For a port to be able to use EEE, both the MAC and the PHY must
support EEE. A phy can be provided by both a phydev or phylink. Verify
at least one of these exist, not just phydev.

Fixes: aab9c406 ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: fixes 2018-08-08

here are small fixes for SMC: The first patch makes sure, shutdown code
is not executed for sockets in state SMC_LISTEN. The second patch resets
send and receive buffer values for accepted sockets, since TCP buffer size
optimizations for the internal CLC socket should not be forwarded to the
outer SMC socket. The third patch solves a race between connect and ioctl
reported by syzbot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When an SMC socket is connecting it is decided whether fallback to
TCP is needed. To avoid races between connect and ioctl move the
sock lock before the use_fallback check.

Reported-by: syzbot+5b2cece1a8ecb2ca77d8@syzkaller.appspotmail.com
Reported-by: syzbot+19557374321ca3710990@syzkaller.appspotmail.com
Fixes: 1992d998 ("net/smc: take sock lock in smc_ioctl()")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without setsockopt SO_SNDBUF and SO_RCVBUF settings, the sysctl
defaults net.ipv4.tcp_wmem and net.ipv4.tcp_rmem should be the base
for the sizes of the SMC sndbuf and rcvbuf. Any TCP buffer size
optimizations for servers should be ignored.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Invoking shutdown for a socket in state SMC_LISTEN does not make
sense. Nevertheless programs like syzbot fuzzing the kernel may
try to do this. For SMC this means a socket refcounting problem.
This patch makes sure a shutdown call for an SMC socket in state
SMC_LISTEN simply returns with -ENOTCONN.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.

Fixes: b21f502f ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

AF_RXRPC has a keepalive message generator that generates a message for a
peer ~20s after the last transmission to that peer to keep firewall ports
open.  The implementation is incorrect in the following ways:

 (1) It mixes up ktime_t and time64_t types.

 (2) It uses ktime_get_real(), the output of which may jump forward or
     backward due to adjustments to the time of day.

 (3) If the current time jumps forward too much or jumps backwards, the
     generator function will crank the base of the time ring round one slot
     at a time (ie. a 1s period) until it catches up, spewing out VERSION
     packets as it goes.

Fix the problem by:

 (1) Only using time64_t.  There's no need for sub-second resolution.

 (2) Use ktime_get_seconds() rather than ktime_get_real() so that time
     isn't perceived to go backwards.

 (3) Simplifying rxrpc_peer_keepalive_worker() by splitting it into two
     parts:

     (a) The "worker" function that manages the buckets and the timer.

     (b) The "dispatch" function that takes the pending peers and
     	 potentially transmits a keepalive packet before putting them back
     	 in the ring into the slot appropriate to the revised last-Tx time.

 (4) Taking everything that's pending out of the ring and splicing it into
     a temporary collector list for processing.

     In the case that there's been a significant jump forward, the ring
     gets entirely emptied and then the time base can be warped forward
     before the peers are processed.

     The warping can't happen if the ring isn't empty because the slot a
     peer is in is keepalive-time dependent, relative to the base time.

 (5) Limit the number of iterations of the bucket array when scanning it.

 (6) Set the timer to skip any empty slots as there's no point waking up if
     there's nothing to do yet.

This can be triggered by an incoming call from a server after a reboot with
AF_RXRPC and AFS built into the kernel causing a peer record to be set up
before userspace is started.  The system clock is then adjusted by
userspace, thereby potentially causing the keepalive generator to have a
meltdown - which leads to a message like:

	watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/0:1:23]
	...
	Workqueue: krxrpcd rxrpc_peer_keepalive_worker
	EIP: lock_acquire+0x69/0x80
	...
	Call Trace:
	 ? rxrpc_peer_keepalive_worker+0x5e/0x350
	 ? _raw_spin_lock_bh+0x29/0x60
	 ? rxrpc_peer_keepalive_worker+0x5e/0x350
	 ? rxrpc_peer_keepalive_worker+0x5e/0x350
	 ? __lock_acquire+0x3d3/0x870
	 ? process_one_work+0x110/0x340
	 ? process_one_work+0x166/0x340
	 ? process_one_work+0x110/0x340
	 ? worker_thread+0x39/0x3c0
	 ? kthread+0xdb/0x110
	 ? cancel_delayed_work+0x90/0x90
	 ? kthread_stop+0x70/0x70
	 ? ret_from_fork+0x19/0x24

Fixes: ace45bec ("rxrpc: Fix firewall route keepalive")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5e fixes 2018-08-07

I know it is late into 4.18 release, and this is why I am submitting
only two mlx5e ethernet fixes.

