This way this device can be used with irtty-sir -
at least on Toshiba Satellite A20-S103 it is not configured by default
and needs PNP activation before it starts to respond on I/O ports.

This device has actually its own driver (ali-ircc),
but this driver seems to be non-functional for a very long time
(see http://permalink.gmane.org/gmane.linux.irda.general/484
http://permalink.gmane.org/gmane.network.protocols.obex.openobex.user/943
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=535070 ).
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently mxs-auart doesn't care correctly about the baud rate divisor.
According to reference manual the baud rate divisor must be between
0x000000EC and 0x003FFFC0. So calculate the possible baud rate range
and use it for uart_get_baud_rate().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Whenever the UART device driver gets closed from userland, the driver
disables the UART unit and then stops the clocks to save power.

The bit which disabled the UART unit is described as:

 "UART Enable. If this bit is set to 1, the UART is enabled. Data
  transmission and reception occurs for the UART signals. When the
  UART is disabled in the middle of transmission or reception, it
  completes the current character before stopping."

The important part is the "it completes the current character". Whenever
a reception is ongoing when the UART gets disabled (including the clock
off) the statemachine freezes and "remembers" this state on the next
open() when re-enabling the unit's clock.

In this case we end up receiving an additional bogus character
immediately.

The solution in this change is to switch the AUART unit into its reset
state on close() and only release it from its reset state on the next
open().

Note: when the unit is also used as system console it is always 'in use',
so we cannot reset it on close().
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This function clears the reset the AUART unit is in after system start
to make it work.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512

We had add RS232/485 RTS control with fecf27a3. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).

This patch will modify 2 sections.

One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.

The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

devtype structures are all declared as const.
Compiler does not complain because we cast
their pointers to save them in .driver_data.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We currently register the uart driver during device probe
which makes it hard to support more than one chip.
Move the driver registration to module init/exit time and
preallocate space for up to 8 lines (4-8 chips).
Reported-by: Michael Allwright <michael.allwright@upb.de>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation of supporting multiple devices we should save
the per-chip line number (0 or 1), because the uart_port line
will reflect system-wide uart number and will be offseted for
chips other than the first to register.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Support ZTE uart with some registers differing offset.
Probe as platform device for not AMBA IP ID is
available on ZTE uart.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Improve LCRH register access decision as ARM PL011 lcrh
register serve as both TX and RX, while other SOC may
implement TX and RX function with separated register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce register look up table as different SOC venders
may have different register offset for the some register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce register accessor to ease loop up table access
in later patch.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename regs with enumeration to generalize register names.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.

The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.

Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.

Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).

Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.

NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uart_close() runs in non-atomic context only; use
spin_lock/unlock_irq instead of saving the interrupt state (which
== on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add "ti,dra742-uart" to the compatible list so the driver
workaround for UART module disable errata is enabled.

This does not break backward compatibility as existing DTBs
should continue to work with newer kernels albeit without the
capability to idle the UART module when DMA is used.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes I/O accesses on the Receiver Holding Register and on the
Transmitter Holding Register. Indeed AVR32 can only perform 32bit I/O
accesses on registers: using 8bit I/O accesses would read or write garbage
data.

Fixes: commit b5199d46 ("tty/serial: at91: add support to FIFOs")
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.

There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.

This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.

Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implementing enable_ms is optional by serial_core.
check_modem_status is just an empty local function.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When system goes into low power states like SUSPEND_MEM and
HIBERNATION, the hardware IP block may be powered off to reduce
the power consumption. This power down may cause problems on
some imx platforms, because the hardware settings are reset to
its power on default values which may differ from the ones when
it power off. This patch added the dev_pm_ops and implemented
two callbacks: suspend_noirq and resume_noirq, which will save
the necessory hardware parameters right before power down and
recover them before system uses the hardware.

Because added the dev_pm_ops, the old suspend/resume callbacks
under platform_driver will not be called any more. Changed their
prototypes and moved those two callbacks into dev_pm_ops too.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If serial8250_register_8250_port() fails, disable and unprepare the
clock before exiting.

Fixes: 1a8d2903 ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add RS485 control for Fintek F81504/508/512

F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.

When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.

When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.

When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.

We will force 0x01 on pci_fintek_setup().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Avoid usb reset crashes by making tty_io cdevs truly dynamic
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
Reported-by: Duncan Mackintosh <DMackintosh@cbnl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit e95044ba.

Commit e95044ba ("tty: serial: imx.c: Reset UART before activating
interrupts") terribly messes up with the console on mx6 boards, so
let's revert it.
Reported-by: kernelci.org bot <bot@kernelci.org>
Cc: David Jander <david@protonic.nl>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Other serial driver work wants to build on patches now in 4.2-rc4 so
merge the branch so this can properly happen.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull perf fix from Thomas Gleixner:
 "A single fix for the intel cqm perf facility to prevent IPIs from
  interrupt context"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/cqm: Return cached counter value from IRQ context

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - the manual revert of the SYSCALL32 changes which caused a
     regression

   - a fix for the MPX vma handling

   - three fixes for the ioremap 'is ram' checks.

