With the spi device table udev can autoload the spi-mux module in
the presence of an spi-mux device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210721095321.2165453-1-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The bcm2835_spi_transfer_one function can create a deadlock
if it is called while another thread already has the
CCF lock.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Fixes: f8043872 ("spi: add driver for BCM2835")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210716210245.13240-2-alexandru.tachici@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8 ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.

Undo 734882a8 ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.

Fixes: 734882a8 ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

cadence-quadspi has a builtin Auto-HW polling funtionality using which
it keep tracks of completion of write operations. When Auto-HW polling
is enabled, it automatically initiates status register read operation,
until the flash clears its busy bit.

cadence-quadspi controller doesn't allow an address phase when
auto-polling the busy bit on the status register. Unlike SPI NOR
flashes, SPI NAND flashes do require the address of status register
when polling the busy bit using the read register operation. As
Auto-HW polling is enabled by default, cadence-quadspi returns a
timeout for every write operation after an indefinite amount of
polling on SPI NAND flashes.

Disable Auto-HW polling completely as the spi-nor core, spinand core,
etc. take care of polling the busy bit on their own.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210713125743.1540-2-a-nandan@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix below division by zero warning:
- The reason for dividing by zero is because the dummy bus width is zero,
  but if the dummy n bytes is zero, it indicates that there is no data transfer,
  so we can just return zero without doing any calculations.

[    0.795337] Division by zero in kernel.
   :
[    0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[    0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)

Fixes: 7512eaf5 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/92eea403-9b21-2488-9cc1-664bee760c5e@nskint.co.jpSigned-off-by: Mark Brown <broonie@kernel.org>

Revert to change to a better code.

This reverts commit 55cef88b.
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Link: https://lore.kernel.org/r/bd30bdb4-07c4-f713-5648-01c898d51f1b@nskint.co.jpSigned-off-by: Mark Brown <broonie@kernel.org>

Fix below division by zero warning:
- Added an if statement because buswidth can be zero, resulting in division by zero.
- The modified code was based on another driver (atmel-quadspi).

[    0.795337] Division by zero in kernel.
   :
[    0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[    0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)

Fixes: 7512eaf5 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Link: https://lore.kernel.org/r/ed989af6-da88-4e0b-9ed8-126db6cad2e4@nskint.co.jpSigned-off-by: Mark Brown <broonie@kernel.org>

This patch move devm_spi_register_master to the end of mtk_spi_probe.
If slaves call spi_sync in there probe function, master should have probe done.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210713114247.1536-1-mason.zhang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

In FIFO mode were two problems:
- RX mode was never handled and
- in this case the tx_buf pointer was NULL and caused an exception

fix this by handling RX mode in mtk_spi_fifo_transfer

Fixes: a568231f ("spi: mediatek: Add spi bus for Mediatek MT8173")
Signed-off-by: Peter Hess <peter.hess@ph-home.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210706121609.680534-1-linux@fw-web.deSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 5fa5e6de ("spi: atmel: Switch to transfer_one transfer
method") switched to using transfer_one and set_cs.  The
core doesn't call set_cs when the chip select lines are gpios.  Add the
SPI_MASTER_GPIO_SS flag to the driver to ensure the calls to set_cs
happen since the driver programs configuration registers there.

Fixes: 5fa5e6de ("spi: atmel: Switch to transfer_one transfer method")
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210629192218.32125-1-dan.sneddon@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add pm_runtime calls in probe/probe error path and remove
in order to be consistent in all places in ordering and
ensure that pm_runtime is disabled prior to resources used
by the SPI controller.

This patch also fixes the 2 following warnings on driver remove:
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:594 clk_core_disable_lock+0x18/0x24
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:476 clk_unprepare+0x24/0x2c

Fixes: 038ac869 ("spi: stm32: add runtime PM support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-2-git-send-email-alain.volmat@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since 00b80ac9 ("spi: imx: mx51-ecspi: Move some initialisation to
prepare_message hook."), the MX51_ECSPI_CONFIG write no longer happens
in prepare_transfer hook, but rather in prepare_message hook, however
the MX51_ECSPI_CONFIG delay is still left in prepare_transfer hook and
thus has no effect. This leads to low bus frequency operation problems
described in 6fd8b850 ("spi: spi-imx: Fix out-of-order CS/SCLK
operation at low speeds") again.

Move the MX51_ECSPI_CONFIG write delay into the prepare_message hook
as well, thus reinstating the low bus frequency fix.

