- 12 Aug, 2015 3 commits
-
-
Alexey Khoroshilov authored
commit 53e20f2e upstream. There was an omission in transition to devm_xxx resource handling. iounmap(udc->phy_regs) were removed, but ioremap() was left without devm_. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Fixes: 3517c31a ("usb: gadget: mv_udc: use devm_xxx for probe") Signed-off-by:
Felipe Balbi <balbi@ti.com> [ luis: backported to 3.16: - file rename: drivers/usb/gadget/udc/mv_udc_core.c -> drivers/usb/gadget/mv_udc_core.c ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Tilman Schmidt authored
commit fd98e941 upstream. Commit 79901317 ("n_tty: Don't flush buffer when closing ldisc"), first merged in kernel release 3.10, caused the following regression in the Gigaset M101 driver: Before that commit, when closing the N_TTY line discipline in preparation to switching to N_GIGASET_M101, receive_room would be reset to a non-zero value by the call to n_tty_flush_buffer() in n_tty's close method. With the removal of that call, receive_room might be left at zero, blocking data reception on the serial line. The present patch fixes that regression by setting receive_room to an appropriate value in the ldisc open method. Fixes: 79901317 ("n_tty: Don't flush buffer when closing ldisc") Signed-off-by:
Tilman Schmidt <tilman@imap.cc> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Nikolay Aleksandrov authored
commit 5ebc7846 upstream. Since the mdb add/del code was introduced there have been 2 br_mdb_notify calls when doing br_mdb_add() resulting in 2 notifications on each add. Example: Command: bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent Before patch: root@debian:~# bridge monitor all [MDB]dev br0 port eth1 grp 239.0.0.1 permanent [MDB]dev br0 port eth1 grp 239.0.0.1 permanent After patch: root@debian:~# bridge monitor all [MDB]dev br0 port eth1 grp 239.0.0.1 permanent Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: cfd56754 ("bridge: add support of adding and deleting mdb entries") Signed-off-by:
-
- 11 Aug, 2015 37 commits
-
-
Dan Carpenter authored
commit 50c2e4dd upstream. The > should be >=. I also added spaces around the '-' operations so the code is a little more consistent and matches the condition better. Fixes: f53c3fe8 ('xen-netback: Introduce TX grant mapping') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Scott Wood authored
commit 5f867db6 upstream. Commit 66507c7b ("mtd: nand: Add support to use nand_base poi databuf as bounce buffer") added a flag NAND_USE_BOUNCE_BUFFER using the same bit value as the existing NAND_BUSWIDTH_AUTO. Cc: Kamal Dasu <kdasu.kdev@gmail.com> Fixes: 66507c7b ("mtd: nand: Add support to use nand_base poi databuf as bounce buffer") Signed-off-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Kishon Vijay Abraham I authored
commit 408806f7 upstream. DTO/DCRC errors were not being informed to the mmc core since commit ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC errors. This is because after this commit 'host->data' is checked after it has been cleared to NULL by omap_hsmmc_dma_cleanup(). Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked making core layer not to be aware of DTO/DCRC errors. Because of this any command invoked after DTO/DCRC error leads to a hang. Fix this by checking for 'host->data' before it is actually cleared. Fixes: ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ") Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Vignesh R <vigneshr@ti.com> Tested-by:
Andreas Fenkart <afenkart@gmail.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
NeilBrown authored
commit 34cab6f4 upstream. When we get a read error from the last working device, we don't try to repair it, and don't fail the device. We simple report a read error to the caller. However the current test for 'is this the last working device' is wrong. When there is only one fully working device, it assumes that a non-faulty device is that device. However a spare which is rebuilding would be non-faulty but so not the only working device. So change the test from "!Faulty" to "In_sync". If ->degraded says there is only one fully working device and this device is in_sync, this must be the one. This bug has existed since we allowed read_balance to read from a recovering spare in v3.0 Reported-and-tested-by:
Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Martin K. Petersen authored
commit f3f5da62 upstream. This fixes a data corruption bug when using discard on top of MD linear, raid0 and raid10 personalities. Commit 20d0189b "block: Introduce new bio_split()" permits sharing the bio_vec between the two resulting bios. That is fine for read/write requests where the bio_vec is immutable. For discards, however, we need to be able to attach a payload and update the bio_vec so the page can get mapped to a scatterlist entry. Therefore the bio_vec can not be shared when splitting discards and we must do a full clone. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Reported-by:
Seunguk Shin <seunguk.shin@samsung.com> Tested-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Bernhard Bender authored
commit 96849170 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by:
Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by:
Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Chris Metcalf authored
commit 3f81d244 upstream. We were previously using free_bootmem() and just getting lucky that nothing too bad happened. Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
Tejun Heo authored