The first one from Or, is needed for -stable and it fixes hairpin
for "same device" check.

The second fix is a non risk fix from Huy which cleans up and improves
error return value reporting for dcbnl_ieee_setapp.

For -stable v4.16
- net/mlx5e: Properly check if hairpin is possible between two functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused netdev_registered_init/remove in en.h
Return ENOSUPPORT if the check MLX5_DSCP_SUPPORTED fails.
Remove extra white space

Fixes: 2a5e7a13 ("net/mlx5e: Add dcbnl dscp to priority support")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current check relies on function BDF addresses and can get
us wrong e.g when two VFs are assigned into a VM and the PCI
v-address is set by the hypervisor.

Fixes: 5c65c564 ('net/mlx5e: Support offloading TC NIC hairpin flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Alaa Hleihel <alaa@mellanox.com>
Tested-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to reset metadata cache during new IOTLB initialization,
otherwise the stale pointers to previous IOTLB may be still accessed
which will lead a use after free.

Reported-by: syzbot+c51e6736a1bf614b3272@syzkaller.appspotmail.com
Fixes: f8894913 ("vhost: introduce O(1) vq metadata cache")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc_sap_put() decreases the refcnt before deleting sap
from the global list. Therefore, there is a chance
llc_sap_find() could find a sap with zero refcnt
in this global list.

Close this race condition by checking if refcnt is zero
or not in llc_sap_find(), if it is zero then it is being
removed so we can just treat it as gone.

Reported-by: <syzbot+278893f3f7803871f7ce@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The shift of 'cwnd' with '(now - hc->tx_lsndtime) / hc->tx_rto' value
can lead to undefined behavior [1].

In order to fix this use a gradual shift of the window with a 'while'
loop, similar to what tcp_cwnd_restart() is doing.

When comparing delta and RTO there is a minor difference between TCP
and DCCP, the last one also invokes dccp_cwnd_restart() and reduces
'cwnd' if delta equals RTO. That case is preserved in this change.

[1]:
[40850.963623] UBSAN: Undefined behaviour in net/dccp/ccids/ccid2.c:237:7
[40851.043858] shift exponent 67 is too large for 32-bit type 'unsigned int'
[40851.127163] CPU: 3 PID: 15940 Comm: netstress Tainted: G        W   E     4.18.0-rc7.x86_64 #1
...
[40851.377176] Call Trace:
[40851.408503]  dump_stack+0xf1/0x17b
[40851.451331]  ? show_regs_print_info+0x5/0x5
[40851.503555]  ubsan_epilogue+0x9/0x7c
[40851.548363]  __ubsan_handle_shift_out_of_bounds+0x25b/0x2b4
[40851.617109]  ? __ubsan_handle_load_invalid_value+0x18f/0x18f
[40851.686796]  ? xfrm4_output_finish+0x80/0x80
[40851.739827]  ? lock_downgrade+0x6d0/0x6d0
[40851.789744]  ? xfrm4_prepare_output+0x160/0x160
[40851.845912]  ? ip_queue_xmit+0x810/0x1db0
[40851.895845]  ? ccid2_hc_tx_packet_sent+0xd36/0x10a0 [dccp]
[40851.963530]  ccid2_hc_tx_packet_sent+0xd36/0x10a0 [dccp]
[40852.029063]  dccp_xmit_packet+0x1d3/0x720 [dccp]
[40852.086254]  dccp_write_xmit+0x116/0x1d0 [dccp]
[40852.142412]  dccp_sendmsg+0x428/0xb20 [dccp]
[40852.195454]  ? inet_dccp_listen+0x200/0x200 [dccp]
[40852.254833]  ? sched_clock+0x5/0x10
[40852.298508]  ? sched_clock+0x5/0x10
[40852.342194]  ? inet_create+0xdf0/0xdf0
[40852.388988]  sock_sendmsg+0xd9/0x160
...

