Merge tag 'renesas-dt-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

From Simon Horman:
Renesas ARM based SoC DT updates for v3.14

* Global
  - Use interrupt macros
  - Use #include in device tree sources
  - Tidyup DT node naming

* emev2 (Emma Mobile EV2) SoC
  - Setup internal peripheral interrupts as level high
  - Use interrupt macros in DT files
  - Add clock tree description in DT

* r8a7791 (R-Car M2) SoC
  - Correct GPIO resources

* r8a7791 (R-Car M2) based Koelsch board
  - Configure PFC and GPO
  - Use r8a7791 suffix for IRQC compat string
  - Add DT reference

* r8a7790 (R-Car H2) based Lager board
  - Include all 4 GiB of memory
  - Use r8a7790 suffix for IRQC and MMCIF compat strings
  - Enable MMCIF
  - Add default PFC settings

* r8a7778 (R-Car M1) SoC
  - Suffix for INTC compat string
  - Add HSPI, MMCIF, SDHI and I2C suppport on DTSI
  - Correct pin control device addresses

* r8a7778 (R-Car M1) based Bock-W board
  - Use falling edge IRQ for LAN9221 in DT reference
  - Enable I2C, HSPI0, MMCIF and SDHI
  - Correct MMC pin conflict
  - Remove manual PFC settings from DT reference
  - Add default PFC settings

* r8a7779 (R-Car H1) SoC
  - Add HSPI and SDHI support
  - Suffix for INTC compat string

* r8a7779 (R-Car H1) based Marzen board
  - Enable HSPI0 and SDHI in DTS
  - Remove SDHI0 WP pin setting
  - Use falling edge IRQ for LAN9221 in DT reference
  - Add SDHI support

* r8a7740 (R-Mobile A1) SoC
  - Suffix for INTC compat string
  - Add FSI support via DTSI
  - Use interrupt macros

* r8a7740 based Armadillo board
  - Add FSI support for DTS
  - Use low level IRQ for ST1231 in DT reference

* r8a73a4 (SH-Mobile APE6) SoC
  - Use interrupt macros in DT files

* r8a73a4 (R-Mobile APE6) based ape6evm board
  - Include all 2 GiB of memory

* r8a73a0 (SH-Mobile AG5) SoC
  - Correct SDHI compat string

* r8a73a0 (SH-Mobile AG5) based kzm9d board
  - Add GPIO keys and Add PCF8575 GPIO extender to DT
  - Enable DSW2 with gpio-keys
  - Use falling edge IRQ for LAN9221 in DT reference

* tag 'renesas-dt-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (102 commits)
  ARM: shmobile: marzen: enable HSPI0 in DTS
  ARM: shmobile: r8a7779: add HSPI support to DTSI
  ARM: shmobile: Use r8a7779 suffix for INTC compat string
  ARM: shmobile: Use r8a7778 suffix for INTC compat string
  ARM: shmobile: Use r8a7740 suffix for INTC compat string
  ARM: shmobile: Use sh73a0 suffix for INTC compat string
  ARM: shmobile: armadillo: add FSI support for DTS
  ARM: shmobile: r8a7740: add FSI support via DTSI
  ARM: shmobile: emev2: Setup internal peripheral interrupts as level high
  ARM: shmobile: emev2: Use interrupt macros in DT files
  ARM: shmobile: Use interrupt macros in r8a73a4 and r8a7778 DT files
  ARM: shmobile: Fix r8a7791 GPIO resources in DTS
  ARM: shmobile: Include all 4 GiB of memory on Lager DT Ref
  ARM: shmobile: Include all 4 GiB of memory on Lager
  ARM: shmobile: Include all 2 GiB of memory on APE6EVM
  ARM: shmobile: Include all 2 GiB of memory on APE6EVM DT Ref
  ARM: shmobile: kzm9g-reference: Add GPIO keys to DT
  ARM: shmobile: kzm9g-reference: Add PCF8575 GPIO extender to DT
  ARM: shmobile: Koelsch DT reference GPIO LED support
  ARM: shmobile: Enable DSW2 with gpio-keys on KZM9D
  ...
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Merge tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt

Keystone DTS updates for 3.14

- ddr3 pll clock node typo fixup.
- EVM specific clock setting with board k2hk-evm.dts.
- GIC node updates for missing virtualisation info.
- Adding USB dwc3 and phy nodes.

* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone: Add usb devicetree bindings
  ARM: dts: keystone: Add usb phy devicetree bindings
  ARM: dts: keystone: Add guestos maintenance interrupt
  ARM: dts: keystone: Add the GICV and GICH address space
  ARM: keystone: dts: add paclk divider clock node
  ARM: keystone: dts: fix typo in the ddr3 pllclk node name
  ARM: keystone: dts: add a k2hk-evm specific dts file
Signed-off-by: Kevin Hilman <khilman@linaro.org>

* mvebu/dt-4:
  ARM: mvebu: sort DT nodes by address
  ARM: orion5x: sort DT nodes by address
  ARM: dove: sort DT nodes by address
  ARM: kirkwood: sort dt nodes by address
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Conflicts:
	arch/arm/boot/dts/armada-370-xp.dtsi

From Jason Cooper:
mvebu DT changes for v3.14 (incr. #3)

 - kirkwood
    - use symbolic names for gpios and key inputs

 - mvebu
    - add the pxa nand controller to the ReadyNAS and A370-RD boards

* tag 'mvebu-dt-3.14-3' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Enable NAND controller in A370 Reference Design board
  ARM: mvebu: Enable NAND controller in ReadyNAS 2120 .dts file
  ARM: mvebu: Enable NAND controller in ReadyNAS 104 .dts file
  ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file
  ARM: DT: Kirkwood: Use symbolic names from gpio.h
  ARM: DT: Kirkwood: Use symbolic names from input.h
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Merge tag 'nomadik-dt-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt

From Linus Walleij:
Some Nomadik Device Tree updates for the v3.14 cycle:

- Drop 0x prefixes

- Get rid of explicit GPIO management

* tag 'nomadik-dt-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: nomadik: get rid of explicit ethernet GPIO management
  ARM: nomadik: Remove '0x's from nomadik stn8815 DTS file

Added device tree support for TI's Keystone USB driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Added device tree support for TI's Keystone USB PHY driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Update the Keystone gic device tree entry to add the maintenance
interrupt information.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Update the Keystone gic node to add the GICV and GIGH address space
needed by the KVM.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

PA subsystem has a fixed factor clock at the input which is
input clock divided by 3. This patch adds this clock node to dts
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Fix following typo
 ddr3allclk -> ddr3apllclk
 ddr3bllclk -> ddr3bpllclk
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

This patch adds K2 Kepler/Hawking evm (k2hk-evm) specific dts file.
To enable re-use of bindings across multiple evms of this family,
rename current keystone.dts to keystone.dtsi and include it in the
evm specific dts file.

K2 SoC has separate ref clock inputs for various clocks. So add
separate ref clock nodes for ARM, DDR3A, DDR3B and PA PLL input
clocks in k2hk-evm.dts. While at it, rename  refclkmain to
refclksys based on device User Guide naming convention
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Prevent future unnecessary merge conflicts
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Prevent future unnecessary merge conflicts
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Prevent future (unnecessary) merge conflicts
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This has caused merge conflicts in the past.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Marvell's Armada 370 Reference Design has a NAND flash, so enable it in
the devicetree and add the partitions as prepared in the factory images.

In order to skip the driver's custom device detection and use only ONFI
detection, the "marvell,keep-config" parameter is used. This is needed
because we have no support for setting the timings parameters yet.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch adds PWM nodes for each of the four channels present on the
pxa270.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'integrator-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt

From Linus Walleij:
Two integrator device tree patches for v3.14:

- Delete some static core module mappings.

