- 02 Jul, 2018 20 commits
-
-
Huazhong Tan authored
csq is used as a ring buffer, the value of the desc will be replaced in next use. This patch removes the unnecessary memset, and just updates the next_to_clean. Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Huazhong Tan authored
Remove some redundant assignments. desc->flag = cpu_to_le16(HCLGE_CMD_FLAG_NO_INTR | HCLGE_CMD_FLAG_IN) has set bit HCLGE_CMD_FLAG_WR to zero, so does others. Signed-off-by:
-
Huazhong Tan authored
There are some useless type cast, print in hclge_cmd_send. This patch removes them. Signed-off-by:
-
Huazhong Tan authored
hclge_ring_to_dma_dir is unused anywhere. This patch removes it. Signed-off-by:
-
Colin Ian King authored
Pointer zatm_dev is being assigned but is never used hence it is redundant and can be removed. Cleans up clang warning: warning: variable 'zatm_dev' set but not used [-Wunused-but-set-variable] Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Heiner Kallweit authored
RTL8211C has an issue when operating in Gigabit slave mode, therefore genphy driver can't be used. See also this U-boot change. https://lists.denx.de/pipermail/u-boot/2016-March/249712.html Add a PHY driver for this chip with the quirk to force Gigabit master mode. As a note: This will make it impossible to connect two network ports directly which both are driven by a RTl8211C. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Roman Mashak authored
Signed-off-by:
Roman Mashak <mrv@mojatatu.com> Signed-off-by:
-
Guenter Roeck authored
gcc 8.1.0 complains: drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_suspend.isra.1': drivers/isdn/i4l/isdn_tty.c:790:3: warning: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length drivers/isdn/i4l/isdn_tty.c:778:6: note: length computed here drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_resume': drivers/isdn/i4l/isdn_tty.c:880:3: warning: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length drivers/isdn/i4l/isdn_tty.c:817:6: note: length computed here Using strncpy() is indeed less than perfect since the length of data to be copied has already been determined with strlen(). Replace strncpy() with memcpy() to address the warning and optimize the code a little. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Heiner Kallweit authored
When adding support for RTL8211 I forgot to update the mdio_device_id table. Signed-off-by:
-
Yafang Shao authored
Currently trace_sock_exceed_buf_limit() only show rmem info, but wmem limit may also be hit. So expose wmem info in this tracepoint as well. Regarding memcg, I think it is better to introduce a new tracepoint(if that is needed), i.e. trace_memcg_limit_hit other than show memcg info in trace_sock_exceed_buf_limit. Signed-off-by:
Yafang Shao <laoar.shao@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
This hack (affecting the non-PCIe models only) was introduced in 2004 to deal with link negotiation failures in 1GBit mode. Based on a comment in the r8169 vendor driver I assume the issue affects RTL8169sb in combination with particular 1GBit switch models. Resetting the PHY every 10s and hoping that one fine day we will make it to establish the link seems to be very hacky to me. I'd say: If 1GBit doesn't work reliably in a users environment then the user should remove 1GBit from the advertised modes, e.g. by using ethtool -s <if> advertise <10/100 modes> If the issue affects one chip version only and that with most link partners, then we could also think of removing 1GBit from the advertised modes for this chip version in the driver. Signed-off-by:
-
Colin Ian King authored
Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then an out-of-bounds read on ipsec->sa will occur. Fix the incorrect bounds check by using >= rather than >. Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read") Fixes: 7699353d ("netdevsim: add ipsec offload testing") Signed-off-by:Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by:
-
David S. Miller authored
Amritha Nambiar says: ==================== Symmetric queue selection using XPS for Rx queues This patch series implements support for Tx queue selection based on Rx queue(s) map. This is done by configuring Rx queue(s) map per Tx-queue using sysfs attribute. If the user configuration for Rx queues does not apply, then the Tx queue selection falls back to XPS using CPUs and finally to hashing. XPS is refactored to support Tx queue selection based on either the CPUs map or the Rx-queues map. The config option CONFIG_XPS needs to be enabled. By default no receive queues are configured for the Tx queue. - /sys/class/net/<dev>/queues/tx-*/xps_rxqs A set of receive queues can be mapped to a set of transmit queues (many:many), although the common use case is a 1:1 mapping. This will enable