Switch the device tree to the new compatibles introduced in the ethernet and
mdio drivers to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the mdio driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesse Gross says:

====================
Open vSwitch

A handful of bug fixes for net/3.14. High level fixes are:
 * Regressions introduced by the zerocopy changes, particularly with
   old userspaces.
 * A few bugs lingering from the introduction of megaflows.
 * Overly zealous error checking that is now being triggered frequently
   in common cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent patch to fix receive side flow control
(11b57f90: xen-netback: stop vif thread
spinning if frontend is unresponsive) solved the spinning thread problem,
however caused an another one. The receive side can stall, if:
- [THREAD] xenvif_rx_action sets rx_queue_stopped to true
- [INTERRUPT] interrupt happens, and sets rx_event to true
- [THREAD] then xenvif_kthread sets rx_event to false
- [THREAD] rx_work_todo doesn't return true anymore

Also, if interrupt sent but there is still no room in the ring, it take quite a
long time until xenvif_rx_action realize it. This patch ditch that two variable,
and rework rx_work_todo. If the thread finds it can't fit more skb's into the
ring, it saves the last slot estimation into rx_last_skb_slots, otherwise it's
kept as 0. Then rx_work_todo will check if:
- there is something to send to the ring (like before)
- there is space for the topmost packet in the queue

I think that's more natural and optimal thing to test than two bool which are
set somewhere else.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With subfacets, we'd expect megaflow updates message to carry
the original micro flow. If not, EINVAL is returned and kernel
logs an error message.  Now that the user space subfacet layer is
removed, it is expected that flow updates can arrive with a
micro flow other than the original. Change the return code to
EEXIST and remove the kernel error log message.
Reported-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

ovs_flow_free() is not called under ovs-lock during packet
execute path (ovs_packet_cmd_execute()). Since packet execute
does not touch flow->mask, there is no need to take that
lock either. So move assert in case where flow->mask is checked.

Found by code inspection.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

commit 43d4be9c (openvswitch: Allow user space
to announce ability to accept unaligned Netlink messages) introduced
OVS_DP_ATTR_USER_FEATURES netlink attribute in datapath responses,
but the attribute size was not taken into account in ovs_dp_cmd_msg_size().
Signed-off-by: Daniele Di Proietto <daniele.di.proietto@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

Both mega flow mask's reference counter and per flow table mask list
should only be accessed when holding ovs_mutex() lock. However
this is not true with ovs_flow_table_flush(). The patch fixes this bug.
Reported-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

While the zerocopy method is correctly omitted if user space
does not support unaligned Netlink messages. The attribute is
still not padded correctly as skb_zerocopy() will not ensure
padding and the attribute size is no longer pre calculated
though nla_reserve() which ensured padding previously.

This patch applies appropriate padding if a linear data copy
was performed in skb_zerocopy().
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED.  If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.

So, treat an unexpected backend CLOSED state the same as CLOSING.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configuring GRE tunnel using OVS, tcp stream is distributed over
all RSS queues which may cause TCP reordering. It happens since OVS
uses L2GRE protocol when kernel gre uses IPGRE.
Patch defaults gre tunnel to L2GRE which allows proper RSS for L2GRE
packets and (implicitly) disables RSS for IPGRE traffic.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This device was mentioned in an OpenWRT forum.  Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
 0: qcdm
 2: nmea
 3: modem
 8: qmi
 9: storage
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should check whether rtnetlink link operations
are defined before calling get_slave_size().

Without this, the following oops can occur when
adding a tap device to OVS.

