- 20 Nov, 2012 3 commits
-
-
Andrei Emeltchenko authored
Instead of printing: "[ 7763.082007] Bluetooth: 2" print something like: "[ 7763.082007] Bluetooth: Trailing bytes: 2 in sframe" Signed-off-by:
Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk>
-
Andrei Emeltchenko authored
local_amp_id is used in l2cap_physical_cfm and shall be set up before calling it. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Andrei Emeltchenko authored
When receiving Physical Link Completed event we need to create L2CAP channel with L2CAP Create Chan Request. Current code was sending this command only if connection was pending (which is probably needed in channel move case). If channel is not moved but created Create Chan should be sent for outgoing channel which is checked with BT_CONNECT flag. Signed-off-by:
-
- 19 Nov, 2012 10 commits
-
-
Szymon Janc authored
Read Local OOB Data command can take more than 1 second on some chips. e.g. on CSR 0a12:0001 first call to Read Local OOB Data after reset takes about 1300ms resulting in tx timeout error. [27698.368655] Bluetooth: hci0 command 0x0c57 tx timeout 2012-10-31 15:53:36.178585 < HCI Command: Read Local OOB Data (0x03|0x0057) plen 0 2012-10-31 15:53:37.496996 > HCI Event: Command Complete (0x0e) plen 36 Read Local OOB Data (0x03|0x0057) ncmd 1 status 0x00 hash 0x92219d9b447f2aa9dc12dda2ae7bae6a randomizer 0xb1948d0febe4ea38ce85c4e66313beba Signed-off-by:Szymon Janc <szymon.janc@tieto.com> Signed-off-by:
-
Jeff Cook authored
Vendor-specific ID for BCM20702A0. Support for bluetooth over Asus Wi-Fi GO!, included with Asus P8Z77-V Deluxe. T: Bus=07 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0b05 ProdID=17b5 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=94DBC98AC113 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Cc: stable@vger.kernel.org Signed-off-by:
Jeff Cook <jeff@deserettechnology.com> Signed-off-by:
-
Andrei Emeltchenko authored
Signed-off-by:
-
Andrei Emeltchenko authored
Set chan->fcs to L2CAP_FCS_NONE only for new L2CAP channels (not moved). Other side can still request to use FCS. Signed-off-by:
-
Andrei Emeltchenko authored
Remove locking from l2cap_physical_cfm and lock chan inside amp_physical_cfm. Signed-off-by:
-
Andrei Emeltchenko authored
local_amp_id is already set in l2cap_connect() which is called several lines above. Signed-off-by:
-
Andrei Emeltchenko authored
Use helper instead of test_bit. This is the only place left using test CONF_CONNECT_PEND flag. Signed-off-by:
-
Johan Hedberg authored
This patch adds a callback for the HCI_LE_Set_Advertise_Enable command. The callback is responsible for updating the HCI_LE_PERIPHERAL flag updating as well as updating the advertising data flags field to indicate undirected connectable advertising. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Acked-by:
-
Johan Hedberg authored
This patch adds support for setting basing LE advertising data. The three elements supported for now are the advertising flags, the TX power and the friendly name. Signed-off-by:
-
Johan Hedberg authored
The core specification defines 127 as the "not available" value (well, "reserved" for BR/EDR and "not available" for LE - but essentially the same). Therefore, instead of testing for 0 (which is in fact a valid value) we should be using this invalid value to test if the tx_power is available. Signed-off-by:
-
- 16 Nov, 2012 27 commits
-
-
Sujith Manoharan authored
2484 Mhz (Japan) usage requires filter coefficients to be programmed in the CCK TX FIR registers. This is required for AR9331, AR9485 and AR9462. Fix this and also remove a few useless macros and a duplicate variable. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
There's no need to ask the user about lib80211 since it will be selected by drivers requiring it, hide it from Kconfig. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
The driver doesn't use any lib80211 symbols so it shouldn't select it in Kconfig. Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Wei Yongjun authored
Using eth_zero_addr() to assign zero address insetad of memset() or an inefficient copy from a static array. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Stanislav Yakovlev authored
Remove unnecessary if statements because libipw_set_geo always returns success. Also change function's return value from int to void. Signed-off-by:
Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by:
-
Hante Meuleman authored
