- 12 Feb, 2019 40 commits
-
-
Beomho Seo authored
[ Upstream commit 31e93364 ] Commit 391f93f2 ("serial: core: Rework hw-assited flow control support") has changed the way the autoCTS mode is handled. According to that change, serial drivers which enable H/W autoCTS mode must set UPSTAT_AUTOCTS to prevent the serial core from inadvertently disabling TX. This patch adds proper handling of UPSTAT_AUTOCTS flag. Signed-off-by:
Beomho Seo <beomho.seo@samsung.com> [mszyprow: rephrased commit message] Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Adrian Hunter authored
[ Upstream commit 0e6e7c2f ] Always check the wait condition before returning timeout. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Reviewed-by:
Zhoujie Wu <zjwu@marvell.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Adrian Hunter authored
[ Upstream commit ea6d0273 ] Always check the wait condition before returning timeout. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
-
Kai-Heng Feng authored
[ Upstream commit e03e303e ] We can use MEMSTICK_POWER_{ON,OFF} along with pm_runtime_{get,put} helpers to let memstick host support runtime pm. The rpm count may go down to zero before the memstick host powers on, so the host can be runtime suspended. So before doing card detection, increment the rpm count to avoid the host gets runtime suspended. Balance the rpm count after card detection is done. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by:
-
Michal Suchanek authored
[ Upstream commit f6000a4e ] The bcm2835 mmc host tends to lock up for unknown reason so reset it on timeout. The upper mmc block layer tries retransimitting with single blocks which tends to work out after a long wait. This is better than giving up and leaving the machine broken for no obvious reason. Fixes: 660fc733 ("mmc: bcm2835: Add new driver for the sdhost controller.") Signed-off-by:
Michal Suchanek <msuchanek@suse.de> Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Eric Anholt <eric@anholt.net> Signed-off-by:
-
Phil Elwell authored
[ Upstream commit 07d40576 ] If the user issues an "mmc extcsd read", the SD controller receives what it thinks is a SEND_IF_COND command with an unexpected data block. The resulting operations leave the FSM stuck in READWAIT, a state which persists until the MMC framework resets the controller, by which point the root filesystem is likely to have been unmounted. A less heavyweight solution is to detect the condition and nudge the FSM by asserting the (self-clearing) FORCE_DATA_MODE bit. Link: https://github.com/raspberrypi/linux/issues/2728Signed-off-by:
Phil Elwell <phil@raspberrypi.org> Signed-off-by:
-
Suraj Jitindar Singh authored
[ Upstream commit 693ac10a ] The kvm capability KVM_CAP_SPAPR_TCE_VFIO is used to indicate the availability of in kernel tce acceleration for vfio. However it is currently the case that this is only available on a powernv machine, not for a pseries machine. Thus make this capability dependent on having the cpu feature CPU_FTR_HVMODE. [paulus@ozlabs.org - fixed compilation for Book E.] Signed-off-by:
Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Fabio Estevam authored
[ Upstream commit add68836 ] eukrea-tlv320.c machine driver runs on non-DT platforms and include <asm/mach-types.h> header file in order to be able to use some machine_is_eukrea_xxx() macros. Building it for ARM64 causes the following build error: sound/soc/fsl/eukrea-tlv320.c:28:10: fatal error: asm/mach-types.h: No such file or directory Avoid this error by not allowing to build the SND_SOC_EUKREA_TLV320 driver when ARM64 is selected. This is needed in preparation for the i.MX8M support. Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Fabio Estevam <festevam@gmail.com> Acked-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 88af3209 ] WARNING: vmlinux.o(.text+0x19f90): Section mismatch in reference from the function littleton_init_lcd() to the function .init.text:pxa_set_fb_info() The function littleton_init_lcd() references the function __init pxa_set_fb_info(). This is often because littleton_init_lcd lacks a __init annotation or the annotation of pxa_set_fb_info is wrong. WARNING: vmlinux.o(.text+0xf824): Section mismatch in reference from the function zeus_register_ohci() to the function .init.text:pxa_set_ohci_info() The function zeus_register_ohci() references the function __init pxa_set_ohci_info(). This is often because zeus_register_ohci lacks a __init annotation or the annotation of pxa_set_ohci_info is wrong. WARNING: vmlinux.o(.text+0xf95c): Section mismatch in reference from the function cm_x300_init_u2d() to the function .init.text:pxa3xx_set_u2d_info() The function cm_x300_init_u2d() references the function __init pxa3xx_set_u2d_info(). This is often because cm_x300_init_u2d lacks a __init annotation or the annotation of pxa3xx_set_u2d_info is wrong. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Stanislav Fomichev authored