- Move EBI location to the device tree.

* tag 'integrator-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: integrator: move EBI to the device tree
  ARM: integrator: delete static core module mappings
Signed-off-by: Kevin Hilman <khilman@linaro.org>

From Nicolas Ferre:
First DT pull-request for 3.14
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board

* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
  ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order
  ARM: at91: dt: at91rm9200ek: add emac and nor flash support
  ARM: at91: add uart aliases to sama5d3 dtsi
  ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT
  ARM: at91: Animeo IP: fix mtd partition table
  ARM: at91: at91sam9g45: add i2c pinctrl
  ARM: at91: at91sam9g45: set default mmc pinctrl-names
  ARM: at91: sama5d3: enable qt1070 as a wakeup source
  ARM: at91: add support for Cosino board series by HCE Engineering
  ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes
  ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix
  ARM: at91/dt/trivial: use macro for AES irq type
  ARM: at91: sam9263ek: add dt lcd support
  ARM: at91: at9sam9m10g45ek: add dt lcd support
  ARM: at91: sam9263: add fb dt support
  ARM: at91: sam9g45: add fb dt support
  ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation
  ARM: at91/dt: binding: add precision to AIC documentation
  ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition
  ARM: at91/dt: add ethernet phy to at91rm9200ek board
  ...
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Add .dts and .dtsi file to support sama5d36ek board.
Also update the the comments for sama5d36 in sama5d3.dtsi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>

From Jason Cooper:
mvebu DT changes for v3.14 (set #2)

 - mvebu
    - Netgear ReadyNAS cleanup
    - add Netgear ReadyNAS 2120

 - kirkwood
    - Netgear ReadyNAS cleanup
    - add Netgear ReadyNAS NV+ v2

* tag 'mvebu-dt-3.14-2' of git://git.infradead.org/linux-mvebu:
  ARM: kirkwood: Add support for NETGEAR ReadyNAS NV+ v2
  ARM: mvebu: Add Netgear ReadyNAS 2120 board
  ARM: mvebu: Fix whitespace in NETGEAR ReadyNAS .dts files
  ARM: mvebu: NETGEAR ReadyNAS 104 .dts cleanup
  ARM: mvebu: NETGEAR ReadyNAS 102 .dts cleanup
  ARM: kirkwood: NETGEAR ReadyNAS Duo v2 .dts cleanup
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Based on work for the bockw board by Kuninori Morimoto.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Based on work for the r8a7778 SoC by Kuninori Morimoto.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "renesas,intc-irqpin-r8a7779" to the compatible string for the
IRQ pins in case of r8a7779 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "renesas,intc-irqpin-r8a7778" to the compatible string for the
IRQ pins in case of r8a7778 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "renesas,intc-irqpin-r8a7740" to the compatible string for the
IRQ pins in case of r8a7740 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "renesas,intc-irqpin-sh73a0" to the compatible string for the
IRQ pins in case of sh73a0 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch support FSI-WM8978 with simple audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Interrupts generated by SoC internal devices are currently marked as
IRQ_TYPE_NONE. As they're level-triggered and active-high, mark them as
such.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The r8a7791 GPIO resources are currently incorrect. Fix that
by making them match the English r8a7791 v0.31 data sheet.

Tested with GPIO LED using Koelsch DT reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms@verge.net.au>

Add 2GiB of DRAM at 0x1_8000_0000 to support the full 4GiB
of Lager system memory in case of DT Reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add 2GiB of DRAM at 0x1_8000_0000 to support the full 4GiB
of Lager system memory.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add 1GiB of DRAM at 0x2_0000_0000 to support the full 2GiB
of APE6EVM system memory.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add 1GiB of DRAM at 0x2_0000_0000 to support the full 2GiB
of APE6EVM system memory also in case of DT reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>