commit 5f6c2d2b upstream. When a blkcg configuration is targeted to a partition rather than a whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it forgets to put the gendisk ref in that case. Fix it. Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Oliver Neukum authored
commit 5fb2c782 upstream. This device automatically switches itself to another mode (0x1405) unless the specific access pattern of Windows is followed in its initial mode. That makes a dirty unmount of the internal storage devices inevitable if they are mounted. So the card reader of such a device should be ignored, lest an unclean removal become inevitable. This replaces an earlier patch that ignored all LUNs of this device. That patch was overly broad. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Reviewed-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Alan Stern authored
commit 7d8021c9 upstream. This patch fixes a bug introduced by commit 977dcfdc ("USB: OHCI: don't lose track of EDs when a controller dies"). The commit changed ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had been called. The user-visible consequence is that the driver occasionally crashes or locks up when an URB is submitted while another URB for the same endpoint is being unlinked. This patch moves the ED state change later, to the right place. The drawback is that now we may unnecessarily execute some instructions multiple times when a controller dies. Since controllers dying is an exceptional occurrence, a little wasted time won't matter. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Heiko Przybyl <lil_tux@web.de> Tested-by:
-
Lu Baolu authored
commit 2d2a3167 upstream. Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed root hub. The intention of that change was to avoid touching usb core internal field, a.k.a. lpm_capable, and let usb core to set it by checking U1 and U2 exit latency values in the descriptor. Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately, root hub is a special usb device as it has no parent. Hub_port_init() will never be called for a root hub device. That means lpm_capable will by no means be set for the root hub. As the result, lpm isn't functional at all in Linux kernel. This patch add the code to check and set lpm_capable when registering a root hub device. It could be back-ported to kernels as old as v3.15, that contains the Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM."). Reported-by:
Kevin Strasser <kevin.strasser@linux.intel.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
-
Zhuang Jin Can authored
commit aca3a048 upstream. Port link change with port in resume state should not be reported to usbcore, as this is an internal state to be handled by xhci driver. Reporting PLC to usbcore may cause usbcore clearing PLC first and port change event irq won't be generated. Signed-off-by:
Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Zhuang Jin Can authored
commit fac4271d upstream. When the link is just waken, it's in Resume state, and driver sets PLS to U0. This refers to Phase 1. Phase 2 refers to when the link has completed the transition from Resume state to U0. With the fix of xhci: report U3 when link is in resume state, it also exposes an issue that usb3 roothub and controller can suspend right after phase 1, and this causes a hard hang in controller. To fix the issue, we need to prevent usb3 bus suspend if any port is resuming in phase 1. [merge separate USB2 and USB3 port resume checking to one -Mathias] Signed-off-by:
-
Zhuang Jin Can authored
commit 243292a2 upstream. xhci_hub_report_usb3_link_state() returns pls as U0 when the link is in resume state, and this causes usb core to think the link is in U0 while actually it's in resume state. When usb core transfers control request on the link, it fails with TRB error as the link is not ready for transfer. To fix the issue, report U3 when the link is in resume state, thus usb core knows the link it's not ready for transfer. Signed-off-by:
-
Brian Campbell authored
commit 326124a0 upstream. When resetting a device the number of active TTs may need to be corrected by xhci_update_tt_active_eps, but the number of old active endpoints supplied to it was always zero, so the number of TTs and the bandwidth reserved for them was not updated, and could rise unnecessarily. This affected systems using Intel's Patherpoint chipset, which rely on software bandwidth checking. For example, a Lenovo X230 would lose the ability to use ports on the docking station after enough suspend/resume cycles because the bandwidth calculated would rise with every cycle when a suitable device is attached. The correct number of active endpoints is calculated in the same way as in xhci_reserve_bandwidth. Signed-off-by:
Brian Campbell <bacam@z273.org.uk> Signed-off-by:
-
AMAN DEEP authored
commit 34968106 upstream. virt_dev->num_cached_rings counts on freed ring and is not updated correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring is added into cache and then num_rings_cache is incremented as below: virt_dev->ring_cache[rings_cached] = virt_dev->eps[ep_index].ring; virt_dev->num_rings_cached++; here, free ring pointer is added to a current index and then index is incremented. So current index always points to empty location in the ring cache. For getting available free ring, current index should be decremented first and then corresponding ring buffer value should be taken from ring cache. But In function xhci_endpoint_init(), the num_rings_cached index is accessed before decrement. virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; virt_dev->num_rings_cached--; This is bug in manipulating the index of ring cache. And it should be as below: virt_dev->num_rings_cached--; virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; Signed-off-by:
Aman Deep <aman.deep@samsung.com> Signed-off-by:
-
John Youn authored
commit aebda618 upstream. This fixes an issue introduced in commit b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by:
Huang Rui <ray.huang@amd.com> Tested-by:
Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com> Fixes: b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
-
Subbaraya Sundeep Bhatta authored
commit 76e838c9 upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by:
Subbaraya Sundeep Bhatta <sbhatta@xilinx.com> Fixes: 72246da4 (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by:
-
Chris Wilson authored
commit 648a9bc5 upstream. Since the hardware sometimes mysteriously totally flummoxes the 64bit read of a 64bit register when read using a single instruction, split the read into two instructions. Since the read here is of automatically incrementing timestamp counters, we also have to be very careful in order to make sure that it does not increment between the two instructions. However, since userspace tried to workaround this issue and so enshrined this ABI for a broken hardware read and in the process neglected that the read only fails in some environments, we have to introduce a new uABI flag for userspace to request the 2x32 bit accurate read of the timestamp. v2: Fix alignment check and include details of the workaround for userspace. Reported-by:
Karol Herbst <freedesktop@karolherbst.de> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91317 Testcase: igt/gem_reg_read Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Michał Winiarski <michal.winiarski@intel.com> Tested-by:
Michał Winiarski <michal.winiarski@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Aaron Plattner authored
commit 6c3d9119 upstream. Vendor ID 0x10de007d is used by a yet-to-be-named GPU chip. This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is appropriate here. Signed-off-by:
Aaron Plattner <aplattner@nvidia.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Simon Guinot authored
commit a84e3289 upstream. With the actual code, if a memory allocation error happens while refilling a Rx descriptor, then the original Rx buffer is both passed to the networking stack (in a SKB) and let in the Rx ring. This leads to various kernel oops and crashes. As a fix, this patch moves Rx descriptor refilling ahead of building SKB with the associated Rx buffer. In case of a memory allocation failure, data is dropped and the original DMA buffer is put back into the Rx ring. Signed-off-by:
Simon Guinot <simon.guinot@sequanux.org> Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Tested-by:
Yoann Sculo <yoann@sculo.fr> Signed-off-by:
-
Fugang Duan authored
commit bf604a4c upstream. Read the register only when the adc register address is 4 byte aligned. (rather than the other way around). Signed-off-by:
Haibo Chen <haibo.chen@freescale.com> Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Tom Hughes authored
commit 4479004e upstream. If we don't do this, and we then fail to recreate the debugfs directory during a mode change, then we will fail later trying to add stations to this now bogus directory: BUG: unable to handle kernel NULL pointer dereference at 0000006c IP: [<c0a92202>] mutex_lock+0x12/0x30 Call Trace: [<c0678ab4>] start_creating+0x44/0xc0 [<c0679203>] debugfs_create_dir+0x13/0xf0 [<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211] Signed-off-by:
Tom Hughes <tom@compton.nu> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Martin K. Petersen authored
commit 9051bd39 upstream. A new Micron drive was just announced, once again recycling the first part of the model string. Add an underscore to the M510/M550 pattern to avoid picking up the new DC drive. Signed-off-by:
-
Stefan Agner authored
commit 25b401c1 upstream. If a valid power regulator or a dummy regulator is used (which happens to be the case when no regulator is specified), restart_work is queued no matter whether the device was running or not at suspend time. Since work queues get initialized in the ndo_open callback, resuming leads to a NULL pointer exception. Reverse exactly the steps executed at suspend time: - Enable the power regulator in any case - Enable the transceiver regulator if the device was running, even in case we have a power regulator - Queue restart_work only in case the device was running Fixes: bf66f373 ("can: mcp251x: Move to threaded interrupts instead of workqueues.") Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Mikulas Patocka authored
commit d531be2c upstream. I have a ST4000DM000 disk. If Linux is booted while the disk is spun down, the command that sets transfer mode causes the disk to spin up. The spin-up takes longer than the default 5s timeout, so the command fails and timeout is reported. Fix this by increasing the timeout to 15s, which is enough for the disk to spin up. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Arne Fitzenreiter authored
commit cda57b1b upstream. This device loses blocks, often the partition table area, on trim. Disable TRIM. http://pcengines.ch/msata16a.htmSigned-off-by:
Arne Fitzenreiter <arne_f@ipfire.org> Signed-off-by:
-
Arne Fitzenreiter authored
commit 71d126fd upstream. Some devices lose data on TRIM whether queued or not. This patch adds a horkage to disable TRIM. tj: Collapsed unnecessary if() nesting. Signed-off-by:
-
Aleksei Mamlin authored
commit 08c85d2a upstream. Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors: [ 3.788362] ata3.00: failed to enable AA (error_mask=0x1) [ 3.789243] ata3.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. tj: Collected FPDMA_AA entries and updated comment. Signed-off-by:
Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by:
-
Lior Amsalem authored
commit 945b4744 upstream. This commit adds the necessary quirk to make the Marvell 4140 SATA PMP work properly. This PMP doesn't like SRST on port number 4 (the host port) so this commit marks this port as not supporting SRST. Signed-off-by:
Lior Amsalem <alior@marvell.com> Reviewed-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
Antonio Borneo authored
commit 6debce6f upstream. Current implementation of cp2112_raw_event() only accepts one data report at a time. If last received data report is not fully handled yet, a new incoming data report will overwrite it. In such case we don't guaranteed to propagate the correct incoming data. The trivial fix implemented here forces a single report at a time by requesting in cp2112_read() no more than 61 byte of data, which is the payload size of a single data report. Signed-off-by:
Antonio Borneo <borneo.antonio@gmail.com> Tested-by:
Ellen Wang <ellen@cumulusnetworks.com> Signed-off-by:
Jiri Kosina <jkosina@suse.com> Signed-off-by:
-
Al Viro authored
commit 451a2886 upstream. unfortunately, allowing an arbitrary 16bit value means a possibility of overflow in the calculation of total number of pages in bio_map_user_iov() - we rely on there being no more than PAGE_SIZE members of sum in the first loop there. If that sum wraps around, we end up allocating too small array of pointers to pages and it's easy to overflow it in the second loop. X-Coverup: TINC (and there's no lumber cartel either) Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [bwh: s/MAX_UIOVEC/UIO_MAXIOV/. This was fixed upstream by commit fdc81f45 ("sg_start_req(): use import_iovec()"), but we don't have that function.] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Alan Stern authored
commit 3f2cee73 upstream. The usbfs API has a peculiar hole: Users are not allowed to reap their URBs after the device has been disconnected. There doesn't seem to be any good reason for this; it is an ad-hoc inconsistency. The patch allows users to issue the USBDEVFS_REAPURB and USBDEVFS_REAPURBNDELAY ioctls (together with their 32-bit counterparts on 64-bit systems) even after the device is gone. If no URBs are pending for a disconnected device then the ioctls will return -ENODEV rather than -EAGAIN, because obviously no new URBs will ever be able to complete. The patch also adds a new capability flag for USBDEVFS_GET_CAPABILITIES to indicate that the reap-after-disconnect feature is supported. Signed-off-by:
Chris Dickens <christopher.a.dickens@gmail.com> Acked-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Greg Kroah-Hartman <greg@kroah.com> Signed-off-by:
-
Mimi Zohar authored
commit 5101a185 upstream. To prevent offline stripping of existing file xattrs and relabeling of them at runtime, EVM allows only newly created files to be labeled. As pseudo filesystems are not persistent, stripping of xattrs is not a concern. Some LSMs defer file labeling on pseudo filesystems. This patch permits the labeling of existing files on pseudo files systems. Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> [ luis: backported to 3.16: - added magic.h header file ] Signed-off-by:
-
Kirill A. Shutemov authored
commit 6b7339f4 upstream. Reading page fault handler code I've noticed that under right circumstances kernel would map anonymous pages into file mappings: if the VMA doesn't have vm_ops->fault() and the VMA wasn't fully populated on ->mmap(), kernel would handle page fault to not populated pte with do_anonymous_page(). Let's change page fault handler to use do_anonymous_page() only on anonymous VMA (->vm_ops == NULL) and make sure that the VMA is not shared. For file mappings without vm_ops->fault() or shred VMA without vm_ops, page fault on pte_none() entry would lead to SIGBUS. Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [ luis: backported to 3.16: used Kirill's backport to 3.18 ] Signed-off-by:
-
Colin Ian King authored
commit ca4da5dd upstream. __key_link_end is not freeing the associated array edit structure and this leads to a 512 byte memory leak each time an identical existing key is added with add_key(). The reason the add_key() system call returns okay is that key_create_or_update() calls __key_link_begin() before checking to see whether it can update a key directly rather than adding/replacing - which it turns out it can. Thus __key_link() is not called through __key_instantiate_and_link() and __key_link_end() must cancel the edit. CVE-2015-1333 Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Cc: Moritz Mühlenhoff <jmm@inutil.org> Signed-off-by:
-
Wengang Wang authored
commit 4fabb594 upstream. Fixes: 3e0249f9 ("RDS/IB: add refcount tracking to struct rds_ib_device") There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr failed(mr pool running out). this lead to the refcount overflow. A complain in line 117(see following) is seen. From vmcore: s_ib_rdma_mr_pool_depleted is 2147485544 and rds_ibdev->refcount is -2147475448. That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely to return ERR_PTR(-EAGAIN). 115 void rds_ib_dev_put(struct rds_ib_device *rds_ibdev) 116 { 117 BUG_ON(atomic_read(&rds_ibdev->refcount) <= 0); 118 if (atomic_dec_and_test(&rds_ibdev->refcount)) 119 queue_work(rds_wq, &rds_ibdev->free_work); 120 } fix is to drop refcount when rds_ib_alloc_fmr failed. Signed-off-by:
Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by:
Haggai Eran <haggaie@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