[ Upstream commit a0517a0f ] For some reason, my older GCC (< 4.8) isn't smart enough to optimize the !__builtin_constant_p() branch in bpf_htons, I see: error: implicit declaration of function '__builtin_bswap16' Let's use __bpf_constant_htons as suggested by Daniel Borkmann. I tried to use simple htons, but it produces the following: test_progs.c:54:17: error: braced-group within expression allowed only inside a function .eth.h_proto = htons(ETH_P_IP), Signed-off-by:
Stanislav Fomichev <sdf@google.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Joey Zhang authored
[ Upstream commit e4a7dca5 ] In the ioctl_event_ctl() SWITCHTEC_IOCTL_EVENT_IDX_ALL case, we call event_ctl() several times with the same "ctl" struct. Each call clobbers ctl.flags, which leads to the problem that we may not actually enable or disable all events as the user requested. Preserve the event flag value with a temporary variable. Fixes: 52eabba5 ("switchtec: Add IOCTLs to the Switchtec driver") Signed-off-by:
Joey Zhang <joey.zhang@microchip.com> Signed-off-by:
Wesley Sheng <wesley.sheng@microchip.com> [bhelgaas: changelog] Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Logan Gunthorpe <logang@deltatee.com> Signed-off-by:
-
Jan Kara authored
[ Upstream commit d288d958 ] When inode is corrupted so that extent type is invalid, some functions (such as udf_truncate_extents()) will just BUG. Check that extent type is valid when loading the inode to memory. Reported-by:
Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Icenowy Zheng authored
[ Upstream commit 2659392e ] The new Allwinner H6 SoC's USB2 PHY has two holes -- USB1 (which is a 3.0 port with dedicated PHY) and USB2 (which doesn't exist at all). Add support for this kind of missing USB PHY index. Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Reviewed-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
[ Upstream commit 4f5c85fe ] It was observed that when using seqentional mode contrary to the documentation, the SS bit (which is supposed to only be set if automatic/sequence command completed normally), is sometimes set together with NA (NAK in address phase) causing transfer to falsely be considered successful. My assumption is that this does not happen during manual mode since the controller is stopping its work the moment it sets NA/ND bit in status register. This is not the case in Automatic/Sequentional mode where it is still working to send STOP condition and the actual status we get depends on the time when the ISR is run. This patch changes the order of checking status bits in ISR - error conditions are checked first and only if none of them occurred, the transfer may be considered successful. This is required to introduce using of sequentional mode in next patch. Signed-off-by:
Krzysztof Adamski <krzysztof.adamski@nokia.com> Reviewed-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Viresh Kumar authored
[ Upstream commit 90e3577b ] The value of opp_table->regulator_count is not very consistent right now and it may end up being 0 while we do have a "opp-microvolt" property in the OPP table. It was kept that way as we used to check if any regulators are set with the OPP core for a device or not using value of regulator_count. Lets use opp_table->regulators for that purpose as the meaning of regulator_count is going to change in the later patches. Reported-by:
Quentin Perret <quentin.perret@arm.com> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Yangtao Li authored
[ Upstream commit 9456823c ] of_find_node_by_path() acquires a reference to the node returned by it and that reference needs to be dropped by its caller. bl_idle_init() doesn't do that, so fix it. Signed-off-by:
Yangtao Li <tiny.windzz@gmail.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Anson Huang authored
[ Upstream commit 0efcc2c0 ] Same as other i.MX6 SoCs, ensure unused MMDC channel's handshake is bypassed, this is to make sure no request signal will be generated when periphe_clk_sel is changed or SRC warm reset is triggered. Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 9f83cfdb ] The driver overrides the error codes returned by platform_get_irq() to -EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe permanently instead of the deferred probing. Switch to propagating the error code upstream, still checking/overriding IRQ0 as libata regards it as "no IRQ" (thus polling) anyway... Fixes: 9ec36caf ("of/irq: do irq resolution in platform_get_irq") Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Will Deacon authored
[ Upstream commit a868e853 ] After removing an entry from a queue (e.g. reading an event in arm_smmu_evtq_thread()) it is necessary to advance the MMIO consumer pointer to free the queue slot back to the SMMU. A memory barrier is required here so that all reads targetting the queue entry have completed before the consumer pointer is updated. The implementation of queue_inc_cons() relies on a writel() to complete the previous reads, but this is incorrect because writel() is only guaranteed to complete prior writes. This patch replaces the call to writel() with an mb(); writel_relaxed() sequence, which gives us the read->write ordering which we require. Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Vivek Gautam authored