Removing obsolete functions and prototypes. Moving (and renaming) defines to place with similar definitions. Removing unnecessary includes. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
Franky Lin <frankyl@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
When debug is turned on for fwil then the whole data buffer is dumped. In some cases this gives excessive amount of debug. With this patch the dumps are limited to 64 bytes. Reviewed-by:
-
Hante Meuleman authored
On sdio module unload followed by load (without removing the device) the access window should be moved back to enumeration space. Force this by removing initialisation of sbwad during probe. Reviewed-by:
-
Hante Meuleman authored
brcmf_ops_sdio_probe used the private_date func->card->dev to store device data of brcmfmac sdio. This is not a good place to store the data. Use dev of func and use func->card->sdio_func to group the functions the driver is using. Reviewed-by:
-
Hante Meuleman authored
on sdio remove the bus_if should be configured for close, so new data from higher layers will be blocked. Also the access to bus_if in the watchdog should be checked for null pointer access on sdio remove. Reviewed-by:
-
Hante Meuleman authored
when brcmf_sdbrcm_probe_attach results in error then cleanup will result in null pointer access. In brcmf_sdbrcm_release and in brcmf_ops_sdio_remove. This patch fixes order of init and de-init. Reviewed-by:
-
Hante Meuleman authored
In brcmf_sdbrcm_probe only error ELINK is seen as error. However brcmf_bus_start can return many more error codes and all should result in failed init of driver. Reviewed-by:
-
Arend van Spriel authored
The IF event need special care. It can be either an ADD, DEL, or CHANGE. For an ADD we need to call brcmf_add_if() before the event handler call. Upon a DEL we need to call brcmf_del_if() after the event handler call. CHANGE does not require special attention. Reviewed-by:
-
Arend van Spriel authored
Firmware fires IF event to add the primary interface but that is already created in the driver. Reviewed-by:
-
Arend van Spriel authored
Replaced <linux/unaligned/access_ok.h> by <asm/unaligned.h> to make it work on ARM and other architectures. Reviewed-by:
-
Hante Meuleman authored
brcmf_fweh_detach can be called while ifp is already NULL, due to init error. Fix NULL pointer access by checking ifp. Reviewed-by:
-
Arend van Spriel authored
The mac_addr field in ifp object is always valid so no need to validate. Reviewed-by:
-
Arend van Spriel authored
The function brcmf_add_if() is called with mac address set to NULL for the primary interface. When handling IF ADD events the firmware provides a address mask in the event to derive its mac address from the primary mac address. Rename the parameter and use it as a mask. Reviewed-by:
-
Arend van Spriel authored
Testing revealed the IF ADD event contains the interface index of the new interface. This would result in a NULL pointer access when handling the event. Reviewed-by:
-
Arend van Spriel authored
virtual netdevice interface like P2P client and GO need different callbacks for .open and .down. This patch adds those. Reviewed-by:
-
Arend van Spriel authored
The brcmf_add_if() function had a struct device as parameter to accomodate the bus specific code to use this function. The driver has been reworked so the bus specific code does not need this function. Better replace the parameter with a more specific driver object, ie. struct brcmf_pub. Reviewed-by:
-
Hante Meuleman authored
Add support for usb suspend/resume. Reviewed-by:
-
Hante Meuleman authored
Clean code related to firmware download routines. Remove obsolete delay and increase delay after reset command. Reviewed-by:
-
Arend van Spriel authored
Handling of firmware event has been reworked into a seperate code file. The change is needed as firmware event can be received in interrupt context. Decoupling of the event handling has been lowered to allow event processing to sleep. Reviewed-by:
-
Dan Carpenter authored
'|' has higher precedence than ?:. Since AR5K_PHY_TURBO_MODE is 0x1 and "AR5K_PHY_TURBO_MODE | (ah->ah_radio == AR5K_RF2425)" is true then we always set turbo to zero. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Syam Sidhardhan authored
Simplify the code by make use of module_platform_driver macro. Signed-off-by:
Syam Sidhardhan <s.syam@samsung.com> Signed-off-by:
-
Sujith Manoharan authored
The workaround for ASPM/L0s is needed only for AR9485 1.0, which was never sold and is not supported by ath9k. Signed-off-by:
-