sending packets on the same Tx-Rx queue association as this is useful for busy polling multi-threaded workloads where it is not possible to pin the threads to a CPU. This is a rework of Sridhar's patch for symmetric queueing via socket option: https://www.spinics.net/lists/netdev/msg453106.html Testing Hints: Kernel: Linux 4.17.0-rc7+ Interface: driver: ixgbe version: 5.1.0-k firmware-version: 0x00015e0b Configuration: ethtool -L $iface combined 16 ethtool -C $iface rx-usecs 1000 sysctl net.core.busy_poll=1000 ATR disabled: ethtool -K $iface ntuple on Workload: Modified memcached that changes the thread selection policy to be based on the incoming rx-queue of a connection using SO_INCOMING_NAPI_ID socket option. The default is round-robin. Default: No rxqs_map configured Symmetric queues: Enable rxqs_map for all queues 1:1 mapped to Tx queue System: Architecture: x86_64 CPU(s): 72 Model name: Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz 16 threads 400K requests/sec ============================= ------------------------------------------------------------------------------- Default Symmetric queues ------------------------------------------------------------------------------- RTT min/avg/max 4/51/2215 2/30/5163 (usec) intr/sec 26655 18606 contextswitch/sec 5145 4044 insn per cycle 0.43 0.72 cache-misses 6.919 4.310 (% of all cache refs) L1-dcache-load- 4.49 3.29 -misses (% of all L1-dcache hits) LLC-load-misses 13.26 8.96 (% of all LL-cache hits) ------------------------------------------------------------------------------- 32 threads 400K requests/sec ============================= ------------------------------------------------------------------------------- Default Symmetric queues ------------------------------------------------------------------------------- RTT min/avg/max 10/112/5562 9/46/4637 (usec) intr/sec 30456 27666 contextswitch/sec 7552 5133 insn per cycle 0.41 0.49 cache-misses 9.357 2.769 (% of all cache refs) L1-dcache-load- 4.09 3.98 -misses (% of all L1-dcache hits) LLC-load-misses 12.96 3.96 (% of all LL-cache hits) ------------------------------------------------------------------------------- 16 threads 800K requests/sec ============================= ------------------------------------------------------------------------------- Default Symmetric queues ------------------------------------------------------------------------------- RTT min/avg/max 5/151/4989 9/69/2611 (usec) intr/sec 35686 22907 contextswitch/sec 25522 12281 insn per cycle 0.67 0.74 cache-misses 8.652 6.38 (% of all cache refs) L1-dcache-load- 3.19 2.86 -misses (% of all L1-dcache hits) LLC-load-misses 16.53 11.99 (% of all LL-cache hits) ------------------------------------------------------------------------------- 32 threads 800K requests/sec ============================= ------------------------------------------------------------------------------- Default Symmetric queues ------------------------------------------------------------------------------- RTT min/avg/max 6/163/6152 8/88/4209 (usec) intr/sec 47079 26548 contextswitch/sec 42190 39168 insn per cycle 0.45 0.54 cache-misses 8.798 4.668 (% of all cache refs) L1-dcache-load- 6.55 6.29 -misses (% of all L1-dcache hits) LLC-load-misses 13.91 10.44 (% of all LL-cache hits) ------------------------------------------------------------------------------- v6: - Changed the names of some functions to begin with net_if. - Cleaned up sk_tx_queue_set/sk_rx_queue_set functions. - Added sk_rx_queue_clear to make it consistent with tx_queue_mapping initialization. ==================== Signed-off-by:
-
Amritha Nambiar authored
Signed-off-by:
Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by:
-
Amritha Nambiar authored
Extend transmit queue sysfs attribute to configure Rx queue(s) map per Tx queue. By default no receive queues are configured for the Tx queue. - /sys/class/net/eth0/queues/tx-*/xps_rxqs Signed-off-by:
-
Amritha Nambiar authored
This patch adds support to pick Tx queue based on the Rx queue(s) map configuration set by the admin through the sysfs attribute for each Tx queue. If the user configuration for receive queue(s) map does not apply, then the Tx queue selection falls back to CPU(s) map based selection and finally to hashing. Signed-off-by:
-
Amritha Nambiar authored
This patch adds a new field to sock_common 'skc_rx_queue_mapping' which holds the receive queue number for the connection. The Rx queue is marked in tcp_finish_connect() to allow a client app to do SO_INCOMING_NAPI_ID after a connect() call to get the right queue association for a socket. Rx queue is also marked in tcp_conn_request() to allow syn-ack to go on the right tx-queue associated with the queue on which syn is received. Signed-off-by:
Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by:
-
Amritha Nambiar authored
Change 'skc_tx_queue_mapping' field in sock_common structure from 'int' to 'unsigned short' type with ~0 indicating unset and other positive queue values being set. This will accommodate adding a new 'unsigned short' field in sock_common in the next patch for rx_queue_mapping. Signed-off-by:
-
Amritha Nambiar authored
Use static_key for XPS maps to reduce the cost of extra map checks, similar to how it is used for RPS and RFS. This includes static_key 'xps_needed' for XPS and another for 'xps_rxqs_needed' for XPS using Rx queues map. Signed-off-by:
-
Amritha Nambiar authored
Refactor XPS code to support Tx queue selection based on CPU(s) map or Rx queue(s) map. Signed-off-by:
-
- 30 Jun, 2018 20 commits
-
-
David S. Miller authored
Petr Machata says: ==================== mlxsw: Add resource scale tests There are a number of tests that check features of the Linux networking stack. By running them on suitable interfaces, one can exercise the mlxsw offloading code. However none of these tests attempts to push mlxsw to the limits supported by the ASIC. As an additional wrinkle, the "limits supported by the ASIC" themselves may not be a set of fixed numbers, but rather depend on a profile that determines how the ASIC resources are allocated for different purposes. This patchset introduces several tests that verify capability of mlxsw to offload amounts of routes, flower rules, and mirroring sessions that match predicted ASIC capacity, at different configuration profiles. Additionally they verify that amounts exceeding the predicted capacity can *not* be offloaded. These are not generic tests, but ones that are tailored for mlxsw specifically. For that reason they are not added to net/forwarding selftests subdirectory, but rather to a newly-added drivers/net/mlxsw. Patches #1, #2 and #3 tweak the generic forwarding/lib.sh to support the new additions. In patches #4 and #5, new libraries for interfacing with devlink are introduced, first a generic one, then a Spectrum-specific one. In patch #6, a devlink resource test is introduced. Patches #7 and #8, #9 and #10, and #11 and #12 introduce three scale tests: router, flower and mirror-to-gretap. The first of each pair of patches introduces a generic portion of the test (mlxsw-specific), the second introduces a Spectrum-specific wrapper. Patch #13 then introduces a scale test driver that runs (possibly a subset of) the tests introduced by patches from previous paragraph. ==================== Signed-off-by: -
Yuval Mintz authored
Add a scale test capable of validating that offloaded network functionality is indeed functional at scale when configured to the different KVD profiles available. Start by testing offloaded routes are functional at scale by passing traffic on each one of them in turn. Signed-off-by:
Yuval Mintz <yuvalm@mellanox.com> Signed-off-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
-
Petr Machata authored
Add a wrapper around mlxsw/mirror_gre_scale.sh that parameterized number of offloadable mirrors on Spectrum machines. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Petr Machata authored
Test that it's possible to offload a given number of mirrors. Signed-off-by:
-
Petr Machata authored
Add a wrapper around mlxsw/tc_flower_scale.sh that parameterizes the generic tc flower scale test template with Spectrum-specific target values. Signed-off-by:
-
Petr Machata authored
Add test of capacity to offload flower. This is a generic portion of the test that is meant to be called from a driver that supplies a particular number of rules to be tested with. Signed-off-by:
-
Yuval Mintz authored
IPv4 routes in Spectrum are based on the kvd single-hash, but as it's a hash we need to assume we cannot reach 100% of its capacity. Add a wrapper that provides us with good/bad target numbers for the Spectrum ASIC. Signed-off-by:
-
Arkadi Sharshevsky authored
This test aims for both stand alone and internal usage by the resource infra. The test receives the number routes to offload and checks: - The routes were offloaded correctly - Traffic for each route. Signed-off-by:
Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by:
-
Yuval Mintz authored
Add a selftest that can be used to perform basic sanity of the devlink resource API as well as test the behavior of KVD manipulation in the driver. This is the first case of a HW-only test - in order to test the devlink resource a driver capable of exposing resources has to be provided first. Signed-off-by:
-
Petr Machata authored
This library builds on top of devlink_lib.sh and contains functionality specific to Spectrum ASICs, e.g., re-partitioning the various KVD sub-parts. Signed-off-by:
-
Petr Machata authored