[ Upstream commit 89cddc56 ] qcom,smmu-v2 is an arm,smmu-v2 implementation with specific clock and power requirements. On msm8996, multiple cores, viz. mdss, video, etc. use this smmu. On sdm845, this smmu is used with gpu. Add bindings for the same. Signed-off-by:
Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Tomasz Figa <tfiga@chromium.org> Tested-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
-
Tejas Joglekar authored
[ Upstream commit 244add8e ] In stream mode, when fast-forwarding TRBs, the stream number is not cleared causing the new stream to not get assigned. So we don't want controller to carry on transfers when short packet is received. So disable the CSP for stream capable endpoint. This is based on the 3.30a Programming guide, where table 3-1 device descriptor structure field definitions says for CSP bit If this bit is 0, the controller generates an XferComplete event and remove the stream. So if we keep CSP as 1 then switching between streams would not happen as in stream mode, when fast-forwarding TRBs, the stream number is not cleared causing the new stream to not get assigned. Signed-off-by:
Tejas Joglekar <joglekar@synopsys.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Wolfram Sang authored
[ Upstream commit e990e127 ] The datasheet says we must stop the timer before changing the clock divider. This can happen when the restart handler is called while the watchdog is running. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by:
Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by:
-
Linus Walleij authored
[ Upstream commit 738a05e6 ] The vendor firmware was analyzed to get the right idea about this flash layout. /proc/mtd contains: dev: size erasesize name mtd0: 01e7ff40 00020000 "rootfs" mtd1: 01f40000 00020000 "upgrade" mtd2: 00040000 00020000 "rgdb" mtd3: 00020000 00020000 "nvram" mtd4: 00040000 00020000 "RedBoot" mtd5: 00020000 00020000 "LangPack" mtd6: 02000000 00020000 "flash" Here "flash" is obviously the whole device and we know "rootfs" is a bogus hack to point to a squashfs rootfs inside of the main "upgrade partition". We know "RedBoot" is the first 0x40000 of the flash and the "upgrade" partition follows from 0x40000 to 0x1f8000. So we have mtd0, 1, 4 and 6 covered. Remains: mtd2: 00040000 00020000 "rgdb" mtd3: 00020000 00020000 "nvram" mtd5: 00020000 00020000 "LangPack" Inspecting the flash at 0x1f8000 and 0x1fa000 reveals each of these starting with "RGCFG1" so we assume 0x1f8000-1fbfff is "rgdb" of 0x40000. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Philipp Zabel authored
[ Upstream commit 75fa6e4f ] Add support for the third loop filter mode V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_DISABLED_AT_SLICE_BOUNDARY, and fix V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA and V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA controls. The filter offset controls are signed values in the -6 to 6 range and are stored into the slice header fields slice_alpha_c0_offset_div2 and slice_beta_offset_div2. The actual filter offsets FilterOffsetA/B are double their value, in range of -12 to 12. Rename variables to more closely match the nomenclature in the H.264 specification. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Jiong Wang authored
[ Upstream commit 17f6c83f ] For micro-mips, srlv inside POOL32A encoding space should use 0x50 sub-opcode, NOT 0x90. Some early version ISA doc describes the encoding as 0x90 for both srlv and srav, this looks to me was a typo. I checked Binutils libopcode implementation which is using 0x50 for srlv and 0x90 for srav. v1->v2: - Keep mm_srlv32_op sorted by value. Fixes: f31318fd ("MIPS: uasm: Add srlv uasm instruction") Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Acked-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
Jiong Wang <jiong.wang@netronome.com> Signed-off-by:
-
Russell King - ARM Linux authored
[ Upstream commit 84fb6c7f ] It was noticed that unbinding and rebinding the KSZ8851 ethernet resulted in the driver reporting "failed to read device ID" at probe. Probing the reset line with a 'scope while repeatedly attempting to bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is constantly held at zero, meaning the device is held in reset, and does not respond on the SPI bus. Experimentation with the startup delay on the regulator set to 50ms shows that the reset is positively released after 20ms. Schematics for this board are not available, and the traces are buried in the inner layers of the board which makes tracing where the RSTN pin extremely difficult. We can only guess that the RSTN pin is wired to a reset generator chip driven off the ethernet supply, which fits the observed behaviour. Include this delay in the regulator startup delay - effectively treating