Fixes: 00b80ac9 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210703022300.296114-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

In case of Full-Duplex mode, DXP flag is set when RXP and TXP flags are
set. But to avoid 2 different handlings, just add TXP and RXP flag in
the mask instead of DXP, and then keep the initial handling of TXP and
RXP events.
Also rephrase comment about EOTIE which is one of the interrupt enable
bits. It is not triggered by any event.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/1625042723-661-3-git-send-email-alain.volmat@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some controllers like qcom geni need the parent device to be used for
dma mapping, so add a dma_map_dev field and let drivers fill this to be
used as mapping device
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210625052213.32260-4-vkoul@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert spi for Xilinx Zynq UltraScale+ MPSoC GQSPI bindings
documentation to YAML.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210613214317.296667-1-iwamatsu@nigauri.orgSigned-off-by: Mark Brown <broonie@kernel.org>

There is an assignment of ancillary->mode to itself which looks
dubious since the proceeding comment states that the speed and
mode is taken over from the SPI main device, indicating that
ancillary->mode should assigned using the value spi->mode.
Fix this.

Addresses-Coverity: ("Self assignment")
Fixes: 0c79378c ("spi: add ancillary device support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210623172300.161484-1-colin.king@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Changes in v10:
- The internal CS inactive function is only supported after VER 0x00110002

Changes in v9:
- Conver to use CS GPIO description

Changes in v8:
- There is a problem with the version 7 mail format. resend it

Changes in v7:
- Fall back "rockchip,rv1126-spi" to "rockchip,rk3066-spi"

Changes in v6:
- Consider to compatibility, the "rockchip,rk3568-spi" is removed in
  Series-changes v5, so the commit massage should also remove the
  corresponding information

Changes in v5:
- Change to leave one compatible id rv1126, and rk3568 is compatible
  with rv1126

Changes in v4:
- Adjust the order patches
- Simply commit massage like redundancy "application" content

Changes in v3:
- Fix compile error which is find by Sascha in [v2,2/8]

Jon Lin (6):
  dt-bindings: spi: spi-rockchip: add description for rv1126
  spi: rockchip: add compatible string for rv1126
  spi: rockchip: Set rx_fifo interrupt waterline base on transfer item
  spi: rockchip: Wait for STB status in slave mode tx_xfer
  spi: rockchip: Support cs-gpio
  spi: rockchip: Support SPI_CS_HIGH

 .../devicetree/bindings/spi/spi-rockchip.yaml |  1 +
 drivers/spi/spi-rockchip.c                    | 55 ++++++++++++++-----
 2 files changed, 41 insertions(+), 15 deletions(-)

--
2.17.1

dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095843.3228-3-wsa+renesas@sang-engineering.comSigned-off-by: Mark Brown <broonie@kernel.org>

dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095843.3228-2-wsa+renesas@sang-engineering.comSigned-off-by: Mark Brown <broonie@kernel.org>

The description below will be used for rv1126.dtsi or compatible one in
the future
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-2-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

1.Add standard spi-cs-high support
2.Refer to spi-controller.yaml for details
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104848.19539-2-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

1.Add standard cs-gpio support
2.Refer to spi-controller.yaml for details
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104848.19539-1-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

After ROCKCHIP_SPI_VER2_TYPE2, SR->STB is a more accurate judgment
bit for spi slave transmition.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-5-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

The error here is to calculate the width as 8 bits. In fact, 16 bits
should be considered.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-4-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add compatible string for rv1126 for potential applications.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-3-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add binding support for devices, that have more than one
chip select. A typical example are SPI connected microcontroller,
that can also be programmed over SPI like NXP Kinetis or
chips with a configuration and a data chip select, such as
Microchip's MRF89XA transceiver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-3-sebastian.reichel@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Introduce support for ancillary devices, similar to existing
implementation for I2C. This is useful for devices having
multiple chip-selects, for example some microcontrollers
provide a normal SPI interface and a flashing SPI interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-2-sebastian.reichel@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert SPI for Xilinx bindings documentation to YAML schemas.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210605002931.858031-1-iwamatsu@nigauri.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert spi for Cadence SPI bindings documentation to YAML.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210605003811.858676-1-iwamatsu@nigauri.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Remove struct stm32_qspi_flash's field qspi which is not used.

Fixes: c530cd1d ("spi: spi-mem: add stm32 qspi controller")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210615090115.30702-1-patrice.chotard@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add OF support as already done for ACPI to take driver
MODULE_DEVICE_TABLE(of, ..) into account.