Fixes: 113ced1f ("dccp ccid-2: Perform congestion-window validation")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 9faa89d4 ("tipc: make function tipc_net_finalize() thread
safe") tries to make it thread safe to set node address, so it uses
node_list_lock lock to serialize the whole process of setting node
address in tipc_net_finalize(). But it causes the following interrupt
unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  rht_deferred_worker()
  rhashtable_rehash_table()
  lock(&(&ht->lock)->rlock)
			       tipc_nl_compat_doit()
                               tipc_net_finalize()
                               local_irq_disable();
                               lock(&(&tn->node_list_lock)->rlock);
                               tipc_sk_reinit()
                               rhashtable_walk_enter()
                               lock(&(&ht->lock)->rlock);
  <Interrupt>
  tipc_disc_rcv()
  tipc_node_check_dest()
  tipc_node_create()
  lock(&(&tn->node_list_lock)->rlock);

 *** DEADLOCK ***

When rhashtable_rehash_table() holds ht->lock on CPU0, it doesn't
disable BH. So if an interrupt happens after the lock, it can create
an inverse lock ordering between ht->lock and tn->node_list_lock. As
a consequence, deadlock might happen.

The reason causing the inverse lock ordering scenario above is because
the initial purpose of node_list_lock is not designed to do the
serialization of node address setting.

As cmpxchg() can guarantee CAS (compare-and-swap) process is atomic,
we use it to replace node_list_lock to ensure setting node address can
be atomically finished. It turns out the potential deadlock can be
avoided as well.

Fixes: 9faa89d4 ("tipc: make function tipc_net_finalize() thread safe")
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported that we reinitialize an active delayed
work in vsock_stream_connect():

	ODEBUG: init active (active state 0) object type: timer_list hint:
	delayed_work_timer_fn+0x0/0x90 kernel/workqueue.c:1414
	WARNING: CPU: 1 PID: 11518 at lib/debugobjects.c:329
	debug_print_object+0x16a/0x210 lib/debugobjects.c:326

The pattern is apparently wrong, we should only initialize
the dealyed work once and could repeatly schedule it. So we
have to move out the initializations to allocation side.
And to avoid confusion, we can split the shared dwork
into two, instead of re-using the same one.

Fixes: d021c344 ("VSOCK: Introduce VM Sockets")
Reported-by: <syzbot+8a9b1bd330476a4f3db6@syzkaller.appspotmail.com>
Cc: Andy king <acking@vmware.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The allocation of lmac->dmacs is not being checked for allocation
failure. Add the check.

Fixes: 3a34ecfd ("net: thunderx: add MAC address filter tracking for LMAC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike fs.val.lport and fs.val.fport, cxgb4_process_flow_match()
sets fs.val.{l,f}ip to net-endian values without conversion - they come
straight from flow_dissector_key_ipv4_addrs ->dst and ->src resp.  So
the assignment in mk_act_open_req() ought to be a straight copy.

	As far as I know, T4 PCIe cards do exist, so it's not as if that
thing could only be found on little-endian systems...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.

Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.

In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.

Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.

Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.

Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Fixes: eb73190f ("net/packet: refine check for priv area size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to RFC791, 68 bytes is the minimum size of IPv4 datagram every
device must be able to forward without further fragmentation while 576
bytes is the minimum size of IPv4 datagram every device has to be able
to receive, so in ip6_tnl_xmit(), 68(IPV4_MIN_MTU) should be the right
value for the ipv4 min mtu check in ip6_tnl_xmit.

While at it, change to use max() instead of if statement.

Fixes: c9fefa08 ("ip6_tunnel: get the min mtu properly in ip6_tnl_xmit")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All the callers of ip6_rt_copy_init()/rt6_set_from() hold refcnt
of the "from" fib6_info, so there is no need to hold fib6_metrics
refcnt again, because fib6_metrics refcnt is only released when
fib6_info is gone, that is, they have the same life time, so the
whole fib6_metrics refcnt can be removed actually.

