The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively.  The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954.  The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allows tuning of the RX FIFO fill threshold and timeout. (The latter is
only applicable to SCIFA and SCIFB).
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implements support for FIFO fill thresholds greater than one with software
timeout.

This mechanism is not possible (or at least not useful) on SCIF family
hardware other than SCIFA and SCIFB because they do not support turning off
the DR hardware timeout interrupt separately from the RI interrupt.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sets reasonable trigger defaults for the various SCIF variants.
Also corrects the FIFO size for SH7705-style ports.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Register a serdev controller with the serdev bus when a tty_port is
registered. This creates the serdev controller and create's serdev
devices for any DT child nodes of the tty_port's parent (i.e. the UART
device).
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a serdev controller driver for tty ports.

The controller is registered with serdev when tty ports are registered
with the TTY core. As the TTY core is built-in only, this has the side
effect of making serdev built-in as well.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The serdev bus is designed for devices such as Bluetooth, WiFi, GPS
and NFC connected to UARTs on host processors. Tradionally these have
been handled with tty line disciplines, rfkill, and userspace glue such
as hciattach. This approach has many drawbacks since it doesn't fit
into the Linux driver model. Handling of sideband signals, power control
and firmware loading are the main issues.

This creates a serdev bus with controllers (i.e. host serial ports) and
attached devices. Typically, these are point to point connections, but
some devices have muxing protocols or a h/w mux is conceivable. Any
muxing is not yet supported with the serdev bus.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a common binding for describing serial/UART attached devices. Common
examples are Bluetooth, WiFi, NFC and GPS devices.

Serial attached devices are represented as child nodes of a UART node.
This may need to be extended for more complex devices with multiple
interfaces, but for the simple cases a child node is sufficient.
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a client (upward direction) operations struct for tty_port
clients. Initially supported operations are for receiving data and write
wake-up. This will allow for having clients other than an ldisc.

Convert the calls to the ldisc to use the client ops as the default
operations.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sets the closest match for a desired RX trigger level.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To allow operation with a higher RX FIFO interrupt threshold in PIO
mode, it is necessary to consider the DR bit ("FIFO not full, but no
data received for 1.5 frames") as an indicator that data can be read.
Otherwise the driver will let data rot in the FIFO until the threshold
is reached.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Defines the bits controlling FIFO thresholds, adds the additional
HSCIF registers to the register map.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of open-coding loop with of_find_node_by_type(), let's use canned
macro.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit c7cef0a8 ("console: Add extensible console matching") added
match() method to struct console which allows the console to perform
console command line matching instead of (or in addition to) default
console matching (ie., by fixed name and index).

Commit ad1696f6 ("ACPI: parse SPCR and enable matching console")
introduced support for SPCR as matching console.

Commit 10879ae5 ("serial: pl011: add console matching function")
added the match method for pl011 console which checks for the console
string to be "pl011"

Now on a platform which has both SPCR in the ACPI tables and ttyAMA in
the command line, the ttyAMA is chosen as "selected console" but it
doesn't pass the matching console method which results in CON_CONSDEV
not being set on the "selected console".

As a result of that, the bootconsole(SPCR in the above case) is not
unregistered and all the beginning boot messages are seen twice.

This patch adds "ttyAMA" so that it's considered to match pl011 console.

Fixes: 10879ae5 ("serial: pl011: add console matching function")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Ensure that the uart clock is enabled prior to writing to the
interrupt mask register in s3c24xx_serial_resume_noirq function.
Without enabing the uart clock, the uart register cannot be accessed.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the Exar specific codes from 8250_pci and blacklist those chips
so that the new Exar serial driver binds to the devices.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the serial driver for the Exar chips. And also register the
platform device for the GPIO provided by the Exar chips.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When userspace passes the SER_RS485_RTS_ON_SEND flag it means that the
CTS_B pin should go to logic level high before the transmission begins.

CTS_B goes to logic level high when both CTSC and CTS bits are cleared.

When userspace passes the SER_RS485_RTS_AFTER_SEND flag it means that the
CTS_B pin should go to logic level low after the transmission finishes.