For example with this change a spi nor device MODALIAS changes from:

MODALIAS=spi:spi-nor

to

MODALIAS=of:Nspi-flashT(null)Cjedec,spi-nor
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210525091003.18228-1-m.felsch@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

when meson_spicc_clk_init returns failed, it should goto the
out_clk label.
Signed-off-by: zpershuai <zpershuai@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1623562156-21995-1-git-send-email-zpershuai@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

In meson_spifc_probe function, when enable the device pclk clock is
error, it should use clk_disable_unprepare to release the core clock.
Signed-off-by: zpershuai <zpershuai@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1623562172-22056-1-git-send-email-zpershuai@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix the following make W=1 warning:

  drivers/spi/spi-mem.c:819: warning: expecting prototype for spi_mem_driver_unregister_with_owner(). Prototype was for spi_mem_driver_unregister() instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210601120721.3198488-1-yangyingliang@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

No one seems to be using this global and exported function, so remove it
as it is no longer needed.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210609071918.2852069-1-gregkh@linuxfoundation.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This patch uses debugfs_regset32 interface to create the registers dump
file. Use it instead of creating a generic debugfs file with manually
written read callback function.

With these entries, users can check all the SPI controller registers
during run time.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1622789718-13977-1-git-send-email-f.fangjian@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix the following compilation warning using W=1 build:
arm-linux-gnueabi-ld: drivers/spi/spi-stm32-qspi.o: in function `stm32_qspi_poll_status':
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210604075009.25914-1-patrice.chotard@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Patrice Chotard <patrice.chotard@foss.st.com>:

From: Patrice Chotard <patrice.chotard@foss.st.com>

This series adds support for the spi_mem_poll_status() spinand
interface.
Some QSPI controllers allows to poll automatically memory
status during operations (erase, read or write). This allows to
offload the CPU for this task.
STM32 QSPI is supporting this feature, driver update are also
part of this series.

Changes in v5:
  - Update spi_mem_read_status() description.
  - Update poll_status() description API by indicating that data buffer is
    filled with last status value.
  - Update timeout parameter by timeout_ms in spi_mem_poll_status() prototype.
  - Remove parenthesys arount -EINVAL in spi_mem_poll_status().
  - Add missing spi_mem_supports_op() call in stm32_qspi_poll_status().
  - Add Boris Reviewed-by for patch 1 and 2.

Changes in v4:
  - Remove init_completion() from spi_mem_probe() added in v2.
  - Add missing static for spi_mem_read_status().
  - Check if operation in spi_mem_poll_status() is a READ.
  - Update patch 2 commit message.
  - Add comment which explains how delays has been calculated.
  - Rename SPINAND_STATUS_TIMEOUT_MS to SPINAND_WAITRDY_TIMEOUT_MS.

Chnages in v3:
  - Add spi_mem_read_status() which allows to read 8 or 16 bits status.
  - Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status().
    and also to poll_status() callback.
  - Move spi_mem_supports_op() in SW-based polling case.
  - Add delay before invoquing read_poll_timeout().
  - Remove the reinit/wait_for_completion() added in v2.
  - Add initial_delay_us and polling_delay_us parameters to spinand_wait().
  - Add SPINAND_READ/WRITE/ERASE/RESET_INITIAL_DELAY_US and
    SPINAND_READ/WRITE/ERASE/RESET_POLL_DELAY_US defines.
  - Remove spi_mem_finalize_op() API added in v2.

Changes in v2:
  - Indicates the spi_mem_poll_status() timeout unit
  - Use 2-byte wide status register
  - Add spi_mem_supports_op() call in spi_mem_poll_status()
  - Add completion management in spi_mem_poll_status()
  - Add offload/non-offload case management in spi_mem_poll_status()
  - Optimize the non-offload case by using read_poll_timeout()
  - mask and match stm32_qspi_poll_status()'s parameters are 2-byte wide
  - Make usage of new spi_mem_finalize_op() API in
    stm32_qspi_wait_poll_status()

Patrice Chotard (3):
  spi: spi-mem: add automatic poll status functions
  mtd: spinand: use the spi-mem poll status APIs
  spi: stm32-qspi: add automatic poll status feature

 drivers/mtd/nand/spi/core.c  | 45 +++++++++++++------
 drivers/spi/spi-mem.c        | 86 ++++++++++++++++++++++++++++++++++++
 drivers/spi/spi-stm32-qspi.c | 86 ++++++++++++++++++++++++++++++++----
 include/linux/mtd/spinand.h  | 22 +++++++++
 include/linux/spi/spi-mem.h  | 16 +++++++
 5 files changed, 234 insertions(+), 21 deletions(-)

base-commit: 6efb943b

--
2.17.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

The current implementation of the driver holds a spin lock for the
duration of the transfer, releasing it only to enable interrupts for
short periods of time.  As this would prevent any interrupt from
happening, this could cause system performance issues every time a SPI
message is sent.  Since the spi core now handles message syncronization
we can reduce the amount of time the spin-lock is held to the regions
where both the calling thread and the interrupt might interract.
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210602160816.4890-2-dan.sneddon@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Switch from using our own transfer_one_message routine to using the one
provided by the SPI core.
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210602160816.4890-1-dan.sneddon@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>