This helper library contains wrappers to devlink functionality agnostic to the underlying device. Signed-off-by:
-
Petr Machata authored
setup_wait() and tc_offload_check() both assume that all NUM_NETIFS interfaces are relevant for a given test. However, the scale test script acts as an umbrella for a number of sub-tests, some of which may not require all the interfaces. Thus it's suboptimal for tc_offload_check() to query all the interfaces. In case of setup_wait() it's incorrect, because the sub-test in question of course doesn't configure any interfaces beyond what it needs, and setup_wait() then ends up waiting indefinitely for the extraneous interfaces to come up. For that reason, give setup_wait() and tc_offload_check() an optional parameter with a number of interfaces to probe. Fall back to global NUM_NETIFS if the parameter is not given. Signed-off-by:
-
Petr Machata authored
In the scale testing scenarios, one usually has a condition that is expected to either fail, or pass, depending on which side of the scale is being tested. To capture this logic, add a function check_err_fail(), which dispatches either to check_err() or check_fail(), depending on the value of the first argument, should_fail. Signed-off-by:
-
Yuval Mintz authored
The devlink related scripts are mlxsw-specific. As a result, they'll reside in a different directory - but would still need the common logic implemented in lib.sh. So as a preliminary step, allow lib.sh to be sourced from other directories as well. Signed-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== nfp: flower updates and netconsole This set contains assorted updates to driver base and flower. First patch is a follow up to a fix to calculating counters which went into net. For ethtool counters we should also make sure they are visible even after ring reconfiguration. Next patch is a safety measure in case we are running on a machine with a broken BIOS we should fail the probe when risk of incorrect operation is too high. The next two patches add netpoll support and make use of napi_consume_skb(). Last we populate bus info on all representors. Pieter adds support for offload of the checksum action in flower. John follows up to another fix he's done in net, we set TTL values on tunnels to stack's default, now Johns does a full route lookup to get a more precise information, he populates ToS field as well. Last but not least he follows up on Jiri's request to enable LAG offload in case the team driver is used and then hash function is unknown. ==================== Signed-off-by: -
John Hurley authored
Currently the NFP fw only supports L3/L4 hashing so rejects the offload of filters that output to LAG ports implementing other hash algorithms. Team, however, uses a BPF function for the hash that is not defined. To support Team offload, accept hashes that are defined as 'unknown' (only Team defines such hash types). In this case, use the NFP default of L3/L4 hashing for egress port selection. Signed-off-by:
John Hurley <john.hurley@netronome.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
John Hurley authored
Extract the tos and the tunnel flags from the tunnel key and offload these action fields. Only the checksum and tunnel key flags are implemented in fw so reject offloads of other flags. The tunnel key flag is always considered set in the fw so enforce that it is set in the rule. Note that the compulsory setting of the tunnel key flag and optional setting of checksum is inline with how tc currently generates ipv4 udp tunnel actions. Signed-off-by:
-
John Hurley authored
Previously the ttl for ipv4 udp tunnels was set to the namespace default. Modify this to attempt to extract the ttl from a full route lookup on the tunnel destination. If this is not possible then resort to the default. Signed-off-by:
-
Pieter Jansen van Vuuren authored
Hardware will automatically update csum in headers when a set action has been performed. This means we could in the driver ignore the explicit checksum action when performing a set action. Signed-off-by:
Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by:
-
Jakub Kicinski authored
We used to leave bus-info in ethtool driver info empty for representors in case multi-PCIe-to-single-host cards make the association between PCIe device and NFP many to one. It seems these attempts are futile, we need to link the representors to one PCIe device in sysfs to get consistent naming, plus devlink uses one PCIe as a handle, anyway. The multi-PCIe-to-single-system support won't be clean, if it ever comes. Turns out some user space (RHEL tests) likes to read bus-info so just populate it. While at it remove unnecessary app NULL-check, representors are spawned by an app, so it must exist. Signed-off-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
-