CTS_B goes to logic level low when CTSC bit is cleared and CTS bit is set.

So fix the CTS_B polarity logic.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On a board that needs to drive RTS GPIO high in order to enable the
transmission of a RS485 transceiver the following description is
passed in the devide tree:

&uart4 {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_uart4>;
        rts-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
        status = "okay";
};

and userspace configures the uart port as follows:

/* enable RS485 mode: */
rs485conf.flags |= SER_RS485_ENABLED;

/* set logical level for RTS pin equal to 1 when sending: */
rs485conf.flags |= SER_RS485_RTS_ON_SEND;

/* set logical level for RTS pin equal to 0 after sending: */
rs485conf.flags &= ~(SER_RS485_RTS_AFTER_SEND);

However the RTS GPIO polarity observed in the oscilloscope is inverted.

When the SER_RS485_RTS_ON_SEND flag is set the imx_port_rts_active()
function should be called and following the same logic when
SER_RS485_RTS_AFTER_SEND flag is cleared the imx_port_rts_inactive()
should be called.

Do such logic change so that RS485 communication in half duplex can
work successfully when the RTS GPIO pin is passed via device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

During build testing, I ran into a warning in a driver that I
had written myself at some point:

drivers/tty/serial/8250/8250_of.c: In function 'of_platform_serial_probe':
drivers/tty/serial/8250/8250_of.c:233:1: error: the frame size of 1200 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]

This is harmless by itself, but it shows two other problems in
the driver:

- It still tries to be generic enough to handle all kinds of serial
  ports, where in reality the driver has been 8250-only for a while,
  and every other uart has its own DT support

- As a result of that generalization, we keep two copies of
  'struct uart_port' on the stack during probe(). This is completely
  unnessary.

Removing the last code dealing with unsupported port_type values
solves both problems nicely, and reduces the stack size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As the function header of sci_parse_dt() is split in an unusual way,
"git diff" gets confused when changes to the body of the function are
made, and attributes them to the wrong function.

Reformat the function header to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Declare uart_ops structures as const as they are only stored in the ops
field of an uart_port structure. This field is of type const, so
uart_ops structures having this property can be made const too.

File size details before and after patching.
First line of every .o file shows the file size before patching
and second line shows the size after patching.

   text	   data	    bss	    dec	    hex	filename

   2977	    456	     64	   3497	    da9	drivers/tty/serial/amba-pl010.o
   3169	    272	     64	   3505	    db1	drivers/tty/serial/amba-pl010.o

   3109	    456	      0	   3565	    ded	drivers/tty/serial/efm32-uart.o
   3301	    272	      0	   3573	    df5	drivers/tty/serial/efm32-uart.o

  10668	    753	      1	  11422	   2c9e	drivers/tty/serial/icom.o
  10860	    561	      1	  11422	   2c9e	drivers/tty/serial/icom.o

  23904	    408	      8	  24320	   5f00	drivers/tty/serial/ioc3_serial.o
  24088	    224	      8	  24320	   5f00	drivers/tty/serial/ioc3_serial.o

  10516	    560	      4	  11080	   2b48	drivers/tty/serial/ioc4_serial.o
  10709	    368	      4	  11081	   2b49	drivers/tty/serial/ioc4_serial.o

   7853	    648	   1216	   9717	   25f5	drivers/tty/serial/mpsc.o
   8037	    456	   1216	   9709	   25ed	drivers/tty/serial/mpsc.o

  10248	    456	      0	  10704	   29d0	drivers/tty/serial/omap-serial.o
  10440	    272	      0	  10712	   29d8	drivers/tty/serial/omap-serial.o

   8122	    532	   1984	  10638	   298e	drivers/tty/serial/pmac_zilog.o
   8306	    340	   1984	  10630	   2986	drivers/tty/serial/pmac_zilog.o

   3808	    456	      0	   4264	   10a8	drivers/tty/serial/pxa.o
   4000	    264	      0	   4264	   10a8	drivers/tty/serial/pxa.o

  21781	   3864	      0	  25645	   642d	drivers/tty/serial/serial-tegra.o
  22037	   3608	      0	  25645	   642d	drivers/tty/serial/serial-tegra.o

