- 25 May, 2021 7 commits
-
-
Daniel Borkmann authored
Given we don't need to simulate the speculative domain for registers with immediates anymore since the verifier uses direct imm-based rewrites instead of having to mask, we can also lift a few cases that were previously rejected. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org>
-
Daniel Borkmann authored
In 801c6058 ("bpf: Fix leakage of uninitialized bpf stack under speculation") we replaced masking logic with direct loads of immediates if the register is a known constant. Given in this case we do not apply any masking, there is also no reason for the operation to be truncated under the speculative domain. Therefore, there is also zero reason for the verifier to branch-off and simulate this case, it only needs to do it for unknown but bounded scalars. As a side-effect, this also enables few test cases that were previously rejected due to simulation under zero truncation. Signed-off-by:
Piotr Krysiuk <piotras@gmail.com> Acked-by:
-
Daniel Borkmann authored
Masking direction as indicated via mask_to_left is considered to be calculated once and then used to derive pointer limits. Thus, this needs to be placed into bpf_sanitize_info instead so we can pass it to sanitize_ptr_alu() call after the pointer move. Piotr noticed a corner case where the off reg causes masking direction change which then results in an incorrect final aux->alu_limit. Fixes: 7fedb63a ("bpf: Tighten speculative pointer arithmetic mask") Reported-by:
-
Daniel Borkmann authored
Add a container structure struct bpf_sanitize_info which holds the current aux info, and update call-sites to sanitize_ptr_alu() to pass it in. This is needed for passing in additional state later on. Signed-off-by:
-
Daniel Borkmann authored
Similarly as 6bdacdb4 ("bpf: Fix BPF_JIT kconfig symbol dependency") we need to detangle the hard BPF_LSM dependency on NET. This was previously implicit by its dependency on BPF_JIT which itself was dependent on NET (but without any actual/real hard dependency code-wise). Given the latter was lifted, so should be the former as BPF_LSMs could well exist on net-less systems. This therefore also fixes a randconfig build error recently reported by Randy: ld: kernel/bpf/bpf_lsm.o: in function `bpf_lsm_func_proto': bpf_lsm.c:(.text+0x1a0): undefined reference to `bpf_sk_storage_get_proto' ld: bpf_lsm.c:(.text+0x1b8): undefined reference to `bpf_sk_storage_delete_proto' [...] Fixes: b24abcff ("bpf, kconfig: Add consolidated menu entry for bpf with core options") Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Jussi Maki authored
Add a test case for using bpf_skb_change_head() in combination with bpf_redirect_peer() to redirect a packet from a L3 device to veth and back. The test uses a BPF program that adds L2 headers to the packet coming from a L3 device and then calls bpf_redirect_peer() to redirect the packet to a veth device. The test fails as skb->mac_len is not set properly and thus the ethernet headers are not properly skb_pull'd in cls_bpf_classify(), causing tcp_v4_rcv() to point the TCP header into middle of the IP header. Signed-off-by:
Jussi Maki <joamaki@gmail.com> Signed-off-by:
-
Liu Jian authored
The help information was not added at the time when the function got added. Fix this and add the missing information to its cli, documentation and bash completion. Fixes: db94cc0b ("bpftool: Add support for BPF_CGROUP_INET_SOCK_RELEASE") Signed-off-by:
Liu Jian <liujian56@huawei.com> Signed-off-by:
Quentin Monnet <quentin@isovalent.com> Link: https://lore.kernel.org/bpf/20210525014139.323859-1-liujian56@huawei.com
-
- 20 May, 2021 7 commits
-
-
Jussi Maki authored
The skb_change_head() helper did not set "skb->mac_len", which is problematic when it's used in combination with skb_redirect_peer(). Without it, redirecting a packet from a L3 device such as wireguard to the veth peer device will cause skb->data to point to the middle of the IP header on entry to tcp_v4_rcv() since the L2 header is not pulled correctly due to mac_len=0. Fixes: 3a0af8fd ("bpf: BPF for lightweight tunnel infrastructure") Signed-off-by:
-
Yinjun Zhang authored
Commit 4976b718 ("bpf: Introduce pseudo_btf_id") switched the order of resolve_pseudo_ldimm(), in which some pseudo instructions are rewritten. Thus those rewritten instructions cannot be passed to driver via 'prepare' offload callback. Reorder the 'prepare' offload callback to fix it. Fixes: 4976b718 ("bpf: Introduce pseudo_btf_id") Signed-off-by:
Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20210520085834.15023-1-simon.horman@netronome.com
-
Florent Revest authored
The cppcheck static code analysis reported the following error: if (WARN_ON_ONCE(nest_level > ARRAY_SIZE(bufs->tmp_bufs))) { ^ ARRAY_SIZE is a macro that expands to sizeofs, so bufs is not actually dereferenced at runtime, and the code is actually safe. But to keep things tidy, this patch removes the need for a call to ARRAY_SIZE by extracting the size of the array into a macro. Cppcheck should no longer be confused and the code ends up being a bit cleaner. Fixes: e2d5b2bb ("bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers") Reported-by:kernel test robot <lkp@intel.com> Signed-off-by:
Florent Revest <revest@chromium.org> Signed-off-by:
Song Liu <song@kernel.org> Link: https://lore.kernel.org/bpf/20210517092830.1026418-2-revest@chromium.org
-
Florent Revest authored
The per-cpu buffers contain bprintf data rather than printf arguments. The macro name and comment were a bit confusing, this rewords them in a clearer way. Signed-off-by:
-
Andrii Nakryiko authored
Extend ringbuf selftest to validate read/write and read-only restrictions on memory mapping consumer/producer/data pages. Ensure no "escalations" from PROT_READ to PROT_WRITE/PROT_EXEC is allowed. And test that mremap() fails to expand mmap()'ed area. Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by:
Andrii Nakryiko <andrii@kernel.org> Signed-off-by:
-
Stanislav Fomichev authored
Both IFINDEX_SRC and IFINDEX_DST are set from the userspace and it won't work once bpf merges with bpf-next. Fixes: 096eccde ("selftests/bpf: Rewrite test_tc_redirect.sh as prog_tests/tc_redirect.c") Signed-off-by:
Stanislav Fomichev <sdf@google.com> Signed-off-by:
-
Daniel Borkmann authored
Randy reported a randconfig build error recently on i386: ld: arch/x86/net/bpf_jit_comp32.o: in function `do_jit': bpf_jit_comp32.c:(.text+0x28c9): undefined reference to `__bpf_call_base' ld: arch/x86/net/bpf_jit_comp32.o: in function `bpf_int_jit_compile': bpf_jit_comp32.c:(.text+0x3694): undefined reference to `bpf_jit_blind_constants' ld: bpf_jit_comp32.c:(.text+0x3719): undefined reference to `bpf_jit_binary_free' ld: bpf_jit_comp32.c:(.text+0x3745): undefined reference to `bpf_jit_binary_alloc' ld: bpf_jit_comp32.c:(.text+0x37d3): undefined reference to `bpf_jit_prog_release_other' [...] The cause was that b24abcff ("bpf, kconfig: Add consolidated menu entry for bpf with core options") moved BPF_JIT from net/Kconfig into kernel/bpf/Kconfig and previously BPF_JIT was guarded by a 'if NET'. However, there is no actual dependency on NET, it's just that menuconfig NET selects BPF. And the latter in turn causes kernel/bpf/core.o to be built which contains above symbols. Randy's randconfig didn't have NET set, and BPF wasn't either, but BPF_JIT otoh was. Detangle this by making BPF_JIT depend on BPF instead. arm64 was the only arch that pulled in its JIT in net/ via obj-$(CONFIG_NET), all others unconditionally pull this dir in via obj-y. Do the same since CONFIG_NET guard there is really useless as we compiled the JIT via obj-$(CONFIG_BPF_JIT) += bpf_jit_comp.o anyway. Fixes: b24abcff ("bpf, kconfig: Add consolidated menu entry for bpf with core options") Reported-by:
-
- 11 May, 2021 26 commits
-
-
Alex Elder authored
IPA configuration data includes an array of memory region descriptors. That was a fixed-size array at one time, but at some point we started defining it such that it was only as big as required for a given platform. The actual number of entries in the array is recorded in the configuration data along with the array. A loop in ipa_mem_config() still assumes the array has entries for all defined memory region IDs. As a result, this loop can go past the end of the actual array and attempt to write "canary" values based on nonsensical data. Fix this, by stashing the number of entries in the array, and using that rather than IPA_MEM_COUNT in the initialization loop found in ipa_mem_config(). The only remaining use of IPA_MEM_COUNT is in a validation check to ensure configuration data doesn't have too many entries. That's fine for now. Fixes: 3128aae8 ("net: ipa: redefine struct ipa_mem_data") Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Shannon Nelson authored