   - PAT warning fixes

   - a trivial fix for the size calculation of TLB tracepoints

   - handle old EFI structures gracefully

  This also contains a PAT fix from Jan plus a revert thereof.  Toshi
  explained why the code is correct"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/pat: Revert 'Adjust default caching mode translation tables'
  x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
  x86/mm: Fix newly introduced printk format warnings
  mm: Fix bugs in region_is_ram()
  x86/mm: Remove region_is_ram() call from ioremap
  x86/mm: Move warning from __ioremap_check_ram() to the call site
  x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
  x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
  x86/mm/pat: Adjust default caching mode translation tables
  x86/fpu: Disable dependent CPU features on "noxsave"
  x86/mpx: Do not set ->vm_ops on MPX VMAs
  x86/mm: Add parenthesis for TLB tracepoint size calculation
  efi: Handle memory error structures produced based on old versions of standard

Toshi explains:

"No, the default values need to be set to the fallback types,
 i.e. minimal supported mode.  For WC and WT, UC is the fallback type.

 When PAT is disabled, pat_init() does update the tables below to
 enable WT per the default BIOS setup.  However, when PAT is enabled,
 but CPU has PAT -errata, WT falls back to UC per the default values."

Revert: ca1fec58 'x86/mm/pat: Adjust default caching mode translation tables'
Requested-by: Toshi Kani <toshi.kani@hp.com>
Cc: Jan Beulich <jbeulich@suse.de>
Link: http://lkml.kernel.org/r/1437577776.3214.252.camel@hp.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Peter reported the following potential crash which I was able to
reproduce with his test program,

[  148.765788] ------------[ cut here ]------------
[  148.765796] WARNING: CPU: 34 PID: 2840 at kernel/smp.c:417 smp_call_function_many+0xb6/0x260()
[  148.765797] Modules linked in:
[  148.765800] CPU: 34 PID: 2840 Comm: perf Not tainted 4.2.0-rc1+ #4
[  148.765803]  ffffffff81cdc398 ffff88085f105950 ffffffff818bdfd5 0000000000000007
[  148.765805]  0000000000000000 ffff88085f105990 ffffffff810e413a 0000000000000000
[  148.765807]  ffffffff82301080 0000000000000022 ffffffff8107f640 ffffffff8107f640
[  148.765809] Call Trace:
[  148.765810]  <NMI>  [<ffffffff818bdfd5>] dump_stack+0x45/0x57
[  148.765818]  [<ffffffff810e413a>] warn_slowpath_common+0x8a/0xc0
[  148.765822]  [<ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[  148.765824]  [<ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[  148.765825]  [<ffffffff810e422a>] warn_slowpath_null+0x1a/0x20
[  148.765827]  [<ffffffff811613f6>] smp_call_function_many+0xb6/0x260
[  148.765829]  [<ffffffff8107f640>] ? intel_cqm_stable+0x60/0x60
[  148.765831]  [<ffffffff81161748>] on_each_cpu_mask+0x28/0x60
[  148.765832]  [<ffffffff8107f6ef>] intel_cqm_event_count+0x7f/0xe0
[  148.765836]  [<ffffffff811cdd35>] perf_output_read+0x2a5/0x400
[  148.765839]  [<ffffffff811d2e5a>] perf_output_sample+0x31a/0x590
[  148.765840]  [<ffffffff811d333d>] ? perf_prepare_sample+0x26d/0x380
[  148.765841]  [<ffffffff811d3497>] perf_event_output+0x47/0x60
[  148.765843]  [<ffffffff811d36c5>] __perf_event_overflow+0x215/0x240
[  148.765844]  [<ffffffff811d4124>] perf_event_overflow+0x14/0x20
[  148.765847]  [<ffffffff8107e7f4>] intel_pmu_handle_irq+0x1d4/0x440
[  148.765849]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765853]  [<ffffffff81219bad>] ? vunmap_page_range+0x19d/0x2f0
[  148.765854]  [<ffffffff81219d11>] ? unmap_kernel_range_noflush+0x11/0x20
[  148.765859]  [<ffffffff814ce6fe>] ? ghes_copy_tofrom_phys+0x11e/0x2a0
[  148.765863]  [<ffffffff8109e5db>] ? native_apic_msr_write+0x2b/0x30
[  148.765865]  [<ffffffff8109e44d>] ? x2apic_send_IPI_self+0x1d/0x20
[  148.765869]  [<ffffffff81065135>] ? arch_irq_work_raise+0x35/0x40
[  148.765872]  [<ffffffff811c8d86>] ? irq_work_queue+0x66/0x80
[  148.765875]  [<ffffffff81075306>] perf_event_nmi_handler+0x26/0x40
[  148.765877]  [<ffffffff81063ed9>] nmi_handle+0x79/0x100
[  148.765879]  [<ffffffff81064422>] default_do_nmi+0x42/0x100
[  148.765880]  [<ffffffff81064563>] do_nmi+0x83/0xb0
[  148.765884]  [<ffffffff818c7c0f>] end_repeat_nmi+0x1e/0x2e
[  148.765886]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765888]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765890]  [<ffffffff811d07a6>] ? __perf_event_task_sched_in+0x36/0xa0
[  148.765891]  <<EOE>>  [<ffffffff8110ab66>] finish_task_switch+0x156/0x210
[  148.765898]  [<ffffffff818c1671>] __schedule+0x341/0x920
[  148.765899]  [<ffffffff818c1c87>] schedule+0x37/0x80
[  148.765903]  [<ffffffff810ae1af>] ? do_page_fault+0x2f/0x80
[  148.765905]  [<ffffffff818c1f4a>] schedule_user+0x1a/0x50
[  148.765907]  [<ffffffff818c666c>] retint_careful+0x14/0x32
[  148.765908] ---[ end trace e33ff2be78e14901 ]---

