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
  perf/x86: Fixup typo in stub functions
  perf/x86/intel: Fix memory corruption

Pull xen fix from Juergen Gross:
 "A fix for a Xen bug introduced by David's series for excluding
  ballooned pages in vmcores"

* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: Fix mapping PG_offline pages to user space

Pull 9p updates from Dominique Martinet:
 "Here is a 9p update for 5.1; there honestly hasn't been much.

  Two fixes (leak on invalid mount argument and possible deadlock on
  i_size update on 32bit smp) and a fall-through warning cleanup"

* tag '9p-for-5.1' of git://github.com/martinetd/linux:
  9p/net: fix memory leak in p9_client_create
  9p: use inode->i_lock to protect i_size_write() under 32-bit
  9p: mark expected switch fall-through

Fixes: 400816f6 ("perf/x86/intel: Implement support for TSX Force Abort")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: kbuild-all@01.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190313184243.GA10820@lkp-sb-ep06

When this .gitignore was added, lxdialog was an independent hostprogs-y.

Now that all objects in lxdialog/ are directly linked to mconf, the
lxdialog is no longer generated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.

um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The generic-y is redundant under the following condition:

 - arch has its own implementation

 - the same header is added to generated-y

 - the same header is added to mandatory-y

If a redundant generic-y is found, the warning like follows is displayed:

  scripts/Makefile.asm-generic:20: redundant generic-y found in arch/arm/include/asm/Kbuild: timex.h

I fixed up arch Kbuild files found by this.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This reverts commit caf6fe91.

The commit was fine but is no longer needed as of commit 3a2429e1
("kbuild: change if_changed_rule for multi-line recipe").  Let's go
back to using ";" to be consistent.

For some discussion, see:

https://lkml.kernel.org/r/CAK7LNASde0Q9S5GKeQiWhArfER4S4wL1=R_FW8q0++_X3T5=hQ@mail.gmail.comSigned-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

During a simple no-op (nothing changed) build I saw 39 invocations of
the C compiler with the argument "-print-file-name=include".  We don't
need to call the C compiler 39 times for this--one time will suffice.

Let's change NOSTDINC_FLAGS to a simply expanded variable to avoid
this since there doesn't appear to be any reason it should be
recursively expanded.

On my build this shaved ~400 ms off my "no-op" build.

Note that the recursive expansion seems to date back to the (really
old) commit e8f5bdb0 ("[PATCH] Makefile include path ordering").
It's a little unclear to me if the point of that patch was to switch
the variable to be recursively expanded (which it did) or to avoid
directly assigning to NOSTDINC_FLAGS (AKA to switch to +=) because
someone else (out of tree?) was setting it.  I presume later since if
the only goal was to switch to recursive expansion the patch would
have just removed the ":".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

* The man page for dpkg-source(1) notes:

>      -b, --build directory [format-specific-parameters]
>             Build  a  source  package  (--build since dpkg 1.17.14).
>             <...>
>
>             dpkg-source will build the source package with the first
>             format found in this ordered list: the format  indicated
>             with  the  --format  command  line  option,  the  format
>             indicated in debian/source/format, “1.0”.  The  fallback
>             to “1.0” is deprecated and will be removed at some point
>             in the future, you should always  document  the  desired
>             source   format  in  debian/source/format.  See  section
>             SOURCE PACKAGE FORMATS for an extensive  description  of
>             the various source package formats.

  Thus it would be more foolproof to explicitly use 1.0 (as we always
  did) than to rely on dpkg-source's defaults.

* In a similar vein, debian/rules is not made executable by mkdebian,
  and dpkg-source warns about that but still silently fixes the file.
  Let's be explicit once again.
Signed-off-by: Arseny Maslennikov <ar@cs.msu.ru>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
The implementation of this semantic code search is:
In a function, for a local variable returned by calling
of_find_device_by_node(),
a, if it is released by a function such as
   put_device()/of_dev_put()/platform_device_put() after the last use,
   it is considered that there is no reference leak;
b, if it is passed back to the caller via
   dev_get_drvdata()/platform_get_drvdata()/get_device(), etc., the
   reference will be released in other functions, and the current function
   also considers that there is no reference leak;
c, for the rest of the situation, the current function should release the
   reference by calling put_device, this code search will report the
   corresponding error message.

By using this semantic code search, we have found some object reference leaks,
such as:
commit 11907e9d ("ASoC: fsl-asoc-card: fix object reference leaks in
fsl_asoc_card_probe")
commit a12085d1 ("mtd: rawnand: atmel: fix possible object reference leak")
commit 11493f26 ("mtd: rawnand: jz4780: fix possible object reference leak")

There are still dozens of reference leaks in the current kernel code.