   2481	    456	     96	   3033	    bd9	drivers/tty/serial/sprd_serial.o
   2673	    272	     96	   3041	    be1	drivers/tty/serial/sprd_serial.o

   5534	    300	    512	   6346	   18ca	drivers/tty/serial/vr41xx_siu.o
   5630	    204	    512	   6346	   18ca	drivers/tty/serial/vr41xx_siu.o

   6730	   1576	    128	   8434	   20f2	drivers/tty/serial/vt8500_serial.o
   6986	   1320	    128	   8434	   20f2	drivers/tty/serial/vt8500_serial.o

Cross compiled for mips architecture.

   3005	    488	      0	   3493	    da5	drivers/tty/serial/pnx8xxx_uart.o
   3189	    304	      0	   3493	    da5	drivers/tty/serial/pnx8xxx_uart.o

   4272	    196	   1056	   5524	   1594	drivers/tty/serial/dz.o
   4368	    100	   1056	   5524	   1594	drivers/tty/serial/dz.o

   6551	    144	     16	   6711	   1a37	drivers/tty/serial/ip22zilog.o
   6647	     48	     16	   6711	   1a37	drivers/tty/serial/ip22zilog.o

   9612	    428	   1520	  11560	   2d28	drivers/tty/serial/serial_txx9.o
   9708	    332	   1520	  11560	   2d28	drivers/tty/serial/serial_txx9.o

   4156	    296	     16	   4468	   1174	drivers/tty/serial/ar933x_uart.o
   4252	    200	     16	   4468	   1174	drivers/tty/serial/ar933x_uart.o

Cross compiled for arm archiecture.

  11716	   1780	     44	  13540	   34e4	drivers/tty/serial/sirfsoc_uart.o
  11808	   1688	     44	  13540	   34e4	drivers/tty/serial/sirfsoc_uart.o

  13352	    596	     56	  14004	   36b4	drivers/tty/serial/amba-pl011.o
  13444	    504	     56	  14004	   36b4	drivers/tty/serial/amba-pl011.o

Cross compiled for sparc architecture.

   4664	    528	     32	   5224	   1468	drivers/tty/serial/sunhv.o
   4848	    344	     32	   5224	   1468	drivers/tty/serial/sunhv.o

   8080	    332	     28	   8440	   20f8	drivers/tty/serial/sunzilog.o
   8184	    228	     28	   8440	   20f8	drivers/tty/serial/sunzilog.o

Cross compiled for ia64 architecture.

  10226	    549	    472	  11247	   2bef	drivers/tty/serial/sn_console.o
  10414	    365	    472	  11251	   2bf3	drivers/tty/serial/sn_console.o

The files drivers/tty/serial/zs.o, drivers/tty/serial/lpc32xx_hs.o and
drivers/tty/serial/lantiq.o did not compile.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The impact of the persistent scrollback feature on the code size is
rather small, so the config option is removed. The feature stays
disabled by default and can be enabled by using the boot command line
parameter 'vgacon.scrollback_persistent=1' or by setting
VGACON_SOFT_SCROLLBACK_PERSISTENT_ENABLE_BY_DEFAULT=y.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a scrollback buffers for each VGA console. The benefit is that
the scrollback history is not flushed when switching between consoles
but is persistent.
The buffers are allocated on demand when a new console is opened.

This breaks tools like clear_console that rely on flushing the
scrollback history by switching back and forth between consoles
which is why this feature is disabled by default.
Use the escape sequence \e[3J instead for flushing the buffer.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Reviewed-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This new callback is in preparation for persistent scrollback buffer
support for VGA consoles.
With a single scrollback buffer for all consoles, we could flush the
buffer just by invocating consw->con_switch(). But when each VGA console
has its own scrollback buffer, we need a new callback to tell the
video console driver which buffer to flush.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Reviewed-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This refactoring is in preparation for persistent scrollback
support for VGA console.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Reviewed-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:

omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?

Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().

Fixes: 61929cf0 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently this warning is triggered for allmodconfig on m68k.  It is
well intentioned, in that if you are building the driver but not
enabling one of the platforms where the hardware exists, you get a
warning.