When IONIC=y and PTP_1588_CLOCK=m were set in the .config file the driver link failed with undefined references. We add the dependancy depends on PTP_1588_CLOCK || !PTP_1588_CLOCK to clear this up. If PTP_1588_CLOCK=m, the depends limits IONIC to =m (or disabled). If PTP_1588_CLOCK is disabled, IONIC can be any of y/m/n. Fixes: 61db421d ("ionic: link in the new hw timestamp code") Reported-by:
Shannon Nelson <snelson@pensando.io> Acked-by:
-
Paolo Abeni authored
Maxim reported several issues when forcing a TCP transparent proxy to use the MPTCP protocol for the inbound connections. He also provided a clean reproducer. The problem boils down to 'mptcp_frag_can_collapse_to()' assuming that only MPTCP will use the given page_frag. If others - e.g. the plain TCP protocol - allocate page fragments, we can end-up re-using already allocated memory for mptcp_data_frag. Fix the issue ensuring that the to-be-expanded data fragment is located at the current page frag end. v1 -> v2: - added missing fixes tag (Mat) Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/178Reported-and-tested-by:
Maxim Galaganov <max@internet.ru> Fixes: 18b683bf ("mptcp: queue data for mptcp level retransmission") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Daniel Borkmann says: ==================== pull-request: bpf 2021-05-11 The following pull-request contains BPF updates for your *net* tree. We've added 13 non-merge commits during the last 8 day(s) which contain a total of 21 files changed, 817 insertions(+), 382 deletions(-). The main changes are: 1) Fix multiple ringbuf bugs in particular to prevent writable mmap of read-only pages, from Andrii Nakryiko & Thadeu Lima de Souza Cascardo. 2) Fix verifier alu32 known-const subregister bound tracking for bitwise operations and/or/xor, from Daniel Borkmann. 3) Reject trampoline attachment for functions with variable arguments, and also add a deny list of other forbidden functions, from Jiri Olsa. 4) Fix nested bpf_bprintf_prepare() calls used by various helpers by switching to per-CPU buffers, from Florent Revest. 5) Fix kernel compilation with BTF debug info on ppc64 due to pahole missing TCP-CC functions like cubictcp_init, from Martin KaFai Lau. 6) Add a kconfig entry to provide an option to disallow unprivileged BPF by default, from Daniel Borkmann. 7) Fix libbpf compilation for older libelf when GELF_ST_VISIBILITY() macro is not available, from Arnaldo Carvalho de Melo. 8) Migrate test_tc_redirect to test_progs framework as prep work for upcoming skb_change_head() fix & selftest, from Jussi Maki. 9) Fix a libbpf segfault in add_dummy_ksym_var() if BTF is not present, from Ian Rogers. 10) Fix tx_only micro-benchmark in xdpsock BPF sample with proper frame size, from Magnus Karlsson. ==================== Signed-off-by: -
David S. Miller authored
Merge tag 'mac80211-for-net-2021-05-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== pull-request: mac80211 2021-05-11 So exciting times, for the first pull request for fixes I have a bunch of security things that have been under embargo for a while - see more details in the tag below, and at the patch posting message I linked to. I organized with Kalle to just have a single set of fixes for mac80211 and ath10k/ath11k, we don't know about any of the other vendors (the mac80211 + already released firmware is sufficient to fix iwlwifi.) Please pull and let me know if there's any problem. Several security issues in the 802.11 implementations were found by Mathy Vanhoef (New York University Abu Dhabi), and this contains the fixes developed for mac80211 and specifically Qualcomm drivers, I'm sending this together (as agreed with Kalle) to have just a single set of patches for now. We don't know about other vendors though. More details in the patch posting: https://lore.kernel.org/r/20210511180259.159598-1-johannes@sipsolutions.net ==================== Signed-off-by:
-
Joakim Zhang authored
Both get and set WoL will check device_can_wakeup(), if MAC supports PMT, it will set device wakeup capability. After commit 1d8e5b0f ("net: stmmac: Support WOL with phy"), device wakeup capability will be overwrite in stmmac_init_phy() according to phy's Wol feature. If phy doesn't support WoL, then MAC will lose wakeup capability. To fix this issue, only overwrite device wakeup capability when MAC doesn't support PMT. For STMMAC now driver checks MAC's WoL capability if MAC supports PMT, if not support, driver will check PHY's WoL capability. Fixes: 1d8e5b0f ("net: stmmac: Support WOL with phy") Reviewed-by:
Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by:
-
Martin KaFai Lau authored
During the discussion in [0]. It was pointed out that static functions in ppc64 is prefixed with ".". For example, the 'readelf -s vmlinux.ppc': 89326: c000000001383280 24 NOTYPE LOCAL DEFAULT 31 cubictcp_init 89327: c000000000c97c50 168 FUNC LOCAL DEFAULT 2 .cubictcp_init The one with FUNC type is ".cubictcp_init" instead of "cubictcp_init". The "." seems to be done by arch/powerpc/include/asm/ppc_asm.h. This caused that pahole cannot generate the BTF for these tcp-cc kernel functions because pahole only captures the FUNC type and "cubictcp_init" is not. It then failed the kernel compilation in ppc64. This behavior is only reported in ppc64 so far. I tried arm64, s390, and sparc64 and did not observe this "." prefix and NOTYPE behavior. Since the kfunc call is only supported in the x86_64 and x86_32 JIT, this patch limits those tcp-cc functions to x86 only to avoid unnecessary compilation issue in other ARCHs. In the future, we can examine if it is better to change all those functions from static to extern. [0] https://lore.kernel.org/bpf/4e051459-8532-7b61-c815-f3435767f8a0@kernel.org/ Fixes: e78aea8b ("bpf: tcp: Put some tcp cong functions in allowlist for bpf-tcp-cc") Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
-
Jussi Maki authored
As discussed in [0], this ports test_tc_redirect.sh to the test_progs framework and removes the old test. This makes it more in line with rest of the tests and makes it possible to run this test case with vmtest.sh and under the bpf CI. The upcoming skb_change_head() helper fix in [0] is depending on it and extending the test case to redirect a packet from L3 device to veth. [0] https://lore.kernel.org/bpf/20210427135550.807355-1-joamaki@gmail.comSigned-off-by:
-
Arnaldo Carvalho de Melo authored
Where that macro isn't available. Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Florent Revest authored
The bpf_seq_printf, bpf_trace_printk and bpf_snprintf helpers share one per-cpu buffer that they use to store temporary data (arguments to bprintf). They "get" that buffer with try_get_fmt_tmp_buf and "put" it by the end of their scope with bpf_bprintf_cleanup. If one of these helpers gets called within the scope of one of these helpers, for example: a first bpf program gets called, uses bpf_trace_printk which calls raw_spin_lock_irqsave which is traced by another bpf program that calls bpf_snprintf, then the second "get" fails. Essentially, these helpers are not re-entrant. They would return -EBUSY and print a warning message once. This patch triples the number of bprintf buffers to allow three levels of nesting. This is very similar to what was done for tracepoints in "9594dc3c bpf: fix nested bpf tracepoints with per-cpu data" Fixes: d9c9e4db ("bpf: Factorize bpf_trace_printk and bpf_seq_printf") Reported-by: syzbot+63122d0bc347f18c1884@syzkaller.appspotmail.com Signed-off-by:
-
Jiri Olsa authored
The recursion check in __bpf_prog_enter and __bpf_prog_exit leaves some (not inlined) functions unprotected: In __bpf_prog_enter: - migrate_disable is called before prog->active is checked In __bpf_prog_exit: - migrate_enable,rcu_read_unlock_strict are called after prog->active is decreased When attaching trampoline to them we get panic like: traps: PANIC: double fault, error_code: 0x0 double fault: 0000 [#1] SMP PTI RIP: 0010:__bpf_prog_enter+0x4/0x50 ... Call Trace: <IRQ> bpf_trampoline_6442466513_0+0x18/0x1000 migrate_disable+0x5/0x50 __bpf_prog_enter+0x9/0x50 bpf_trampoline_6442466513_0+0x18/0x1000 migrate_disable+0x5/0x50 __bpf_prog_enter+0x9/0x50 bpf_trampoline_6442466513_0+0x18/0x1000 migrate_disable+0x5/0x50 __bpf_prog_enter+0x9/0x50 bpf_trampoline_6442466513_0+0x18/0x1000 migrate_disable+0x5/0x50 ... Fixing this by adding deny list of btf ids for tracing programs and checking btf id during program verification. Adding above functions to this list. Suggested-by:Jiri Olsa <jolsa@kernel.org> Signed-off-by:
-
Daniel Borkmann authored