Further, for the case of b, the object returned to other functions may also
have a reference leak, we will continue to develop other cocci scripts to
further check the reference leak.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Pull pidfd system call from Christian Brauner:
 "This introduces the ability to use file descriptors from /proc/<pid>/
  as stable handles on struct pid. Even if a pid is recycled the handle
  will not change. For a start these fds can be used to send signals to
  the processes they refer to.

  With the ability to use /proc/<pid> fds as stable handles on struct
  pid we can fix a long-standing issue where after a process has exited
  its pid can be reused by another process. If a caller sends a signal
  to a reused pid it will end up signaling the wrong process.

  With this patchset we enable a variety of use cases. One obvious
  example is that we can now safely delegate an important part of
  process management - sending signals - to processes other than the
  parent of a given process by sending file descriptors around via scm
  rights and not fearing that the given process will have been recycled
  in the meantime. It also allows for easy testing whether a given
  process is still alive or not by sending signal 0 to a pidfd which is
  quite handy.

  There has been some interest in this feature e.g. from systems
  management (systemd, glibc) and container managers. I have requested
  and gotten comments from glibc to make sure that this syscall is
  suitable for their needs as well. In the future I expect it to take on
  most other pid-based signal syscalls. But such features are left for
  the future once they are needed.

  This has been sitting in linux-next for quite a while and has not
  caused any issues. It comes with selftests which verify basic
  functionality and also test that a recycled pid cannot be signaled via
  a pidfd.

  Jon has written about a prior version of this patchset. It should
  cover the basic functionality since not a lot has changed since then:

      https://lwn.net/Articles/773459/

  The commit message for the syscall itself is extensively documenting
  the syscall, including it's functionality and extensibility"

* tag 'pidfd-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  selftests: add tests for pidfd_send_signal()
  signal: add pidfd_send_signal() syscall

Pull device-dax updates from Dan Williams:
 "New device-dax infrastructure to allow persistent memory and other
  "reserved" / performance differentiated memories, to be assigned to
  the core-mm as "System RAM".

  Some users want to use persistent memory as additional volatile
  memory. They are willing to cope with potential performance
  differences, for example between DRAM and 3D Xpoint, and want to use
  typical Linux memory management apis rather than a userspace memory
  allocator layered over an mmap() of a dax file. The administration
  model is to decide how much Persistent Memory (pmem) to use as System
  RAM, create a device-dax-mode namespace of that size, and then assign
  it to the core-mm. The rationale for device-dax is that it is a
  generic memory-mapping driver that can be layered over any "special
  purpose" memory, not just pmem. On subsequent boots udev rules can be
  used to restore the memory assignment.

  One implication of using pmem as RAM is that mlock() no longer keeps
  data off persistent media. For this reason it is recommended to enable
  NVDIMM Security (previously merged for 5.0) to encrypt pmem contents
  at rest. We considered making this recommendation an actively enforced
  requirement, but in the end decided to leave it as a distribution /
  administrator policy to allow for emulation and test environments that
  lack security capable NVDIMMs.

  Summary:

   - Replace the /sys/class/dax device model with /sys/bus/dax, and
     include a compat driver so distributions can opt-in to the new ABI.

   - Allow for an alternative driver for the device-dax address-range

   - Introduce the 'kmem' driver to hotplug / assign a device-dax
     address-range to the core-mm.

   - Arrange for the device-dax target-node to be onlined so that the
     newly added memory range can be uniquely referenced by numa apis"

NOTE! I'm not entirely happy with the whole "PMEM as RAM" model because
we currently have special - and very annoying rules in the kernel about
accessing PMEM only with the "MC safe" accessors, because machine checks
inside the regular repeat string copy functions can be fatal in some
(not described) circumstances.

And apparently the PMEM modules can cause that a lot more than regular
RAM.  The argument is that this happens because PMEM doesn't necessarily
get scrubbed at boot like RAM does, but that is planned to be added for
the user space tooling.

Quoting Dan from another email:
 "The exposure can be reduced in the volatile-RAM case by scanning for
  and clearing errors before it is onlined as RAM. The userspace tooling
  for that can be in place before v5.1-final. There's also runtime
  notifications of errors via acpi_nfit_uc_error_notify() from
  background scrubbers on the DIMM devices. With that mechanism the
  kernel could proactively clear newly discovered poison in the volatile
  case, but that would be additional development more suitable for v5.2.