This fixes a kmemleak warning reported by Sabrina.

Fixes: 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fix from Thomas Gleixner:
 "A single fix, which addresses boot failures on machines which do not
  report EBDA correctly, which can place the trampoline into reserved
  memory regions. Validating against E820 prevents that"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/compressed/64: Validate trampoline placement against E820

Pull timer fixes from Thomas Gleixner:
 "Two oneliners addressing NOHZ failures:

   - Use a bitmask to check for the pending timer softirq and not the
     bit number. The existing code using the bit number checked for
     the wrong bit, which caused timers to either expire late or stop
     completely.

   - Make the nohz evaluation on interrupt exit more robust. The
     existing code did not re-arm the hardware when interrupting a
     running softirq in task context (ksoftirqd or tail of
     local_bh_enable()), which caused timers to either expire late
     or stop completely"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  nohz: Fix missing tick reprogram when interrupting an inline softirq
  nohz: Fix local_timer_softirq_pending()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes for perf:

  Kernel side:

   - Fix the hardcoded index of extra PCI devices on Broadwell which
     caused a resource conflict and triggered warnings on CPU hotplug.

  Tooling:

   - Update the tools copy of several files, including perf_event.h,
     powerpc's asm/unistd.h (new io_pgetevents syscall), bpf.h and x86's
     memcpy_64.s (used in 'perf bench mem'), silencing the respective
     warnings during the perf tools build.

   - Fix the build on the alpine:edge distro"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/uncore: Fix hardcoded index of Broadwell extra PCI devices
  perf tools: Fix the build on the alpine:edge distro
  tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
  tools headers uapi: Refresh linux/bpf.h copy
  tools headers powerpc: Update asm/unistd.h copy to pick new
  tools headers uapi: Update tools's copy of linux/perf_event.h

Pull irq fix from Thomas Gleixner:
 "A single bugfix for the irq core to prevent silent data corruption and
  malfunction of threaded interrupts under certain conditions"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Make force irq threading setup more robust

Pull networking fixes from David Miller:

 1) Handle frames in error situations properly in AF_XDP, from Jakub
    Kicinski.

 2) tcp_mmap test case only tests ipv6 due to a thinko, fix from
    Maninder Singh.

 3) Session refcnt fix in l2tp_ppp, from Guillaume Nault.

 4) Fix regression in netlink bind handling of multicast gruops, from
    Dmitry Safonov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netlink: Don't shift on 64 for ngroups
  net/smc: no cursor update send in state SMC_INIT
  l2tp: fix missing refcount drop in pppol2tp_tunnel_ioctl()
  mlxsw: core_acl_flex_actions: Remove redundant mirror resource destruction
  mlxsw: core_acl_flex_actions: Remove redundant counter destruction
  mlxsw: core_acl_flex_actions: Remove redundant resource destruction
  mlxsw: core_acl_flex_actions: Return error for conflicting actions
  selftests/bpf: update test_lwt_seg6local.sh according to iproute2
  drivers: net: lmc: fix case value for target abort error
  selftest/net: fix protocol family to work for IPv4.
  net: xsk: don't return frames via the allocator on error
  tools/bpftool: fix a percpu_array map dump problem

Pull usercopy whitelisting fix from Kees Cook:
 "Bart Massey discovered that the usercopy whitelist for JFS was
  incomplete: the inline inode data may intentionally "overflow" into
  the neighboring "extended area", so the size of the whitelist needed
  to be raised to include the neighboring field"

* tag 'usercopy-fix-v4.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  jfs: Fix usercopy whitelist for inline inode data

Pull xfs bugfix from Darrick Wong:
 "One more patch for 4.18 to fix a coding error in the iomap_bmap()
  function introduced in -rc1: fix incorrect shifting"

* tag 'xfs-4.18-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  fs: fix iomap_bmap position calculation

It turns out that commit 721c7fc7 ("block: fail op_is_write()
requests to read-only partitions"), while obviously correct, causes
problems for some older lvm2 installations.