The CQM task events are not safe to be called from within interrupt
context because they require performing an IPI to read the counter value
on all sockets. And performing IPIs from within IRQ context is a
"no-no".

Make do with the last read counter value currently event in
event->count when we're invoked in this context.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikas Shivappa <vikas.shivappa@intel.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Will Auld <will.auld@intel.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1437490509-15373-1-git-send-email-matt@codeblueprint.co.ukSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull USB fixes from Greg KH:
 "Here's a few USB and PHY fixes for 4.2-rc4.

  Nothing major, the shortlog has the full details.

  All of these have been in linux-next successfully"

* tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
  USB: OHCI: fix bad #define in ohci-tmio.c
  cdc-acm: Destroy acm_minors IDR on module exit
  usb-storage: Add ignore-device quirk for gm12u320 based usb mini projectors
  usb-storage: ignore ZTE MF 823 card reader in mode 0x1225
  USB: OHCI: Fix race between ED unlink and URB submission
  usb: core: lpm: set lpm_capable for root hub device
  xhci: do not report PLC when link is in internal resume state
  xhci: prevent bus_suspend if SS port resuming in phase 1
  xhci: report U3 when link is in resume state
  xhci: Calculate old endpoints correctly on device reset
  usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function
  xhci: Workaround to get D3 working in Intel xHCI
  xhci: call BIOS workaround to enable runtime suspend on Intel Braswell
  usb: dwc3: Reset the transfer resource index on SET_INTERFACE
  usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU
  usb: gadget: mv_udc_core: fix phy_regs I/O memory leak
  usb: ulpi: ulpi_init should be executed in subsys_initcall
  phy: berlin-usb: fix divider for BG2
  phy: berlin-usb: fix divider for BG2CD
  phy/pxa: add HAS_IOMEM dependency
  ...

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small serial and tty fixes for reported issues.

  All have been in linux-next successfully"

* tag 'tty-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: vt: Fix !TASK_RUNNING diagnostic warning from paste_selection()
  serial: core: Fix crashes while echoing when closing
  m32r: Add ioreadXX/iowriteXX big-endian mmio accessors
  Revert "serial: imx: initialized DMA w/o HW flow enabled"
  sc16is7xx: fix FIFO address of secondary UART
  sc16is7xx: fix Kconfig dependencies
  serial: etraxfs-uart: Fix release etraxfs_uart_ports
  tty/vt: Fix the memory leak in visual_init
  serial: amba-pl011: Fix devm_ioremap_resource return value check
  n_tty: signal and flush atomically

Pull staging driver fixes from Greg KH:
 "Here are a number of iio and staging driver fixes for reported issues
  for 4.2-rc4.

  All have been in linux-next for a while with no problems"

* tag 'staging-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
  iio:light:stk3310: make endianness independent of host
  iio:light:stk3310: move device register to end of probe
  iio: mma8452: use iio event type IIO_EV_TYPE_MAG
  iio: mcp320x: Fix NULL pointer dereference
  iio: adc: vf610: fix the adc register read fail issue
  iio: mlx96014: Replace offset sign
  iio: magnetometer: mmc35240: fix SET/RESET sequence
  iio: magnetometer: mmc35240: Fix SET/RESET mask
  iio: magnetometer: mmc35240: Fix crash in pm suspend
  iio:magnetometer:bmc150_magn: output intended variable
  iio:magnetometer:bmc150_magn: add regmap dependency
  staging: vt6656: check ieee80211_bss_conf bssid not NULL
  staging: vt6655: check ieee80211_bss_conf bssid not NULL
  iio: tmp006: Check channel info on write
  iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
  iio:light:ltr501: fix regmap dependency
  iio:light:ltr501: fix variable in ltr501_init
  iio: sx9500: fix bug in compensation code
  iio: sx9500: rework error handling of raw readings
  iio: magnetometer: mmc35240: fix available sampling frequencies
  ...