  I understand the concern, and the need to highlight this issue by
  tapping the brakes on feature development, but I don't see PMEM as RAM
  making the situation worse when the exposure is also there via DAX in
  the PMEM case. Volatile-RAM is arguably a safer use case since it's
  possible to repair pages where the persistent case needs active
  application coordination"

* tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: "Hotplug" persistent memory for use like normal RAM
  mm/resource: Let walk_system_ram_range() search child resources
  mm/memory-hotplug: Allow memory resources to be children
  mm/resource: Move HMM pr_debug() deeper into resource code
  mm/resource: Return real error codes from walk failures
  device-dax: Add a 'modalias' attribute to DAX 'bus' devices
  device-dax: Add a 'target_node' attribute
  device-dax: Auto-bind device after successful new_id
  acpi/nfit, device-dax: Identify differentiated memory with a unique numa-node
  device-dax: Add /sys/class/dax backwards compatibility
  device-dax: Add support for a dax override driver
  device-dax: Move resource pinning+mapping into the common driver
  device-dax: Introduce bus + driver model
  device-dax: Start defining a dax bus model
  device-dax: Remove multi-resource infrastructure
  device-dax: Kill dax_region base
  device-dax: Kill dax_region ida

Pull more SCSI updates from James Bottomley:
 "This is the final round of mostly small fixes and performance
  improvements to our initial submit.

  The main regression fix is the ia64 simscsi build failure which was
  missed in the serial number elimination conversion"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
  scsi: ia64: simscsi: use request tag instead of serial_number
  scsi: aacraid: Fix performance issue on logical drives
  scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
  scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
  scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
  scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
  scsi: hisi_sas: Set PHY linkrate when disconnected
  scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
  scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
  scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
  scsi: qla2xxx: check for kstrtol() failure
  scsi: lpfc: fix 32-bit format string warning
  scsi: lpfc: fix unused variable warning
  scsi: target: tcmu: Switch to bitmap_zalloc()
  scsi: libiscsi: fall back to sendmsg for slab pages
  scsi: qla2xxx: avoid printf format warning
  scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
  scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
  scsi: ufs: hisi: fix ufs_hba_variant_ops passing
  scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
  ...

Pull more block layer changes from Jens Axboe:
 "This is a collection of both stragglers, and fixes that came in after
  I finalized the initial pull. This contains:

   - An MD pull request from Song, with a few minor fixes

   - Set of NVMe patches via Christoph

   - Pull request from Konrad, with a few fixes for xen/blkback

   - pblk fix IO calculation fix (Javier)

   - Segment calculation fix for pass-through (Ming)

   - Fallthrough annotation for blkcg (Mathieu)"

* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
  blkcg: annotate implicit fall through
  nvme-tcp: support C2HData with SUCCESS flag
  nvmet: ignore EOPNOTSUPP for discard
  nvme: add proper write zeroes setup for the multipath device
  nvme: add proper discard setup for the multipath device
  nvme: remove nvme_ns_config_oncs
  nvme: disable Write Zeroes for qemu controllers
  nvmet-fc: bring Disconnect into compliance with FC-NVME spec
  nvmet-fc: fix issues with targetport assoc_list list walking
  nvme-fc: reject reconnect if io queue count is reduced to zero
  nvme-fc: fix numa_node when dev is null
  nvme-fc: use nr_phys_segments to determine existence of sgl
  nvme-loop: init nvmet_ctrl fatal_err_work when allocate
  nvme: update comment to make the code easier to read
  nvme: put ns_head ref if namespace fails allocation
  nvme-trace: fix cdw10 buffer overrun
  nvme: don't warn on block content change effects
  nvme: add get-feature to admin cmds tracer
  md: Fix failed allocation of md_register_thread
  It's wrong to add len to sector_nr in raid10 reshape twice
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfixes:
   - Fix an Oops in SUNRPC back channel tracepoints
   - Fix a SUNRPC client regression when handling oversized replies
   - Fix the minimal size for SUNRPC reply buffer allocation
   - rpc_decode_header() must always return a non-zero value on error
   - Fix a typo in pnfs_update_layout()

  Cleanup:
   - Remove redundant check for the reply length in call_decode()"

* tag 'nfs-for-5.1-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Remove redundant check for the reply length in call_decode()
  SUNRPC: Handle the SYSTEM_ERR rpc error
  SUNRPC: rpc_decode_header() must always return a non-zero value on error
  SUNRPC: Use the ENOTCONN error on socket disconnect
  SUNRPC: Fix the minimal size for reply buffer allocation
  SUNRPC: Fix a client regression when handling oversized replies
  pNFS: Fix a typo in pnfs_update_layout
  fix null pointer deref in tracepoints in back channel

Pull powerpc fixes from Michael Ellerman:
 "One fix to prevent runtime allocation of 16GB pages when running in a
  VM (as opposed to bare metal), because it doesn't work.

  A small fix to our recently added KCOV support to exempt some more
  code from being instrumented.

  Plus a few minor build fixes, a small dead code removal and a
  defconfig update.