Add a kconfig knob which allows for unprivileged bpf to be disabled by default. If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2. This still allows a transition of 2 -> {0,1} through an admin. Similarly, this also still keeps 1 -> {1} behavior intact, so that once set to permanently disabled, it cannot be undone aside from a reboot. We've also added extra2 with max of 2 for the procfs handler, so that an admin still has a chance to toggle between 0 <-> 2. Either way, as an additional alternative, applications can make use of CAP_BPF that we added a while ago. Signed-off-by: -
Daniel Borkmann authored
Right now, all core BPF related options are scattered in different Kconfig locations mainly due to historic reasons. Moving forward, lets add a proper subsystem entry under ... General setup ---> BPF subsystem ---> ... in order to have all knobs in a single location and thus ease BPF related configuration. Networking related bits such as sockmap are out of scope for the general setup and therefore better suited to remain in net/Kconfig. Signed-off-by: -
Sriram R authored
Fragmentation is used only with unicast frames. Drop multicast fragments to avoid any undesired behavior. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2 Cc: stable@vger.kernel.org Signed-off-by:
Sriram R <srirrama@codeaurora.org> Signed-off-by:
Jouni Malinen <jouni@codeaurora.org> Link: https://lore.kernel.org/r/20210511200110.1d53bfd20a8b.Ibb63283051bb5e2c45951932c6e1f351d5a73dc3@changeidSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Sriram R authored
Currently the fragment cache setup during peer assoc is cleared only during peer delete. In case a key reinstallation happens with the same peer, the same fragment cache with old fragments added before key installation could be clubbed with fragments received after. This might be exploited to mix fragments of different data resulting in a proper unintended reassembled packet to be passed up the stack. Hence flush the fragment cache on every key installation to prevent potential attacks (CVE-2020-24587). Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2 Cc: stable@vger.kernel.org Signed-off-by:
-
Sriram R authored
In certain scenarios a normal MSDU can be received as an A-MSDU when the A-MSDU present bit of a QoS header gets flipped during reception. Since this bit is unauthenticated, the hardware crypto engine can pass the frame to the driver without any error indication. This could result in processing unintended subframes collected in the A-MSDU list. Hence, validate A-MSDU list by checking if the first frame has a valid subframe header. Comparing the non-aggregated MSDU and an A-MSDU, the fields of the first subframe DA matches the LLC/SNAP header fields of a normal MSDU. In order to avoid processing such frames, add a validation to filter such A-MSDU frames where the first subframe header DA matches with the LLC/SNAP header pattern. Tested-on: QCA9984 hw1.0 PCI 10.4-3.10-00047 Cc: stable@vger.kernel.org Signed-off-by:
-
Wen Gong authored
TKIP Michael MIC was not verified properly for PCIe cases since the validation steps in ieee80211_rx_h_michael_mic_verify() in mac80211 did not get fully executed due to unexpected flag values in ieee80211_rx_status. Fix this by setting the flags property to meet mac80211 expectations for performing Michael MIC validation there. This fixes CVE-2020-26141. It does the same as ath10k_htt_rx_proc_rx_ind_hl() for SDIO which passed MIC verification case. This applies only to QCA6174/QCA9377 PCIe. Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1 Cc: stable@vger.kernel.org Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
-
Wen Gong authored
When the discard flag is set by the firmware for an MPDU, it should be dropped. This allows a mitigation for CVE-2020-24588 to be implemented in the firmware. Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049 Cc: stable@vger.kernel.org Signed-off-by:
-
Wen Gong authored
Fragmentation is not used with multicast frames. Discard unexpected fragments with multicast DA. This fixes CVE-2020-26145. Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049 Cc: stable@vger.kernel.org Signed-off-by:
-
Wen Gong authored
Fragmentation is not used with multicast frames. Discard unexpected fragments with multicast DA. This fixes CVE-2020-26145. Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1 Cc: stable@vger.kernel.org Signed-off-by:
-
Wen Gong authored