The reason is that the lvm snapshotting will continue to write to the
snapshow COW volume, even after the volume has been marked read-only.
End result: snapshot failure.

This has actually been fixed in newer version of the lvm2 tool, but the
old tools still exist, and the breakage was reported both in the kernel
bugzilla and in the Debian bugzilla:

  https://bugzilla.kernel.org/show_bug.cgi?id=200439
  https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=900442

The lvm2 fix is here

  https://sourceware.org/git/?p=lvm2.git;a=commit;h=a6fdb9d9d70f51c49ad11a87ab4243344e6701a3

but until everybody has updated to recent versions, we'll have to weaken
the "never write to read-only partitions" check.  It now allows the
write to happen, but causes a warning, something like this:

  generic_make_request: Trying to write to read-only block-device dm-3 (partno X)
  Modules linked in: nf_tables xt_cgroup xt_owner kvm_intel iwlmvm kvm irqbypass iwlwifi
  CPU: 1 PID: 77 Comm: kworker/1:1 Not tainted 4.17.9-gentoo #3
  Hardware name: LENOVO 20B6A019RT/20B6A019RT, BIOS GJET91WW (2.41 ) 09/21/2016
  Workqueue: ksnaphd do_metadata
  RIP: 0010:generic_make_request_checks+0x4ac/0x600
  ...
  Call Trace:
   generic_make_request+0x64/0x400
   submit_bio+0x6c/0x140
   dispatch_io+0x287/0x430
   sync_io+0xc3/0x120
   dm_io+0x1f8/0x220
   do_metadata+0x1d/0x30
   process_one_work+0x1b9/0x3e0
   worker_thread+0x2b/0x3c0
   kthread+0x113/0x130
   ret_from_fork+0x35/0x40

Note that this is a "revert" in behavior only.  I'm leaving alone the
actual code cleanups in commit 721c7fc7, but letting the previously
uncaught request go through with a warning instead of stopping it.

Fixes: 721c7fc7 ("block: fail op_is_write() requests to read-only partitions")
Reported-and-tested-by: WGH <wgh@torlan.ru>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It's legal to have 64 groups for netlink_sock.

As user-supplied nladdr->nl_groups is __u32, it's possible to subscribe
only to first 32 groups.

The check for correctness of .bind() userspace supplied parameter
is done by applying mask made from ngroups shift. Which broke Android
as they have 64 groups and the shift for mask resulted in an overflow.

Fixes: 61f4b237 ("netlink: Don't shift with UB on nlk->ngroups")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-08-05

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix bpftool percpu_array dump by using correct roundup to next
   multiple of 8 for the value size, from Yonghong.

2) Fix in AF_XDP's __xsk_rcv_zc() to not returning frames back to
   allocator since driver will recycle frame anyway in case of an
   error, from Jakub.

3) Fix up BPF test_lwt_seg6local test cases to final iproute2
   syntax, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If a writer blocked condition is received without data, the current
consumer cursor is immediately sent. Servers could already receive this
condition in state SMC_INIT without finished tx-setup. This patch
avoids sending a consumer cursor update in this case.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bart Massey reported what turned out to be a usercopy whitelist false
positive in JFS when symlink contents exceeded 128 bytes. The inline
inode data (i_inline) is actually designed to overflow into the "extended
area" following it (i_inline_ea) when needed. So the whitelist needed to
be expanded to include both i_inline and i_inline_ea (the whole size
of which is calculated internally using IDATASIZE, 256, instead of
sizeof(i_inline), 128).

$ cd /mnt/jfs
$ touch $(perl -e 'print "B" x 250')
$ ln -s B* b
$ ls -l >/dev/null

[  249.436410] Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLUB object 'jfs_ip' (offset 616, size 250)!
Reported-by: Bart Massey <bart.massey@gmail.com>
Fixes: 8d2704d3 ("jfs: Define usercopy region in jfs_ip slab cache")
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: jfs-discussion@lists.sourceforge.net
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>

Pull KVM fixes from Paolo Bonzini:
 "Two vmx bugfixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: x86: vmx: fix vpid leak
  KVM: vmx: use local variable for current_vmptr when emulating VMPTRST

If 'session' is not NULL and is not a PPP pseudo-wire, then we fail to
drop the reference taken by l2tp_session_get().