  Thanks to: Alexey Kardashevskiy, Aneesh Kumar K.V, Christophe Leroy,
  Jason Yan, Joel Stanley, Mahesh Salgaonkar, Mathieu Malaterre"

* tag 'powerpc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Include <asm/nmi.h> header file to fix a warning
  powerpc/powernv: Fix compile without CONFIG_TRACEPOINTS
  powerpc/mm: Disable kcov for SLB routines
  powerpc: remove dead code in head_fsl_booke.S
  powerpc/configs: Sync skiroot defconfig
  powerpc/hugetlb: Don't do runtime allocation of 16G pages in LPAR configuration

Pull vfs mount infrastructure fix from Al Viro:
 "Fixup for sysfs braino.

  Capabilities checks for sysfs mount do include those on netns, but
  only if CONFIG_NET_NS is enabled. Sorry, should've caught that
  earlier..."

* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix sysfs_init_fs_context() in !CONFIG_NET_NS case

Permission checks on current's netns should be done only when
netns are enabled.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fixes: 23bf1b6bSigned-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull more smb3 updates from Steve French:
 "Various tracing and debugging improvements, crediting fixes, some
  cleanup, and important fallocate fix (fixes three xfstests) and lock
  fix.

  Summary:

   - Various additional dynamic tracing tracepoints

   - Debugging improvements (including ability to query the server via
     SMB3 fsctl from userspace tools which can help with stats and
     debugging)

   - One minor performance improvement (root directory inode caching)

   - Crediting (SMB3 flow control) fixes

   - Some cleanup (docs and to mknod)

   - Important fixes: one to smb3 implementation of fallocate zero range
     (which fixes three xfstests) and a POSIX lock fix"

* tag '5.1-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6: (22 commits)
  CIFS: fix POSIX lock leak and invalid ptr deref
  SMB3: Allow SMB3 FSCTL queries to be sent to server from tools
  cifs: fix incorrect handling of smb2_set_sparse() return in smb3_simple_falloc
  smb2: fix typo in definition of a few error flags
  CIFS: make mknod() an smb_version_op
  cifs: minor documentation updates
  cifs: remove unused value pointed out by Coverity
  SMB3: passthru query info doesn't check for SMB3 FSCTL passthru
  smb3: add dynamic tracepoints for simple fallocate and zero range
  cifs: fix smb3_zero_range so it can expand the file-size when required
  cifs: add SMB2_ioctl_init/free helpers to be used with compounding
  smb3: Add dynamic trace points for various compounded smb3 ops
  cifs: cache FILE_ALL_INFO for the shared root handle
  smb3: display volume serial number for shares in /proc/fs/cifs/DebugData
  cifs: simplify how we handle credits in compound_send_recv()
  smb3: add dynamic tracepoint for timeout waiting for credits
  smb3: display security information in /proc/fs/cifs/DebugData more accurately
  cifs: add a timeout argument to wait_for_free_credits
  cifs: prevent starvation in wait_for_free_credits for multi-credit requests
  cifs: wait_for_free_credits() make it possible to wait for >=1 credits
  ...

Pull UML updates from Richard Weinberger:
 "Bugfix for the UML block device driver"

* 'for-linus-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Fix for a possible OOPS in ubd initialization
  um: Remove duplicated include from vector_user.c

Pull KVM updates from Paolo Bonzini:
 "ARM:
   - some cleanups
   - direct physical timer assignment
   - cache sanitization for 32-bit guests

  s390:
   - interrupt cleanup
   - introduction of the Guest Information Block
   - preparation for processor subfunctions in cpu models

  PPC:
   - bug fixes and improvements, especially related to machine checks
     and protection keys

  x86:
   - many, many cleanups, including removing a bunch of MMU code for
     unnecessary optimizations
   - AVIC fixes

  Generic:
   - memcg accounting"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
  kvm: vmx: fix formatting of a comment
  KVM: doc: Document the life cycle of a VM and its resources
  MAINTAINERS: Add KVM selftests to existing KVM entry
  Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
  KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
  KVM: PPC: Fix compilation when KVM is not enabled
  KVM: Minor cleanups for kvm_main.c
  KVM: s390: add debug logging for cpu model subfunctions
  KVM: s390: implement subfunction processor calls
  arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
  KVM: arm/arm64: Remove unused timer variable
  KVM: PPC: Book3S: Improve KVM reference counting
  KVM: PPC: Book3S HV: Fix build failure without IOMMU support
  Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
  x86: kvmguest: use TSC clocksource if invariant TSC is exposed
  KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
  KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
  KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
  KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
  KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
  ...

Pull tracing fixes and cleanups from Steven Rostedt:
 "This contains a series of last minute clean ups, small fixes and error
  checks"

* tag 'trace-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/probe: Verify alloc_trace_*probe() result
  tracing/probe: Check event/group naming rule at parsing
  tracing/probe: Check the size of argument name and body
  tracing/probe: Check event name length correctly
  tracing/probe: Check maxactive error cases
  tracing: kdb: Fix ftdump to not sleep
  trace/probes: Remove kernel doc style from non kernel doc comment
  tracing/probes: Make reserved_field_names static