PN replay check for not fragmented frames is finished in the firmware, but this was not done for fragmented frames when ath10k is used with QCA6174/QCA6377 PCIe. mac80211 has the function ieee80211_rx_h_defragment() for PN replay check for fragmented frames, but this does not get checked with QCA6174 due to the ieee80211_has_protected() condition not matching the cleared Protected bit case. Validate the PN of received fragmented frames within ath10k when CCMP is used and drop the fragment if the PN is not correct (incremented by exactly one from the previous fragment). This applies only for QCA6174/QCA6377 PCIe. Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1 Cc: stable@vger.kernel.org Signed-off-by:
-
Wen Gong authored
For some chips/drivers, e.g., QCA6174 with ath10k, the decryption is done by the hardware, and the Protected bit in the Frame Control field is cleared in the lower level driver before the frame is passed to mac80211. In such cases, the condition for ieee80211_has_protected() is not met in ieee80211_rx_h_defragment() of mac80211 and the new security validation steps are not executed. Extend mac80211 to cover the case where the Protected bit has been cleared, but the frame is indicated as having been decrypted by the hardware. This extends protection against mixed key and fragment cache attack for additional drivers/chips. This fixes CVE-2020-24586 and CVE-2020-24587 for such cases. Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1 Cc: stable@vger.kernel.org Signed-off-by:
-
Johannes Berg authored
EAPOL frames are used for authentication and key management between the AP and each individual STA associated in the BSS. Those frames are not supposed to be sent by one associated STA to another associated STA (either unicast for broadcast/multicast). Similarly, in 802.11 they're supposed to be sent to the authenticator (AP) address. Since it is possible for unexpected EAPOL frames to result in misbehavior in supplicant implementations, it is better for the AP to not allow such cases to be forwarded to other clients either directly, or indirectly if the AP interface is part of a bridge. Accept EAPOL (control port) frames only if they're transmitted to the own address, or, due to interoperability concerns, to the PAE group address. Disable forwarding of EAPOL (or well, the configured control port protocol) frames back to wireless medium in all cases. Previously, these frames were accepted from fully authenticated and authorized stations and also from unauthenticated stations for one of the cases. Additionally, to avoid forwarding by the bridge, rewrite the PAE group address case to the local MAC address. Cc: stable@vger.kernel.org Co-developed-by:
-
Johannes Berg authored
Similar to the issues fixed in previous patches, TKIP and WEP should be protected even if for TKIP we have the Michael MIC protecting it, and WEP is broken anyway. However, this also somewhat protects potential other algorithms that drivers might implement. Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210511200110.430e8c202313.Ia37e4e5b6b3eaab1a5ae050e015f6c92859dbe27@changeidSigned-off-by:
-
Johannes Berg authored
As pointed out by Mathy Vanhoef, we implement the RX PN check on fragmented frames incorrectly - we check against the last received PN prior to the new frame, rather than to the one in this frame itself. Prior patches addressed the security issue here, but in order to be able to reason better about the code, fix it to really compare against the current frame's PN, not the last stored one. Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210511200110.bfbc340ff071.Id0b690e581da7d03d76df90bb0e3fd55930bc8a0@changeidSigned-off-by:
-
Johannes Berg authored
Prior patches protected against fragmentation cache attacks by coloring keys, but this shows that it can lead to issues when multiple stations use the same sequence number. Add a fragment cache to struct sta_info (in addition to the one in the interface) to separate fragments for different stations properly. This then automatically clear most of the fragment cache when a station disconnects (or reassociates) from an AP, or when client interfaces disconnect from the network, etc. On the way, also fix the comment there since this brings us in line with the recommendation in 802.11-2016 ("An AP should support ..."). Additionally, remove a useless condition (since there's no problem purging an already empty list). Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210511200110.fc35046b0d52.I1ef101e3784d13e8f6600d83de7ec9a3a45bcd52@changeidSigned-off-by:
-