Fixes: ecd012e4 ("l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Fix ACL actions error condition handling

Nir says:

Two issues were lately noticed within mlxsw ACL actions error condition
handling. The first patch deals with conflicting actions such as:

 # tc filter add dev swp49 parent ffff: \
   protocol ip pref 10 flower skip_sw dst_ip 192.168.101.1 \
   action goto chain 100 \
   action mirred egress redirect dev swp4

The second action will never execute, however SW model allows this
configuration, while the mlxsw driver cannot allow for it as it
implements actions in sets of up to three actions per set with a single
termination marking. Conflicting actions create a contradiction over
this single marking and thus cannot be configured. The fix replaces a
misplaced warning with an error code to be returned.

Patches 2-4 fix a condition of duplicate destruction of resources. Some
actions require allocation of specific resource prior to setting the
action itself. On error condition this resource was destroyed twice,
leading to a crash when using mirror action, and to a redundant
destruction in other cases, since for error condition rule destruction
also takes care of resource destruction. In order to fix this state a
symmetry in behavior is added and resource destruction also takes care
of removing the resource from rule's resource list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous patch mlxsw_afa_resource_del() was added to avoid a duplicate
resource detruction scenario.
For mirror actions, such duplicate destruction leads to a crash as in:

 # tc qdisc add dev swp49 ingress
 # tc filter add dev swp49 parent ffff: \
   protocol ip chain 100 pref 10 \
   flower skip_sw dst_ip 192.168.101.1 action drop
 # tc filter add dev swp49 parent ffff: \
   protocol ip pref 10 \
   flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
   action mirred egress mirror dev swp4

Therefore add a call to mlxsw_afa_resource_del() in
mlxsw_afa_mirror_destroy() in order to clear that resource
from rule's resources.

Fixes: d0d13c18 ("mlxsw: spectrum_acl: Add support for mirror action")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each tc flower rule uses a hidden count action. As counter resource may
not be available due to limited HW resources, update _counter_create()
and _counter_destroy() pair to follow previously introduced symmetric
error condition handling, add a call to mlxsw_afa_resource_del() as part
of the counter resource destruction.

Fixes: c18c1e18 ("mlxsw: core: Make counter index allocated inside the action append")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some ACL actions require the allocation of a separate resource
prior to applying the action itself. When facing an error condition
during the setup phase of the action, resource should be destroyed.
For such actions the destruction was done twice which is dangerous
and lead to a potential crash.
The destruction took place first upon error on action setup phase
and then as the rule was destroyed.

The following sequence generated a crash:

 # tc qdisc add dev swp49 ingress
 # tc filter add dev swp49 parent ffff: \
   protocol ip chain 100 pref 10 \
   flower skip_sw dst_ip 192.168.101.1 action drop
 # tc filter add dev swp49 parent ffff: \
   protocol ip pref 10 \
   flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
   action mirred egress mirror dev swp4

Therefore add mlxsw_afa_resource_del() as a complement of
mlxsw_afa_resource_add() to add symmetry to resource_list membership
handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the
_fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a
NOP.

Fixes: 140ce421 ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum switch ACL action set is built in groups of three actions
which may point to additional actions. A group holds a single record
which can be set as goto record for pointing at a following group
or can be set to mark the termination of the lookup. This is perfectly
adequate for handling a series of actions to be executed on a packet.
While the SW model allows configuration of conflicting actions
where it is clear that some actions will never execute, the mlxsw
driver must block such configurations as it creates a conflict
over the single terminate/goto record value.

For a conflicting actions configuration such as:

 # tc filter add dev swp49 parent ffff: \
   protocol ip pref 10 \
   flower skip_sw dst_ip 192.168.101.1 \
   action goto chain 100 \
   action mirred egress mirror dev swp4

Where it is clear that the last action will never execute, the
mlxsw driver was issuing a warning instead of returning an error.
Therefore replace that warning with an error for this specific
case.

Fixes: 4cda7d8d ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>