the reset as a "supply stable" indicator. This can not be modelled as a delay in the KSZ8851 driver since the reset generation is board specific - if the RSTN pin had been wired to a GPIO, reset could be released earlier via the already provided support in the KSZ8851 driver. This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based on Blaze schematics that should be very close to SDP4430: TPS22902YFPR is used as the regulator switch (gpio48 controlled): Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV. (SCH Note: Threshold set at 90%. Vsense: 0.405V). According to the TPS3808 data sheet the RESET delay time when Ct is open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> [tony@atomide.com: updated with notes from schematics from Peter] Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Yu Zhao authored
[ Upstream commit c12b08eb ] The parameter is still there but it's ignored. We need to check its value before deciding to go into passthrough mode for AMD IOMMU v2 capable device. We occasionally use this parameter to force v2 capable device into translation mode to debug memory corruption that we suspect is caused by DMA writes. To address the following comment from Joerg Roedel on the first version, v2 capability of device is completely ignored. > This breaks the iommu_v2 use-case, as it needs a direct mapping for the > devices that support it. And from Documentation/admin-guide/kernel-parameters.txt: This option does not override iommu=pt Fixes: aafd8ba0 ("iommu/amd: Implement add_device and remove_device") Signed-off-by:
Yu Zhao <yuzhao@google.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit a9d9f6b8 ] devm_kstrdup() may return NULL if internal allocation failed. Thus using label, name is unsafe without checking. Therefor in the unlikely case of allocation failure, sx150x_probe() simply returns -ENOMEM. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Fixes: 9e80f906 ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver") Signed-off-by:
-
Andy Shevchenko authored
[ Upstream commit 54d48183 ] The missed break statement in the outer switch makes the code fall through always and thus always same value will be printed. Besides that, compiler warns about missed fall through marker: drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’: drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=] switch (pcm) { ^~~~~~ Add the missing break statement to work correctly without compilation warnings. Fixes: fa8d965d ("usb: dwc3: trace: pretty print high-bandwidth transfers too") Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Kaike Wan authored
[ Upstream commit ca95f802 ] Currently, When a reserved operation is completed, its entry in the send queue will not be unreserved, which leads to the miscalculation of qp->s_avail and thus the triggering of a WARN_ON call trace. This patch fixes the problem by unreserving the reserved operation when it is completed. Fixes: 856cc4c2 ("IB/hfi1: Add the capability for reserved operations") Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Kaike Wan <kaike.wan@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Peter Rajnoha authored
[ Upstream commit df44b479 ] Propagate error code back to userspace if writing the /sys/.../uevent file fails. Before, the write operation always returned with success, even if we failed to recognize the input string or if we failed to generate the uevent itself. With the error codes properly propagated back to userspace, we are able to react in userspace accordingly by not assuming and awaiting a uevent that is not delivered. Signed-off-by:
Peter Rajnoha <prajnoha@redhat.com> Signed-off-by:
-
Alexander Duyck authored
[ Upstream commit c37d721c ] Move the async_synchronize_full call out of __device_release_driver and into driver_detach. The idea behind this is that the async_synchronize_full call will only guarantee that any existing async operations are flushed. This doesn't do anything to guarantee that a hotplug event that may occur while we are doing the release of the driver will not be asynchronously scheduled. By moving this into the driver_detach path we can avoid potential deadlocks as we aren't holding the device lock at this point and we should not have the driver we want to flush loaded so the flush will take care of any asynchronous events the driver we are detaching might have scheduled. Fixes: 765230b5 ("driver-core: add asynchronous probing support for drivers") Reviewed-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Reviewed-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
-
Chen-Yu Tsai authored
[ Upstream commit 6e6da203 ] All the audio interfaces on Allwinner SoCs need to change their module clocks during operation, to switch between support for 44.1 kHz and 48 kHz family sample rates. The clock rate for the module clocks is governed by their upstream audio PLL. The module clocks themselves only have a gate, and sometimes a divider or mux. Thus any rate changes need to be propagated upstream. Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve this. Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Chunfeng Yun authored