The warning dates back to pre-git days, and now we have COMPILE_TEST
so we can use that to mask the warning for people who are obviously
just doing build coverage on tree wide changes.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds xilinx uart loopback support by modifying the
cdns_uart_set_mctrl function to handle the switch to loopback mode.
After this patch, the loopback mode can be enabled/disabled by
setting/clearing the TIOCM_LOOP modem bit via TIOCMBIS/TIOCMBIC
ioctls respectively.
Signed-off-by: Yasir-Khan <yasir_khan@mentor.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

8250 UART DMA support was marked broken by default as it was not
possible to pause ongoing RX DMA transfer. Now that both SDMA and
EDMA can support pause operation for RX DMA transactions, don't set
rx_dma_broken to true by default. With this patch 8250_omap driver will
use DMA by default.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is possible that DMA transfer is already complete but, completion
handler is yet to be called, when dmaengine_pause() is called in case of
error condition(like break/rx timeout). This leads to dmaengine_pause()
API to return EINVAL (as descriptor is already NULL) causing
rx_dma_broken flag to be set and effectively disabling RX DMA.
Fix this by calling dmaengine_pause() only when transfer is in progress.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is needed to work with the client operations which uses const ptrs.

Really, the flags pointer could be const, too, but this would be a tree
wide fix.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_register_device is just a wrapper for tty_register_device_attr with
NULL passed for drvdata and attr_grp. So similarly make
tty_port_register_device a wrapper of tty_port_register_device_attr so that
additions don't have to be made in both functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Let us create tty objects entirely in kernel space. Untested proposal to
show why all the ideas around rewriting half the uart stack are not needed.

With this a kernel created non file backed tty object could be used to handle
data, and set terminal modes. Not all ldiscs can cope with this as N_TTY in
particular has to work back to the fs/tty layer.

The tty_port code is however otherwise clean of file handles as far as I can
tell as is the low level tty port write path used by the ldisc, the
configuration low level interfaces and most of the ldiscs.

Currently you don't have any exposure to see tty hangups because those are
built around the file layer. However a) it's a fixed port so you probably
don't care about that b) if you do we can add a callback and c) you almost
certainly don't want the userspace tear down/rebuild behaviour anyway.

This should however be sufficient if we wanted for example to enumerate all
the bluetooth bound fixed ports via ACPI and make them directly available.
It doesn't deal with the case of a user opening a port that's also kernel
opened and that would need some locking out (so it returned EBUSY if bound
to a kernel device of some kind). That needs resolving along with how you
"up" or "down" your new bluetooth device, or enumerate it while providing
the existing tty API to avoid regressions (and to debug).
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The vendor driver allows setting baud-rates higher than 115200 baud.
There is a check in the vendor driver which prevents using more than
115200 baud during startup, however it does not have such a check in
.set_termios.
Higher baud-rates are often used by the bluetooth modules embedded into
the SDIO wifi chips (Amlogic devices use brcmfmac based wifi chips quite
often, 2000000 baud seems to be a common value for the UART baud-rate in
Amlogic's "libbt").

I have tested this on a Meson GXL device with uart_A (to which the
bluetooth module is connected, where initialization times out with
115200 baud) and uart_AO (which I manually set to 2000000 baud  and then
connected with my USB UART adapter to that).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For in-kernel tty users, we need to be able to create and destroy
'struct tty' that are not associated with a file. The creation side is
fine, but tty_release() needs to be split into the file handle portion
and the struct tty portion. Introduce a new function, tty_release_struct,
to handle just the destroying of a struct tty.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Here, If ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DT earlycon for omap_serial driver. This boot console is included
with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y, CONFIG_SERIAL_OMAP=y, and
CONFIG_OF_EARLY_FLATTREE=y.

This boot console is enabled with the command line option "earlycon"
(without "=<name>...") when the DT 'stdout-path' property matches a
compatible uart.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Exactly as in a80c49db ("serial8250: Mark console as CON_ANYTIME"),
to enable printk() during CPU hot-plugging.

Actually most of the serial console drivers do not use per-cpu resources
and can be marked as CON_ANYTIME.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>