[   87.839553] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
[   87.839595] IP: [<ffffffff813d47c0>] if_nlmsg_size+0xf0/0x220
[...]
[   87.840651] Call Trace:
[   87.840664]  [<ffffffff813d694b>] ? rtmsg_ifinfo+0x2b/0x100
[   87.840688]  [<ffffffff813c8340>] ? __netdev_adjacent_dev_insert+0x150/0x1a0
[   87.840718]  [<ffffffff813d6a50>] ? rtnetlink_event+0x30/0x40
[   87.840742]  [<ffffffff814b4144>] ? notifier_call_chain+0x44/0x70
[   87.840768]  [<ffffffff813c8946>] ? __netdev_upper_dev_link+0x3c6/0x3f0
[   87.840798]  [<ffffffffa0678d6c>] ? netdev_create+0xcc/0x160 [openvswitch]
[   87.840828]  [<ffffffffa06781ea>] ? ovs_vport_add+0x4a/0xd0 [openvswitch]
[   87.840857]  [<ffffffffa0670139>] ? new_vport+0x9/0x50 [openvswitch]
[   87.840884]  [<ffffffffa067279e>] ? ovs_vport_cmd_new+0x11e/0x210 [openvswitch]
[   87.840915]  [<ffffffff813f3efa>] ? genl_family_rcv_msg+0x19a/0x360
[   87.840941]  [<ffffffff813f40c0>] ? genl_family_rcv_msg+0x360/0x360
[   87.840967]  [<ffffffff813f4139>] ? genl_rcv_msg+0x79/0xc0
[   87.840991]  [<ffffffff813b6cf9>] ? __kmalloc_reserve.isra.25+0x29/0x80
[   87.841018]  [<ffffffff813f2389>] ? netlink_rcv_skb+0xa9/0xc0
[   87.841042]  [<ffffffff813f27cf>] ? genl_rcv+0x1f/0x30
[   87.841064]  [<ffffffff813f1988>] ? netlink_unicast+0xe8/0x1e0
[   87.841088]  [<ffffffff813f1d9a>] ? netlink_sendmsg+0x31a/0x750
[   87.841113]  [<ffffffff813aee96>] ? sock_sendmsg+0x86/0xc0
[   87.841136]  [<ffffffff813c960d>] ? __netdev_update_features+0x4d/0x200
[   87.841163]  [<ffffffff813ca94e>] ? ethtool_get_value+0x2e/0x50
[   87.841188]  [<ffffffff813af269>] ? ___sys_sendmsg+0x359/0x370
[   87.841212]  [<ffffffff813da686>] ? dev_ioctl+0x1a6/0x5c0
[   87.841236]  [<ffffffff8109c210>] ? autoremove_wake_function+0x30/0x30
[   87.841264]  [<ffffffff813ac59d>] ? sock_do_ioctl+0x3d/0x50
[   87.841288]  [<ffffffff813aca68>] ? sock_ioctl+0x1e8/0x2c0
[   87.841312]  [<ffffffff811934bf>] ? do_vfs_ioctl+0x2cf/0x4b0
[   87.841335]  [<ffffffff813afeb9>] ? __sys_sendmsg+0x39/0x70
[   87.841362]  [<ffffffff814b86f9>] ? system_call_fastpath+0x16/0x1b
[   87.841386] Code: c0 74 10 48 89 ef ff d0 83 c0 07 83 e0 fc 48 98 49 01 c7 48 89 ef e8 d0 d6 fe ff 48 85 c0 0f 84 df 00 00 00 48 8b 90 08 07 00 00 <48> 8b 8a a8 00 00 00 31 d2 48 85 c9 74 0c 48 89 ee 48 89 c7 ff
[   87.841529] RIP  [<ffffffff813d47c0>] if_nlmsg_size+0xf0/0x220
[   87.841555]  RSP <ffff880221aa5950>
[   87.841569] CR2: 00000000000000a8
[   87.851442] ---[ end trace e42ab217691b4fc2 ]---
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the trigger/event is hardcoded to 0, this patch adds
a new command line argument -i to select an arbitrary trigger/
event.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MII management bus clock is derived from the MAC clock by dividing it by
MIIMODER register CLKDIV field value. This value may need to be set up
in case it is undefined or its default value is too high (and
communication with PHY is too slow) or too low (and communication with
PHY is impossible). The value of CLKDIV is not specified directly, but
is derived from the MAC clock for the default MII management bus frequency
of 2.5MHz. The MAC clock may be specified in the platform data, or in
the 'clocks' device tree attribute.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does
not disable advertisement when PHY supports them. This results in
non-functioning network when the MAC is connected to a gigabit PHY connected
to a gigabit switch.

The fix is to disable gigabit speed advertisement on attached PHY
unconditionally.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.

This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The trigger and events functionality can be useful even if packet
timestamping is not used, but the required PTP clock is only enabled
when packet timestamping is started. This patch moves the clock enable
to when the interface is configured.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the external timestamping code is hardcoded to use the
rising edge even though the hardware has configurable event edge
detection. This patch changes the code to use falling edge detection
if PTP_FALLING_EDGE is set in the user supplied flags.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the SKBTX_IN_PROGRESS bit in tx_flags dp83640_txtstamp when doing
tx timestamps as per Documentation/networking/timestamping.txt.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RCU writer side should use rcu_dereference_protected() and not
rcu_dereference(), fix that. This also removes the "suspicious RCU usage"
warning seen when running with CONFIG_PROVE_RCU.

Also, don't use rcu_assign_pointer/rcu_dereference for pointers
which are invisible beyond the udp offload code.