[ Upstream commit a0678e2e ] Fix the issue: device doesn't accept LGO_U1/U2: 1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2 by default; 2. enable/disable controller to initiate requests for transition into U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE; Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by:
-
Bart Van Assche authored
[ Upstream commit ce10a5b3 ] tk_core.seq is initialized open coded, but that misses to initialize the lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq consequently lack a name and are hard to read. Use the proper initializer which takes care of the lockdep map initialization. [ tglx: Massaged changelog ] Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: peterz@infradead.org Cc: tj@kernel.org Cc: johannes.berg@intel.com Link: https://lkml.kernel.org/r/20181128234325.110011-12-bvanassche@acm.orgSigned-off-by:
-
Mathias Nyman authored
[ Upstream commit e8610894 ] When initializing a hub we want to give a USB3 port in link training the same debounce delay time before autosuspening the hub as already trained, connected enabled ports. USB3 ports won't reach the enabled state with "current connect status" and "connect status change" bits set until the USB3 link training finishes. Catching the port in link training (polling) and adding the debounce delay prevents unnecessary failed attempts to autosuspend the hub. Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Anurag Kumar Vulisha authored
[ Upstream commit b7a4fbe2 ] Availability of TRB's is calculated using dwc3_calc_trbs_left(), which determines total available TRB's based on the HWO bit set in a TRB. In the present code, __dwc3_prepare_one_trb() is called with a TRB which needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit if the total available TRBs are zero. Since the present working TRB (which is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have the HWO bit set before calling dwc3_calc_trbs_left(), there are chances that dwc3_calc_trbs_left() wrongly calculates this present working TRB as free(since the HWO bit is not yet set) and returns the total available TRBs as greater than zero (including the present working TRB). This could be a problem. This patch corrects the above mentioned problem in __dwc3_prepare_one_trb() by increementing the dep->trb_enqueue at the last (after preparing the TRB) instead of increementing at the start and setting the IOC bit only if the total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are increementing the dep->trb_enqueue at the last, the present working TRB is also considered as available by dwc3_calc_trbs_left() and non zero value is returned . So, according to the modified logic, when the total available TRBs is equal to 1 that means the total available TRBs in the pool are 0. Signed-off-by:
Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com> Reviewed-by:
Thinh Nguyen <thinhn@synopsys.com> Tested-by:
Tejas Joglekar <tejas.joglekar@synopsys.com> Signed-off-by:
-
Zoran Markovic authored
[ Upstream commit 5b841bfa ] Function smack_key_permission() only issues smack requests for the following operations: - KEY_NEED_READ (issues MAY_READ) - KEY_NEED_WRITE (issues MAY_WRITE) - KEY_NEED_LINK (issues MAY_WRITE) - KEY_NEED_SETATTR (issues MAY_WRITE) A blank smack request is issued in all other cases, resulting in smack access being granted if there is any rule defined between subject and object, or denied with -EACCES otherwise. Request MAY_READ access for KEY_NEED_SEARCH and KEY_NEED_VIEW. Fix the logic in the unlikely case when both MAY_READ and MAY_WRITE are needed. Validate access permission field for valid contents. Signed-off-by:
Zoran Markovic <zmarkovic@sierrawireless.com> Signed-off-by:
Casey Schaufler <casey@schaufler-ca.com> Cc: Casey Schaufler <casey@schaufler-ca.com> Cc: James Morris <jmorris@namei.org> Cc: "Serge E. Hallyn" <serge@hallyn.com> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit aa35dc3c ] If vpbe_set_default_output() or vpbe_set_default_mode() fails, vpbe_initialize() returns error code without releasing resources. The patch adds error handling for that case. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Sebastian Andrzej Siewior authored
[ Upstream commit 6637401c ] Every user of user_insn() passes an user memory pointer to this macro. Add might_fault() to user_insn() so we can spot users which are using this macro in sections where page faulting is not allowed. [ bp: Space it out to make it more visible. ] Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Rik van Riel <riel@surriel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: "Jason A. Donenfeld" <Jason@zx2c4.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm ML <kvm@vger.kernel.org> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20181128222035.2996-6-bigeasy@linutronix.deSigned-off-by:
-