Fixes: b582ef09 ('net: Add GRO support for UDP encapsulating protocols')
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ding Tianhong says:

====================
bonding: Fix some issues for fail_over_mac

The parameter fail_over_mac only affect active-backup mode, if it was
set to active or follow and works with other modes, just like RR or XOR
mode, the bonding could not set all slaves to the master's address, it
will cause the slave could not work well with master.

v1->v2: According Jay's suggestion, that we should permit setting an option
	at any time, but only have it take effect in active-backup mode, so
	I add mode checking together with fail_over_mac during enslavement and
	rebuild the patches.

v2->v3: The correct way to fix the problem is that we should not add restrictions when
    	setting options, just need to modify the bond enslave and removal processing
    	to check the mode in addition to fail_over_mac when setting a slave's MAC during
    	enslavement. The change active slave processing already only calls the fail_over_mac
    	function when in active-backup mode.

	Remove the cleanup patch because the net-next is frozen now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>

The fail_over_mac could be set to active or follow in any time for all modes,
so if the fail_over_mac is not none and the current mode is not active-backup,
the bond_set_mac_address() could not change the master and slave's MAC address.

In bond_set_mac_address(), the fail_over_mac should only affect AB mode, so modify
to check the mode in addition to fail_over_mac when setting bond's MAC address.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to bonding.txt, the fail_over_ma should only affect active-backup mode,
but I found that the fail_over_mac could be set to active or follow in all
modes, this will cause new slave could not be set to bond's MAC address at
enslave processing and restore its own MAC address at removal processing.

The correct way to fix the problem is that we should not add restrictions when
setting options, just need to modify the bond enslave and removal processing
to check the mode in addition to fail_over_mac when setting a slave's MAC during
enslavement. The change active slave processing already only calls the fail_over_mac
function when in active-backup mode.

Thanks for Jay's suggestion.

The patch also modify the pr_warning() to pr_warn().

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting rt variable to NULL at the beginning of ip_tunnel_xmit()
missed possible use of this variable as a scratch value.

Also fixes a possible dst leak in tunnel_dst_check() :
If we had to call tunnel_dst_reset(), we forgot to
release the reference on dst.

Merges tunnel_dst_get()/tunnel_dst_check() into
a single tunnel_rtable_get() function for clarity.

Many thanks to Tommi for his report and tests.

Fixes: 7d442fab ("ipv4: Cache dst in tunnels")
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Tommi Rantala <tt.rantala@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Max Filippov says:

====================
OpenCores 10/100 MAC ethtool operations

this series implements ethtool callbacks for the ethoc driver as was
requested by Florian.

Changes v1->v2:
- fix {get,set}_settings return code in case there's no PHY;
- fix set_ringparam: check ring sizes, change ring sizes on the fly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

TX and RX rings share memory and descriptors. Maximal number of
descriptors reported is one less than the total available nuber of
descriptors. For the set operation the requested number of TX descriptors
is rounded down to the nearest power of two (driver logic requirement).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following methods are implemented:
- get link state (standard implementation);
- get timestamping info (standard implementation).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

linux-can-fixes-for-3.14-20140129

Marc Kleine-Budde says:

====================
Arnd Bergmann provides a fix for the flexcan driver, enabling compilation on
all combinations of big and little endian on ARM and PowerPc. A patch by Ira W.
Snyder fixes uninitialized variable warnings in the janz-ican3 driver.
Rostislav Lisovy contributes a patch to propagate the SO_PRIORITY of raw
sockets to skbs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In https://bugzilla.redhat.com/show_bug.cgi?id=994438 and
https://bugzilla.redhat.com/show_bug.cgi?id=970480  we
received different reports of e100 throwing the following
warning:

 [<c06a0ba5>] ? pci_disable_device+0x85/0x90
 [<c044a153>] warn_slowpath_fmt+0x33/0x40
 [<c06a0ba5>] pci_disable_device+0x85/0x90
 [<f7fdf7e0>] __e100_shutdown+0x80/0x120 [e100]
 [<c0476ca5>] ? check_preempt_curr+0x65/0x90
 [<f7fdf8d6>] e100_suspend+0x16/0x30 [e100]
 [<c06a1ebb>] pci_legacy_suspend+0x2b/0xb0
 [<c098fc0f>] ? wait_for_completion+0x1f/0xd0
 [<c06a2d50>] ? pci_pm_poweroff+0xb0/0xb0
 [<c06a2de4>] pci_pm_freeze+0x94/0xa0
 [<c0767bb7>] dpm_run_callback+0x37/0x80
 [<c076a204>] ? pm_wakeup_pending+0xc4/0x140
 [<c0767f12>] __device_suspend+0xb2/0x1f0
 [<c076806f>] async_suspend+0x1f/0x90
 [<c04706e5>] async_run_entry_fn+0x35/0x140
 [<c0478aef>] ? wake_up_process+0x1f/0x40
 [<c0464495>] process_one_work+0x115/0x370
 [<c0462645>] ? start_worker+0x25/0x30
 [<c0464dc5>] ? manage_workers.isra.27+0x1a5/0x250
 [<c0464f6e>] worker_thread+0xfe/0x330
 [<c0464e70>] ? manage_workers.isra.27+0x250/0x250
 [<c046a224>] kthread+0x94/0xa0
 [<c0997f37>] ret_from_kernel_thread+0x1b/0x28
 [<c046a190>] ? insert_kthread_work+0x30/0x30

This patch removes pci_disable_device() from __e100_shutdown().
pci_clear_master() is enough.
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Mark Harig <idirectscm@aim.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Self generated skbuffs in net/can/bcm.c are setting a skb->sk reference but
no explicit destructor which is enforced since Linux 3.11 with commit
376c7311 (net: add a temporary sanity check in skb_orphan()).

This patch adds some helper functions to make sure that a destructor is
properly defined when a sock reference is assigned to a CAN related skb.
To create an unshared skb owned by the original sock a common helper function
has been introduced to replace open coded functions to create CAN echo skbs.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Andre Naujoks <nautsch2@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The loop in vxlan_gro_receive() over the current set of candidates for
coalescing was wrongly aborted once a match was found. In rare cases,
this can cause a false-positives matching in the next layer GRO checks.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since udp_add_offload() can be called from non-sleepable context e.g
under this call tree from the vxlan driver use case:

  vxlan_socket_create() <-- holds the spinlock
  -> vxlan_notify_add_rx_port()
     -> udp_add_offload()  <-- schedules

we should allocate the udp_offloads structure in atomic manner.

Fixes: b582ef09 ('net: Add GRO support for UDP encapsulating protocols')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the GPIO bitbang MDIO driver is used instead of the Davinci MDIO driver
we need to configure the phy_id string differently. Otherwise this string
looks like this "gpio.6" instead of "gpio-0" and the PHY is not found when
phy_connect() is called.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block IO driver changes from Jens Axboe:

 - bcache update from Kent Overstreet.

 - two bcache fixes from Nicholas Swenson.

 - cciss pci init error fix from Andrew.

 - underflow fix in the parallel IDE pg_write code from Dan Carpenter.
   I'm sure the 1 (or 0) users of that are now happy.

 - two PCI related fixes for sx8 from Jingoo Han.

 - floppy init fix for first block read from Jiri Kosina.

 - pktcdvd error return miss fix from Julia Lawall.

 - removal of IRQF_SHARED from the SEGA Dreamcast CD-ROM code from
   Michael Opdenacker.

 - comment typo fix for the loop driver from Olaf Hering.

 - potential oops fix for null_blk from Raghavendra K T.

 - two fixes from Sam Bradshaw (Micron) for the mtip32xx driver, fixing
   an OOM problem and a problem with handling security locked conditions

* 'for-3.14/drivers' of git://git.kernel.dk/linux-block: (47 commits)
  mg_disk: Spelling s/finised/finished/
  null_blk: Null pointer deference problem in alloc_page_buffers
  mtip32xx: Correctly handle security locked condition
  mtip32xx: Make SGL container per-command to eliminate high order dma allocation
  drivers/block/loop.c: fix comment typo in loop_config_discard
  drivers/block/cciss.c:cciss_init_one(): use proper errnos
  drivers/block/paride/pg.c: underflow bug in pg_write()
  drivers/block/sx8.c: remove unnecessary pci_set_drvdata()
  drivers/block/sx8.c: use module_pci_driver()
  floppy: bail out in open() if drive is not responding to block0 read
  bcache: Fix auxiliary search trees for key size > cacheline size
  bcache: Don't return -EINTR when insert finished
  bcache: Improve bucket_prio() calculation
  bcache: Add bch_bkey_equal_header()
  bcache: update bch_bkey_try_merge
  bcache: Move insert_fixup() to btree_keys_ops
  bcache: Convert sorting to btree_keys
  bcache: Convert debug code to btree_keys
  bcache: Convert btree_iter to struct btree_keys
  bcache: Refactor bset_tree sysfs stats
  ...